New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Fri, Nov 20, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Electricians

What happens to your home when ERCOT calls a grid emergency in Texas?

How ERCOT alerts, Energy Emergency Alerts and controlled outages work, who actually cuts and restores your power, how to register a medical need, and how to protect your home's wiring and electronics when the lights come back.

ERCOT runs the grid for about 90 percent of Texas electric load but does not own your lines or send your bill. When reserves run short it issues conservation requests, then Energy Emergency Alerts. At EEA Level 3 it orders systemwide controlled outages, which your local wires utility carries out. Report outages to that utility, not to ERCOT or your retail provider, and know that medical registration under PUC rule 25.497 does not guarantee power.

Key facts

  • ERCOT manages power for about 27 million Texas customers, about 90 percent of the state's electric load, and its grid covers about 75 percent of Texas land area (ERCOT company profile).
  • ERCOT's alert ladder is Weather Watch, Voluntary Conservation Notice, Conservation Appeal, then Energy Emergency Alert Levels 1, 2 and 3 (ERCOT TXANS).
  • EEA 1 begins when operating reserves fall below 2,500 MW, EEA 2 below 2,000 MW, and EEA 3 below 1,500 MW, when systemwide controlled outages are underway (ERCOT TXANS).
  • During Winter Storm Uri (Feb. 14-19, 2021) ERCOT's peak load shed reached 20,000 MW and about 48.6 percent of generation was forced out at the worst point (ERCOT, Feb. 24, 2021).
  • Texas DSHS confirmed 246 storm-related deaths in 77 counties for the February 2021 winter storm.
  • Critical Care and Chronic Condition designations under 16 TAC 25.497 do not guarantee the uninterrupted supply of electricity.
  • SB 3 (2021) added Utilities Code 35.0021 and 38.075, which require weather emergency preparedness for generators and wires utilities in ERCOT, with ERCOT inspections and penalties.
  • PUC rule 25.55 allows penalties of up to $1,000,000 per violation per day for weatherization violations.
  • SWEPCO's East Texas and Panhandle service area is in the Southwest Power Pool, a different grid from ERCOT (SWEPCO grid emergency page).

What is ERCOT, and does it control my power?

ERCOT stands for the Electric Reliability Council of Texas. It is a nonprofit grid operator overseen by the Public Utility Commission of Texas (PUCT) and the Texas Legislature. ERCOT says it manages the flow of power to about 27 million Texas customers, which is about 90 percent of the state's electric load, across more than 55,000 miles of high-voltage lines and more than 1,460 generating units. Its grid covers about 75 percent of the state's land area.

ERCOT schedules power plants and balances supply and demand every few seconds. It does not run the poles, transformers and service lines on your street, and it does not bill you. Those jobs belong to other companies, which is why knowing who does what saves time in an emergency.

WhoWhat they doCall them for
ERCOTRuns the statewide grid and orders controlled outages when supply is shortNothing directly. Watch ercot.com or the ERCOT app for grid status
Transmission and distribution utility (TDU), for example Oncor, CenterPoint, AEP Texas, TNMPOwns the wires and meters in retail-choice areas, carries out outages, restores serviceOutages, downed lines, meter base damage, critical care registration
Retail electric provider (REP)Sells you electricity and sends the bill in choice areasBilling, plans, starting service
City utility or electric co-op, for example Austin Energy, CPS Energy, Pedernales, BluebonnetSells and delivers power in its own areaEverything: outages, billing and medical programs

Oncor puts it plainly on its outage FAQ: it delivers electricity but is not a retailer and does not sell electricity directly to customers. If you are in Dallas or Fort Worth, Oncor is your wires company even though your bill may say another name. In Houston that role belongs to CenterPoint. See our utility outage directory for every major Texas utility's outage line.

What do ERCOT's alert levels mean?

ERCOT uses the Texas Advisory and Notification System (TXANS) to warn the public in steps. Each step is defined on ERCOT's TXANS page.

LevelWhat it means (ERCOT definition)What ERCOT asks you to do
Weather WatchSignificant weather, high demand and a potential for lower reserves are forecast. Grid conditions are still normal.Monitor conditions and review energy-saving tips
Voluntary Conservation NoticeHigher demand is forecast with lower reservesVoluntarily conserve if safe to do so
Conservation AppealHigher demand is forecast with a potential to enter emergency operationsConserve during a specific period, if safe
EEA Level 1Operating reserves below 2,500 MW and not expected to recover within 30 minutesConserve; people with critical medical needs should check with their utility
EEA Level 2Reserves below 2,000 MW, or frequency below 59.91 hertz for 15 minutesReduce use as much as possible
EEA Level 3Reserves below 1,500 MW, or frequency below 59.8 hertz for any period. Systemwide controlled outages are underwayBe prepared to lose power; conserve when you have it

A conservation appeal is a request. An EEA is an emergency. The jump between them can happen fast. On February 14 and 15, 2021, ERCOT's own timeline shows it moved from Emergency Level 1 at 12:15 a.m. to Level 3 rotating outages at 1:20 a.m., about an hour later.

One megawatt of electricity serves about 250 homes during ERCOT peak hours, according to ERCOT's October 2026 fact sheet. That helps put a 1,000 MW load-shed order in perspective: it can mean roughly a quarter of a million homes losing power at once.

What happens during a rotating outage?

When ERCOT orders load shed, it does not pick neighborhoods. It tells each utility how many megawatts to drop. Under Utilities Code 38.076, added by SB 3 in 2021, the PUCT must allocate that load-shed obligation among utilities based on their historical seasonal peak demand. Each utility then opens circuits to hit its number.

AEP Texas describes what customers should expect: assume your power could go out without advance warning; utilities do not know ahead of time who will lose power, when, or for how long; and in extreme emergencies, utilities may not be able to rotate outages without risking the stability of the whole grid. That last point is what happened during Winter Storm Uri. ERCOT reported that local utilities were limited in their ability to rotate outages because of the size of the shortfall and the number of circuits serving critical loads.

Why your neighbor kept power and you did not

Circuits that feed hospitals, 911 centers, water plants and similar critical facilities are protected as long as possible. If your home shares a circuit with one, you may stay on. Homes on other circuits carry more of the load. Utilities Code 38.078 required each wires utility to study circuit segmentation, meaning splitting big circuits into smaller pieces so outages can be spread more evenly, with reports due to the PUCT by September 1, 2024.

How long rotating outages last

There is no fixed length in state law. In a short emergency, utilities may rotate blocks in short cycles. In a deep shortfall like Uri, ERCOT's figures show load shed lasted 70.5 hours, compared with 7.5 hours in the 2011 event. Plan for the long case.

How do I know if I am in a rotating outage block?

Most Texas utilities do not publish a block number you can look up ahead of time, and AEP Texas states that utilities do not have the information to tell individual customers whether or when they will lose power during load shed. What you can do:

  • Sign up for your utility's outage alerts now. Oncor customers can text REG to 66267. Bluebonnet members can report by texting OUT to 44141.
  • Bookmark your utility's outage map, which will show your circuit's status during an event.
  • Follow ERCOT's TXANS alerts on ercot.com so you know when an EEA is declared.
  • If your power goes out during an EEA 3 and your neighbors still have power, report it anyway. It may be a separate local fault, not load shed.

If you live in a city utility area, check that utility's own pages. CPS Energy, for example, posts its own energy conservation levels and links to ERCOT grid conditions from its outage center.

Who do I call during an ERCOT outage?

Call the company that owns the wires to your home. ERCOT does not take outage reports from homes, and your retail electric provider cannot dispatch a crew. During a systemwide event, phone lines and online maps can be overloaded, so try text reporting first.

AreaUtilityOutage reporting (verified on utility site)
Dallas-Fort WorthOncor888-313-4747; text OUT to 66267 if enrolled in MyOncor Alerts
AEP Texas service areas (enter your address on aeptexas.com)AEP Texas866-223-8508
TNMP service areas (see tnmp.com)TNMP888-866-7456
AustinAustin Energy512-322-9100
San AntonioCPS Energy210-353-4357 (210-353-HELP) for electric emergencies
HoustonCenterPoint EnergyUse the outage tracker at centerpointenergy.com or the number on your bill. We could not load CenterPoint's site to confirm its phone number.

If a line is down, leave the area and call 911. Oncor's FAQ says the 911 operator will contact the utility directly.

Can I get on a critical care list for medical equipment?

Yes. PUC rule 16 TAC 25.497 creates two residential designations:

  • Critical Care Residential Customer: someone who lives in the home and has been diagnosed by a physician as dependent on an electric-powered medical device to sustain life. The designation lasts two years.
  • Chronic Condition Residential Customer: someone diagnosed with a serious medical condition that requires an electric-powered medical device or electric heating or cooling to prevent impairment of a major life function. It lasts one year if the condition is life-long, otherwise 90 days.

How to apply

  1. Get the PUCT application form from your retail provider or wires utility. REPs must give it to you on request and mention the program twice a year.
  2. Your physician completes and signs it, including a medical board license number, and sends it to the wires utility by fax or electronic means. If it goes to the REP, the REP must forward it within two business days.
  3. If the utility does not finish processing in two business days, you get a temporary designation.
  4. Watch for the renewal notice. The utility must mail it at least 45 days before the designation expires.

What it does and does not do

The designation gives you notice of planned interruptions and certain protections against disconnection for nonpayment, though you still owe your bill. It does not keep your lights on. The rule states that designation does not guarantee the uninterrupted supply of electricity, and AEP Texas warns that critical care and chronic condition customers are not excluded from controlled outages. Anyone who depends on power for life-sustaining equipment needs a backup plan: a battery system sized for the device, a safely installed generator, or a place to go. See our guide to medical equipment backup power.

City utilities and co-ops run their own medical programs. Ask your provider directly if you are served by Austin Energy, CPS Energy or a co-op.

Does all of Texas use ERCOT?

No. ERCOT covers about 90 percent of the load and about 75 percent of the land. Some Texans are on neighboring grids with their own operators and emergency procedures:

  • East Texas and the Panhandle (SWEPCO): SWEPCO says its East Texas and Panhandle service territory is in the Southwest Power Pool (SPP), a different grid. It gives the example that Mineola, Gladewater, Kilgore and Longview are in SPP while nearby Tyler is in ERCOT. In an SPP emergency, SWEPCO says it may run rotating controlled outages in parts of its territory.
  • Far West Texas (El Paso Electric): El Paso Electric serves about 465,000 customers in an area from Hatch, New Mexico, to Van Horn, Texas. Its outage line in Texas is (915) 877-3400. ERCOT's TXANS alerts do not describe conditions on its system.
  • Other areas: Some Southeast Texas and Panhandle customers are served by other investor-owned utilities that are outside ERCOT. Check your utility's grid emergency page to learn which grid you are on.

If you are outside ERCOT, an ERCOT conservation appeal on the news may not apply to you, and your utility's alerts are the ones that matter.

What changed after Winter Storm Uri?

Winter Storm Uri in February 2021 was the worst grid event in Texas history. ERCOT reported 20,000 MW of peak load shed and generation outages peaking at 52,277 MW, about 48.6 percent of installed capacity. Grid frequency fell below 59.4 hertz for 4 minutes and 23 seconds on February 15; ERCOT said more units would have tripped if that had lasted 9 minutes or more. Texas DSHS confirmed 246 storm-related deaths in 77 counties.

Before the storm, ERCOT told lawmakers that generators were not required to meet any minimum weatherization standard and that no entity had rules to enforce one. The 2021 Legislature changed that:

Law or ruleWhat it does
SB 3 (2021), Utilities Code 35.0021Requires generators selling power in ERCOT to prepare for weather emergencies under PUCT standards; ERCOT inspects and reports violations; penalties for violations not fixed in a reasonable time
SB 3, Utilities Code 38.075Same duty for co-ops, city utilities and transmission and distribution utilities in ERCOT
SB 3, Utilities Code 38.076Load-shed allocation system, critical load categories and load-shed plans filed with the PUCT and ERCOT
SB 3, Utilities Code 38.074Designation of critical natural gas facilities so they are prioritized during load shed
SB 2 (2021), Utilities Code 39.1513Created a selection committee appointed by the governor, lieutenant governor and House speaker to pick ERCOT board members
PUC rule 16 TAC 25.55 (effective Nov. 10, 2021, amended 2022)Winter preparations by December 1 and summer preparations by June 1 each year, notarized declarations, ERCOT inspections, and penalties up to $1,000,000 per violation per day

SB 3 also set backup-power planning requirements for water and sewer utilities, which the PUCT noted in its Hurricane Beryl review.

Is the Texas grid ready for this winter or summer?

No one can promise a grid will not fail in an extreme event, and ERCOT's readiness changes every season. Two facts are worth knowing. First, demand keeps climbing: ERCOT's fact sheet lists an unofficial record peak of 91,155 MW on July 22, 2026. Second, the supply mix has changed, with large amounts of solar and battery storage now on the system (ERCOT lists 21,537 MW of installed storage as of October 2026), which helps most in summer evenings.

Also remember that most long Texas outages are not grid shortages. Hurricane Beryl in July 2024 left 2.7 million customers without power, including 2.2 million CenterPoint customers, because of damage to local lines, not an ERCOT emergency. The PUCT found most vegetation-related outages were caused by trees outside utility easements. Your home plan should cover both kinds of outages. See our hurricane electrical safety guide.

How do I protect my home's wiring and electronics when power returns?

The moment power comes back is hard on equipment. Every motor and compressor on the circuit tries to start at once, and voltage can swing. Simple steps reduce damage:

  1. Unplug sensitive electronics such as computers, TVs and chargers when the power goes out, or switch off their surge strips.
  2. Turn off the AC at the thermostat and large appliances like electric water heaters and dryers. Leave one light on so you know when power returns.
  3. Wait a few minutes after power returns, then turn on large loads one at a time. Many outage restorations include brief re-trips as the utility rebalances circuits.
  4. Consider whole-house surge protection. Since the 2020 NEC, new and replaced dwelling services need a surge-protective device at the service. Texas now uses the 2026 NEC statewide. See whole-house surge protection.
  5. Never backfeed. Plugging a generator into a wall outlet sends power back up the line. CPSC warns this can electrocute utility workers and neighbors on the same transformer. Use a listed transfer switch or interlock installed by a licensed electrician. See transfer switches and interlocks.
  6. Run generators outdoors only, far from doors, windows and vents, and keep battery-backed CO alarms inside. CPSC says most generator incidents it hears about involve carbon monoxide.

When to call an electrician after an outage

  • Only part of the house came back, or lights are much brighter or dimmer than normal. That can mean a lost neutral, which is dangerous. Call your utility first, then an electrician.
  • You smell burning or see scorching at outlets or the panel.
  • A breaker will not reset or trips again right away. See breaker keeps tripping.
  • The meter base, weatherhead or service mast was damaged. Your utility will not reconnect until a licensed electrician repairs customer-owned parts and any required city inspection passes. See meter base responsibility.

What should businesses do during grid emergencies?

Businesses face the same load-shed rules as homes. AEP Texas states that customers designated as critical load are not guaranteed uninterrupted service and that it is the customer's responsibility to arrange alternative power. A practical plan:

  • Know your wires utility and account numbers, and keep the outage line in your phone.
  • Ask your utility whether you qualify as a critical load public safety or critical load industrial customer under rule 25.497. Hospitals, police and fire stations and critical water facilities are examples.
  • Have a licensed electrician size and install a standby generator or battery system with a proper transfer switch for the loads you cannot lose: refrigeration, servers, security and medical equipment. See standby generators.
  • Write a shutdown and restart sequence so equipment does not all restart at once.
  • Check your business insurance for spoilage and business interruption coverage before the season starts.

Utilities Code 38.075(e) lets wires utilities run load management programs for nonresidential customers during an ERCOT Level 2 emergency or higher. Ask your utility if one is offered.

Does insurance pay for food or damage from a grid outage?

Sometimes. The Texas Department of Insurance says most homeowners and renters policies pay up to $500 or more for food spoiled when the power fails under certain circumstances, often with no deductible. Policies usually do not pay for a hotel during an outage unless the home was damaged by a covered event. Read your policy or call your agent. TDI's consumer Help Line is 800-252-3439.

Some utilities provide a letter confirming an outage at your address. Oncor and AEP Texas both offer outage verification letters, which can help with an insurance claim.

How to choose a provider

  • Find out who owns the wires to your home (your TDU, city utility or co-op) and save its outage line.
  • Sign up for your utility's text outage alerts and ERCOT TXANS notices.
  • If anyone in the home relies on powered medical equipment, have a physician submit the 25.497 application and calendar the renewal date.
  • Build a backup plan that does not depend on the designation: batteries for medical devices, a safely installed generator, or a place to go.
  • Have a licensed electrician install a transfer switch or interlock before you ever connect a generator.
  • Keep battery-backed CO alarms in the home if you will use a generator.
  • During an EEA, unplug sensitive electronics and turn the AC off at the thermostat.
  • After power returns, restart large loads one at a time.
  • Call an electrician if lights are unusually bright or dim, a breaker will not reset, or the meter base is damaged.
  • Review your insurance for food spoilage and outage-related coverage.

Related electricians guides

Electricians by state and city

Questions people ask

What is the difference between an ERCOT conservation appeal and an EEA?

A conservation appeal is ERCOT asking the public to use less power during a set period because emergency operations are possible. An Energy Emergency Alert means reserves have already dropped below set levels: under 2,500 MW for EEA 1, under 2,000 MW for EEA 2, and under 1,500 MW for EEA 3. Controlled outages happen at EEA 3. Conserving during an appeal can help keep the grid from reaching that point.

Will ERCOT warn me before my power is cut?

ERCOT warns the public through TXANS before and during emergencies, but it does not notify individual homes. Utilities carry out controlled outages, and AEP Texas states customers should assume power could go out without advance warning because utilities do not know in advance who will be affected or for how long. Sign up for your utility's alerts so you hear about restoration.

Why do Austin Energy and CPS Energy have different rules?

Austin Energy is a department of the City of Austin, and CPS Energy serves San Antonio directly. In those cities you buy power from the local utility instead of picking a retail provider, so the utility handles outages, billing and medical programs itself. They still follow ERCOT load-shed orders, and SB 3's weatherization duty in Utilities Code 38.075 applies to city utilities and co-ops in ERCOT.

Does a critical care designation stop rotating outages at my house?

No. Rule 16 TAC 25.497 says designation does not guarantee uninterrupted electricity, and AEP Texas states these customers are not excluded from controlled outages. The designation mainly gives notice of planned interruptions and some protections against disconnection for nonpayment. Keep a backup plan for any life-sustaining device, and know where you will go if the outage runs long.

Should I call my retail electric provider when my power goes out?

No. In Texas retail-choice areas, your retail provider sells you electricity but does not own the lines. Report outages to your transmission and distribution utility, such as Oncor, CenterPoint, AEP Texas or TNMP. Your retail provider is the right call for billing questions, plans and starting or stopping service. Oncor's FAQ makes this distinction directly.

Can I run my house on a generator during an ERCOT emergency?

Yes, if it is connected the right way. A licensed electrician should install a listed transfer switch or panel interlock so the generator cannot feed power back onto utility lines. CPSC warns that plugging a generator into a wall outlet can electrocute utility workers and neighbors. Run the generator outdoors, far from openings, and keep battery-backed CO alarms inside.

Is El Paso on the ERCOT grid?

El Paso Electric serves about 465,000 customers from Hatch, New Mexico, to Van Horn, Texas, and ERCOT's own figures show it covers about 90 percent of Texas load, not all of it. ERCOT's TXANS alerts describe ERCOT conditions only. If you live in El Paso, follow El Paso Electric's alerts and report outages at (915) 877-3400.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration