New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Electricians

Home Battery Backup: What Electrical Work Is Needed, How Long Will It Run, and What Do Texas and Florida Rules Say?

A neutral, code-focused guide to home batteries such as Tesla Powerwall, Enphase and FranklinWH: whole-home vs. partial backup, the gateway and panel work, permits after Texas SB 1252, garage and flood-zone placement, runtime math for air conditioning, and ERCOT's virtual power plant pilot.

A home battery can power your whole house only if its power output (kW) covers your biggest loads and its stored energy (kWh) lasts as long as the outage. Most installs back up selected circuits through a backup gateway or transfer device that disconnects the home from the grid during an outage. The work requires a licensed electrician and, if the battery can push power to the grid, a utility interconnection agreement. You do not need solar, but without it the battery cannot recharge during a long outage.

Key facts

  • Texas SB 1252 (effective September 1, 2025) bars cities from adopting NEC amendments or other rules that regulate installation or inspection of residential energy backup systems of up to 50 kW or 100 kWh; city-owned utilities may still regulate them, per TDLR.
  • TDLR says all non-exempt electrical work on residential energy backup systems must follow Occupations Code ch. 1305 and the NEC and be done by licensed electrical contractors with licensed electricians.
  • Oncor requires an interconnection agreement for a battery system that operates in parallel with the utility and can discharge into the grid.
  • Austin Energy requires an Auxiliary Power electrical permit and a final inspection before solar and battery systems in its service area can be turned on.
  • NEMA's 2026 water-damage guide lists batteries and energy management systems as replace items and notes the NEC (706.3) says reconditioned energy storage systems shall not be installed.
  • ERCOT's Aggregate Distributed Energy Resource (ADER) pilot, established through PUCT Project No. 53911, tests aggregations of many small sites responding to ERCOT dispatch; its Phase 3.3 governing document is dated June 3, 2026.
  • IAEI explains that NEC 706.30 limits dwelling energy storage systems to 100 volts unless live parts are not accessible during routine maintenance.
  • LBNL's August 2026 survey of building departments found home battery permit fees grouped with other categories at medians near $100, with wide local variation.

Can a home battery power my whole house?

It can, but only if you size it for that. Two numbers matter, and people mix them up:

  • Power (kilowatts, kW): how much the battery can deliver at one moment. It decides what can run at the same time, and whether it can start a big motor like a central AC compressor or a well pump.
  • Energy (kilowatt-hours, kWh): how much the battery stores. It decides how long things can run.

A whole-home backup design puts the entire panel behind the battery system. A partial (or essential-loads) design moves selected circuits, such as the refrigerator, lights, internet, outlets, a gas furnace fan, a well pump or medical equipment, to a backed-up subpanel. Partial backup stretches the battery much further.

Whole-home vs. partial backup

DesignHow it is wiredProsCons
Whole-homeBackup gateway or transfer equipment at the service, ahead of the main panelNo circuits to choose; everything worksBig loads drain the battery fast; may need more battery capacity or load control
PartialCritical loads moved to a subpanel fed through the battery systemLonger runtime from the same batteryOnly chosen circuits work in an outage; panel rework
Whole-home with load controlWhole-home wiring plus smart breakers or relays that shed big loadsFlexibleMore equipment and programming

How long does a home battery last in an outage, and how many do I need to run AC?

Runtime is simple math: usable battery energy (kWh) divided by your average load (kW) equals hours. The hard part is knowing your load.

Example (illustrative numbers only)

Suppose your battery system has 13 kWh of usable energy. If your essential loads (refrigerator, lights, fans, internet, a few outlets) average 0.5 kW, that is about 26 hours. If you add a central AC unit that pushes your average to 3 kW, that drops to about 4 hours. Your numbers will be different. The point is that air conditioning, electric water heaters, pool pumps, electric dryers and EV chargers decide runtime in Texas and Florida homes.

Getting your real numbers

  • Look at your hourly usage. In much of Texas, wires companies such as Oncor point customers to Smart Meter Texas for detailed data. Florida utilities show usage in their online accounts.
  • Check the AC condenser's data plate for running amps and locked-rotor amps (the start-up surge). The battery system's power rating, and any soft starter on the AC, must handle that surge.
  • Ask the installer for a written runtime estimate for summer and winter, with and without AC.

How many batteries to run AC?

There is no universal number. It depends on the AC unit's size and efficiency, your thermostat setting, how hot it is, and the battery model's power and energy ratings. Many households run AC sparingly during outages, or add a soft starter so the battery can start the compressor. Get the manufacturer's specifications for the exact model and have the installer show how many units it takes to start and run your AC for the hours you want.

Do I need solar to get a home battery?

No. A battery can charge from the grid and hold that energy for an outage. Without solar, though, it cannot recharge during a multi-day outage, so it becomes a one-time reserve. With solar, the panels can recharge it each sunny day, which is what makes multi-day backup possible.

Also note that grid-tied solar without a battery shuts off during an outage. Florida's interconnection rule for investor-owned utilities requires equipment that automatically isolates customer generation from the grid when the grid loses power (FAC 25-6.065), and the NEC requires interactive equipment to disconnect on loss of the primary source, as IAEI explains for 705.40. A battery and backup gateway let the solar keep working for your home while staying isolated from the grid. See solar and your home's electrical system.

What electrical work is needed for a home battery?

A battery installation is a power source connected to your home's wiring, so it involves more than hanging a box on the wall. Expect some or all of the following:

  • A backup gateway or transfer device. This senses a grid outage, opens the connection to the utility, and lets the battery power your home as an island. It is what keeps the battery from backfeeding the grid and endangering lineworkers.
  • A point of connection. The NEC (705.12) allows a power source to connect on the supply side of the service disconnect or on the load side at distribution equipment, with limits on how much current a panel's busbar can carry. Your installer picks the connection that fits your panel.
  • A critical loads subpanel for partial backup, with selected circuits moved into it.
  • Disconnecting means. NEC 706.8 requires that a disconnect serving multiple power sources disconnect all of them when off, according to IAEI. The 2020 NEC also added outdoor emergency disconnect requirements for one- and two-family dwellings, with similar rules for energy storage systems, per Miami-Dade's 2020 NEC summary.
  • Labels and a power source directory at the service and at each power source, so firefighters and future electricians know the home has a battery. IAEI notes the original installer is often not around when the system needs service.
  • Dwelling voltage limits. IAEI explains that 706.30 limits dwelling energy storage systems to 100 volts between conductors or to ground, unless live parts are not accessible during routine maintenance.
  • Panel or service work, if the existing panel is full, obsolete, or cannot accept the connection.

Who can do it:

  • Texas: TDLR says all non-exempt electrical work on residential energy backup systems must follow Occupations Code ch. 1305 and the NEC, and be done by licensed electrical contractors with licensed electricians.
  • Florida: a certified or registered electrical contractor under chapter 489 part II, or an owner-builder working on their own single-family home or duplex (s. 489.503(6)). Solar contractors licensed under chapter 489 part I may install photovoltaic systems and related equipment (s. 489.105); ask any installer which license covers the battery and service work.

Do home batteries need permits and fire separation?

Texas: SB 1252 changed local control

Senate Bill 1252, effective September 1, 2025, defines a residential energy backup system as one installed at a residence that can provide no more than 50 kilowatts or has storage capacity of no more than 100 kilowatt-hours. TDLR summarizes the law this way:

  • A municipality may not adopt or enforce an NEC amendment, ordinance, rule or other measure that would regulate the installation or inspection of a residential energy backup system.
  • A municipally owned utility may regulate installation or inspection within its service area. That covers places served by city utilities, such as Austin Energy and CPS Energy.
  • All such work still must follow Occupations Code ch. 1305 and the NEC (the 2026 NEC since September 1, 2026) and be done by licensed Texas electrical contractors and electricians.

A second 2025 law, SB 1202, is about permit speed, not local control. It added Local Government Code 247.0025, which covers home backup power installations (generators, energy storage and standby systems serving a one- or two-family home, connected at 600 volts or less). A qualified third party, such as an electrical inspector or certain licensed master electricians, may review the required documents or perform the inspection without first going through the city or county. The local authority must post its rules and fee schedule online (or send them within two business days of a request), may not charge a fee if it has not posted one, and must issue the approval or permit by the third business day after it receives notice of the third party's approval. The reviewer, not the city, is liable for negligent reviews. This is separate from the 2023 HB 14 rule in Sec. 247.002, which lets a qualified third party step in when a city misses its review or inspection deadline by 15 days.

What this means in practice is still settling. In Austin Energy's territory, the utility requires an Auxiliary Power electrical permit from Austin Development Services and a final solar and battery inspection before the system can be turned on. In cities served by investor-owned utilities, such as Houston, Dallas and Fort Worth, ask the building department how it handles battery projects after SB 1252, and ask your utility about interconnection. This is a new law; check with TDLR if a city's requirements seem to conflict with it.

Florida

Florida building departments permit and inspect battery systems under the Florida Building Code, which references the NEC (2020 NEC in the 8th Edition; 2023 NEC in the 9th Edition, effective December 31, 2026 per the state or January 1, 2027 per Tampa). Expect an electrical permit, and in some cases building or fire review.

Fire separation and size limits

Residential building and fire codes, including section R328 of the International Residential Code and NFPA 855, set rules for where energy storage systems can be installed in homes, total capacity per location, separation from living space, and protection from vehicle impact in garages. We could not load the current text of these codes for this guide, so we do not quote specific limits. Ask your installer which code sections and editions your building department enforces, and ask to see the battery system's safety listing and installation manual.

Can batteries be installed in a garage?

Often yes, subject to the residential code your jurisdiction enforces and the manufacturer's manual. Questions to ask:

  • Does the code require protection from vehicle impact, such as bollards or a minimum height, for a garage installation?
  • What clearances does the manufacturer require around the unit and from doors, windows and vents?
  • Is the garage within the temperature range the manufacturer allows? Texas and Florida garages can get very hot in summer, which can reduce performance or trigger thermal limits.
  • Is there a smoke alarm or heat detector requirement for the space?
  • In flood-prone areas, is the unit mounted above the design flood elevation?

Outdoor wall mounts are common in Texas and Florida. Shade helps with heat. Never mount a battery where it blocks the meter, the panel's working space, or an exit.

Flood-zone and hurricane placement

Water and lithium-ion batteries do not mix. NEMA's 2026 guide on water-damaged equipment lists batteries and energy management systems as items to replace after water exposure, and notes that the NEC (706.3) says reconditioned energy storage systems shall not be installed. NEMA also says that batteries exposed to moisture for long periods can corrode and eventually release their internal contents.

  • Mount high. Federal floodplain rules require equipment in new construction and substantial improvements in flood-prone areas to be designed or located to prevent water from entering or accumulating in it (44 CFR 60.3). Ask your floodplain administrator for the design flood elevation and mount above it.
  • Before a hurricane, set the battery app to keep a full reserve (often called storm or backup-only mode).
  • If a battery is flooded, do not touch it, do not re-energize the home, and call the installer and the fire department if you see swelling, smoke, hissing or heat.
  • Insurance: ask your agent whether the battery is covered as part of the dwelling, and how flood is handled. TDI says Texas home policies do not cover flood.

See flood-damaged electrical and hurricane electrical safety.

Do I need to tell my utility, and what is interconnection?

If your battery can operate in parallel with the grid and discharge into it, yes. Oncor says a battery system that operates in parallel with the utility for any length of time and can both charge and discharge into the utility system requires an interconnection agreement. Batteries paired with solar almost always need one, and you should not turn the system on until you receive permission to operate.

In Florida, investor-owned utilities such as FPL, Duke Energy Florida and Tampa Electric follow the state's interconnection rule (FAC 25-6.065) for customer-owned renewable generation, and municipal utilities and co-ops have their own programs under s. 366.91. Ask your utility how it treats a battery added to an existing solar system; Oncor, for example, requires a new application when equipment is added to an existing renewable system.

A battery used only as backup, charged from the grid and isolated by a break-before-make transfer device, may be treated differently. Ask your utility in writing.

Can I join a virtual power plant in Texas?

A virtual power plant (VPP) links many home batteries, and sometimes EV chargers and thermostats, so they can respond together to grid needs. In Texas, ERCOT runs the Aggregate Distributed Energy Resource (ADER) Pilot Project, established through PUCT Project No. 53911. ERCOT describes an ADER as a resource made up of multiple individually metered sites connected at the distribution level that can, in aggregate, respond to ERCOT dispatch instructions.

  • Homeowners do not sign up with ERCOT directly. Participation runs through a company that registers the aggregation with ERCOT and the PUCT, often in partnership with a retail electric provider.
  • ERCOT posted a Phase 3.3 governing document on June 3, 2026, and in November 2026 published stakeholder comments on a Phase 4 governing document from groups including Oncor, CenterPoint, the Texas REP Coalition, Base Power and Qcells. The program is still evolving.
  • Ask any VPP offer: how much of my battery can you use, how often, how much reserve is kept for my own outages, what do I earn, and can I opt out?

Austin Energy and CPS Energy customers are served by city-owned utilities; ask your utility about its own battery or demand response programs. Austin Energy's Power Partner EV program, for instance, already manages enrolled EV chargers during peak events.

Florida does not have an ERCOT-style market. Ask your utility whether it offers any battery program.

Battery vs. generator for hurricanes and winter storms

FactorHome batteryStandby generator
Short outages (hours)Excellent; instant and silentGood; starts in seconds
Multi-day outagesNeeds solar to recharge; weather dependentRuns as long as fuel lasts
Central ACPossible with enough capacity, drains fastYes, if sized for it
Carbon monoxideNoneExhaust must be kept away from openings
FloodingReplace if submerged (NEMA)Enclosure must stay above water
Texas HOA protectionSolar devices protected (Prop. Code 202.010); batteries not specifically addressedStandby generators protected (Prop. Code 202.019)
Texas city rulesLimited by SB 1252 for systems up to 50 kW or 100 kWhNormal local permits

See standby generators and portable generator hookups.

What does a home battery cost to install?

We did not find a recent, independent, dated study of installed home battery prices in Texas or Florida, so we do not publish a range. What we can source:

  • Permit fees: LBNL's August 2026 survey of building departments found home battery installation permits grouped with EV charger, panel, plumbing and HVAC permits at medians near $100, with wide variation by jurisdiction.
  • Panel work, if needed: the same LBNL survey found a median main panel replacement cost of $3,500 in single-family homes.

Price drivers include the number of battery units, whole-home vs. partial backup, gateway and subpanel work, distance between the battery and the panel, wall or pad mounting, and permit requirements. Get two or three itemized quotes with the same backup design, and compare runtime estimates, warranties and who handles interconnection. Texas residential solar sales and leases have new contract and cancellation rules under the Residential Solar Retailer Regulatory Act; see our solar guide.

How to choose a provider

  • Decide what must run during an outage and for how long.
  • Collect your hourly usage data and the AC's data plate ratings.
  • Choose whole-home, partial, or whole-home with load control.
  • Ask for a written runtime estimate for summer and winter.
  • Confirm the installer's license (TDLR in Texas; DBPR in Florida) and who pulls permits.
  • In Texas, ask how SB 1252 affects permits in your city, and whether your city-owned utility has its own rules.
  • Ask which fire and residential code sections apply to the location (garage, outdoor, indoor).
  • Mount above the flood elevation in flood-prone areas.
  • Get the interconnection agreement and permission to operate before turning on any grid-parallel system.
  • Set a storm reserve before hurricane season and know how to check the system after a storm.

Related electricians guides

Electricians by state and city

Questions people ask

Will a home battery keep my power on automatically when the grid fails?

Yes, if it is installed with a backup gateway or transfer device. When the grid fails, the device disconnects your home from the utility and the battery takes over the backed-up circuits, usually quickly enough that many devices keep running. Without that equipment, a grid-tied battery and solar system shuts down in an outage to protect lineworkers. Ask the installer to show you exactly which circuits stay on.

Can I add a battery to my existing solar system?

Usually, but it is a design project. The installer must check inverter compatibility, the point of connection on your panel, and whether a backup gateway is needed. Your utility may require a new interconnection application; Oncor, for example, requires a new application when equipment is added to an existing renewable system. Get a new permit and wait for approval before operating the changed system.

Does Texas SB 1252 mean my city cannot inspect my battery?

SB 1252 bars cities from adopting or enforcing NEC amendments, ordinances or other measures that regulate installation or inspection of residential energy backup systems up to 50 kW or 100 kWh, according to TDLR. City-owned utilities can still regulate them in their service areas. The work must still meet the NEC and be done by licensed electricians. Ask your city and utility how they handle these projects now, and contact TDLR with questions.

Is it safe to have a lithium-ion battery attached to my house?

Listed systems installed to the manufacturer's instructions and the applicable codes are designed to manage the risks, which include heat, physical damage and water. Follow the location and clearance rules, keep it away from vehicle impact, keep the area clear of storage, and never ignore swelling, odors, smoke or alarms. After a flood, NEMA lists batteries as replace items. Call the fire department for any battery fire.

Can a home battery run my well pump?

Often yes, if the battery's power rating can handle the pump motor's starting surge and the pump circuit is on the backed-up panel. Well pumps, like AC compressors, draw a large current for a moment when they start. Give the installer the pump's voltage, horsepower and amperage, and ask them to confirm in writing that the system can start and run it.

How long do home batteries last before they need replacing?

Battery life depends on the chemistry, how often it cycles, and heat. Manufacturers state warranty terms in years and in energy throughput or remaining capacity, and those terms differ by model. Read the warranty for your exact product, including conditions about operating temperature, which matters in Texas and Florida garages, and whether participation in a utility or VPP program affects coverage.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration