Local Guide · Electricians
Electrical Panel Upgrade (100A to 200A): Cost, Process, Permits and Timeline
A complete Texas and Florida guide to replacing a breaker panel or upgrading service: what each job includes, real cost and timeline data from LBNL's 2026 survey, load calculations and load-management alternatives, utility coordination, permits and the code items a new panel triggers.
Upgrading from 100 to 200 amps usually means a new panel plus new service equipment, often a new meter base, with utility coordination, a permit and an inspection. LBNL's August 2026 national survey found median single-family costs of $3,500 for a main panel replacement and $2,800 in customer-side equipment for a service increase, plus a median $3,500 when utility-side costs were passed on. Most single-family jobs finished within 30 days. A load calculation may show you can avoid the service upgrade.
Key facts
- LBNL (Aug. 2026): median single-family main panel replacement cost $3,500 (IQR $2,100 to $5,000; mean $3,931; 34 responses).
- LBNL (Aug. 2026): for a single-family service rating increase, median customer-side equipment cost $2,800 (IQR $2,000 to $5,000) and median utility-side cost passed to the customer $3,500 (IQR $1,650 to $7,000).
- LBNL (Aug. 2026): 70% of single-family projects without a service increase, and 64% with one, were completed within 30 days, per building industry respondents.
- LBNL (Aug. 2026): residential electrical permit fees mostly clustered near a $100 median; nearly all utility respondents reported no allowance for service rating increases.
- LBNL's 2023 ENERGY STAR presentation describes NEC 220.87 as using metered 15-minute peak load x 1.25 plus the new load, and 220.83 as 100% of the first 8,000 watts plus 40% of remaining loads.
- Miami-Dade's 2020 NEC summary says 220.87 cannot be used where the service has solar or other peak load shaving, because actual maximum demand is not obtainable.
- The 2020 NEC added whole-house surge protection for dwelling services (230.67), including where service equipment is replaced, and an outdoor emergency disconnect for one- and two-family homes (230.85).
- Texas adopted the 2026 NEC effective September 1, 2026; Florida's 9th Edition Building Code (2023 NEC) takes effect December 31, 2026 per the state (Tampa says January 1, 2027).
- Florida's permit statute exempts some small jobs under $7,500 but not electrical work on single-family homes (s. 553.79).
The short version
A panel upgrade can mean three different jobs, and the price, timeline and paperwork depend on which one you need:
- Panel replacement only. The breaker panel is swapped for a new one of the same or similar rating. The utility's service and meter stay the same.
- Service upgrade. The service rating goes up, for example from 100 amps to 200 amps. That usually means a new panel and new service entrance wires, often a new meter base, and sometimes a bigger utility service drop or transformer.
- Load management instead. A load calculation, a smart panel, or a load-control device shows the existing service can handle the new load, and no service increase is needed.
The best published national data come from a Lawrence Berkeley National Laboratory (LBNL) survey published in August 2026. It found a median of $3,500 for a single-family main panel replacement, a median of $2,800 in customer-side equipment for a service rating increase, plus a median of $3,500 in utility-side costs passed to the customer when the utility side had to change. Most single-family projects were finished within 30 days. Those are national survey figures, not Texas or Florida quotes, and the samples were small. Details are below.
Panel vs service vs meter base: what each part is and who owns it
Knowing the parts helps you read quotes and understand who does what.
| Part | What it is | Usually owned by |
|---|---|---|
| Service drop or lateral | The overhead wire from the pole (drop) or underground cable from the transformer (lateral) to your house | Utility, for overhead drops at Oncor, FPL, TECO and JEA; Austin Energy owns the cable inside the conduit for underground service |
| Weatherhead, riser and service entrance cable | The hooded cap and pipe at the roofline and the wires from it down to the meter | Customer at Oncor, FPL, TECO and JEA; Austin Energy puts the service entrance cable and point of attachment on the customer |
| Meter | The utility's measuring device | Utility (Oncor, Austin Energy, CPS Energy, FPL, TECO, JEA) |
| Meter base (meter socket, meter can) | The box the meter plugs into | Customer at Oncor, Austin Energy, FPL, TECO and JEA |
| Service disconnect / main breaker | The switch that shuts off all power to the house | Customer |
| Panel (load center, panelboard) | The box with the breakers for each circuit | Customer |
| Grounding electrode system | Ground rods or other electrodes and the conductor connecting them | Customer (FPL lists the ground wire and rod as homeowner-owned) |
CPS Energy in San Antonio says its responsibility ends where service reaches the building, at the weatherhead or meter can. We could not load an AEP Texas source on ownership, and CenterPoint's site could not be loaded; a 2024 CenterPoint chart quoted by KPRC put meter box and weatherhead repairs on the customer. Confirm with your utility. Our page on meter base and service drop responsibility goes deeper.
What is a meter-main combo?
A meter-main (or meter-main combination) is a single outdoor enclosure that holds the meter socket and the main service disconnect, and sometimes a set of breakers. Many Texas and Florida homes have their meter and main outside already. Meter-main combos are a common way to provide the outdoor emergency disconnect that the 2020 NEC (Section 230.85) requires for one- and two-family homes, so firefighters can shut off power without pulling the meter. With a meter-main outside, the indoor panel becomes a subpanel fed from it.
How do I know if I need a panel upgrade?
Common reasons fall into four groups.
1. Safety or condition problems
- Breakers that will not reset, trip without cause, or are hot, buzzing or scorched.
- Burn marks, melted parts, rust or water damage in the panel. NEMA's 2026 guidance says molded-case breakers exposed to water should be replaced.
- A fuse box, especially one with signs of over-fusing.
- A panel brand that inspectors or insurers flag, such as Federal Pacific Stab-Lok or Zinsco. LBNL's 2023 ENERGY STAR presentation listed old, unsafe or damaged panels, fuse boxes, and Zinsco/GTE Sylvania and Federal Pacific panels as cases where "an update is needed." See Federal Pacific and Zinsco panels.
- Double taps (two wires under one breaker screw not rated for it), wrong-size breakers or improper grounding. Florida's Citizens 4-point inspection form asks inspectors to report all of these.
2. Insurance
Florida's Citizens Property Insurance requires a 4-point inspection for homes more than 20 years old, and its form records panel amperage, whether the amperage is sufficient, panel age, year last updated, and brand and model. Citizens tells agents not to submit applications for homes with existing hazards. In Texas, TDI's rule says insurers cannot decline or non-renew a policy just because a home or its wiring is old, but may consider the physical condition of wiring. See Florida 4-point inspections.
3. Not enough capacity
You are adding a big load: an EV charger, a heat pump, an electric range or water heater, a pool or spa, a workshop, a home addition, or solar and batteries. LBNL's 2023 presentation said utilities report that the main drivers of panel and service changes are solar PV and EV charging. Heat pumps alone were a smaller factor in the data LBNL cited.
4. Not enough space
Every slot is full and there is no room for new circuits. LBNL cited a BayREN electrification checklist that found 31% of 100-amp panels and 48% of 200-amp panels had free breaker space (California data). Space and capacity are different problems: a full panel may have plenty of capacity and need only a subpanel, while a panel with empty slots can still be overloaded.
Is 100 amp service enough for a house?
It depends on what is in the house, not just its size. A 100-amp service can be enough for a modest home with gas heat, gas cooking and a gas water heater. It can be tight for an all-electric home with central AC, electric heat strips, an electric range, dryer and water heater, especially if you add an EV charger.
What the data show:
- In about 18,000 home electrification projects LBNL cited (mostly California single-family homes), installed panels were roughly 30% 100 amps, 50% 200 amps and 15% 125 amps.
- In one California program LBNL cited, only 480 of 10,446 heat pump upgrades (4.6%) involved a panel replacement, and most of those went from 200 to 300 amps rather than from 100 to 200.
- LBNL's August 2026 report notes that analysis of Pecan Street data from Texas suggests homes with panels under 200 amps face a higher likelihood of needing significant electrical improvements when adding new electric loads.
Texas and Florida homes differ from California ones: most have central AC, and many are all-electric. That makes a proper load calculation more important, not less. The only reliable answer for your home is a load calculation, explained next.
What is a load calculation and do I need one?
A load calculation estimates the most power your home will draw at once, using rules in Article 220 of the National Electrical Code. It is how an electrician decides whether your existing service can take a new load, and many building departments ask for it with a service upgrade permit. For an existing home, the NEC offers more than one method, and the choice can decide whether you need an upgrade at all.
Method 1: Calculated existing load (NEC 220.83)
LBNL's 2023 ENERGY STAR presentation summarizes this method. You add up the connected loads in the home, then count 100% of the first 8,000 watts and 40% of the rest. If you are adding new heating or cooling, the larger of the heating or cooling load is added in as well. This method uses nameplate ratings, so it tends to be conservative.
Method 2: Measured existing load (NEC 220.87)
Instead of estimating, this method uses the home's actual highest demand from metering data. LBNL summarizes it as: take the highest measured load (based on 15-minute interval data), multiply by 1.25, and add the new load. Many homes use far less power at peak than their nameplate totals suggest, so this method can show room for an EV charger or heat pump without a service upgrade.
Two limits to know:
- Miami-Dade's summary of the 2020 NEC (the code behind Florida's current 8th Edition) notes that 220.87 permits actual maximum demand values, but that where the service has a renewable energy system such as solar, or any form of peak load shaving, actual maximum demand is not obtainable and 220.87 cannot be used.
- You need a full year of good data, or an accepted alternative. Ask your electrician and building department what they accept.
The Texas smart-meter advantage
Oncor says its standard advanced meters record 15-minute interval usage data that customers can access through Smart Meter Texas. That is the same 15-minute interval LBNL describes for the 220.87 method. If you are in an area served by a Texas TDU with advanced meters, ask your electrician whether your interval history can support a measured-load calculation. Florida utilities also use smart meters; ask yours how to download interval data.
LBNL's 2023 presentation suggested that some unnecessary panel and service changes come from simplified approaches that do not use existing NEC paths such as metered data, and that some local code authorities are not prepared for newer methods. Asking for the calculation, and the method used, is reasonable.
Can I avoid a panel upgrade with a load management device?
Often, yes. LBNL's 2023 ENERGY STAR presentation listed several ways to add electric loads without a service upgrade, with rough 2023 costs:
| Option | What it does | 2023 cost range cited by LBNL | Complexity |
|---|---|---|---|
| Circuit sharing (circuit splitter) | Lets two 240-volt loads share one circuit, such as a dryer and an EV charger, so only one runs at full power at a time | $300 to $600 plus installation when hard-wired | Least complicated; some plug-in versions |
| Circuit pausing | A relay turns a load off when total home demand nears about 80% of the rated capacity, measured with current sensors on the mains or feeder | $400 to $900 plus installation | Medium; needs current sensors and communication hardware |
| Smart panel | Replaces the panel with one that monitors and can switch individual circuits to keep the total under a limit | $3,000 to $5,000 plus installation | Most complicated, most flexible |
| Meter collar | A device between the meter and meter socket that can connect solar or an EV charger | Not priced | Requires utility approval |
| Lower-power appliances | 120-volt heat pump water heaters, 120-volt induction, heat pump dryers, limiting EV charging to about 7.2 kW | Varies | Simple |
| NEC load calculations | Using 220.83 or 220.87 correctly before assuming an upgrade | Labor for the calculation | Simple |
LBNL noted that a circuit-pausing device saves panel load but not physical space, and that tandem breakers and subpanels can help when space is the issue.
Does the code allow it?
Recent NEC editions recognize energy management systems that limit load, including for EV charging, and allow a managed load to be counted at the limited value in some cases. We could not load the current NEC text to confirm the exact sections and conditions for this guide, so ask your electrician which provisions your building department accepts. LBNL reported in 2023 that some local code authorities would not allow circuit sharing or smart panel controls. Check with your city before buying a device.
For EV-specific options, see EV charger installation. For batteries, see home battery backup.
What is a smart panel and is it worth it?
A smart panel is a breaker panel with built-in monitoring and remotely controlled circuits. Through an app, you can see what each circuit uses and switch circuits on or off. The feature that matters most for upgrades is dynamic load control: the panel can shed or limit lower-priority loads, such as an EV charger or water heater, when the home nears its service limit, which can avoid a service increase. Smart panels can also extend battery backup by turning off nonessential circuits during an outage.
When a smart panel tends to make sense:
- You need a new panel anyway (old, damaged, flagged brand, or full).
- You are adding an EV charger, heat pump or battery, and the utility side would be expensive to upgrade.
- You want circuit-level energy data or backup control.
When it may not:
- A simple load calculation already shows enough capacity.
- A single circuit-sharing or pausing device solves the problem for much less. LBNL's 2023 figures put smart panels at $3,000 to $5,000 plus installation, versus hundreds of dollars for simpler devices.
- Your building department or utility has not approved the approach.
This guide does not recommend any brand. Ask your electrician whether the product is listed by a nationally recognized testing laboratory, whether your inspector has approved it before, how it behaves if its software or Wi-Fi fails, and whether replacement breakers and support will be available.
How much does it cost to upgrade a panel from 100 to 200 amps?
There is no single price because the job varies so much. Below are the only dated, named studies we found. They are national, and LBNL's respondents clustered on the West Coast and East Coast, with New York and California the most represented states. Treat them as a reality check, not a Texas or Florida quote.
LBNL survey, August 2026 (single-family homes)
| Item | Median | Middle half of answers (IQR) | Mean | Responses |
|---|---|---|---|---|
| Main service panel replacement | $3,500 | $2,100 to $5,000 | $3,931 | 34 |
| Service rating increase: customer-side equipment | $2,800 | $2,000 to $5,000 | $3,409 | 22 |
| Service rating increase: utility-side costs passed to the customer | $3,500 | $1,650 to $7,000 | $5,040 | 19 |
| Subpanel replacement | $1,500 | $775 to $2,500 | $1,879 | 31 |
| Rewiring hazardous or undersized conductors | $5,000 | $1,000 to $7,500 | $7,021 | 21 |
| Panel replacement permit fee (building departments) | Most residential electrical permit categories clustered near a $100 median, with wide variation between jurisdictions |
What this means in plain terms: a 100-to-200-amp upgrade that needs both a new panel and a service increase can cost the panel job plus customer-side service equipment, and in some cases utility-side charges on top. LBNL found utility-side costs were the least predictable, because they jump when added load triggers a transformer or line upgrade.
Utility help with those costs was rare. Nearly all utility staff who answered LBNL's allowance questions (11 of 12 for service rating increases) reported no utility allowance. Some utilities cover costs for certain customers or spread them across all ratepayers. Ask your utility before you sign.
LBNL presentation for ENERGY STAR, 2023
- New circuits: $250 to $750 each.
- Panel: $1,000 to $5,000.
- Service: $1,000 to $25,000 to the homeowner, plus a similar amount for the utility.
- If the upgrade triggers knob-and-tube rewiring: another $10,000 to $30,000.
What drives your price up or down
- Service increase or not. Replacing a panel at the same rating is the simplest job.
- Meter base and riser. If they must be replaced, cost rises. In Florida, these are customer-owned at FPL, TECO and JEA.
- Overhead vs underground. Underground service changes can require trenching and conduit. Oncor says converting existing overhead service to underground, or rerouting existing underground service, is at the customer's cost and needs a project manager's review before an estimate.
- Relocation. Moving the panel or meter adds wire, wall repair and sometimes utility work.
- Code upgrades triggered by the work, such as surge protection, an outdoor emergency disconnect, grounding and bonding, or AFCI protection on modified circuits (explained below).
- Wall, stucco and drywall repair, which some quotes leave out.
- Permit and inspection fees, usually a small share of the total according to LBNL.
- Smart panel vs standard panel.
Get at least two written quotes that spell out each item. See comparing electrical quotes and the electrician cost guide.
How long does a panel upgrade take?
Two different clocks matter: the calendar time from first call to final inspection, and the power-off time on the day of the swap.
Calendar time
LBNL's August 2026 survey of building industry professionals found that for single-family homes:
- Without a service rating increase: 70% of projects were completed within 30 days (26% in 7 days or less, 22% in 8 to 14 days, 22% in 15 to 30 days).
- With a service rating increase: 64% were completed within 30 days (18%, 24% and 22% in the same bands). Utility staff reported 80% within 30 days.
So most single-family jobs finish within a month, but about a third take longer. LBNL's 2023 ENERGY STAR presentation warned that service upgrades can bring 3- to 6-month project delays and that transformer lead times had exceeded a year. Ask your utility early if your upgrade may need a bigger transformer.
Power-off time
For a straightforward panel swap, the power is typically off for most of a working day while the electrician moves circuits to the new panel. A service upgrade that needs the utility to disconnect and reconnect at the meter or pole adds coordination. The final reconnect may wait for the city or county inspection. Ask your electrician for a schedule that shows when power goes off and the latest time it is expected back.
Before the power goes off
- Plan for the refrigerator and freezer. Keep doors closed.
- Arrange backup for medical equipment. See medical equipment backup.
- Charge phones and laptops.
- If you will run a portable generator, keep it outdoors and far from windows, doors and vents, and never connect it to house wiring. CPSC says backfeeding can electrocute utility workers and neighbors.
- Unplug sensitive electronics.
- In summer, plan for heat. In Texas and Florida, a full day without AC is a health issue for some people.
Does the utility have to be involved?
For a panel replacement at the same rating, the utility may only need to disconnect and reconnect service, or nothing at all if the electrician can safely de-energize at a separate outdoor disconnect. For a service upgrade, the utility is always involved, because the meter, and sometimes the service drop or transformer, must match the new rating.
Texas
- Oncor: Oncor handles temporary disconnects and reconnects through 888-313-6862, and notes your retail provider may ask you to place some requests through them. New service, relocating service, and overhead-to-underground conversions go through Oncor's New Construction department at 888-222-8045, where a project manager reviews the job. Oncor's FAQ says customer-requested conversions are at the customer's cost.
- CenterPoint (Houston): We could not load CenterPoint's service-upgrade pages for this guide. Your electrician will usually start the request. Ask CenterPoint about lead times.
- Austin Energy: Austin Energy's contractor resources include electric service planning applications, meter and service wire charges, meter review, and spot location and conduit inspection. Expect the meter location and service path to be reviewed.
- CPS Energy: CPS's guidance on customer-owned equipment repairs says to hire a qualified electrician and obtain a local city permit, and that CPS works with the customer and electrician until service is re-energized.
Florida
FPL, Duke Energy Florida, TECO and JEA all own the meter, and the homeowner owns the meter box and riser. FPL's guidance says it connects service only after customer-owned equipment is repaired and passes any required inspection. For upgrades, your electrician will usually coordinate with the utility, but call the utility yourself early if you suspect the service drop or transformer must change.
Never touch the meter
The meter is utility property in every Texas and Florida utility we checked. Do not remove it, and do not let anyone who is not authorized by the utility remove it. The socket behind it stays energized.
Do I need a permit for a panel upgrade in Texas or Florida?
Yes, in virtually every city and county. Panel and service work is regulated electrical work.
Texas
- State code: Texas adopted the 2026 NEC as its state electrical code effective September 1, 2026 (16 TAC 73.100), with an amendment so GFCI is not required on outdoor dwelling HVAC outlets. TDLR says all non-exempt electrical work statewide, inside or outside city limits, must meet the 2026 NEC.
- Who may do it: TDLR says non-exempt electrical work must be done by licensed individuals working through a licensed electrical contractor. The owner-occupant exemption covers only work not regulated by a city ordinance (Tex. Occ. Code 1305.003(a)(6)). Cities do regulate service and panel work.
- Who inspects: TDLR says local licensing or inspecting authorities, not TDLR, perform the inspections required for local permits.
- Houston: The Houston Permitting Center requires electrical permits for meter and loop service and for installing or rewiring circuit breakers. All permitted work must be inspected and approved by a city electrical inspector, the licensed contractor schedules inspections (online or through the IVR at 713-222-9922), and Houston requires master electricians and contractors to register their state licenses with the city. Houston says permit applications submitted on or after September 1, 2026 are reviewed under the 2026 NEC.
- Austin: Austin's building technical codes table lists the NEC at the 2023 edition with a note that the 2026 edition is effective September 1, 2026.
- Dallas and San Antonio: We could not load their code-adoption pages. Under TDLR's position, the 2026 NEC applies statewide. Confirm local amendments with Dallas Building Inspection and San Antonio Development Services.
- Unincorporated areas: A state license is still required. TDLR says that where no permit is required, the code in effect on the day installation begins applies.
- Fees: Cities may not charge state-licensed electricians a separate registration or license fee for working in the city, but may still charge building permit fees (Tex. Occ. Code 1305.201(f)).
Florida
- Permit law: Section 553.79 makes it unlawful to alter or repair a building without a permit. Its new exemption for work under $7,500 does not apply to electrical work on property with a single-family home.
- Code edition: The 8th Edition Florida Building Code uses the 2020 NEC. The 9th Edition, based on the 2023 NEC, takes effect December 31, 2026 according to the Florida Building Commission. The City of Tampa says January 1, 2027, and that permit applications accepted by December 31, 2026 can proceed under the 8th Edition. Ask your building department which edition applies to your application date.
- Who may do it: A certified (EC) or registered (ER) electrical contractor, or an owner-builder doing the work personally on their own single-family home or duplex for their own use (s. 489.503(6)). The owner-builder must personally sign the permit application and receive a disclosure statement.
- Bonds: Local governments may require one bond per electrical contractor of up to $5,000, conditioned on Florida Building Code compliance (s. 489.537(3)).
- Notice of commencement: If the contract exceeds $5,000, Florida requires a recorded notice of commencement to be filed with the permit office before the first inspection (s. 713.135). A notice of commencement is void if work does not start within 90 days of recording (s. 713.13).
See Texas permits, Florida permits and NEC adoption in Texas and Florida.
Code upgrades a new panel or service can trigger
Replacing service equipment often brings parts of the home up to current code. That is a safety benefit, but it is also why two quotes can differ. Ask each electrician which of these they included.
| Requirement | What it is | When it applies |
|---|---|---|
| Whole-house surge protection (NEC 230.67) | A Type 1 or Type 2 surge-protective device in or next to the service equipment | Since the 2020 NEC, for services supplying dwelling units, including where service equipment is replaced. Mike Holt notes it was driven by sensitive electronics, including AFCIs, GFCIs and smoke alarms that surges can damage. |
| Outdoor emergency disconnect (NEC 230.85) | A readily accessible outdoor disconnect, marked as an emergency disconnect, so responders can cut power | Since the 2020 NEC, for one- and two-family dwelling services. IAEI explains options include an outdoor service disconnect or an outdoor switch ahead of the service equipment, with a permanent, non-handwritten label. |
| AFCI protection for modified circuits (NEC 210.12) | Arc-fault protection when branch circuits are extended or modified | Required in the listed dwelling areas when circuits are modified, with an exception for extensions of not more than 6 feet with no added outlets. The 2020 NEC added guest rooms and suites. |
| GFCI protection | Ground-fault protection in listed locations | Locations expanded in 2020 and 2023. Texas exempts outdoor dwelling HVAC outlets from 210.8(F) under its 2026 adoption. |
| Grounding and bonding | Ground rods or other electrodes, bonding to metal water and gas piping | Brought up to code at the service |
| Working space (NEC 110.26) | Clear space in front of the panel for safe work | New panels must meet working-space rules, which can force relocation |
| Labeling | Circuit directory and required markings | Every new panel |
Want more on surge protection? See whole-house surge protection. On GFCI and AFCI rules, see GFCI and AFCI requirements.
Why did my electrician say I need to move the panel?
Common reasons a new panel cannot go back in the same spot:
- Working space. The NEC requires clear working space in front of panels (Section 110.26). Panels squeezed into closets, behind water heaters, over washing machines, in bathrooms or in tight cabinets often do not meet current rules. The exact dimensions depend on the voltage and code edition, so ask the electrician to show you the rule they are applying.
- Outdoor emergency disconnect. If the main disconnect is indoors, the electrician may move it outside as a meter-main to meet 230.85.
- Utility meter location rules. Utilities set requirements for where meters go so they can be read and serviced. Austin Energy, for example, reviews meter location and conduit before service.
- Flood elevation. In flood-prone parts of Florida and the Texas coast, the building department may require service equipment above a certain elevation for substantial improvements. Ask your building department; this varies by flood zone and local ordinance.
- Damage or corrosion at the current location.
Relocation adds cost because circuits must be extended to the new location, and extending circuits can trigger AFCI requirements. Ask for a quote with and without relocation, and the code reason for each.
Should I go to 400 amp service?
Most single-family homes do not need 400-amp service. It makes sense for very large all-electric homes, homes with multiple EV chargers, large pool and spa equipment, big workshops, or extensive heat and cooling loads, especially when a load calculation shows more than 200 amps of demand.
Costs rise sharply at higher ratings. Utility-side work, especially transformer changes, drives the unpredictability. LBNL found utility-side costs were threshold-driven, jumping when added load exceeds existing transformer capacity. In one California program LBNL cited, the most common panel replacements during heat pump upgrades went from 200 to 300 amps, not 400.
Before you choose 400 amps, ask for a load calculation, consider load management, and ask your utility what it will require and charge on its side.
Florida wind, water and salt: outdoor panel and meter base considerations
Florida's storms put extra stress on outdoor service equipment, and Texas's Gulf Coast faces the same issues.
- The customer owns most of what storms break. FPL, TECO and JEA say the weatherhead, riser and meter box are the customer's responsibility. Oncor, Austin Energy and CPS Energy draw the line similarly in Texas. If your upgrade replaces the meter base, consider having the riser, weatherhead and attachment point replaced and properly secured at the same time.
- Salt corrodes. NEMA's 2026 guide says salt water residue is corrosive and conductive. Coastal homes benefit from equipment rated for outdoor and corrosive environments and from regular checks for rust at the meter base and outdoor disconnect.
- Flooded equipment must be replaced. NEMA says molded-case breakers, GFCIs, AFCIs, surge protectors and wiring devices exposed to water should be replaced, not reconditioned. Panelboards may be reconditioned only after consulting the manufacturer.
- Labels must survive. IAEI notes the outdoor emergency disconnect label must be suitable for its environment, including corrosive coastal air.
- Product approvals. Miami-Dade and Broward have strict product approval rules for building envelope items. We could not confirm whether those approvals apply to electrical panels, so ask your building department rather than assuming.
See hurricane electrical safety and flood-damaged electrical.
Upgrading for an EV charger, heat pump, solar or battery
New electric loads are the most common reason homeowners ask about upgrades today. Each has its own wrinkle.
EV chargers
The U.S. Department of Energy's Alternative Fuels Data Center says many EV drivers can meet their daily needs by charging overnight with Level 1 equipment, which uses a standard outlet on a dedicated branch circuit. Level 2 charging uses 240 volts for faster charging. DOE notes that some homes may lack capacity for Level 2 equipment, that a qualified electrician can add circuits for it, that the NEC treats EV charging as a continuous load (Article 625), and that permits may be required. LBNL's 2023 presentation pointed out that limiting an EV charger to about 7.2 kW fully recharges most EVs overnight and can avoid a service upgrade, and that timers, circuit sharing and meter collars are other options. See EV charger installation.
Heat pumps
Data LBNL cited suggest heat pumps alone drive fewer panel upgrades than people expect. A Vermont study of about 10,000 homes found the average added demand was about 200 watts, and LBNL suggested avoiding backup resistance heat and deep thermostat setbacks to keep peaks down. Texas and Florida heat pumps often include electric heat strips, which are a large load, so include them in the load calculation. See HVAC electrical.
Solar
Solar affects the panel in two ways. First, the panel's bus and main breaker must be able to accept the solar connection. Second, as Miami-Dade's 2020 NEC summary notes, a home with solar cannot use the 220.87 measured-load method because actual maximum demand cannot be measured. On the utility side, Oncor says you may install a system at any time but may not operate it until the interconnection agreement is complete and Oncor issues permission to operate, and that customers pay for distribution upgrades, such as a bigger transformer, needed to support their system. See solar interconnection.
Batteries and generators
A home battery or standby generator usually needs a transfer switch or a backup panel. Planning these at the same time as a panel replacement can save a second round of work. Never connect a portable generator to house wiring without a transfer switch or interlock. See home battery backup and standby generators.
Would a subpanel solve my problem instead?
If the issue is space, not capacity, a subpanel may be enough. A subpanel is a second, smaller panel fed from the main panel. It adds breaker spaces where you need them, such as in a garage, workshop or addition. LBNL's August 2026 survey found a median single-family subpanel replacement cost of $1,500 (middle half $775 to $2,500), well below the main-panel figure.
A subpanel does not add capacity. The total load is still limited by your service and main breaker. Tandem breakers, which fit two circuits in one space, can also help where the panel's listing allows them. Your electrician should confirm with a load calculation that the service can support what the subpanel will feed. See subpanels for garages and additions.
Older homes: what else the electrician may find
Opening up an old panel sometimes reveals problems that change the scope.
- Aluminum branch wiring. CPSC says homes built before 1965 are unlikely to have aluminum branch wiring, but cables installed between 1965 and the mid-1970s may. CPSC's recognized permanent repairs are rewiring with copper or pigtailing each connection with the COPALUM crimp method, or AlumiConn as an alternative. Florida's Citizens requires separate documentation, certified by a licensed electrician, of any single-strand aluminum wiring remediation. See aluminum wiring.
- Knob-and-tube or cloth-insulated wiring. Citizens' 4-point form flags active knob and tube and cloth wiring. LBNL's 2023 presentation estimated knob-and-tube replacement at another $10,000 to $30,000 when an upgrade triggers it. See knob and tube wiring.
- Undersized or damaged conductors. LBNL's 2026 survey found a median single-family cost of $5,000 for rewiring hazardous or undersized conductors, with a very wide range.
- Missing grounding, or two-prong circuits. See ungrounded outlets.
- Old unpermitted work, such as double-tapped breakers or splices inside the panel.
Ask the electrician to tell you before work starts how they will price surprises, and to show you photos of anything that changes the scope.
Questions to ask before you sign
- Is this a panel replacement, a service upgrade, or both? What amperage, and why?
- Can I see the load calculation? Which NEC method did you use?
- Would a load-management device or smart panel avoid a service upgrade here?
- Does the price include the meter base, riser and weatherhead, if needed?
- Does it include whole-house surge protection and an outdoor emergency disconnect?
- Will the panel move? If so, why, and what does that add?
- Who pulls the permit and schedules the inspection? Is the permit fee included?
- Who coordinates with the utility, and are any utility charges expected?
- How long will the power be off, and what happens if the inspection is delayed?
- What wall, stucco or drywall repair is included?
- What is your warranty on labor and materials?
- What are your state license numbers? (TDLR in Texas, DBPR in Florida.)
Step by step: how a panel or service upgrade usually goes
- Assessment. The electrician inspects the panel, meter base, service entrance, grounding and the loads you plan to add.
- Load calculation. Ask which NEC method was used and see the numbers.
- Options and written quote. Panel only, service upgrade, or load management. The quote should list the panel rating, meter base, surge protection, outdoor disconnect, grounding, permit, inspection, wall repair and any utility charges.
- Contract. Texas homestead lien rules require a written contract signed before work begins (and by both spouses if married) for a contractor to fix a lien on a homestead, and the contractor must give the statutory disclosure statement before signing (Tex. Prop. Code 53.254, 53.255). In Florida, a direct contract over $2,500 on a 1-4 unit home must include the statutory construction lien notice (s. 713.015).
- Permit. The contractor (or Florida owner-builder) pulls the permit. Florida: a notice of commencement for contracts over $5,000.
- Utility coordination. The electrician or homeowner requests the disconnect, meter work or service change.
- Installation day. Power off, old panel removed, new panel and service equipment installed, circuits moved and labeled.
- Inspection. The city or county inspector checks the work. Some jurisdictions inspect before the utility reconnects.
- Reconnect. The utility energizes the new service and sets the meter.
- Closeout. Keep the permit, the final inspection record, the load calculation and the panel directory. Florida homeowners will need panel age and brand for future 4-point inspections.
What brand of panel should I choose?
This guide does not rank or endorse brands. Several major manufacturers make listed residential panels. A better question is what to look for:
- Listing by a nationally recognized testing laboratory, and breakers listed for that panel.
- Breaker availability locally, including AFCI, GFCI and dual-function types, so future repairs are not delayed.
- Enough spaces for planned loads, with room to spare.
- Surge protection options that fit the panel.
- Outdoor and corrosion ratings for exterior equipment, especially on the coast.
- Your electrician's familiarity and the local inspector's experience with the product.
For smart panels, also ask how the panel behaves without internet, whether it is approved by your building department, and how long the maker supports its software.
Does a panel upgrade increase home value?
We did not find a reliable, dated study measuring how much a panel upgrade adds to sale price in Texas or Florida, so we will not give a number. What is clear:
- Insurability. In Florida, an old, undersized or flagged panel can complicate a 4-point inspection and an insurance application, which can affect a sale. Citizens' form records panel age, brand, amperage and whether it is sufficient.
- Buyer inspections. Home inspectors commonly note fuse boxes, flagged brands, double taps and damage. Fixing them before listing removes a negotiating point. See electrical inspections when buying or selling.
- Capacity for EVs and electrification. A home ready for an EV charger or heat pump may appeal to some buyers.
Keep the permit and final inspection records. Unpermitted panel work can raise questions during a sale.
Hiring the right electrician for a panel upgrade
- Texas: Verify the contractor and master electrician on TDLR's license search, or call 800-803-9202. TDLR requires electrical contractors to carry business liability insurance of at least $300,000 per occurrence, $600,000 aggregate, and $300,000 aggregate for products and completed operations, and contractors must display their business name and license number on both sides of their vehicles. In Houston, the contractor must also be registered with the city.
- Florida: Verify the license with DBPR. A certified electrical contractor (EC) may work statewide; a registered contractor (ER) only where registered. Local governments may refuse permits to contractors with certain disciplinary histories (s. 489.537(3)(e)).
- Ask who pulls the permit, who schedules the inspection, and who coordinates with the utility.
- Ask for the load calculation in writing.
- Ask how they handle wall and stucco patching.
- Get a warranty in writing. See electrical warranties.
More in the hiring checklist, Texas licensing and Florida licensing.
How to choose a provider
- Decide which job you need: panel only, service upgrade, or load management.
- Ask for a written NEC load calculation and which method (220.83 or 220.87) was used.
- In Texas, ask whether your smart-meter interval data can support a measured-load calculation.
- Price load-management options (circuit sharing, pausing, smart panel) before a service increase.
- Call your utility early to ask about utility-side charges and transformer lead times.
- Get at least two itemized quotes listing meter base, surge protection, outdoor disconnect, grounding, permit, inspection and wall repair.
- Verify the license: TDLR in Texas, DBPR in Florida.
- Sign a written contract; in Texas homestead work, both spouses sign before work starts.
- In Florida, file a notice of commencement if the contract exceeds $5,000.
- Plan for a day without power: food, medical equipment, heat, generator safety.
- Keep the permit, final inspection, load calculation and panel directory for insurance and resale.
Related electricians guides
- Federal Pacific, Zinsco and Challenger Panels: Are They Dangerous and Will Insurers Cover You?
- How Do You Install a Home EV Charger? Circuits, Panels, Permits, GFCI Rules and Cost in Texas and Florida
- Whole-House Surge Protectors: Do They Work, Which Type, and What Do They Cost?
- Meter, Meter Base, Service Drop: What Does the Utility Fix and What Do You Pay For?
- Do You Need an Electrical Permit in Texas, and Can a Homeowner Do the Work?
- Florida Electrical Permits: Owner-Builder Rules, Exemptions, Open Permits and Inspections
- Subpanels for Garages, Workshops, ADUs and Additions: When You Need One, What It Costs and What Code Requires
- Florida 4-Point Inspection: What the Electrical Section Checks and How to Fix What It Flags
Electricians by state and city
Questions people ask
How much does it cost to upgrade a panel from 100 to 200 amps?
The best dated national data, LBNL's August 2026 survey, found a median of $3,500 for a single-family main panel replacement and a median of $2,800 for customer-side equipment in a service rating increase, plus a median $3,500 when utility-side costs were passed on. Costs vary widely with meter base replacement, underground service, relocation and code items. Get itemized quotes.
How long does a panel upgrade take?
Most single-family projects in LBNL's 2026 survey finished within 30 days of the request or permit: 70% without a service increase and 64% with one. The power is usually off for most of a working day during the swap, and reconnection may wait for inspection. Projects needing utility transformer work can take months.
Panel replacement vs service upgrade: what's the difference?
A panel replacement swaps the breaker box, usually at the same rating, and leaves the utility service alone. A service upgrade raises the amperage of the whole service, which usually means new service entrance wires, often a new meter base, a new panel, and utility work on the meter and sometimes the service drop or transformer. A service upgrade costs more and takes longer.
Will my power be off during a panel upgrade?
Yes, for part of the job. For a typical panel swap, expect power off for most of a working day while circuits move to the new panel. If the utility must disconnect and reconnect, or the city must inspect before reconnection, the outage can stretch longer. Ask for a schedule, and plan for food, medical devices and heat.
Do I need to upgrade my meter base too?
Often, for a service upgrade. The meter base must be rated for the new service, and older or corroded meter bases are commonly replaced. In Texas and Florida, the meter base is usually customer-owned (Oncor, Austin Energy, FPL, TECO and JEA say so), so it is part of your cost. A meter-main combo replaces the meter base and adds an outdoor main disconnect in one enclosure.
Does the utility have to be involved in a panel upgrade?
For a service upgrade, yes: the meter, and sometimes the drop or transformer, must match the new rating. For a same-size panel replacement, the utility may only need to disconnect and reconnect. In deregulated Texas, the wires company (such as Oncor or CenterPoint) handles this, not your retail provider. Oncor handles disconnects at 888-313-6862 and new or relocated service at 888-222-8045.
What is a load calculation and do I need one?
It is an NEC Article 220 calculation of your home's maximum demand. It shows whether your existing service can handle new loads like an EV charger or heat pump. For existing homes, 220.83 uses connected loads with demand factors, and 220.87 uses your actual measured peak times 1.25 plus the new load. Ask for it in writing before agreeing to a service upgrade.
Can I avoid a panel upgrade with a load management device?
Often. Circuit-sharing devices, circuit-pausing relays and smart panels can keep total demand under your service rating. LBNL's 2023 figures put circuit sharing at $300 to $600, pausing at $400 to $900, and smart panels at $3,000 to $5,000, each plus installation. LBNL also reported that some local code authorities would not allow these controls, so check with your building department first.
Do I need a permit for a panel upgrade in Texas or Florida?
Yes. In Texas, panel and service work must be done by TDLR-licensed electricians through a licensed contractor under the 2026 NEC, with local permits and inspections in cities like Houston. In Florida, s. 553.79 requires permits for electrical work on single-family homes, and the work must be done by a licensed contractor or a qualifying owner-builder. Unpermitted work can cause insurance and resale problems.
Should I go to 400 amp service?
Most single-family homes do not need it. Consider it only when a load calculation shows demand well above 200 amps, such as a very large all-electric home with multiple EV chargers, pool and spa equipment or a big workshop. Utility-side costs rise sharply when added load requires a bigger transformer, and LBNL found those costs were the least predictable part of upgrades. Ask about load management first.
What is a meter-main combo?
It is one outdoor enclosure that holds both the utility meter socket and your main service disconnect, sometimes with breakers too. It is a common way to meet the 2020 NEC rule for an outdoor emergency disconnect at one- and two-family homes, so responders can cut power without pulling the meter. With a meter-main outside, your indoor panel is fed from it as a subpanel.
Does a panel upgrade help with Florida home insurance?
It can. Citizens requires a 4-point inspection for homes over 20 years old, and the form records panel age, brand, amperage and hazards such as double taps, scorching and wrong-size breakers. Citizens tells agents not to submit applications with existing hazards. A newer, properly installed panel with records can make the inspection simpler, though each insurer sets its own rules.
Sources
- LBNL: Understanding the Costs and Barriers of Residential Electrical Panel and Service Upgrades (Aug. 2026)
- ENERGY STAR/LBNL: Reducing the Cost of Electrification with Alternatives to Electric Panel Upgrades (Sept. 2023)
- Miami-Dade: Electrical Changes for the 2020 NEC (8th Edition FBC)
- Mike Holt: 2020 NEC changes, 230.67 Surge Protection
- IAEI Magazine: New 2020 NEC requirement (230.85) helps keep first responders safe
- Mike Holt: 2023 NEC changes, 210.12 AFCI
- TDLR: Commission adopts 2026 NEC (16 TAC 73.100)
- TDLR: The Texas Circuit, July 2026
- TDLR: Electricians Compliance Guide
- TDLR: Electricians
- TDLR: Electrical Contractor license requirements
- TDLR Electricians FAQ
- Texas Occupations Code ch. 1305
- Texas Property Code ch. 53 (mechanic's liens)
- Houston Permitting Center: Electrical Inspections
- Houston Permitting Center: 2026 NEC effective September 1, 2026
- City of Austin: Building Technical Codes
- Oncor: Outage and service FAQs
- Oncor: Meter FAQs
- Austin Energy: Not All Equipment Belongs to Austin Energy
- CPS Energy: Copper theft and customer equipment repairs
- CPS Energy: Power Quality FAQs
- FPL: Make sure you're ready to safely receive power
- Tampa Electric: Damaged Meter Equipment
- JEA: Damaged Weatherheads
- KPRC Click2Houston: Electrical meter box is down, who's responsible? (2024)
- Florida Statutes s. 553.79 (permits)
- Florida Statutes s. 489.503 (exemptions)
- Florida Statutes s. 489.537
- Florida Statutes s. 713.015
- Florida Statutes s. 713.13
- Florida Statutes s. 713.135
- Florida Building Commission 9th Edition course text
- City of Tampa: 9th Edition FBC announcement
- DBPR: Electrical Contractors
- Citizens 4-Point Inspection Form Insp4pt 03 25 (sample copy)
- Citizens Property Insurance: Inspections
- TDI: Rule on home and roof age (Sept. 2026)
- NEMA CS 70006-2026, Evaluating Water-Damaged Electrical Equipment
- CPSC Portable Generator Safety Alert
- DOE Alternative Fuels Data Center: Charging Plug-In Electric Vehicles at Home
- CPSC: Repairing Aluminum Wiring, Pub. 516
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


