Local Guide · Electricians
Knob-and-Tube and Cloth Wiring: Is It Safe, Can You Insure It, and What Are Your Rewiring Options?
How to tell knob-and-tube from cloth-jacketed cable, why insulation and missing grounds matter, how Florida 4-points and Texas insurance rules treat it, and how to plan a full or phased rewire in a historic home.
Knob-and-tube is early wiring of separate single wires on porcelain knobs and tubes, with no ground wire. Any that remains is many decades old. Risks include brittle insulation, unsafe add-on splices, over-fusing, and overheating if buried in insulation, which the NEC has barred since 1987. Florida 4-point forms flag active knob-and-tube and cloth wiring. In Texas, insurers may act on its condition but not its age alone.
Key facts
- IAEI: knob-and-tube has no equipment grounding conductor.
- Since the 1987 NEC, knob-and-tube has been barred from cavities where loose, blown-in or foamed-in insulation envelops the conductors (IAEI).
- IAEI: the NEC allows knob-and-tube to be extended from an existing installation, but proper hardware is hard to find.
- The NEC is not, by its own terms, retroactive (IAEI).
- The Citizens 4-point form has separate checkboxes for cloth wiring and active knob and tube.
- Citizens requires a four-point inspection for homes more than 20 years old.
- TDI (Sept. 2026): Texas insurers may base decisions on the physical condition of wiring, but not its age alone.
- LBNL (Aug. 2026): median single-family rewiring cost was $5,000 (IQR $1,000 to $7,500; mean $7,021).
What knob-and-tube wiring is, and what cloth wiring is
Knob-and-tube (often written K&T) is the earliest common wiring method in American homes. Single insulated wires run separately, a few inches apart, through the attic and walls. White porcelain knobs nailed to framing hold the wires in place, and porcelain tubes protect the wires where they pass through joists and studs. Splices were usually soldered and wrapped with tape. It was designed to shed heat into open air.
Cloth-insulated wiring is a broader term. Knob-and-tube conductors had cloth-covered rubber insulation, but so did later cloth-jacketed cable, where two (and later three) insulated wires were bundled inside a woven cloth outer jacket. That cable looks like an early version of modern plastic-sheathed cable. In many Texas and Florida homes built before modern plastic-sheathed cable became standard, you will find cloth-jacketed cable rather than true knob-and-tube.
The Citizens Property Insurance 4-point form treats them separately. It has a checkbox for "cloth wiring" and another for "active knob and tube," and lists both "cloth (knob and tube)" and "cloth jacket rubber insulated" as wiring types. That distinction matters for insurance, as explained below.
| Knob-and-tube | Cloth-jacketed cable | |
|---|---|---|
| Look | Separate single wires on porcelain knobs, through porcelain tubes | Wires bundled inside a woven cloth jacket |
| Ground wire | None | Often none in older versions |
| Main concern | Age, insulation, splices, buried in insulation, no ground | Brittle rubber insulation, often no ground |
| 4-point form box | "Active knob and tube" | "Cloth wiring" |
Is knob-and-tube wiring safe?
Knob-and-tube that was installed well and has never been disturbed can still carry power. The problem is that it is now many decades old, and few systems have gone untouched. The main risks:
- Aging insulation. The rubber and cloth insulation dries, cracks and flakes, especially where it was exposed to attic heat. Texas and Florida attics get very hot in summer, which speeds this up.
- Buried in insulation. Knob-and-tube depends on open air to cool. Since the 1987 NEC, the wiring method has been barred from wall and ceiling cavities with loose, blown-in or foamed-in-place insulation that envelops the conductors, IAEI Magazine reports. Blowing insulation over it traps heat.
- No ground. IAEI notes knob-and-tube "has no equipment grounding conductor carried with it." That means no grounding path for three-prong outlets and less protection from shock.
- Amateur modifications. Decades of add-ons, splices made without boxes, and connections to newer cable are common sources of trouble.
- Over-fusing. Many knob-and-tube homes also have fuse panels. Oversized fuses let the old wire overheat. See old fuse boxes.
- Modern loads. Window AC units, space heaters and kitchen appliances on circuits designed for a few light bulbs.
The honest answer: a specific system can only be judged by an electrician who looks at it. But insurers, home inspectors and most electricians treat active knob-and-tube as a system near the end of its life.
How do I identify knob-and-tube or cloth wiring?
- Look in the attic (carefully, on framing, with a flashlight, without touching wires). Porcelain knobs on the joists with single wires running between them, or porcelain tubes through framing, are the clearest sign.
- Look in the crawlspace or basement. Raised-floor homes, common in older neighborhoods of Houston, San Antonio, Austin, Tampa and Jacksonville, often show wiring under the floor.
- Look at the panel. Wires entering a fuse box or old panel in fabric-covered cable, or as separate single wires through porcelain bushings, suggest old wiring.
- Look at outlets. Two-prong outlets throughout the house are a clue (though not proof). See ungrounded two-prong outlets.
- Look at the age of the house and past permits. Your city's permit records may show when the home was rewired.
"Active" matters. Many homes have abandoned knob-and-tube left in the attic after a rewire. The Citizens form asks about active knob-and-tube. An electrician can confirm whether old wires are disconnected (dead) or still energized, and document it. Never assume an old wire is dead.
Is it grounded? Can I add three-prong outlets?
No, knob-and-tube is not grounded; it has no equipment grounding conductor. Older cloth-jacketed cable often lacks one as well.
You still have legal options for replacing outlets under the NEC's receptacle replacement rules (406.4(D)), as IAEI explains: replace a two-prong outlet with another two-prong outlet; install a GFCI receptacle marked "No Equipment Ground"; or install three-prong outlets downstream of GFCI protection, each marked "GFCI Protected" and "No Equipment Ground," with no ground wire connected between them. A GFCI protects people from shock but does not create a ground for surge protectors or equipment that needs one.
A separate ground wire can also be retrofitted to a circuit under NEC 250.130(C) in some cases. IAEI notes that until the 1993 NEC, a local bonded water pipe could be used for a ground, but that is no longer permitted that way. Your electrician will apply the edition your city enforces. For full details, see ungrounded outlet fixes.
Can insulation be blown over knob-and-tube?
Not under the NEC since 1987. IAEI reports that since the 1987 edition, knob-and-tube has been barred from cavities with "loose, filled, or foamed-in-place insulating material that envelops the conductors." IAEI notes the rule effectively prevents insulating those cavities and that it has been controversial.
This is a real conflict in Texas and Florida, where adding attic insulation is one of the best ways to cut summer cooling bills. Your practical options:
- Replace the knob-and-tube in the attic first, then insulate.
- Have an electrician confirm that the old attic wiring is fully abandoned (disconnected at both ends) before insulating over it.
- Do not let an insulation crew blow insulation over active knob-and-tube to save money. It traps heat on the wires, and it can cause problems with an insurer later.
Spray foam in walls with active knob-and-tube raises the same issue. Ask the electrician first.
Can I get homeowners insurance with knob-and-tube wiring?
Florida
It is hard. Citizens requires a four-point inspection for homes more than 20 years old, and the form flags "active knob and tube" and "cloth wiring." Citizens tells agents they may not submit applications for homes with electrical systems not in good working order or with existing hazards. Whether a specific carrier will write a home with active knob-and-tube is a carrier decision; ask your agent before closing on a historic home. See the Florida 4-point electrical guide.
Texas
Texas clarified its rule in September 2026: insurers cannot decline or non-renew a home policy because of the age of the house or its components. They may base decisions on the physical condition of components such as wiring. So in Texas, the question is condition, not age. Active knob-and-tube with damaged insulation, buried in insulation, or with unsafe splices is a condition an insurer may act on. A recent electrician evaluation of a sound, unmodified system is your best evidence. Call the TDI Help Line at 800-252-3439 if you think you were turned down only because the wiring is old.
Can a home with knob-and-tube pass inspection?
It depends on which inspection:
- Permit inspection: Existing wiring is not automatically a code violation. IAEI notes that "the NEC is not, by its own terms, retroactive." But new work must meet current code. IAEI also notes the NEC allows knob-and-tube to be extended from an existing installation, but proper hardware is hard to find, and salvaged knobs do not fit today's thinner insulated conductors. In practice, electricians tie new circuits into modern cable, not more knob-and-tube.
- Home inspection for a sale: Expect it to be written up. In Texas, inspectors working under the TREC standards of practice (22 TAC 535.229) must report deficiencies such as missing grounding on 125-volt receptacles, missing GFCI or AFCI protection in required locations, and deficiencies in wiring and terminations.
- Florida 4-point: Active knob-and-tube is recorded and can block a policy.
Partial vs full rewire: what are the options?
| Option | What it involves | Pros | Cons |
|---|---|---|---|
| Full rewire | Replace all old wiring with modern grounded cable; new panel if needed | Solves insurance, grounding and capacity at once | Most cost and wall patching |
| Partial rewire | Replace the worst or most accessible circuits (attic, kitchen, baths) first | Spreads cost; tackles highest risk first | Insurers may want all active knob-and-tube gone |
| Abandon in place | New circuits run; old wires disconnected at both ends and left in walls | Less demolition | Must be clearly documented as dead |
| Interim safety steps | Correct fuse sizing, add GFCI protection, remove insulation from around active wires, fix bad splices | Low cost, reduces risk now | Does not remove the old wiring or settle insurance |
For insurance in Florida, partial work often is not enough if any knob-and-tube remains active. Ask your agent what the carrier requires before you choose. Get the electrician to document every circuit replaced and confirm which old wiring is dead.
Cost
The only dated, primary cost study we found is the Lawrence Berkeley National Laboratory's August 2026 national survey. It reported a median per-home rewiring cost (replacing hazardous or undersized conductors) of $5,000 for single-family homes, with an interquartile range of $1,000 to $7,500 and a mean of $7,021. LBNL says rewiring costs varied with project-specific conditions and the extent of partial versus full replacement. A full rewire of a large plaster-walled historic home can cost well above that range. See house rewiring cost.
Historic homes in Texas and Florida: local notes
Knob-and-tube and cloth wiring cluster in the oldest neighborhoods of our eight largest cities. Examples include the Houston Heights, Hyde Park in Austin, King William in San Antonio, Swiss Avenue in Dallas, older Miami neighborhoods, Hyde Park in Tampa, Riverside in Jacksonville, and older parts of St. Petersburg and Orlando.
- Historic district rules. Many of these areas are locally designated historic districts with design review. Interior rewiring is usually an interior project, but exterior changes, such as moving the meter, adding a new mast, a new service location or exterior conduit on a street-facing wall, may need review. Ask your city's historic preservation office before the electrician designs the service.
- Plaster and lath walls. Older homes often have plaster walls, which are harder to fish wire through and to patch. Experienced old-house electricians route through attics, crawlspaces and closets to limit wall openings.
- Raised floors help. Pier-and-beam homes, common in older Texas neighborhoods, and raised wood-frame homes in Florida let electricians run new wiring from below.
- Permits. Houston requires an electrical permit for new circuits, rewired breakers and rewired fixtures, other Texas cities have similar rules, and Florida's s. 553.79 requires a permit to alter or repair a building where the code calls for one. In Texas, state-licensed electricians may not be charged extra city registration fees, but the city can charge building permit fees (Occupations Code 1305.201(f)).
See electrical in older homes and the city guides for Houston, Austin, San Antonio, Dallas, Miami, Tampa and Jacksonville.
Is BX or old armored cable a problem?
BX is a common name for early armored cable: insulated wires inside a spiral metal sheath. It shows up in older homes, sometimes alongside cloth wiring. The Citizens 4-point form groups "NM, BX or conduit" together as a wiring type, which suggests BX by itself is not treated like knob-and-tube.
Two issues to have an electrician check:
- Grounding. Very old armored cable may not have a ground wire or a bonding strip, so the metal sheath may not be a reliable ground path. A plug-in tester may show a ground that is not dependable.
- Insulation inside. Older BX often has cloth-and-rubber insulated wires inside the armor, which can be brittle at the ends where they enter boxes.
If the electrician finds the sheath is not a reliable ground, treat those outlets like ungrounded outlets and use one of the NEC replacement options.
Living with knob-and-tube until you rewire
- Have a licensed electrician evaluate it and confirm fuse or breaker sizes match the wire.
- Do not overload circuits with space heaters, window AC units or kitchen appliances.
- Keep stored items away from attic wiring and never cover it with insulation.
- Add GFCI protection in kitchens, baths, laundry and outdoors (an electrician can do this without a ground, using the NEC's marked options).
- Test smoke alarms monthly.
- Watch for warm switch plates, flickering lights, buzzing or burning smells, and call an electrician if you notice them.
- Plan the rewire before you need insurance in a hurry, such as at sale or renewal.
Questions to ask an electrician before you rewire an old house
- Is any knob-and-tube or cloth wiring still active, and on which circuits? Will you put that in writing?
- Do you recommend a full or phased rewire for this house, and why?
- How will you route new wiring: attic, crawlspace, closets, or through finished walls?
- How many wall and ceiling openings do you expect, and who patches them? Is plaster repair included?
- Will the existing panel or fuse box handle the new circuits, or does it need replacing? If it is replaced, the current NEC requires a surge-protective device at the service.
- Will you pull the permit and schedule the inspections, and how long do you expect them to take?
- What happens to abandoned wiring: removed, or disconnected at both ends and left in place?
- Will you provide a letter my insurer will accept, listing what was replaced and when?
- What is your Texas TDLR or Florida DBPR license number, and who is the master electrician or qualifier on the job?
Verify the answer to the last question yourself on the TDLR license search or DBPR license lookup before you sign.
How to choose a provider
- Look for porcelain knobs and tubes in the attic or crawlspace with a flashlight, without touching wires.
- Have a licensed electrician confirm whether old wiring is active or abandoned, and document it.
- Check that fuses or breakers match the wire size; fix any over-fusing.
- Remove insulation that envelops active knob-and-tube or replace those circuits before insulating.
- Ask your insurance agent what the carrier requires before buying or renewing.
- Get quotes for a full rewire and a phased partial rewire.
- Check historic district rules before moving the meter or service.
- Make sure the rewire is permitted and inspected.
- Keep the electrician's documentation for 4-point inspections and future buyers.
Related electricians guides
- How Much Does It Cost to Rewire a House? Real Cost Data, the Process, Timeline and Living Through It
- Two-Prong Ungrounded Outlets: Are They Legal, Are They Safe, and What Are the Real Fixes?
- Old Fuse Box: Is It Safe, Can You Insure It, and What Does Replacing It Cost?
- Aluminum Wiring: How Dangerous Is It, Which Fixes Work (COPALUM, AlumiConn) and What Do Texas and Florida Insurers Require?
- Florida 4-Point Inspection: What the Electrical Section Checks and How to Fix What It Flags
- Electrical in Older Homes (Pre-1980): What to Expect and What to Upgrade First in Texas and Florida
- Electrical Inspections When Buying or Selling a Home in Texas or Florida: What Gets Flagged and What to Fix
Electricians by state and city
Questions people ask
Is knob and tube wiring safe?
It depends on condition, but every system still in use is many decades old. Risks include brittle insulation, no ground wire, unsafe add-on splices, over-fusing, and overheating when buried in insulation, which the NEC has barred since 1987. A licensed electrician must evaluate the specific system. Insurers and inspectors generally treat active knob-and-tube as near the end of its life.
Is cloth-insulated wiring the same as knob and tube?
Not always. Knob-and-tube conductors have cloth-covered insulation, but so does later cloth-jacketed cable, where wires are bundled inside a woven jacket. The Citizens 4-point form has separate boxes for cloth wiring and active knob and tube, and lists cloth jacket rubber insulated as its own wiring type. Both often lack a ground wire.
Can I get homeowners insurance with knob and tube wiring?
In Florida it is difficult, because the Citizens 4-point form flags active knob and tube and Citizens agents may not submit homes with existing electrical hazards. In Texas, TDI says insurers cannot decline based on the age of wiring alone, only its physical condition. Ask your agent before buying, and get an electrician's written evaluation.
How much does it cost to replace knob and tube wiring?
LBNL's August 2026 national survey found a median single-family rewiring cost of $5,000, with a middle range of $1,000 to $7,500 and a mean of $7,021. Costs vary with how much wiring is replaced, wall type, attic and crawlspace access, and whether a panel upgrade is included. Plaster-walled historic homes can cost more. Get several written quotes.
Can I partially replace knob and tube?
Yes. Many owners replace attic circuits and high-load rooms first. The NEC also allows knob-and-tube to be extended from an existing installation, though matching hardware is hard to find. For Florida insurance, partial work may not be enough if any knob-and-tube remains active, so ask the carrier what it requires before choosing a phased plan.
Can insulation be blown over knob and tube?
No. Since the 1987 NEC, knob-and-tube has been barred from cavities where loose, blown-in or foamed-in insulation envelops the conductors, according to IAEI. The wiring needs open air to shed heat. Replace or fully disconnect the attic wiring before adding insulation, and have an electrician confirm it is dead.
Is knob and tube grounded?
No. IAEI notes knob-and-tube has no equipment grounding conductor. You can replace its two-prong outlets with two-prong outlets, with a GFCI marked No Equipment Ground, or with three-prong outlets protected by a GFCI and marked GFCI Protected and No Equipment Ground. A GFCI protects people but does not create a ground for surge protectors.
Do historic districts restrict rewiring?
Interior rewiring is usually an interior matter, but exterior changes, such as a new meter location, mast or exterior conduit, may need design review in a local historic district like the Houston Heights or King William. Ask your city's historic preservation office before the electrician designs the new service. The electrical permit is separate.
Sources
- IAEI Magazine: Inspecting Electrical Renovations
- IAEI Magazine: Article 406, Receptacles (replacement rules)
- Citizens Property Insurance: Inspections
- Citizens 4-Point Inspection Form Insp4pt 03 25 (sample, third-party hosted copy)
- TDI news release (Sept. 29, 2026): age-of-home underwriting rule
- 22 TAC 535.229, TREC Standards of Practice: Electrical Systems (LII copy)
- LBNL (Aug. 2026): Costs and Barriers of Residential Panel and Service Upgrades
- Florida Statutes s. 553.79 (permits)
- Texas Occupations Code ch. 1305
- Houston Permitting Center: Electrical Inspections
- Mike Holt: 2020 NEC 230.67 Surge Protection
- TDLR License Search
- DBPR Electrical Contractors' Licensing Board
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


