New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Electricians

How Much Does It Cost to Rewire a House? Real Cost Data, the Process, Timeline and Living Through It

Dated cost data from LBNL's 2026 survey, what a full rewire includes, permits and inspections, how slab homes in Texas and concrete block homes in Florida change the method, and how to live through the work.

The best dated data, Lawrence Berkeley National Laboratory's August 2026 national survey, found a median rewiring cost of $5,000 per single-family home, with a middle range of $1,000 to $7,500 and a mean of $7,021. That covers partial and full jobs, so large or plaster-walled homes can cost more. Rewiring needs a permit, rough-in and final inspections. Texas slab homes route wiring through the attic; Florida concrete block walls may need chases or surface raceway.

Key facts

  • LBNL (Aug. 2026): median single-family rewiring cost $5,000; IQR $1,000 to $7,500; mean $7,021; 21 responses.
  • LBNL (Aug. 2026): median home rewiring permit fee $129 (IQR $61 to $250).
  • LBNL (Aug. 2026): median single-family main panel replacement $3,500 (IQR $2,100 to $5,000).
  • LBNL/ENERGY STAR (2023): typical $250 to $750 per new circuit.
  • 2023 NEC 210.12(B) requires AFCI protection on 15A and 20A, 120V circuits in most dwelling living areas, bedrooms and kitchens.
  • NEC 230.67 requires surge protection where service equipment is replaced.
  • Houston: all work requiring an electrical permit must be done by a licensed electrical contractor and inspected.
  • Texas uses the 2026 NEC (Sept. 1, 2026); Florida uses the 2020 NEC until the 9th Edition FBC (2023 NEC) takes effect Dec. 31, 2026 (state) or Jan. 1, 2027 (Tampa).

How much does it cost to rewire a house?

Most cost figures you see online for rewiring are not tied to any study. The best dated, primary source we found is the Lawrence Berkeley National Laboratory (LBNL) survey published in August 2026, Understanding the Costs and Barriers of Residential Electrical Panel and Service Upgrades. It surveyed 140 building industry, utility and building department respondents across 34 states. Its findings for rewiring, defined as "replacing hazardous or undersized conductors":

LBNL 2026 survey itemMedianMiddle 50% (IQR)MeanResponses
Rewiring, single-family home (per home)$5,000$1,000 to $7,500$7,02121
Rewiring, small multifamily (2 to 4 units, per home)$1,500$1,000 to $3,000$2,34010
Main service panel replacement, single-family$3,500$2,100 to $5,000$3,93134
Subpanel replacement, single-family$1,500$775 to $2,500$1,87931
Home rewiring permit fee (building departments)$129$61 to $250$18333 departments (all categories)

Read these numbers carefully:

  • The range is wide. "Rewiring" in the survey includes partial jobs, such as replacing a few hazardous circuits, as well as whole-house rewires. LBNL says rewiring costs showed no clear relationship with building size and "appear to depend on building-specific conditions," including how much is partial versus full replacement.
  • The mean is higher than the median. That means some very expensive jobs pull the average up. A full rewire of a large, older, plaster-walled home can cost far more than the survey's middle range.
  • It is national. Respondents clustered on the West Coast and East Coast. Texas and Florida labor prices may differ.
  • Wall repair may not be included. Ask every bidder whether patching and painting are in the price.

An older LBNL presentation for ENERGY STAR (2023) gave a typical range of $250 to $750 per new circuit and $1,000 to $5,000 for a panel. That is a useful check when a quote lists circuits individually.

We did not find a dated, primary study giving a per-square-foot or per-opening rewiring price for Texas or Florida, so we do not publish one. When you collect quotes, ask the electrician to list the number of circuits, the number of openings (outlets, switches, lights) and whether the panel is included. That lets you compare bids line by line. See how to compare electrical quotes.

What drives the price up or down

FactorWhy it matters
Size of the home and number of openingsMore outlets, switches and lights means more labor and material
Wall typeDrywall is easy to cut and patch. Plaster and lath, common in older homes, is slower. Concrete block (CBS) walls in Florida need channels or surface raceway
AccessAn open attic or a crawlspace under a raised floor makes routing easy. A slab with a low-pitch roof and finished ceilings makes it hard
Number of storiesGetting wire from the attic to the first floor of a two-story home takes more fishing and more openings
Panel and serviceIf the panel or service must be replaced, add the panel cost, and current code adds a surge-protective device at the service
Code upgrades triggeredNew circuits need current AFCI, GFCI and tamper-resistant receptacle protection
Occupied vs emptyWorking around furniture and daily life takes longer than an empty house
Patching and paintingOften excluded from electrical quotes and billed by another trade
Hazards foundAsbestos-containing materials or old plaster coatings in older homes may need testing and special handling before walls are opened; ask before work starts

How do I know if my house needs rewiring?

No single age makes rewiring automatic. Look at what kind of wiring you have and what condition it is in.

Wiring types that usually push owners to rewire

  • Knob-and-tube, which has no ground and must not be buried in insulation. See knob-and-tube and cloth wiring.
  • Brittle cloth-insulated cable.
  • Single-strand aluminum branch wiring, installed from about 1965 to the mid-1970s. The CPSC calls copper rewiring the best method, though COPALUM or AlumiConn pigtailing are accepted permanent alternatives. See aluminum wiring.
  • Ungrounded circuits throughout the house, if you need grounded outlets for modern equipment. See two-prong outlets.

Warning signs in any house

  • Warm or discolored outlets and switch plates
  • Burning or hot plastic smells
  • Breakers that trip or fuses that blow often
  • Lights that flicker or dim when appliances start
  • Buzzing at outlets, switches or the panel
  • Many extension cords and power strips because there are not enough outlets
  • An insurer or 4-point inspection flagging the wiring

Some of these have simple fixes. Have a licensed electrician evaluate before assuming you need a full rewire. See breaker keeps tripping and burning smell.

Do I need to rewire a 1970s house? How long does home wiring last?

A 1970s house often has modern plastic-sheathed copper cable with a ground wire, which is usually in decent shape if it was not abused. The big exception is aluminum branch wiring. CPSC says cables installed between 1965 and the mid-1970s, in new homes, additions and rewired circuits, may contain aluminum. Check cable jackets in the attic for "Al" or "Aluminum." If you have it, remediation of every connection may be enough; a full copper rewire is the other permanent option.

Other 1970s issues are capacity, not age: 100-amp or smaller panels, too few kitchen circuits, and no GFCI or AFCI protection. These can often be solved with a panel upgrade and added circuits instead of a full rewire.

How long wiring lasts depends on the insulation type, heat, moisture and how it was treated. We found no authoritative fixed lifespan for home wiring, and you should be skeptical of anyone who quotes one as fact. Heat is the enemy: wiring in a hot Texas or Florida attic, or wiring that has been overloaded, ages faster. Insurers and inspectors judge by type and condition. In Texas, TDI clarified in September 2026 that insurers cannot decline or non-renew based on the age of wiring, only its physical condition.

What's included in a whole-house rewire?

A complete rewire quote should spell out:

  • New branch circuits from the panel to every outlet, switch, light and hard-wired appliance
  • New boxes where old boxes are too small or damaged
  • New devices: receptacles (tamper-resistant where required), switches, and GFCI and AFCI protection where the code requires it
  • Dedicated circuits for the kitchen, laundry, bathrooms, HVAC, water heater and any planned EV charger
  • Smoke alarm wiring where required
  • Panel replacement or upgrade, if needed, with a surge-protective device at the service
  • Grounding and bonding corrections
  • Disconnecting old wiring, and either removing it or abandoning it in place and documenting that it is dead
  • Permit, rough-in and final inspections
  • Whether patching, texture and painting are included or excluded
  • Cleanup, dust protection and daily work hours
  • Warranty terms for labor and materials

Code items that come with new circuits

  • AFCI protection. The 2023 NEC requires AFCI protection for 15- and 20-amp, 120-volt circuits in dwelling kitchens, family rooms, dining rooms, living rooms, bedrooms, closets, sunrooms, recreation rooms and similar areas (210.12(B)). Texas now uses the 2026 NEC; Florida uses the 2020 NEC until the 9th Edition takes effect.
  • GFCI protection in bathrooms, kitchens, laundry, garages, outdoors and other listed areas (210.8). Texas amended the 2026 NEC so outdoor dwelling HVAC outlets do not need GFCI.
  • Surge protection where service equipment is replaced (230.67), and an outdoor emergency disconnect for one- and two-family dwelling services (230.85, 2020 NEC).

Texas home inspectors check many of these under the TREC standards of practice, including missing GFCI and AFCI protection and receptacles under 5.5 feet that are not tamper resistant.

The rewiring process, step by step

  1. Evaluation. An electrician surveys the attic, crawlspace, panel and a sample of outlets, and maps existing circuits.
  2. Design and quote. The electrician plans circuit layout, routing paths, panel needs and where walls must be opened.
  3. Permit. The licensed contractor applies for the permit. In Houston, all work requiring an electrical permit must be done by a licensed electrical contractor, who schedules inspections. In Florida, s. 553.79 makes it unlawful to alter or repair a building without a required permit.
  4. Prep. Furniture moved, floors and belongings covered, and areas sealed for dust.
  5. Rough-in. New cable is fished through walls and ceilings, run in the attic or crawlspace, and new boxes installed. Old circuits stay live where possible so you keep some power.
  6. Rough-in inspection. The inspector checks wiring before walls and ceilings are closed. Do not patch until it passes.
  7. Cutover. New circuits are connected at the panel and old ones disconnected. Expect power to be off for part of a day or more if the panel is replaced, and a utility disconnect if the service changes.
  8. Trim-out. Devices, cover plates and fixtures installed.
  9. Final inspection. The inspector checks the finished installation. Keep the approval for your records and your insurer.
  10. Patch and paint. By the electrician or a separate drywall or plaster contractor.

Inspection steps and names vary by jurisdiction. Ask your contractor how many inspections your city or county requires. LBNL's 2026 survey found permit fees "vary more based on jurisdiction than project type."

How long does it take to rewire a house?

We found no dated study of whole-house rewiring durations. LBNL's 2026 survey found most single-family panel and service projects were completed within 30 days, with service rating increases taking longer, but that measured panel work, not rewiring.

Time depends on:

  • House size, number of openings and stories
  • Access through attics and crawlspaces
  • Wall type (drywall, plaster or concrete block)
  • Whether the house is occupied
  • Inspection scheduling in your city
  • Utility scheduling, if the service is being changed
  • Patching and painting afterward

Ask each contractor for a written schedule with milestones (rough-in complete, rough-in inspection, cutover, final) and what happens if inspections slip.

Can I live in my house while it's rewired?

Often yes, especially with a phased approach and good attic or crawlspace access. Expect:

  • Noise, dust and workers in the house during the day
  • Rooms emptied or furniture moved to the center
  • Some circuits off during the workday; plan for refrigerator and medical equipment needs
  • One or more days with no power when the panel is swapped
  • Holes in walls between rough-in and patching

Tips: ask the electrician to work room by room and restore power each night; keep one bathroom and the kitchen working as long as possible; store valuables and electronics; and make a plan for pets. In summer, ask how long the AC will be off. A Texas or Florida house without AC in July is not livable for some people. If anyone in the home depends on powered medical equipment, plan backup power with your electrician and see power for medical equipment.

Can you rewire a house without removing drywall?

Mostly, yes. Experienced electricians fish new cable through existing walls using small, targeted openings rather than tearing out whole walls. Typical openings are at the top plate (to drop wire from the attic), at the bottom plate (from a crawlspace), at each new box, and where wires cross fire blocking or framing. Openings are usually small, but there may be many of them.

How much opening you need depends on construction:

  • Single-story with an open attic: easiest. Most runs drop down from the attic.
  • Raised floor (pier-and-beam): runs can come up from below.
  • Two-story: first-floor ceilings and walls need more openings, sometimes through closets or soffits.
  • Plaster and lath: harder to fish and patch, and cracking can spread. Ask whether the electrician has plaster experience.
  • Concrete block: see the Florida section below.

Surface raceway (wiremold-style channel mounted on the wall) is another option where fishing is impossible. It costs less in patching but is visible.

Rewiring a slab-on-grade home in Texas: attic routing and heat

Many Texas homes sit on slab foundations, with no crawlspace or basement. That means almost all new wiring must come down from the attic. Slab homes are not necessarily harder to rewire, but they depend on attic access.

  • Attic access and pitch. Low-pitch roofs, tight eaves and blown insulation make attic work slow. The electrician may need to move insulation to reach top plates.
  • Heat. Texas attics are extremely hot in summer, which limits safe working hours. Expect early morning attic work, or schedule the project in cooler months.
  • Wires in the slab. Some slab homes have circuits run in conduit in or under the slab, such as to kitchen islands. These are hard to replace. Electricians often abandon them and reroute from above.
  • Exterior walls. Brick veneer homes may need some exterior outlets and lights reached from inside.
  • Licensing. In Texas, anyone performing electrical work must be licensed by TDLR and work through a TDLR-licensed electrical contractor. Verify on the TDLR license search.

Rewiring a concrete block (CBS) house in Florida

Concrete block and stucco (CBS) construction is common in Florida, especially in South Florida. Exterior walls are typically hollow concrete block with stucco outside and plaster or drywall over furring strips inside. That changes the rewiring method:

  • Wiring along furring strips. In many CBS homes, wires on exterior walls run in the narrow space between the block and the interior finish. Electricians can sometimes fish through that space.
  • Chasing the block. Where there is no space, the electrician may cut a channel (a chase) in the block or plaster for conduit, then patch over it. This is noisy, dusty and requires plaster or stucco repair.
  • Surface raceway. Mounting a channel on the wall surface avoids cutting block. It is common for adding outlets on block walls in older Miami-area homes.
  • Interior walls are often wood or metal stud framing and can be fished like any frame wall.
  • Attic routing is still the main path for most runs.
  • Plaster in older homes. Many older Miami, Tampa and other Florida homes have plaster finishes, which take skill to patch.
  • Licensing and permits. Hire a DBPR-licensed electrical contractor (EC certified statewide, or ER registered in your county or city). Florida's s. 553.79 requires a permit to alter or repair a building where code requires one, and the local building department inspects.

Ask Florida bidders specifically how they will reach outlets on exterior block walls, and whether the quote includes stucco or plaster repair.

Partial rewiring: is it an option?

Yes. Partial rewiring replaces the riskiest or most important circuits first. Common choices:

  • All attic circuits, where heat damage and old insulation are worst
  • The kitchen and bathrooms, where loads and water are highest
  • Bedrooms, where people sleep
  • Any knob-and-tube or brittle cloth circuits
  • Circuits flagged on an inspection report

Limits: insurers may want all of a problem wiring type gone. Florida 4-point forms ask about "active knob and tube" and single-strand aluminum, so a partial job that leaves those active may not satisfy the carrier. Partial work that extends or modifies existing circuits can also trigger AFCI protection under the 2020 NEC 210.12(D), which covers branch circuits that are extended or modified (with an exception for extensions of 6 feet or less without added outlets). Ask your insurer and your electrician together.

Should I upgrade the panel when rewiring? Does rewiring increase home value?

Panel: Often, yes. A rewire usually adds circuits, and old fuse boxes or small panels may not have room or capacity. Doing both together saves a second round of permits and power outages. When the service equipment is replaced, the NEC requires a surge-protective device (230.67). LBNL's 2026 survey put the national median single-family main panel replacement at $3,500. If you need more amperage from the utility, LBNL found median customer-side equipment cost of $2,800 for a service rating increase, plus a median $3,500 in utility-side costs passed to the customer. See panel upgrades.

Home value: We found no reliable, dated study measuring how much rewiring adds to sale price in Texas or Florida. The clearer benefits are practical: easier insurance (especially Florida 4-points), fewer inspection findings, cleaner disclosures (the Texas seller's disclosure notice asks about electrical defects and aluminum wiring), and lower fire risk. Keep permits, final inspection approval and the electrician's scope letter to show buyers and insurers.

Can I rewire my own house?

Legally, sometimes; practically, it is a big risk. In Texas, the state licensing law does not apply to work on a dwelling by a person who owns and lives in it, where the work is not specifically regulated by a city ordinance (Occupations Code 1305.003(a)(6)). Many Texas cities do regulate it, and Houston requires permitted electrical work to be done by a licensed electrical contractor. In Florida, the owner-builder exemption (s. 489.503(6)) lets an owner pull the permit and do electrical work on their own single-family home or duplex for their own use and occupancy, not for sale or lease. The owner must personally sign the permit application, and selling or leasing more than one owner-wired structure within a year of completion is evidence the work was done for sale, which violates the exemption.

Either way, the work must pass the same inspections, and insurers may ask who did it. See what electrical work you can legally do yourself.

Comparing rewiring bids

Rewiring bids vary widely, partly because contractors scope the job differently. Put them side by side on the same items: number of circuits, number of devices and fixtures, panel work, AFCI and GFCI devices, permit fees, who patches and paints, cleanup, schedule, and warranty. A low bid that excludes patching or the panel may end up costing more. Ask each bidder for references from similar houses (same era and wall type), confirm their license and insurance, and never pay the full price up front. In Texas, TDLR requires electrical contractors to carry liability insurance of at least $300,000 per occurrence. See how to hire an electrician.

How to choose a provider

  • Have a licensed electrician evaluate the wiring before assuming you need a full rewire.
  • Identify wiring types: knob-and-tube, cloth, aluminum branch, ungrounded.
  • Ask your insurer what it requires before choosing partial vs full.
  • Get at least three written quotes listing circuits, openings, panel work and patching.
  • Confirm the contractor's license (TDLR or DBPR) and that they will pull the permit.
  • Ask how they will route wire: attic, crawlspace, furring space, chases or raceway.
  • Get a written schedule with rough-in, inspections, cutover and final.
  • Plan for power-off periods, AC, food and medical equipment.
  • Do not patch walls until the rough-in inspection passes.
  • Keep the permit, final approval and electrician's letter for insurance and sale.

Related electricians guides

Electricians by state and city

Questions people ask

How much does it cost to rewire a house?

The LBNL August 2026 national survey found a median rewiring cost of $5,000 per single-family home, with a middle range of $1,000 to $7,500 and a mean of $7,021. It includes partial and full jobs. A full rewire of a large, older or plaster-walled home can cost more. Permit fees had a median of $129. Get several itemized quotes.

Does rewiring require a permit and inspection?

Yes, in nearly every case. Houston requires electrical permits for new circuits and rewired breakers, done by a licensed electrical contractor who schedules the inspections. Florida's s. 553.79 makes it unlawful to alter or repair a building without a required permit. Expect a rough-in inspection before walls are closed and a final inspection.

Can you rewire a house without removing drywall?

Mostly. Electricians fish new cable through existing walls using small openings at the top and bottom of walls and at each box, routing through the attic or crawlspace. Two-story homes, plaster walls and concrete block walls need more openings or surface raceway. Ask whether patching is included in the quote.

Can I live in my house while it's rewired?

Often yes. Many electricians work room by room and restore power at the end of each day. Expect noise, dust, holes in walls before patching, and at least one longer outage when the panel is changed. Plan for AC in summer, food, and any medical equipment that needs power.

Is it harder to rewire a slab home?

It depends on the attic. Slab homes have no crawlspace, so nearly all wiring comes down from the attic. A roomy attic makes it straightforward. A low-pitch roof, deep insulation or extreme summer heat slows the work. Circuits buried in the slab are usually abandoned and rerouted from above.

How is a concrete block house in Florida rewired?

Exterior CBS walls are typically hollow concrete block with stucco outside and plaster or drywall over furring strips inside. Electricians fish wires through the furring space where possible, cut a chase in the block or plaster for conduit where needed, or use surface raceway. Interior frame walls are easier. Ask how exterior-wall outlets will be reached.

Does rewiring increase home value?

We found no reliable study measuring the sale-price effect in Texas or Florida. Rewiring clearly helps with insurance, inspection findings and disclosures, and it lowers fire risk. Keep the permit, final inspection and electrician's letter, because buyers and insurers will ask for proof of what was replaced.

Should I upgrade the panel when rewiring?

Often. New circuits may not fit an old fuse box or small panel. Doing both together saves a second permit and outage. When service equipment is replaced, the NEC requires surge protection at the service. LBNL's 2026 survey put the national median single-family panel replacement at $3,500.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration