New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Fri, Nov 20, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Electricians

AC and Heat Pump Electrical Problems: Tripping Breakers, Disconnects, Capacitors, GFCI Rules and Who to Call in Texas and Florida

When the AC quits in a Texas or Florida summer, the cause is often electrical: a failing capacitor, a burned contactor, a blown disconnect fuse, a nuisance-tripping GFCI or a loose connection. This guide walks through safe checks you can do, what each symptom usually means, the GFCI rule changes for outdoor units, and exactly where the HVAC technician's license ends and the electrician's begins in each state.

An AC breaker that keeps tripping usually points to a failing capacitor, a compressor struggling to start, a shorted fan motor or wiring, loose connections, or a GFCI that is tripping on the outdoor unit. Call an HVAC technician for the unit itself (capacitor, contactor, motors, refrigerant) and a licensed electrician for the circuit, breaker, panel and new wiring. In Texas, licensed AC contractors may connect the equipment and its disconnect; in Florida, AC contractors may repair dedicated existing HVAC circuits but not run new power wiring.

Key facts

  • Texas exempts licensed air conditioning and refrigeration contractors from electrician licensing for the electrical connections to HVAC equipment, including the required disconnect for that equipment (Occ. Code 1305.003(a)(11)).
  • Florida Class A and B air-conditioning contractors may replace, disconnect or reconnect power wiring on either side of a dedicated existing disconnect on single-phase systems and repair or replace power wiring, disconnects, breakers or fuses for dedicated HVAC circuits, but their scope excludes other electrical power wiring (s. 489.105).
  • The 2020 NEC added GFCI protection for outdoor outlets at dwellings (210.8(F)), which caught AC condensers and led to nuisance-tripping complaints.
  • Texas amended NEC 210.8(F) in its 2026 NEC adoption (effective Sept. 1, 2026) so GFCI protection is not required on outdoor dwelling HVAC outlets.
  • A Florida Building Commission comment traces 210.8(F) to a proposal prompted in part by the electrocution of a 12-year-old who touched an energized AC condenser and a grounded metal fence.
  • Mike Holt's 2023 NEC analysis shows a 210.8(F) exception for listed HVAC equipment and requires GFCI on the HVAC service receptacle within 25 feet of the equipment (210.63).
  • TREC-licensed Texas home inspectors must report the absence of equipment disconnects as Deficient (22 TAC 535.229).
  • Houston requires an electrical permit whenever a new outlet or circuit is installed to serve a new or repaired appliance, and lists permits for wiring and equipment for motors.
  • Florida's 9th Edition Building Code (2023 NEC) takes effect December 31, 2026; Tampa says January 1, 2027.
  • Hurricane Beryl disrupted service to 2.7 million Texas customers on July 8, 2024, and the largest group of PUCT survey respondents were without power three to seven days.

First, safe checks you can do yourself

Before you call anyone, run through these steps. They are safe for a homeowner and solve a surprising share of "AC is dead" calls. Do not open the outdoor unit's service panel or the disconnect's inner cover.

  1. Thermostat. Set to Cool, a few degrees below room temperature, fan on Auto. Replace batteries if it has them. A blank screen can mean the low-voltage circuit lost power.
  2. Indoor breaker(s). Most systems have two: one for the outdoor condenser or heat pump (a 240-volt double-pole breaker) and one for the indoor air handler or furnace. A tripped breaker sits in the middle or off position. Turn it fully off, then on, once.
  3. Furnace or air handler switch. A light-switch-style service switch near the indoor unit is easy to bump off.
  4. Outdoor disconnect. Look at the box on the wall near the condenser. A pull-out block may be removed or inserted backward, or a lever may be off. Do not open the box's cover to look at fuses.
  5. Condensate safety switch. Many indoor units have a float switch that shuts the system off when the drain pan fills. Standing water around the indoor unit is a clue.
  6. GFCI. If your outdoor unit is on a GFCI breaker (it will have a TEST button), it may have tripped.
  7. Filter and outdoor coil. A clogged filter or a condenser buried in grass clippings makes the system work harder and can trip safeties.

If a breaker trips again right away, stop. Do not keep resetting it. Repeated resets can damage the compressor or heat wiring. Call for service.

Why does my AC breaker keep tripping?

A breaker trips when current exceeds its rating for long enough, or instantly on a short circuit. On AC circuits, these are the usual causes, roughly from most to least common:

CauseWhat you might noticeWho fixes it
Failing run capacitorHumming outdoor unit, fan not spinning, breaker trips after a minuteHVAC technician
Compressor struggling to start (high inrush, worn compressor)Lights dim hard, unit clicks and hums, trips on startHVAC technician; possibly a hard-start kit
Failed condenser fan motorFan blade not turning, unit overheats and tripsHVAC technician
Dirty condenser coil or clogged filterTrips on very hot afternoons, long run timesOwner (filter) or HVAC technician (coil cleaning)
Loose or corroded connections at the breaker, disconnect or contactorBurning smell, discolored terminals, intermittent tripsElectrician for the circuit, HVAC tech for the unit
Wiring damage (lawn equipment, rodents, flooding)Instant trip, visible damage to the whip between disconnect and unitElectrician or HVAC contractor within its scope
Breaker worn or wrong size for the nameplateTrips despite a healthy unit, or breaker is warmElectrician
GFCI nuisance trippingGFCI breaker trips on start, especially newer variable-speed unitsElectrician and HVAC tech together
Refrigerant problems (overcharge, restriction)High head pressure, unit runs hotHVAC technician (EPA-certified for refrigerant)

One rule never changes: do not replace the breaker with a larger one to stop the trips. The breaker must not exceed the unit's MOCP (maximum overcurrent protection) printed on the nameplate, and the wire must meet its MCA (minimum circuit ampacity). Florida's Citizens 4-point form specifically asks inspectors about over-fusing and improper breaker size, and insurers notice.

Who do you call for AC electrical problems, HVAC tech or electrician?

The short answer: the HVAC technician owns the equipment; the electrician owns the circuit that feeds it. Where they meet, the line differs by state.

TaskTexasFlorida
Replace capacitor, contactor, fan motor, compressor, control boardLicensed ACR contractor (TDLR, Occ. Code Ch. 1302)Licensed Class A or B air-conditioning or mechanical contractor (s. 489.105)
Connect the new unit's power wiring and its required disconnectACR contractor may do it without an electrician license (Sec. 1305.003(a)(11))AC contractor may replace, disconnect or reconnect power wiring on the line or load side of the dedicated existing disconnect on single-phase systems
Replace a damaged disconnect, breaker or fuses on a dedicated HVAC circuitACR contractor for the equipment disconnect; electrician for panel workAC contractor may repair or replace power wiring, disconnects, breakers or fuses for dedicated HVAC circuits, using a circuit breaker lock
Run a new circuit from the panel (new unit location, bigger unit)Licensed electrician through an electrical contractor (the ACR exemption covers connections to the equipment; ask the ACR contractor and city how they apply it)Licensed electrical contractor; AC contractor scope excludes other "electrical power wiring"
Panel replacement or service upgrade for added loadLicensed electricianLicensed electrical contractor
Thermostat and low-voltage control wiringACR contractor; low-voltage is exempt from electrician licensing (Sec. 1305.003(a)(12))AC contractor may install and reconnect low-voltage HVAC control wiring

So in Florida, if a new heat pump needs a 40-amp circuit and your old unit had a 30-amp circuit, that upsizing is electrical contractor work. In Texas, the ACR exemption is broader at the equipment connection, but new panel work is still electrician work. Many HVAC companies in both states employ or subcontract a licensed electrician for this reason. Ask who will do which part, and who pulls the permit.

Verify the HVAC license on TDLR's license search (Texas, Air Conditioning and Refrigeration Contractors) or on DBPR's portal (Florida, construction industry licenses), and the electrician on TDLR (electricians) or DBPR (ECLB). See our electrician vs handyman vs HVAC guide.

What is the AC disconnect box outside?

It is the small metal box mounted on the wall near your outdoor unit. It lets a technician cut power to the unit right where they are working, instead of walking back to the panel. The code requires a disconnecting means for air-conditioning equipment, Texas law refers to it as "the required disconnect" for HVAC equipment (Sec. 1305.003(a)(11)), and TREC-licensed home inspectors in Texas must report missing equipment disconnects as Deficient.

Common types

  • Non-fused pull-out: a plastic block you pull out to cut power. The circuit is protected by the breaker in the panel.
  • Fused pull-out: the pull-out block or the box holds cartridge fuses that protect the unit.
  • Lever or toggle switch: a handle you move to off.
  • Molded-case breaker in the box: a small breaker enclosure acting as the disconnect.

Safety points

  • Pulling the disconnect de-energizes the unit side only. The incoming wires (line side) inside the box stay live until the panel breaker is off.
  • Rust, water inside the box, or a melted pull-out block are reasons to call for repair, not to keep using it.
  • After flooding or storm surge, NEMA's 2026 guide says water-exposed disconnects, breakers and many devices should be evaluated by qualified personnel, and molded-case breakers exposed to water should be replaced. See flood-damaged electrical.

Why does the AC fuse in the disconnect blow?

A blown fuse is the fused-disconnect version of a tripped breaker. Common reasons:

  • A failing capacitor or hard-starting compressor drawing high current.
  • A short in the unit or in the whip (the flexible conduit from the disconnect to the unit).
  • Fuses of the wrong type or size. Fuses must not exceed the nameplate MOCP, and time-delay fuses are commonly specified for motor loads.
  • Heat and corrosion at the fuse clips, which raises resistance and heat until the fuse opens.
  • Age. Fuses can fatigue after years of compressor starts.

Replacing a fuse means working inside an energized enclosure unless the panel breaker is off and you have tested for voltage. That is technician work. If a new fuse blows quickly, the fuse is not the problem.

Can an electrician replace an AC disconnect?

Yes. A licensed electrician can replace a disconnect in either state, and it is a common job when the box is rusted, overheated, or undersized for a new unit. In Texas, a licensed ACR contractor may also replace the required equipment disconnect under the Sec. 1305.003(a)(11) exemption. In Florida, a licensed AC contractor may repair or replace disconnects for dedicated HVAC circuits under s. 489.105. Many cities treat a disconnect replacement as permit work; Houston lists electrical permits for wiring and equipment for motors and for any new outlet or circuit serving an appliance. Ask whoever does it to pull the permit.

Why is my AC not turning on but the breaker is fine?

A breaker that has not tripped only tells you the 240-volt power is available. Many other parts can stop the system:

SymptomLikely cause
Thermostat blankDead batteries, indoor unit switch off, tripped indoor breaker, blown low-voltage fuse on the control board, or a tripped float switch
Indoor fan runs, outdoor unit silentDisconnect pulled or fuse blown, failed contactor, low-voltage wire cut outside, safety lockout
Outdoor unit hums, fan does not spinFailed capacitor or seized fan motor
Outdoor unit clicks on and offFailing contactor, control problem, or a pressure switch cycling
Nothing at all after a stormDamaged disconnect, flooded unit, or a utility problem on part of the service
Some lights work, AC and range do notLoss of one leg of the 240-volt service, which can be on the utility side or in the panel

The last row is worth explaining. A home service has two 120-volt "legs." Losing one leg can leave half the house lit while 240-volt loads like the AC, dryer and range stop. That is often a utility issue. In San Antonio, CPS Energy takes electric emergency reports at 210-353-HELP (4357) and power quality questions at 210-353-2222; CPS says its responsibility ends where service reaches the building. Report outages to your utility first. See power out in part of the house.

What does a bad capacitor sound like?

The run capacitor stores and releases energy to start and run the compressor and fan motors. When it weakens:

  • The outdoor unit hums but the fan does not spin, or spins slowly.
  • You may hear clicking as the compressor tries and fails to start, then trips on overload.
  • The fan may start if nudged, a sign the motor lacks starting help. Do not nudge it; the blade can start suddenly.
  • The capacitor can look swollen on top or leak oil.

Capacitors hold a charge even with power off and can shock you. Replacing one is a technician job with the disconnect and breaker off and the capacitor safely discharged. We did not find a named, dated cost study for capacitor replacement in Texas or Florida, so we are not quoting a price; get a written quote that lists the part rating.

What is a hard-start kit, and do you need one?

A hard-start kit adds a start capacitor and a relay that give a compressor an extra push at startup, reducing the time it struggles at high current. A technician may suggest one when:

  • The compressor is older and starts hard.
  • Lights dim noticeably every time the AC starts.
  • A standby generator or battery system struggles to start the AC.
  • The manufacturer recommends one for the model.

A hard-start kit is not a cure for a failing compressor, a refrigerant problem or a wiring fault, and some manufacturers specify which kits are approved. Ask the technician to explain why it is needed for your unit and whether it affects the equipment warranty. Some newer variable-speed systems use soft-start electronics instead.

Why do my lights dim when the AC starts?

A compressor draws a surge of current for a fraction of a second when it starts. A brief, slight dip in the lights at that moment is common. It becomes a concern when:

  • The dimming is deep or lasts more than a moment.
  • Lights get brighter in some rooms and dimmer in others. That pattern can signal a loose neutral, which is a hazard. Turn off sensitive electronics and call an electrician or your utility right away.
  • It started suddenly after a storm or tree contact with the service drop.
  • You also smell burning at the panel or meter.

Fixes range from a hard-start or soft-start device on the compressor to tightening connections, replacing a damaged service drop (the utility's side) or correcting a weak meter base (usually the owner's side). See flickering and dimming lights and meter base responsibility.

Does my outdoor AC need GFCI protection now?

This is one of the most confusing code questions in the trade, because the answer changed across editions and the two states now differ.

How the rule developed

  • 2020 NEC: section 210.8(F) added GFCI protection for outdoor outlets at dwellings, not just receptacles, per Miami-Dade's summary of the 8th Edition Florida Building Code changes. "Outlet" includes the point where an AC condenser is hardwired. Many variable-speed condensers and heat pumps then tripped GFCI breakers on startup.
  • Why it was added: a 2026 Florida Building Commission comment traces the rule to a public input for the 2020 NEC prompted in part by the electrocution of a 12-year-old who touched an energized residential AC condenser and a grounded metal fence at the same time.
  • 2023 NEC: Mike Holt's analysis of the 2023 changes shows 210.8(F) covering outdoor outlets rated 50 amps or less, with an exception stating GFCI protection is not required for listed HVAC equipment such as compressors or heat pumps. Separately, the 125-volt service receptacle that must be within 25 feet of HVAC equipment (210.63) does require GFCI protection.
  • Texas, 2026 NEC: when TDLR adopted the 2026 NEC effective September 1, 2026, the Commission approved an amendment to 210.8(F) so that GFCI protection is not required on outdoor dwelling HVAC outlets.
  • Florida: the 8th Edition uses the 2020 NEC today. The 9th Edition, based on the 2023 NEC, takes effect December 31, 2026 (Tampa says January 1, 2027). The Florida Building Commission's 2026 glitch process included a proposed Florida amendment to 210.8(F) and public comments urging caution. Ask your building department which version applies to your permit.

What to do

  • If your existing unit is on a GFCI breaker that trips, do not just swap in a standard breaker. Ask an electrician whether your installation's code edition and local amendments allow it, and whether a newer GFCI device designed for these loads solves the problem.
  • Never defeat a GFCI permanently by yourself. The rule exists because of a real death.
  • Keep metal fences, grills and pool equipment from touching the condenser cabinet, and make sure the unit is properly grounded. See GFCI and AFCI requirements.

Summer overloads, heat waves and the grid

Texas and Florida run their AC hard for months. Electrical problems cluster in the same weeks:

  • Weak parts fail under heat. Capacitors and contactors that limp through spring often fail on the first 100-degree week. Ask for an inspection before summer.
  • Connections heat up. Loose lugs at the breaker or disconnect run hotter under long run times, leading to discoloration and failure.
  • Storm damage. Hurricanes and derechos damage service drops, meter bases and outdoor units. PUCT reported that Hurricane Beryl disrupted service to 2.7 million Texas customers on July 8, 2024, including 2.2 million CenterPoint customers, and the May 16, 2024 Houston derecho caused over 1 million outages. Utilities in both states require customer-owned meter equipment to be repaired by a licensed electrician before reconnection.
  • Winter, too. Heat pumps with electric resistance backup draw very large loads in a freeze. During Winter Storm Uri in February 2021, ERCOT shed up to 20,000 MW of load. LBNL researchers recommend avoiding reliance on backup resistance heat where possible.

When power returns after an outage, many systems restart at once. If your AC trips or will not restart after power is restored, turn the thermostat off, wait several minutes, then turn it back on. If it still trips, call for service. See ERCOT grid outages and reporting outages.

The contactor: the other part that fails every summer

The contactor is the heavy-duty switch inside the outdoor unit. When the thermostat calls for cooling, a 24-volt signal pulls the contactor closed and sends 240 volts to the compressor and fan. Each start creates a small arc across its contacts, so after years of cycling the contacts pit and burn.

  • Pitted contacts raise resistance, heat the contactor and can make the compressor start poorly.
  • Welded contacts leave the outdoor unit running even when the thermostat is off. If your condenser will not stop, turn it off at the disconnect or breaker and call for service.
  • Ants and debris are a common warm-climate problem. Insects and debris can lodge between contacts and stop them from closing properly.
  • A failed coil means the contactor never pulls in. The indoor fan runs but the outdoor unit stays silent.

A contactor replacement is HVAC technician work, done with power off at the disconnect and breaker. It is often paired with a capacitor check because both age together.

Heat pump electrical problems, including winter trips

A heat pump is an AC that runs in reverse for heating, so it shares the same outdoor electrical parts. It adds a few of its own:

  • Auxiliary or emergency heat strips. Electric resistance heaters in the indoor air handler back up the heat pump in cold weather. They are often fed by a separate 240-volt circuit, and sometimes two breakers. They draw large current, so a tripping air handler breaker in winter often points to the strips, a failed sequencer or a loose lug.
  • Defrost cycles. In cold, damp weather the outdoor coil frosts and the system briefly switches to cooling mode to melt it, with a whoosh and steam. That is normal. A unit stuck in defrost or never defrosting is a control or sensor problem.
  • Freeze events. In Winter Storm Uri in February 2021, ERCOT generation out of service peaked at 52,277 MW and load shed reached 20,000 MW. When power returns after a winter outage, many heat pumps and heat strips start at once. Staggering restarts helps.
  • Running on strips alone. LBNL researchers recommend low-power heat pumps without backup resistance heat where possible, because resistance heat is the big load that drives panel and service sizing. A Vermont dataset cited in the 2023 ENERGY STAR presentation found adding heat pumps raised average 15-minute demand by about 200 watts when backup resistance heat was avoided.

If the indoor breaker for the heat strips trips repeatedly, leave it off and call. Running a heat pump on emergency heat with a damaged strip circuit is a fire risk.

Mini-split and inverter system electrical issues

Ductless mini-splits and many new central systems use inverter-driven, variable-speed compressors. Electrically they behave differently from older single-speed units:

  • They usually start softly, so the lights-dim-on-start problem largely goes away.
  • Their electronics are sensitive to surges and poor power quality. Lightning, utility switching and storm restorations can damage boards.
  • They show error codes on the indoor unit or remote. Write the code down before calling; it tells the technician whether the fault is communication wiring, a sensor, or power.
  • The communication cable between indoor and outdoor units on many mini-splits carries line voltage as well as data. Treat it as power wiring.
  • Their electronics are the reason GFCI devices sometimes trip on outdoor HVAC circuits, which fed the 210.8(F) debate.

The 2020 NEC requires a surge-protective device in or next to the service equipment at dwellings (230.67), and Mike Holt notes the rule was driven partly by sensitive electronics. A whole-house SPD does not guarantee protection from a direct strike, but it is a sensible layer for homes with inverter HVAC. See whole-house surge protection and lightning strikes.

Running your AC on a generator or battery

Central AC is often the load that decides generator and battery size. Key points:

  • Never backfeed. CPSC warns never to power house wiring by plugging a generator into a wall outlet, because it can electrocute utility workers and neighbors. Use a transfer switch or a listed interlock installed by a licensed electrician. OSHA also says generators should not be connected to a building's electrical system except through properly wired isolation connections.
  • Starting current matters. A compressor's starting surge can be several times its running current. A soft-start device or an inverter unit can let a smaller generator or battery start the AC.
  • Carbon monoxide. CPSC says most portable generator incidents it receives involve CO poisoning. Keep generators outdoors, far from windows, doors and vents, and use battery-backed CO alarms.
  • Load management. Some transfer switches shed the AC when other large loads run.

See transfer switches and interlocks, standby generators and home battery backup. If anyone at home depends on cooling for medical reasons, see medical equipment backup.

What a technician should test on an electrical AC call

A good diagnostic visit checks the electrical side systematically. Ask the technician to note:

  • Voltage at the disconnect and at the contactor, both at rest and during startup
  • Running current of the compressor and fan compared with the nameplate ratings
  • Capacitor measured value compared with its rated value
  • Condition of contactor contacts and the coil
  • Tightness and condition of terminals at the breaker, disconnect and unit
  • The whip and conduit between disconnect and unit for damage
  • Breaker and fuse sizes compared with the nameplate MOCP
  • Grounding of the cabinet

Written readings make it easier to compare quotes and to show an electrician exactly what the HVAC technician found if the problem is on the supply side.

A pre-summer electrical checkup for your AC

  1. Replace the filter and keep a spare.
  2. Clear plants, debris and grass clippings at least a couple of feet around the condenser.
  3. Look at the disconnect: closed cover, no rust-through, no scorch marks.
  4. Check that the panel directory clearly labels the AC and air handler breakers.
  5. Test any GFCI on the HVAC service receptacle near the unit.
  6. Book a professional tune-up that includes capacitor and contactor checks.
  7. If you had storm or flood damage last season, ask for an electrical evaluation of the outdoor unit and disconnect.
  8. Plan for outages: know how to reset the system after power returns, and how your generator or battery handles the AC.

New AC or heat pump? Electrical questions to ask before you sign

  1. Will the existing circuit work? Compare the new unit's MCA and MOCP with the existing wire and breaker. A larger unit may need a new circuit.
  2. Is there panel space and service capacity? Heat pumps with resistance heat strips can add a large indoor load. LBNL's 2023 ENERGY STAR presentation noted that only about 4.6 percent of heat pump upgrades in one California program involved a panel replacement, but heat strips change the math.
  3. Who pulls which permit? Mechanical and electrical permits may be separate.
  4. Is the disconnect being replaced? Old disconnects are often rusted or undersized.
  5. GFCI or not? Ask how the installer will meet the code edition in force for your permit, especially in Florida around the 9th Edition changeover.
  6. Generator compatibility. If you have or plan a standby generator, ask about soft-start devices. See standby generators.

For panel and service upgrade costs, LBNL's August 2026 national survey reported a median $3,500 for a main panel replacement and a median $2,800 in equipment for a service rating increase, plus $3,500 in utility-side costs passed to the customer. See panel upgrades and dedicated circuits.

Water shut-offs: float switches and condensate problems

In humid Texas and Florida summers, an AC removes a lot of water from the air. That water drains from the indoor coil through a condensate line. When the line clogs with algae or debris, a float or condensate safety switch cuts power to the system, usually by interrupting the low-voltage control circuit, to prevent an overflow.

  • The result looks electrical: the thermostat may go blank or the outdoor unit will not start, yet no breaker has tripped.
  • Signs: water in the secondary drain pan, a wet ceiling stain below an attic unit, or water around a closet unit.
  • Clearing the drain line is HVAC maintenance. Do not bypass the float switch, because an overflow can damage ceilings and reach electrical fixtures below.

Water dripping onto electrical parts, or a ceiling light fixture filling with water under an attic unit, is a shock and fire hazard. Turn off that circuit and call for service.

Insurance, warranties and AC electrical damage

Electrical damage to an AC raises three money questions.

  • Homeowners insurance. Coverage for lightning, power surge or storm damage to an AC depends on your policy wording and the cause. Ask your agent before you authorize replacement, and keep the technician's written findings. In Texas, the TDI Help Line is 800-252-3439. TDI also notes most homeowners and renters policies pay a limited amount for food spoiled during some power outages.
  • Manufacturer warranty. Read the equipment warranty for installation and registration conditions. Keep the installer's license number and invoice.
  • Contractor workmanship. If a new system keeps tripping soon after installation, notify the installer in writing. See warranty callbacks.

Florida homeowners should also expect insurers to ask about the electrical system on older homes through the 4-point inspection, which records panel details and hazards like over-fusing. See 4-point electrical.

Burning smell, sparks or melted parts at the AC

Treat these as emergencies:

  • Burning or hot plastic smell at the indoor unit, outdoor unit, disconnect or panel
  • Visible sparks, arcing sounds or smoke
  • A melted pull-out block, discolored breaker or scorched wire

Turn the thermostat off, turn off the AC breaker(s) at the panel if you can do so safely, and stay away from the outdoor unit. If there is smoke or fire, leave and call 911. Then call for repair. USFA estimated 23,700 residential building electrical malfunction fires in 2023 nationally. See burning smell and when to call.

Landlords and tenants: AC electrical problems in rentals

In Texas, a landlord must make a diligent effort to repair a condition that materially affects the physical health or safety of an ordinary tenant after the tenant gives proper notice and is current on rent (Property Code 92.052). There is a rebuttable presumption that seven days is a reasonable time to repair (92.056(d)). Whether a dead AC qualifies can depend on the facts, such as extreme heat and a vulnerable occupant. A sparking disconnect or exposed wiring is a safety condition.

In Florida, landlords must comply with applicable building, housing and health codes (s. 83.51). Local housing codes may address cooling. A tenant may terminate if the landlord materially fails to comply within 7 days after written notice stating the intent to terminate (s. 83.56(1)).

Tenants should not open disconnects or replace breakers. Report problems in writing and keep a copy. This is general information, not legal advice. See landlord and tenant electrical.

How to choose a provider

  • Check thermostat settings and batteries.
  • Reset the AC and air handler breakers once; if they trip again, stop.
  • Check the indoor service switch, the outdoor disconnect position and any GFCI.
  • Look for standing water at the indoor unit (float switch).
  • Replace a clogged filter and clear debris from the outdoor unit.
  • Note symptoms: humming, clicking, fan not spinning, dimming lights, burning smell.
  • Call an HVAC technician for the unit and an electrician for circuits, panels and new wiring.
  • Never install a breaker larger than the nameplate MOCP or bypass a GFCI.
  • Ask who pulls the permit for disconnect, circuit or panel work.

Related electricians guides

Electricians by state and city

Questions people ask

Can I reset my AC breaker myself?

Yes, once. Turn it fully off, then on. If it trips again right away or within minutes, leave it off and call for service, because repeated resets can damage the compressor or overheat wiring. Also check that the outdoor disconnect is fully seated and that any GFCI breaker has not tripped.

Why does my AC trip the breaker only on hot afternoons?

Heat raises the pressure the compressor works against, which raises current. A weak capacitor, dirty condenser coil, failing fan motor, or loose connection that runs fine in mild weather can push current over the breaker rating on the hottest days. Clean the area around the outdoor unit and replace the filter, then call an HVAC technician if it continues.

Can my HVAC company replace my breaker panel?

Not under its HVAC license. In Texas, panel work is electrical work for a licensed electrician through an electrical contractor; the ACR exemption covers connections to the HVAC equipment and its disconnect. In Florida, AC contractors may repair breakers on dedicated HVAC circuits but not do other electrical power wiring. Many HVAC firms bring in a licensed electrician.

Is it safe to pull the AC disconnect myself?

Pulling a disconnect to shut the unit off is designed to be safe for a homeowner, but only if the box is intact and dry. Do not touch it if it is rusted through, wet or damaged, and never reach inside. Remember that the incoming wires in the box stay live until the panel breaker is off.

Why does my AC GFCI breaker keep tripping?

Many newer variable-speed condensers and heat pumps have electronics that can trip some GFCI devices, a problem that followed the 2020 NEC outdoor-outlet GFCI rule. Texas has since amended the rule so GFCI is not required on outdoor dwelling HVAC outlets under its 2026 NEC adoption. In Florida, ask an electrician what your permit's code edition requires. Do not simply bypass it.

What does MCA and MOCP mean on my AC unit?

MCA is minimum circuit ampacity, the smallest current rating the circuit wire must have. MOCP is maximum overcurrent protection, the largest breaker or fuse allowed. Your breaker must not exceed the MOCP. If a breaker keeps tripping, a bigger breaker is not a fix and can be a fire risk.

Who is responsible if a storm damages the wires to my AC?

Customer-owned equipment, including the AC unit, disconnect and wiring, is the owner's responsibility, usually through homeowners insurance if a covered event caused the damage. The utility owns the service line and meter. Utilities such as FPL, JEA and Oncor require customer-owned equipment to be repaired by a licensed electrician and inspected where required before reconnecting.

Can a bad AC capacitor cause a fire?

A failing capacitor more often causes the motor to overheat and trip the breaker or fuse, which is the safety system working. Overheated connections, swollen capacitors and burned contactors can still damage wiring. Any burning smell, scorch marks or melted parts mean turn the system off and call a technician.

What size breaker does my AC need?

The breaker size comes from the unit's nameplate, not from the tonnage. The breaker or fuse must not exceed the maximum overcurrent protection (MOCP) on the label, and the wire must meet the minimum circuit ampacity (MCA). Two units of the same tonnage can have different ratings. An installer should size the circuit from the nameplate and installation instructions.

Should my AC be on its own breaker?

Yes. Central AC condensers, heat pumps and mini-splits are installed on their own 240-volt circuits, and the indoor air handler or furnace usually has its own circuit, sometimes two if it has heat strips. If anything else is connected to the AC circuit, ask an electrician to check it.

Why does my outdoor AC unit hum when it is supposed to be off?

A faint hum can come from a crankcase heater or the control transformer on some units, which is normal. A loud hum with the fan not turning, or a unit that keeps running when the thermostat is off, can mean a stuck contactor or failing capacitor. Turn the unit off at the disconnect or breaker and call an HVAC technician.

Do I need a permit to replace my AC?

Usually yes. Cities and counties require mechanical permits for HVAC replacement, and electrical work such as a new circuit or disconnect may need an electrical permit. In Florida, a Notice of Commencement is not required by the permit office for repair or replacement of an existing heating or air-conditioning system under $15,000 (s. 713.135). Ask the contractor to list permits on the quote.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration