Local Guide · Electricians
Why Are My Lights Flickering or Dimming? Normal vs Dangerous
A quick dip when the AC starts is normal. Lights that flicker in one room, pulse at night, or get brighter when something turns on are not. Here is how to sort it out, and who to call in Texas and Florida.
A brief dim when a big motor such as the AC starts is normal. Flickering confined to one bulb or fixture is usually a loose bulb, a failing LED or a dimmer that does not match the bulb. Flickering in one room points to a loose connection. Whole-house flickering, or lights that get brighter when appliances run, can mean a loose neutral or a utility problem: report it to your utility (in deregulated Texas, your wires company such as Oncor or CenterPoint) and have an electrician check your side.
Key facts
- CPS Energy says AC units draw a large amount of current at startup, which can cause a momentary voltage dip, and that this is normal depending on the unit's size.
- CPS Energy says its automatic protection devices can operate as many as three times when trying to restore power, which explains brief blinks before an outage.
- Texas utilities must keep distribution voltage within the limits of ANSI C84.1 and must use monitoring instruments to investigate customer power quality complaints (16 TAC 25.51).
- Florida utilities must keep voltage at the point of delivery within 5% above or below their adopted standard voltage (Fla. Admin. Code R. 25-6.046).
- Oncor delivers electricity but does not sell it; in deregulated Texas the delivery company, not the retail provider, handles outages and equipment.
- CPSC says a loose screw holding a wire or a worn-out switch can lead to arcing, overheating or fire, and that outlets and switches that do not work properly may indicate unsafe wiring.
- CPS Energy takes power quality investigation requests at 210-353-2222.
Normal or dangerous? Start here
| What you see | Usually means | What to do |
|---|---|---|
| Lights dip for a second when the AC, fridge, well pump or vacuum starts | Normal motor starting current | Nothing, unless the dip is deep, long, or getting worse |
| One bulb flickers | Loose bulb, failing LED, incompatible dimmer | Tighten or swap the bulb; check dimmer compatibility |
| One fixture flickers with several bulbs | Loose socket or fixture connection, failing driver | Electrician or a careful fixture repair |
| Several lights in one room or on one circuit flicker | Loose connection at a switch, outlet or splice on that circuit | Electrician soon; loose connections heat up |
| Whole house flickers, especially in wind or storms | Loose service connection, tree limbs on lines, utility equipment | Report to the utility |
| Lights get brighter when something big turns on, or dim on one side and bright on the other | Loose or lost neutral | Urgent: unplug electronics, call the utility, then an electrician |
| Lights blink off and on a few times, then the power goes out | Utility protective devices trying to clear a fault | Wait; report if the outage continues |
The key question is whether the flicker is confined (one bulb, one fixture, one room) or widespread (many rooms, the whole house, the neighbors too). Confined problems are inside your home. Widespread problems are often at the service or on the utility's side.
Why do lights dim when the AC kicks on?
Electric motors draw a big rush of current for a moment as they start. CPS Energy explains that AC units draw a large amount of current at startup, which can cause a momentary drop in voltage, and that this is normal depending on the size of the unit. Your lights share the same service wires, so they dip for a fraction of a second.
A brief dip is fine. These signs are not:
- The dip lasts more than a second or two.
- The dip is getting deeper over weeks or months.
- The AC hums or struggles to start, or its breaker trips.
- Lights get brighter instead of dimmer, or some rooms dim while others brighten.
A growing dip can mean a weakening AC capacitor or compressor (an HVAC issue), a loose connection at the panel, meter base or service drop (an electrician or utility issue), or a service that is undersized for the home's loads. In Texas and Florida summers, an aging AC can make the problem worse. See HVAC electrical and panel upgrades.
Why do LED bulbs flicker on a dimmer?
This is the most common flicker complaint today, and it is usually a compatibility problem, not a wiring fault.
- Non-dimmable LEDs on a dimmer. Only bulbs marked dimmable should be used on a dimmer.
- Old incandescent-era dimmers. Many older dimmers were designed for heavy incandescent loads. A few LED bulbs draw so little power that the dimmer cannot control them smoothly, which causes flicker, buzzing or a light that will not turn fully off.
- Leading-edge vs trailing-edge dimmers. Dimmers cut part of each power wave. Leading-edge (often called incandescent or magnetic low-voltage) dimmers cut the front of the wave. Trailing-edge (often called ELV, for electronic low-voltage) dimmers cut the back of the wave and tend to work better with many LED drivers. Bulb and fixture makers publish lists of dimmers they have tested.
- Low-end trim setting. Many LED-rated dimmers have a small adjustment that sets the lowest level. Raising it can stop flicker at low brightness.
- Mixing bulb brands on one dimmer can cause uneven dimming or flicker.
Fix: check the bulb package and the dimmer's compatibility list, use matching bulbs, and replace older dimmers with ones rated for LED. Replacing a dimmer is wiring work. Turn off the breaker first, and know your local rules. See LED lighting upgrades and DIY electrical limits.
Do smart bulbs flicker more?
They can. Smart bulbs need constant power for their radio. When they are put on a regular dimmer, or a smart switch is installed that sends a little current through the bulb when "off," the bulb can flicker, glow faintly, or reboot. Smart switches that lack a neutral wire are a common culprit in older homes, because some of them pass a trickle of current through the bulb to power themselves.
- Do not put smart bulbs on a dimmer; control them with the app or a compatible smart remote.
- If you use smart switches, choose one that matches your wiring. Many older switch boxes have no neutral wire.
- Weak Wi-Fi does not cause flicker by itself, but a bulb losing connection can blink as it rejoins.
Why do my lights flicker in one room only?
When several lights in one room or on one circuit flicker but the rest of the house is fine, the cause is almost always a loose connection on that circuit. It might be at a switch, a fixture, an outlet (lights and outlets often share circuits), a splice in a junction box, or where the circuit's wire attaches to its breaker.
Loose connections matter because they heat up. CPSC's checklist warns that a loose screw holding a wire or a worn-out switch can lead to arcing, overheating or a fire. Signs it is getting worse: the switch or cover plate feels warm, you hear crackling or buzzing, you smell something like hot plastic or fish, or the breaker for that room has started tripping.
What you can safely do: replace the bulb, try a different bulb type, and see if wiggling the switch changes anything (if it does, the switch is suspect). Then call an electrician. If you smell burning, see our burning smell guide.
Can a bad neutral cause lights to flicker?
Yes, and it is the most important cause to rule out. Your home's two 120-volt legs share a neutral. If that neutral connection becomes loose at the transformer, service drop, meter base or panel, voltage on each leg starts to swing based on what is running. Lights on one side dim while the other side gets brighter. They may flicker as the connection makes and breaks.
A loose neutral can push voltage on one side well above normal and damage electronics and appliances, and the loose connection itself can overheat. If you see lights get brighter when a big appliance starts, or a mix of very dim and very bright lights:
- Turn off and unplug sensitive electronics.
- Call your utility's outage or emergency line. Ask them to check the service drop and neutral connection.
- If the utility finds its side is fine, call a licensed electrician to check the meter base and panel.
More in power out in half the house.
Is whole-house flickering a utility problem?
Often, but not always. Whole-house flicker can come from:
- Utility side: a failing transformer connection, a loose service drop connection, tree limbs brushing lines, or protective devices on the line operating.
- Your side: a loose connection in the meter base, a loose main lug in the panel, or a failing main breaker.
- Big loads nearby: a neighbor's large equipment on the same transformer, or your own AC or well pump.
A good test: ask a neighbor on the same transformer whether they see it too. If they do, the utility is the place to start.
Why do lights blink a few times before the power goes out?
CPS Energy explains that its system has protection devices that switch off automatically when there is a problem, such as a branch touching a line, and then try to restore power. These systems can operate as many as three times. If the problem clears, the lights come back after a blink. If not, the line stays off and a crew is sent.
Why do lights flicker when it's windy?
Wind moves wires. If tree limbs touch the lines, or the service drop to your house has a loose connection, each gust can cause a brief flicker. Wind can also stress the weatherhead and the connections where the utility's wires join yours.
Do not trim trees near power lines yourself. Oncor, for example, says that for limbs near the service line from the pole to your meter, you should hire a qualified tree trimmer and request a temporary disconnect so the line can be safely lowered, and that only line-clearance-certified personnel may work within 6 feet of high-voltage lines. Report limbs on lines to your utility. If you see sparking or fire, call 911.
If the weatherhead, riser or meter box looks damaged, those parts are usually customer-owned. See meter base and service drop responsibility.
Why do lights pulse or strobe at night?
Slow pulsing at night has a few common explanations:
- Load changes. In the evening, AC units, pool pumps and other loads in the neighborhood cycle on and off, and voltage shifts slightly. Some LED bulbs, especially low-cost ones, show these small changes as visible pulsing.
- Utility voltage regulation. Utilities adjust voltage on their lines as demand changes. This is normal within limits.
- A loose neutral or connection that worsens as wires cool and contract at night.
- Failing LED drivers that strobe as they overheat or age.
If several brands of bulbs on different circuits pulse together, and neighbors see it too, report it as a power quality issue. If it is one bulb or one fixture, replace the bulb or have the fixture checked.
What is voltage drop and when is it a problem?
Voltage drop is the loss of voltage along a wire as current flows through it. Longer wires, smaller wires, and heavier loads mean more drop. Some drop is unavoidable. It becomes a problem when lights dim noticeably as loads come on, motors run hot, or electronics reset.
Utilities have standards they must meet at the point where power is delivered to you:
- Texas: The PUCT rule on power quality, 16 TAC 25.51, requires utilities to keep distribution voltages within the limits of the current ANSI C84.1 standard. The rule incorporates that standard by reference rather than printing the numbers, and it requires utilities to have and use monitoring instruments to investigate customer power quality complaints.
- Florida: Florida PSC rule 25-6.046 says voltage at the point of delivery shall not be more than 5% above or below the utility's adopted standard voltage. For a 120-volt standard, that is about 114 to 126 volts. The rule excludes variations caused by service interruptions or weather.
Voltage drop inside your home, on your wiring past the meter, is your responsibility. Long runs to detached garages, shops, pool equipment or docks are common trouble spots. See subpanels for garages and additions.
Who do I call for flickering lights, the utility or an electrician?
Use this rule: widespread flicker goes to the utility first; confined flicker goes to an electrician.
Texas: call your wires company, not your retail provider
In deregulated parts of Texas, including Houston and Dallas-Fort Worth, you pay a retail electric provider, but a separate delivery company owns the poles, wires and meter. Oncor's FAQ puts it plainly: Oncor delivers electricity but is not a retailer. For flicker, voltage and equipment problems, contact the delivery company:
| Area | Who handles voltage and lines | Contact we verified |
|---|---|---|
| Dallas-Fort Worth and much of North and West Texas | Oncor | 888-313-4747 (outages, 24/7); 888-313-6862 (general and service requests) |
| Houston | CenterPoint Energy | Use the number on CenterPoint's website; we could not load it for this guide |
| Parts of South and West Texas | AEP Texas; TNMP in some areas | Use the utility's website or your bill |
| Austin | Austin Energy (city-owned) | Report outages through Austin Energy; 512-322-9100 for downed lines |
| San Antonio | CPS Energy (city-owned) | 210-353-HELP (4357) for electric emergencies; 210-353-2222 for power quality investigations |
Florida
Florida utilities both sell and deliver power, so call your utility directly: FPL (1-800-4-OUTAGE), Duke Energy Florida, Tampa Electric (TECO), JEA in Jacksonville, or your city utility or electric co-op. Use the number on your bill for numbers we did not verify.
What to tell them
- When it happens (time of day, weather, what was running).
- Whether neighbors see it.
- Whether lights get brighter, not just dimmer.
- Any damage you can see to the service drop, weatherhead or meter.
If the utility tests and finds its voltage is within limits, hire a licensed electrician to check your service equipment and panel. See reporting to utilities and hiring an electrician.
Flickering after a storm or after the power comes back
Flicker that starts right after a storm or a long outage deserves attention. Wind and falling limbs can loosen the service drop or damage the weatherhead and meter box, and a loose connection there can cause flicker or a partial outage. During Winter Storm Uri in 2021, Oncor reported finding transformers damaged when they had to power back up large amounts of load after controlled outages ended. Damaged utility equipment can deliver unstable voltage even after service returns.
Steps: look (from a distance) at the wire to your house, the weatherhead and the meter box. Report damage or ongoing flicker to the utility. Keep sensitive electronics unplugged until voltage looks stable. If customer-owned parts are damaged, a licensed electrician must repair them before the utility reconnects. See hurricane electrical safety and whole-house surge protection.
Renters
If flicker is confined to your unit, tell your landlord in writing and do not open switch boxes or the panel. Flicker with warm switches or a burning smell is a safety condition. Texas Property Code 92.052 and Florida Statutes 83.51 set landlords' repair duties. See landlord and tenant electrical.
Can flickering lights mean a fire hazard?
Sometimes. Flicker from a loose connection is a heat source. The worse the connection, the more heat. Warning signs that move flicker from annoying to urgent:
- Warm or discolored switch plates or outlet covers.
- Buzzing, crackling or sizzling from a switch, fixture or the panel.
- A fishy or hot-plastic smell.
- A breaker that has started tripping on that circuit.
- Flicker in a home with aluminum branch wiring. CPSC says the aluminum-wiring fire hazard happens at connections.
Any of these means turn off the circuit and call an electrician. Smoke or heat in a wall means leave and call 911.
How to choose a provider
- Decide: one bulb, one fixture, one room, or the whole house?
- Tighten or replace the flickering bulb; try a different brand.
- Match dimmable LEDs to an LED-rated dimmer and check the compatibility list.
- Do not put smart bulbs on a dimmer.
- Ask a neighbor if they see flicker too.
- If lights get brighter when appliances start, unplug electronics and call the utility.
- In deregulated Texas, report voltage and line problems to the wires company (TDU), not the retail provider.
- Report tree limbs on lines; never trim near lines yourself.
- Call an electrician for room-level flicker, warm switches, buzzing or burning smells.
- Write down when flicker happens and what was running before you call.
Related electricians guides
- Why Is the Power Out in Half My House (and What Do I Do)?
- How do you choose and install recessed and LED lighting the right way?
- What electrical work does a smart home need, and who is allowed to do it?
- How do I report a power outage in Texas or Florida?
- Meter, Meter Base, Service Drop: What Does the Utility Fix and What Do You Pay For?
- Burning Smell From an Outlet, Panel or Light: What to Do Right Now
- AC and Heat Pump Electrical Problems: Tripping Breakers, Disconnects, Capacitors, GFCI Rules and Who to Call in Texas and Florida
Electricians by state and city
Questions people ask
Why do my lights flicker?
The cause depends on how widespread it is. One bulb usually means a loose or failing bulb or a dimmer mismatch. One fixture or room points to a loose connection on that circuit. The whole house points to the service connection, the meter base, a loose neutral, or utility equipment. A brief dip when the AC starts is normal. Lights that get brighter when something turns on are a warning sign of a neutral problem.
Can flickering lights mean a fire hazard?
They can, when the cause is a loose connection. CPSC warns loose wire connections and worn switches can arc and overheat. Watch for warm switch plates, buzzing, crackling, a fishy or burning smell, or a breaker that has started tripping. If you notice any of these, turn the circuit off and call an electrician. Smoke or heat in a wall means leave the home and call 911.
Is whole-house flickering a utility problem?
Often. Ask a neighbor on the same transformer whether they see it too. If yes, report it to the utility. In deregulated Texas that is the delivery company, such as Oncor or CenterPoint. If the utility finds its side is fine, the problem may be in your meter base, main panel connections or main breaker, which a licensed electrician must repair.
Who do I call for flickering lights, the utility or an electrician?
Widespread flicker across the house, flicker in wind, or flicker neighbors see too: call the utility first. Flicker in one room or on one circuit: call an electrician. Lights that get brighter when appliances run: call the utility right away, then an electrician if needed. Utilities in Texas and Florida must meet voltage standards and investigate power quality complaints.
What voltage should my house have?
Most homes are served at a nominal 120/240 volts. Florida rule 25-6.046 requires delivery voltage within 5% of the utility's standard voltage, which for 120 volts is about 114 to 126 volts. Texas rule 16 TAC 25.51 requires utilities to stay within ANSI C84.1 limits. Readings outside the normal band, or a big difference between the two legs, should be reported to the utility.
Why does one LED bulb flicker but not the others?
Usually the bulb or its driver is failing, the bulb is loose, or it is a different brand or type than the others on the same dimmer. Swap it with a bulb from a fixture that works. If the problem follows the bulb, replace it. If the problem stays in the socket, the socket or fixture connection may be loose and should be checked with the power off.
Sources
- CPS Energy: Power Quality FAQs
- 16 Tex. Admin. Code 25.51, Power Quality
- Fla. Admin. Code R. 25-6.046, Voltage Standards
- Oncor: Outage FAQs
- Oncor: After the Storm (2026)
- Austin Energy: How We Restore Power
- FPL: Make sure you're ready to safely receive power
- CPSC Home Electrical Safety Checklist, Pub. 513 (July 2008)
- CPSC: Repairing Aluminum Wiring, Pub. 516
- Texas Property Code ch. 92
- Florida Statutes s. 83.51
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


