New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Foundation repair contractors

What Is a Foundation Elevation Survey, and How Do You Read Floor Level Readings?

A floor elevation survey measures how high or low each part of your floor sits compared with one reference point. Here is how the readings are taken, how to read the map, the math engineers use, and why one survey alone cannot prove your foundation is moving.

A foundation elevation survey is a set of relative height readings taken across your floor, usually every few feet, measured against one reference point and drawn as a map with contour lines. Engineers use it to calculate tilt and deflection and compare them with tolerances such as the L/360 deflection ratio in the Texas Section ASCE guidelines. One survey shows the floor's shape on one day only. It cannot show movement unless it is compared with an earlier survey.

Key facts

  • The Texas Section ASCE residential guidelines (Version 3, 2022) make relative floor elevations and a scaled elevation drawing the defining feature of a Level B foundation investigation.
  • Version 3 requires the drawing or report to say whether different floor covering thicknesses were considered and how built-in slopes, such as sunken rooms or shower areas, were handled.
  • The guidelines state that a single floor level survey yields the shape of the foundation at one instant and may not be enough to support a conclusion.
  • Deflection ratio is the largest gap between a third point and a straight line between two points, divided by the distance (L) between the two points.
  • The guidelines use L/360 as an analogous deflection limit for a residential foundation, borrowed from the International Residential Code floor member limit.
  • A foundation tilt greater than 1 percent is usually noticeable, and the Americans with Disabilities Act treats a 2 percent slope as too large (ASCE Texas guidelines).
  • The guidelines caution against judging floor deviations over distances under about 20 feet because built-in unevenness can dominate.
  • Texas Section ASCE guidelines call for a post-repair floor elevation survey, with a copy furnished to the client.
  • Florida's sinkhole statute, 627.706(2)(k), ties structural damage partly to floor or foundation displacement beyond acceptable variances in ACI 117-90, ACI 318-95 or the Florida Building Code.

What is a foundation elevation survey?

A foundation elevation survey, also called a floor level survey or relative elevation survey, is a grid of height readings taken across the finished floor of a house. Each reading tells you how much higher or lower that spot is than one chosen reference point. The readings are then drawn on a floor plan, usually with contour lines that connect points of equal height, the same way a hiking map shows hills and valleys.

The survey answers one narrow question: what shape is the floor in right now? It does not, by itself, tell you why the floor has that shape or whether it is still changing. That is why engineers treat it as one piece of evidence, combined with cracks, door fit, brick lines and the history of the house.

In Texas, the Texas Section of the American Society of Civil Engineers (ASCE) publishes Guidelines for the Evaluation and Repair of Residential Foundations, now in Version 3 (adopted in 2022). The guidelines are not law and say so plainly. They are an aid for engineers, but they are the most common reference Texas engineers point to when they explain what a floor survey should include and how to judge it. The Texas Board of Professional Engineers and Land Surveyors also refers readers to the Texas Section ASCE for residential foundation documentation.

Relative elevation vs absolute elevation

A floor survey almost always measures relative elevation. The surveyor picks a reference point inside the house, often a spot near the middle or a corner that looks stable, and calls it zero. Every other reading is plus or minus inches from that point. A reading of -1.2 means that spot is 1.2 inches lower than the reference.

Absolute elevation is height above a fixed datum, such as sea level. That is what a land surveyor measures for a flood elevation certificate. A foundation survey does not need absolute elevation, because what matters is how parts of the floor compare with each other. Do not confuse the two. A flood elevation certificate will not tell you whether your slab is bent, and a floor level survey will not tell you your flood zone height.

How are the readings taken?

The surveyor walks a grid through the house and records a reading at each point. Points are commonly spaced every several feet, with extra readings near corners, along exterior walls, at areas of cracking, and anywhere the floor feels off. The ASCE Texas guidelines do not set a fixed spacing. They ask for elevations "in sufficient detail to represent the shape of the foundation or floor adequately."

Common tools

ToolHow it worksStrengthsLimits
Digital fluid level (altimeter-style)A base unit sits at the reference point, connected by a fluid-filled hose to a handheld sensor that reads height difference directlyFast, one person can do it, works around corners and through roomsMust be calibrated and kept at stable temperature; hose must not be kinked
Water level or manometerA clear tube filled with water; water seeks the same level at both ends, so you measure from the water line to the floorCheap, simple physics, no batteriesSlow, air bubbles cause errors, needs two people
Rotating laser levelA laser sweeps a level plane; a rod or receiver measures distance from the beam to the floorAccurate in open roomsNeeds a line of sight, so many setups in a chopped-up floor plan
Optical level (builder's level) and rodTraditional survey instrument on a tripodProven, accurate over distanceLine of sight needed; slower indoors

Whatever the tool, the ASCE Texas guidelines say the engineer should consider the precision of the measuring device when reporting results. A survey that reports readings to a hundredth of an inch with a tool that is only good to a tenth is giving false precision.

Floor coverings change the numbers

The survey measures the top of the finished floor, not the top of the concrete. A room with 3/4-inch hardwood over a pad will read higher than an adjoining room with thin vinyl, even if the slab under both is perfectly flat. Tile set on a mortar bed can add even more. Version 3 of the ASCE Texas guidelines responded to this by requiring the scaled drawing or report to state whether different floor covering thicknesses were considered and, if so, what adjustments were applied.

If you are reading a survey and see a sudden one-inch step at a doorway between carpet and tile, check whether the report adjusted for flooring before you assume the slab dropped.

Built-in slopes

Some areas are built low on purpose: garage slabs, shower pans, sunken living rooms, and the step-down at an exterior door. The guidelines ask the report to explain how these built-in slopes were handled. Good surveys either leave those areas out of the deflection math or mark them clearly.

How do I read a foundation elevation map?

Most reports include a floor plan with each reading written at its location and contour lines drawn at a fixed interval, often every half inch or quarter inch. Here is how to read one in five steps.

  1. Find the reference point. It is usually marked 0.0 or with a symbol. Every other number is relative to it.
  2. Find the high and low points. The spread between the highest and lowest readings is the total elevation difference. This number gets quoted a lot, but on its own it does not tell you much, because it ignores distance.
  3. Look at the contour pattern. Tight, closely spaced lines mean the floor changes height quickly over a short distance. Wide spacing means a gentle slope.
  4. Look for a shape. A high middle with lower edges is often called a dome or center-lift pattern. Low middle with high edges is a dish or edge-lift pattern. One corner far lower than the rest suggests a localized drop. A steady slope from one side to the other is tilt.
  5. Find the axis lines. The guidelines say the drawing should show the lines along which deflection and tilt were calculated. If no axis lines are shown, ask the engineer how the numbers were figured.

Common shapes and what they may suggest

Map patternWhat it can indicateWhat to ask
Center high, perimeter lowPerimeter soil drying and shrinking (common in Texas clay in drought), or center heave from a plumbing leak or trapped moistureWas plumbing tested? Are there trees or poor drainage on the low side?
Perimeter high, center lowEdge heave after wet weather on expansive clay, or settlement under the interiorHas rainfall or irrigation changed? Is the low area near a bathroom or kitchen?
One corner lowLocalized settlement, often near a tree, downspout, or poorly compacted fillWhere do the downspouts discharge? Any large trees within reach of the corner?
Steady slope across the houseTilt, which may be from original construction or from movementDo brick mortar lines and window sills slope the same way?
Irregular, patchy readingsFlooring changes, built-in slopes, or measurement errorWere floor coverings adjusted for?

These patterns are clues, not diagnoses. On expansive clay, both upward movement (heave) and downward movement (settlement) can produce similar-looking maps. See settling vs structural damage and expansive clay soil in Texas for why the cause matters.

Tilt and deflection: the math, with a worked example

Engineers turn the readings into two numbers: tilt and deflection. The ASCE Texas guidelines define both.

Tilt

Tilt is "the planar variation from a level condition to one that slopes across the entire foundation." In plain English, the whole slab leans one way like a tabletop with short legs on one side. Tilt is usually given as a percent: inches of drop divided by inches of distance, times 100.

Example: The front wall of a house reads 0.0 and the back wall, 50 feet away, reads -3.0 inches, with a steady slope between. Fifty feet is 600 inches. 3.0 divided by 600 is 0.005, or 0.5 percent tilt. The guidelines say tilt over 1 percent is usually noticeable and the ADA treats 2 percent as too steep. So 0.5 percent may not be felt underfoot.

Deflection

Deflection is bending, not leaning. The guidelines define the deflection ratio as "the maximum deviation of a third point from a straight line between two points divided by the distance (L) between the two points."

Worked example:

  1. Pick two points on a line across the house, 40 feet apart. Point A reads 0.0 and point B reads -0.6 inches.
  2. Draw an imaginary straight line from A to B. Halfway along, that line would sit at -0.3 inches.
  3. The actual reading at the halfway point is -1.8 inches. The deviation from the straight line is 1.8 minus 0.3, or 1.5 inches.
  4. Convert L to inches: 40 feet is 480 inches.
  5. Deflection ratio = 1.5 / 480 = 1/320, written L/320.
  6. Compare with the L/360 limit. The limit for a 480-inch span is 480 / 360 = 1.33 inches. A 1.5-inch deviation is a little over that limit.

A bigger number under the L means a flatter floor. L/600 is stiffer than L/360. L/200 is worse.

What the guidelines say the number means

The ASCE Texas guidelines borrow L/360 from the International Residential Code, which limits live-load deflection of structural floor members to L/360. They treat the whole foundation as one member and differential soil movement as the load. Then they give three cases:

  • If the profile shows deflection under L/360, it is unlikely the foundation is materially deflected unless visible signs say otherwise.
  • If deflection is over L/360 but there are minimal symptoms, the engineer needs more information before concluding anything.
  • If deflection is over L/360 and there are sufficient symptoms (cracks, binding doors, sloping brick lines), the engineer is generally justified in finding excessive deflection.

So the number alone does not decide the case. In the example above, a house at L/320 with tight doors and no cracking might still be judged acceptable after more information is collected.

Overall vs localized deflection

Overall deflection uses the full length of the foundation in one direction. Localized deflection looks at a smaller area. The guidelines say localized deflection may be more common, but they caution against evaluating floor deviations over distances shorter than about 20 feet, because the normal unevenness built into a slab can dominate over short spans. If someone shows you a 1-inch dip over 6 feet and calls it failure, ask how built-in unevenness was ruled out.

Why one elevation survey does not prove movement

This is the most misunderstood point about floor surveys. Slabs are not poured perfectly level. The ASCE Texas guidelines say foundations "are generally constructed with surface elevation differences" and warn engineers to be cautious about assuming any particular construction tolerance. We did not find a single published as-built tolerance number in the sources we reviewed that applies to every Texas or Florida house, so treat any claim like "all new slabs are within half an inch" as something to ask the source for.

A single survey is a snapshot. The guidelines say it "yields the shape of the foundation at one instant and may or may not furnish sufficient information to support a conclusion." If a house reads 2 inches out of level today, you cannot tell from that survey alone whether it was built 1.5 inches out and moved half an inch, or built flat and moved 2 inches, or has not moved at all.

How engineers get around this

  • Original Construction Elevations (OCE). Some builders or buyers have a survey done soon after the slab is poured, before first closing. The guidelines call this an OCE survey. When one exists, the engineer subtracts today's reading from the OCE reading at each point to get the actual change, after adjusting both surveys to a common reference point and for flooring differences.
  • Repeat surveys. Surveys done months or years apart, at the same points, show change over time. This is how you measure a rate of movement.
  • Other evidence. Brick coursing that is not level, door alignment, the levelness of countertops, sills and trim, and cracking patterns all help the engineer estimate how much of today's unevenness was built in.

The practical lesson: if you buy a house, keep your inspection-period survey. If you build a house, ask for an OCE survey. A baseline costs little next to the arguments it can settle later, whether with a seller, a builder, a repair company or an insurer.

What reading difference is considered bad?

There is no single magic number of inches. A 2-inch difference across a 70-foot house is a very different thing from a 2-inch difference across 12 feet. That is why engineers use ratios (tilt percent and deflection ratio) instead of raw inches.

MeasureReference point in the ASCE Texas guidelinesPlain meaning
Deflection ratioL/360 analogous limitUnder it: unlikely to be materially deflected unless symptoms say otherwise
TiltOver 1 percent usually noticeable; 2 percent considered too large under the ADAComfort and use of the building
Short-span dipsCaution under about 20 feetBuilt-in unevenness may explain them
Wall or veneer tiltWeight falling outside the middle third of the bearing area causes tension in masonryA structural integrity concern

Insurers and lawyers sometimes use different thresholds than engineers. In Florida sinkhole claims, for example, "structural damage" in Fla. Stat. 627.706(2)(k) includes interior floor displacement or deflection beyond acceptable variances in ACI 117-90 or the Florida Building Code that makes the interior unfit for service or a safety hazard, and foundation displacement beyond ACI 318-95 or Florida Building Code variances with specified strength consequences. That legal test is narrower than "the floor is out of level." See Florida sinkhole insurance coverage.

Who does elevation surveys in Texas and Florida?

Texas

Under the ASCE Texas guidelines, the floor survey is part of a Level B investigation by a Texas-licensed professional engineer. Level A is a first-impressions walk-through. Level B adds relative elevations, a scaled drawing, and a comparison of overall deflection, localized deflection and tilt with tolerances. Level C adds testing, such as soil sampling, plumbing tests, material testing, a reinforcing steel survey or post-tension cable testing.

TREC-licensed home inspectors must give a written opinion on foundation performance and report indicators such as sloping floors under 22 TAC 535.228, but they are not required to determine the cause of a condition. The Texas engineering board (TBPELS) has said that analyzing the cause of a foundation condition or recommending repairs is the practice of engineering. Some inspectors take floor readings as extra information. That is useful, but it is not an engineering evaluation.

Foundation repair companies also take readings, often during a free estimate. Those readings can be accurate, but the person reading them has a stake in the outcome. See structural engineer foundation inspections and questions to ask a salesperson vs an engineer.

Florida

Florida does not use the Texas ASCE guidelines, but floor surveys play a role in sinkhole investigations. Under Fla. Stat. 627.7072, the engineer and geologist must perform tests sufficient, in their professional opinion, to determine whether there is a sinkhole loss and to recommend repair. The Florida Geological Survey notes that consultants may use ground-penetrating radar, electrical resistivity surveys and soil borings to look for cavities. A floor survey helps show whether the building meets the structural damage definition. The FGS also says licensed home inspectors and insurance adjusters are not qualified to determine whether sinkhole activity is present. Licensed professional geologists or engineers are. See the Florida sinkhole claim process.

What does an elevation survey cost?

We found no official or government price list for floor surveys. Most homeowners get one as part of an engineer's evaluation. This Old House, in an Oct. 8, 2026 update based on Angi market research, puts a structural engineer report at $500 to $1,000 and a geotechnical soil report at $500 to $3,000. Prices vary with house size, how many readings are taken, and whether a written report and scaled drawing are included.

When comparing quotes, ask whether the price includes:

  • A scaled drawing with contour lines and axis lines
  • Flooring adjustments and a note on built-in slopes
  • Calculated tilt and deflection compared with tolerances
  • The engineer's opinion of cause, not just numbers
  • A post-repair survey if you go ahead with repairs

Can I do my own floor level survey?

Yes, you can take your own readings, and doing so is a good way to keep a baseline between professional visits. Your readings will not carry the weight of an engineer's survey in a dispute, but they can show you whether something is changing.

DIY water level method

  1. Buy about 30 to 50 feet of clear vinyl tubing and fill it with water, working out every air bubble. A few drops of food coloring make the water line easier to see.
  2. Tape one end upright to a fixed object at your reference point, such as a door frame in the middle of the house. Mark the water line on a ruler taped next to it.
  3. Carry the other end to each test point. Hold a tape measure on the floor and read the distance from floor to water line.
  4. Subtract each reading from the reference reading. A larger floor-to-water distance means that spot is lower.
  5. Write every reading on a sketch of your floor plan. Date it.
  6. Mark the exact spots (a dot of paint on baseboard, or a measured distance from two walls) so you can repeat them later.

Limits of a DIY survey

  • Air bubbles, kinks and temperature changes in the tube throw readings off.
  • Reading a tape to better than about an eighth of an inch is hard by eye.
  • Flooring thickness differences will show up as false steps.
  • You are measuring the floor's shape, not the cause. Cause takes an engineer.

A simpler check is a long straightedge or a 4-foot level laid across a room, with a marble test as a quick red flag. These tell you a floor is out of level, but not by how much across the whole house.

How do surveys work as repair, contract and warranty evidence?

Elevation surveys are the main way to prove what a repair did. The ASCE Texas guidelines say remediation documents should include existing floor elevations or contours, elevation adjustment requirements if any, and a requirement for a floor elevation survey after the work is done. They say the post-repair measurements should be made by the engineer or an authorized representative, kept on record, and given to the client.

The guidelines also set expectations: "It is unlikely that elevation adjustments will result in a level foundation." Underpinning part of a structure will not improve the parts that were not underpinned. If a contract promises a perfectly level floor, ask the engineer of record whether that is realistic.

Before and after: what to keep

  • The pre-repair survey with date, tool used and reference point
  • The engineer's repair plan showing pier or pile locations
  • The post-repair survey at the same points
  • Any letter of substantial completion from the engineer
  • Later surveys at the intervals the warranty requires

Many repair warranties are triggered only if movement exceeds a set amount. Without a baseline survey taken right after repair, you cannot show the threshold was crossed. Read the warranty's exact wording on how movement is measured. See lifetime and transferable foundation warranties and what to expect during foundation repair.

Plumbing after a lift

If a repair includes jacking or lifting, the guidelines say water supply and sanitary drain lines should be tested for leaks and any leaks repaired. A change in slab shape can stress pipes. Ask for those test results along with the post-repair survey.

How often should I re-survey after repair?

We found no rule in Texas or Florida law that sets a re-survey schedule for houses. The interval is usually set by the engineer's recommendation or the warranty. Common sense points:

  • Get the post-repair survey right after the work, before furniture and flooring hide anything.
  • Re-survey after the first full wet and dry season. On Texas clay, soil moisture swings between summer drought and wet months, so a reading in August and one in March can differ even without a problem.
  • Re-survey if new cracks appear, doors start binding again, or a plumbing leak is found.
  • Survey at the same time of year each time if you can, so seasonal swing does not look like failure.
  • Use the same reference point and the same points every time.

Do new homes need an elevation survey?

Yes, if you can get one. The ASCE Texas guidelines describe Original Construction Elevations as surveys done soon after foundation construction and before first closing. Having one turns every later survey into a true measure of movement. Without it, any later dispute starts with a guess about how flat the slab was poured.

In Texas, builder disputes over slab defects run through the Residential Construction Liability Act (Property Code chapter 27), which requires written notice and evidence such as expert reports before suit. In Florida, chapter 558 sets a pre-suit notice process. An early survey can be key evidence in both. See Texas new construction slab defects and Florida chapter 558 defect claims.

How to choose a provider

  • Ask who will take the readings and whether a Texas or Florida licensed PE will interpret them
  • Confirm the tool used and its stated precision
  • Make sure the report names the reference point and marks it on the drawing
  • Check that floor covering differences and built-in slopes are noted and adjusted
  • Look for axis lines and calculated tilt and deflection, not just high and low numbers
  • Ask for an OCE survey on new construction before closing
  • Keep every survey with date and point locations in one folder
  • Require a post-repair survey in any repair contract
  • Re-survey at the same season and points each time
  • Take your own dated water-level readings between professional surveys
  • Pair surveys with a crack photo log and door-fit notes

Related foundation repair contractors guides

Foundation repair contractors by state and city

Questions people ask

What reading difference is considered bad on a floor survey?

No single inch value applies to every house. Engineers convert readings into tilt percent and deflection ratio. The Texas Section ASCE guidelines use L/360 as a deflection reference: below it, a foundation is unlikely to be materially deflected unless visible signs say otherwise. Tilt over 1 percent is usually noticeable. A raw high-to-low number of, say, 2 inches means little until you know the distance between the points and whether flooring changes were adjusted.

Can a foundation be 2 inches out of level and be fine?

It can. Slabs are built with some unevenness, and the ASCE Texas guidelines warn against assuming a set construction tolerance. Across a 60-foot house, 2 inches of steady tilt is about 0.28 percent, below the 1 percent level that is usually noticeable. What matters is the deflection ratio, whether the shape is changing over time, and whether there are symptoms such as cracks and binding doors.

Do floor coverings affect elevation readings?

Yes. Surveys measure the top of the finished floor. Hardwood, tile on mortar, carpet and vinyl all have different thicknesses, so a doorway between two floor types can show a false step. Version 3 of the ASCE Texas guidelines asks the report to state whether flooring differences were considered and what adjustments were made. If yours does not say, ask.

Who should do a foundation elevation survey?

For a decision about repair, a licensed professional engineer or the engineer's authorized representative, with the engineer interpreting the results. In Texas this is a Level B evaluation under the ASCE Texas guidelines. Repair companies and some home inspectors also take readings. Those can be useful data, but in Texas analyzing the cause or recommending repairs is engineering under Occupations Code chapter 1001.

How long does a floor level survey take?

For a typical single-family house, the readings themselves usually take an hour or two on site, depending on size, layout and the number of points. The written report with a scaled drawing and calculations takes longer. Ask the engineer for a delivery date when you book. If you are in an option or inspection period, tell them the deadline.

Can I use my survey from when I bought the house?

Yes, and you should. An earlier survey becomes a baseline. Give it to your engineer so the new readings can be compared point by point. For the comparison to be fair, both surveys need to be adjusted to a common reference point and for any flooring changes made since. Repeat readings at the same locations when possible.

Will an elevation survey find a plumbing leak?

Not directly. A survey can show a high spot or low spot near a bathroom or kitchen that makes an engineer suspect a leak, but finding a leak takes plumbing testing. The ASCE Texas guidelines list plumbing testing as part of a Level C investigation and call for leak testing after any lift. See our page on plumbing leaks under slab foundations.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration