Local Guide · Foundation repair contractors
How Do You Repair a Pier-and-Beam Foundation? Shimming, Re-Leveling, Rot and Crawl Spaces
A neutral guide to shimming, adding piers, sistering joists, sill replacement and crawl space moisture control, with Texas and Florida code, inspection, termite and historic-district rules.
Pier-and-beam foundations are repaired by shimming beams on existing piers, adding or replacing piers, strengthening or sistering framing, replacing rotted sills and beams with treated lumber, and controlling crawl space moisture, the categories listed in the ASCE Texas repair guidelines. Costs run roughly $2,000 to $15,000 (Fixr, January 2026). Fix drainage and moisture first, use an engineer for new supports on clay, and check city permits and historic rules.
Key facts
- ASCE Texas guidelines (2022) list shimming, framing repair, added or replaced supports, re-established void space and crawl space moisture control as pier-and-beam repairs.
- ASCE Texas guidelines say hardwood or steel shims may be used atop pier caps, and treated lumber is recommended for framing repairs.
- IRC R408.2 (2021 Houston Residential Code; 2023 FBC Residential) requires 1 sq ft of vent per 150 sq ft of crawl space, or 1/1,500 with a Class I vapor retarder.
- Code decay protection applies where joists are within 18 inches, girders within 12 inches, or wood columns within 8 inches of exposed ground (R317.1).
- TREC inspectors need not enter crawl spaces with under 18 inches of headroom or access smaller than 24 by 18 inches (22 TAC 535.228).
- Houston uses a Repair Per Spec list for level-and-shim or minor beam replacement and City Engineer Details for block-and-base repairs within limits.
- San Antonio requires a Certificate of Appropriateness for all exterior modifications and repairs on historic-overlay properties.
- Fixr (January 2026) lists pier-and-beam foundation repair at $2,000 to $15,000.
- Florida WDO inspection reports must list inaccessible areas and visible damage (Fla. Stat. 482.226).
How is a pier-and-beam foundation built, and what goes wrong?
A pier-and-beam house sits on a raised wood floor instead of a concrete slab poured on the ground. From the ground up, the parts are:
- Footings and piers: concrete pads, blocks, brick or concrete columns spaced under the house. Older Houston homes often sit on "block and base" supports: a concrete base with stacked concrete masonry blocks on top.
- Beams (girders): heavy timbers resting on the piers.
- Sills: the wood members resting on the perimeter foundation wall or beam.
- Joists: smaller framing members that span between beams and carry the subfloor.
- Crawl space: the open area under the floor.
You see this type across older neighborhoods in Houston, Dallas, Fort Worth, Austin and San Antonio, and in older homes in North Florida and the Panhandle. It has one big advantage over a slab: you can get under it. Plumbing, wiring and the framing itself can be inspected and repaired without breaking concrete.
Common causes of sagging, bouncy or uneven floors
- Soil movement under piers. On Texas expansive clay, individual piers rise and drop with soil moisture. A pier near a thirsty tree may sink in a drought while one near a leaking downspout heaves.
- Undersized or overspanned framing. Joists or beams spanning too far between supports sag over time.
- Wood rot. Wet crawl spaces, poor ventilation and wood too close to the soil lead to decay in sills, beam ends and joists.
- Termites and other wood-destroying insects.
- Failed shims. Softwood shims crush, rot or slip out.
- Past repairs gone wrong. Loose stacked blocks, wood posts on bare dirt, or jacks left in place.
- Loads added later. A heavy tile floor, a bathtub, or a removed wall can overload framing.
Not every sag is a foundation problem. A floor can dip because a joist cracked while the piers are fine. Sorting out which part failed is the first job of any inspection. See signs of foundation problems and pier-and-beam vs slab.
How do you repair a pier-and-beam foundation?
The ASCE Texas Section's repair guidelines (Version 3, 2022) list four main repair categories for pier-and-beam foundations: shimming the floor framing atop existing supports, repairing or strengthening the framing, replacing or adding supports, and re-establishing void space. They also list crawl space moisture control: cross ventilation, under-floor drainage, ground clearance for beams and joists, and treated lumber.
| Repair | What it fixes | What it involves |
|---|---|---|
| Shimming (level and shim) | Gaps between beams and pier caps; minor unevenness | Jacking beams slightly and driving hardwood or steel shims on top of pier caps |
| Adding piers or beams | Spans that are too long; sag between supports | New footings and piers, or a new beam under sagging joists |
| Replacing piers | Cracked, leaning or sinking piers; loose block stacks | Temporary support, removal, new footing and pier, often deeper on clay |
| Deep piers under perimeter or interior beams | Persistent settlement on clay | Pressed concrete piles, steel piers or drilled piers, per engineer design |
| Sistering joists | Cracked, notched or sagging joists | Fastening a new full-length member alongside the old one |
| Sill and beam replacement | Rotted or termite-damaged sills and beam ends | Temporary shoring, cutting out bad wood, installing treated lumber |
| Crawl space moisture control | Rot, mold, high humidity | Grading and drainage, vents, vapor retarder, or a sealed (unvented) crawl space |
ASCE recommends treated lumber for general framing repairs and says any added supports should be compatible with the original foundation support system. Mixing a deep pier under one beam with shallow blocks everywhere else can create its own uneven movement, which is why an engineer's layout matters.
What is shimming, and are steel shims better than wood?
Shimming means lifting a beam just enough to slide thin wedges or plates between the beam and the top of the pier, then letting the beam back down onto them. It is the most common and least expensive pier-and-beam adjustment. Houston's permitting center even has its own category, "Level and Shim and/or Minor Beam Replacement," which uses a Repair Per Spec list instead of full engineered drawings.
Steel vs wood shims
| Shim type | Pros | Cons |
|---|---|---|
| Hardwood | Cheap, easy to fit, recognized by ASCE Texas guidelines | Can crush or rot if the crawl space stays wet; must be dense hardwood, not soft scraps |
| Steel | Will not crush or rot; recognized by ASCE Texas guidelines | Can corrode in persistently wet crawl spaces; must be sized and seated properly |
| Softwood scraps, roofing shingles, stacked junk | None worth having | Crush, slip and decay; a sign of a poor past repair |
The ASCE guidelines name both hardwood and steel shims as acceptable. The bigger quality questions are whether the shim stack is stable, whether it sits fully on the pier cap, and whether the pier under it is sound.
How often does a pier-and-beam house need re-leveling?
There is no fixed interval, and we found no neutral source that sets one. On stable soil with a dry crawl space, a well-shimmed house may go many years without adjustment. On active Texas clay, seasonal swings can loosen or tighten shims within a few years, especially after a severe drought followed by heavy rain. Many repair contracts include one or more "adjustments" within a set period; read what the warranty actually promises. See foundation warranties.
A sensible rhythm: check the crawl space after major weather swings, and have floor elevations measured when doors start sticking again. Track the numbers over time so you know whether the house is cycling with the seasons or steadily dropping. See foundation elevation surveys.
How do you fix rotted sills, beams or joists?
Rot repair is carpentry done under a loaded floor, so the sequence matters:
- Find the moisture source. Leaking plumbing, a downspout emptying at the wall, soil piled against siding, or a crawl space that floods. Fixing wood without fixing water just schedules the next repair.
- Probe the damage. Rot and insect damage often extend beyond what you can see. A screwdriver pushed into the wood shows soft areas.
- Shore the floor. Temporary jacks or cribbing carry the load while bad wood is removed.
- Cut out and replace rotted sill or beam sections with treated lumber, or sister new joists alongside damaged ones.
- Re-set the floor onto permanent supports and shims.
- Treat for insects if they were involved, with a licensed pest control company.
Wood clearance rules worth knowing
The residential code requires decay protection, by naturally durable or preservative-treated wood, in crawl spaces where wood joists or the bottom of a wood floor are closer than 18 inches to exposed ground, where wood girders are closer than 12 inches, and where wood columns are closer than 8 inches (IRC R317.1, as adopted in the 2021 Houston Residential Code). If your crawl space is shallow, replacement framing near the ground should be treated lumber.
Termites and pier-and-beam homes
Termites can damage sills, joists and beams in both states, and a raised floor with a damp crawl space is an inviting place for them. When buying or selling, the wood-destroying insect report is a separate document from the home inspection.
- Texas: The Texas Department of Agriculture's Structural Pest Control Service says the Official Texas Wood Destroying Insect Report, form SPCS/T-5, was released in September 2019 and replaced the SPCS/T-4 version. TDA licenses and regulates pest management professionals.
- Florida: Fla. Stat. 482.226 requires wood-destroying organism (WDO) inspection reports on a department-prescribed form from a licensee or qualified representative. The report must list visible accessible areas not inspected and why, inaccessible areas, visible evidence of previous treatments or infestations, and any organisms and visible damage found. A WDO report is not a guarantee that no organisms are present unless it says so, and licensees must carry errors and omissions insurance or a bond of at least $500,000 aggregate and $250,000 per occurrence.
- New construction in Florida: the Florida Residential Code (R318.1) requires termite protection and a certificate of compliance from the licensed pest control company.
Tip: if a WDO or WDI report lists "areas not inspected" under the house, that gap matters for a pier-and-beam home. Ask whether the crawl space was actually entered.
Crawl space ventilation, vapor barriers and encapsulation
Moisture is the slow killer of pier-and-beam framing. The residential code gives two paths for under-floor spaces (section R408 in both the 2021 Houston Residential Code and the 2023 Florida Building Code, Residential):
Path 1: a vented crawl space
- Net vent area of at least 1 square foot for each 150 square feet of under-floor area.
- One vent within 3 feet of each exterior corner.
- Vent openings covered with corrosion-resistant mesh, grates or similar, with openings no larger than 1/4 inch.
- If the ground is covered with an approved Class I vapor retarder, total vent area may drop to 1/1,500 of the floor area, and corner vents can be replaced by cross ventilation.
Path 2: an unvented (sealed) crawl space
- Exposed earth covered with a continuous Class I vapor retarder, seams overlapped 6 inches and sealed or taped, edges run at least 6 inches up the stem wall and sealed.
- Plus one of: continuous mechanical exhaust of 1 cfm per 50 square feet with an air path to the house and insulated perimeter walls; conditioned air supply at the same rate with a return path; use as a code-compliant plenum; or, in the Florida code, dehumidification sized to the manufacturer's specifications.
Other crawl space rules
- Access: floor openings at least 18 by 24 inches; perimeter wall openings at least 16 by 24 inches (R408.4).
- Debris: vegetation, organic material, wood forms and construction scraps removed (R408.5). Old form boards left under a house attract termites.
- Groundwater: where water can rise within 6 inches of the floor at the perimeter, or surface water doesn't drain, the crawl space grade must be as high as the outside grade unless an approved drainage system is provided (R408.6).
- Flood zones: walls enclosing the under-floor space need flood openings, and the inside ground must be at or above outside grade on at least one side (R408.7).
Do crawl spaces need a vapor barrier in Texas?
Not always. Under R408, a vented crawl space meeting the 1/150 rule does not require a ground vapor retarder. A vapor retarder becomes required if you choose the sealed path, and it lets you reduce vent area on the vented path. Whether encapsulation makes sense depends on your groundwater, drainage and climate. In humid Houston and Florida, a sealed crawl space without dehumidification or conditioned air can trap moisture. Check which code edition your city has adopted before you design anything.
What do Texas home inspectors check under a pier-and-beam house?
Texas real estate inspectors follow TREC's Standards of Practice, 22 TAC 535.228. For foundations, the inspector must:
- Give a written opinion on the performance of the foundation.
- Report the foundation type and the vantage point from which the crawl space was inspected.
- Report as Deficient deteriorated materials; deficiencies in beams, joists, bridging, blocking, piers, posts, pilings, columns, sills or subfloor; and crawl space ventilation or drainage that is not performing.
But the inspector is not required to enter a crawl space with less than 18 inches of headroom or an access opening smaller than 24 inches wide by 18 inches high. If the report says the crawl space was viewed "from the access opening," much of the framing may not have been seen.
A TREC inspector also may not give an engineering opinion on a foundation, such as the cause of a condition or a repair design, unless he or she also holds a professional engineer license (TBPELS Policy Advisory Opinion 43, 2018). For cause and repair design, hire an engineer. See foundation inspection and structural engineers and Texas real estate foundation inspections.
Permits and historic districts in Houston, San Antonio and Florida
Houston permit categories
Houston's foundation repair permit page splits pier-and-beam work into tiers:
- Level and shim and/or minor beam replacement: submit a completed Repair Per Spec list.
- Block and base foundation within city engineered limits: submit the City Engineer Detail (block and base with 4x8 or 4x6 beams) plus a site-specific foundation plan or layout.
- Block and base beyond those limits: plans and details prepared by a Texas-licensed engineer.
Houston also requires pre-construction and final inspections and, in mapped flood zones, a floodplain development permit with a sealed cost estimate or notarized contract plus an appraisal.
Historic districts: Houston Heights and San Antonio
Houston's Office of Preservation says it reviews Certificates of Appropriateness for new construction, demolition and alterations to historic structures in historic districts and landmarks. Its exemption sheet (Jan. 2021) lists ordinary maintenance and repair and alterations not visible from the street as exempt, while exterior changes visible from the street are regulated. Leveling and shimming hidden under the house is likely maintenance, but raising a house, changing skirting, or altering the visible foundation could be treated differently. Ask before work starts: historicpreservation@houstontx.gov or 832-393-6556.
San Antonio's Office of Historic Preservation says all exterior modifications and repairs for properties with a historic zoning overlay require a Certificate of Appropriateness, including side and rear yards not readily visible from the street. Minor projects can usually be approved by staff; others need a public hearing before the Historic and Design Review Commission. Work started without approval can bring a stop work order and a $500 post-work application fee. Contact OHP at 210-207-0035.
Florida
Florida requires a permit to repair a building (Fla. Stat. 553.79), with only ordinary minor repairs that do not cut or remove a structural beam or load-bearing support eligible to skip one, and only with building official approval. Florida law defines a foundation, beams and floors as structural components, and work on them falls to a general, building or residential contractor (Fla. Stat. 489.105(15), 489.113(3)(a)). Many Florida cities with historic districts also run design review; check your city's preservation office. See permits by city and Florida licensing.
What does pier-and-beam repair cost?
Published ranges are wide because "pier-and-beam repair" can mean anything from a half-day of shimming to rebuilding the whole support system.
| Source and date | Item | Range |
|---|---|---|
| Fixr, updated Jan. 27, 2026 | Pier-and-beam foundation repair | $2,000 to $15,000 |
| Bob Vila, updated May 29, 2024 | Pier-and-beam foundation repair | $700 to $25,000 |
| This Old House, Oct. 8, 2026 (Angi data) | Piering or underpinning, per pier | $1,000 to $3,000 |
| This Old House, Oct. 8, 2026 | Structural engineer report | $500 to $1,000 |
| This Old House, Oct. 8, 2026 | Foundation labor, about | $200 per hour |
None of these sources publish Texas- or Florida-specific pier-and-beam figures. What pushes your price up or down:
- Shimming only versus new piers, deep piers or new beams.
- How much rot or termite damage is found once the crew is under the house. Get a unit price for extra sill or joist replacement in the contract.
- Crawl space height. Low crawl spaces mean slow, hand work.
- Whether plumbing must be re-supported or repaired after leveling.
- Permits, engineer letters and historic review.
- Moisture control: drainage, vents, vapor retarder or encapsulation equipment.
For full cost detail, see foundation repair cost.
Can I shim a pier-and-beam house myself?
Small shimming jobs are sometimes done by handy owners, but the risks are real: a house on a jack can shift or fall, over-lifting cracks plaster and tile and pulls plumbing apart, and soft or poorly seated shims fail. Low crawl spaces add confined-space, wildlife and wiring hazards.
If you do any work yourself, keep it to inspection and moisture control: clearing debris, fixing gutters and grading, and noting where shims are loose. In Houston, even level-and-shim work is listed as a permit category; check before starting. In Florida, the owner-builder exemption lets owners act as their own contractor on their own one- or two-family home, with a presumption of a violation if the home is sold or leased within one year of completion (Fla. Stat. 489.103(7)). See DIY foundation work.
How to choose a provider
- Look for moisture sources first: plumbing leaks, downspouts, grading, standing water in the crawl space.
- Ask the inspector whether the crawl space was entered or viewed from the opening.
- Get floor elevations measured and kept on file.
- Hire an engineer if piers are sinking, new supports are needed, or the soil is expansive clay.
- Get a written scope: shims, piers, beams, sills, joists, moisture control.
- Get unit prices for extra rot repair found once work begins.
- Confirm shim material (hardwood or steel) and treated lumber for replacements.
- Check permits and, in Houston Heights or San Antonio historic districts, preservation approval.
- Get a WDI (Texas) or WDO (Florida) report if termites are suspected.
- Choose a vented or sealed crawl space design that meets R408.
- Ask about plumbing checks after leveling.
- Keep the warranty, pier map and engineer letter for resale.
Related foundation repair contractors guides
- Slab vs Pier-and-Beam Foundations: What Is the Difference, and Which Holds Up Better?
- How Much Does Foundation Repair Cost in Texas and Florida? Real Price Ranges by Method
- What Is a Foundation Elevation Survey, and How Do You Read Floor Level Readings?
- What Does a Structural Engineer Foundation Inspection Cost, and What Do You Get?
- Expansive Clay Soil and Your Foundation: Why Do Texas Homes Move?
- Do You Need a Permit for Foundation Repair? City-by-City Rules in Texas and Florida
- Lifetime Transferable Foundation Warranties: What They Cover and What They Don't
- DIY Foundation Repair: What Can Homeowners Safely Do Themselves, and What Should They Never Try?
Foundation repair contractors by state and city
Questions people ask
How do you repair a pier-and-beam foundation?
Repairs fall into four groups listed in the ASCE Texas guidelines: shimming beams on existing piers, repairing or strengthening framing, replacing or adding supports, and re-establishing void space. Most jobs also need moisture control, such as better drainage, vents or a vapor retarder. A good repair starts by finding why the floor moved, whether soil, rot, termites or overloaded framing, and an engineer should design any new supports on expansive clay.
What is shimming a pier-and-beam house?
Shimming means lifting a beam slightly with a jack and placing thin hardwood or steel wedges or plates between the beam and the top of the pier, then lowering the beam onto them. It closes gaps and levels minor dips. Houston lists level-and-shim work as its own permit category using a Repair Per Spec list. Shims only work if the pier under them is sound, so cracked or sinking piers must be replaced first.
How often does a pier-and-beam house need re-leveling?
No neutral source sets a fixed schedule. On stable soil with a dry crawl space, shims can hold for many years. On active Texas clay, a drought followed by heavy rain can loosen or tighten shims within a few years. Watch for doors that start sticking again, check the crawl space after big weather swings, and compare floor elevation readings over time. Many repair warranties include a limited number of adjustments; read the terms.
What does pier-and-beam repair cost?
Fixr (updated January 2026) lists pier-and-beam foundation repair at $2,000 to $15,000, and Bob Vila (May 2024) lists $700 to $25,000. This Old House (October 2026) puts new piers at $1,000 to $3,000 each and an engineer's report at $500 to $1,000. No source we found publishes Texas- or Florida-only figures. Rot found after work starts, low crawl spaces and permits all add cost, so ask for unit prices.
What causes sagging floors in pier-and-beam homes?
Common causes include piers sinking or heaving with clay soil moisture, joists or beams spanning too far, rotted sills and beam ends from a wet crawl space, termite damage, crushed or slipped shims, and heavy loads added later, like tile or a tub. Sometimes the piers are fine and a single cracked joist is the problem. An inspection under the house should sort out which part failed before anyone prices a repair.
How do you fix rotted sills or joists?
First stop the water, whether from a leak, a downspout, or soil against the siding. Then the crew shores up the floor, cuts out rotted wood, replaces sills or beam sections with treated lumber, and sisters new joists alongside damaged ones. The floor is set back onto supports and shims. If termites were involved, a licensed pest control company should treat. Code requires decay-resistant wood near the ground in crawl spaces.
Should I add piers or beams under a sagging floor?
If the sag is between supports because the framing spans too far, adding a beam or more piers can fix it. The ASCE Texas guidelines say added supports should be compatible with the original support system, so a single deep pier among shallow blocks can create uneven movement. In Houston, block-and-base supports within city limits can use City Engineer Details; anything beyond those limits needs Texas-licensed engineer plans.
What is a steel shim vs a wood shim?
Both are acceptable under the ASCE Texas guidelines. Hardwood shims are inexpensive and easy to fit but can crush or rot if the crawl space stays damp. Steel shims will not crush or rot but can corrode in wet conditions and must sit fully on the pier cap. Avoid softwood scraps, roofing material or loose stacks; those are signs of a poor repair that will need redoing.
How do I ventilate or encapsulate a crawl space?
Under code section R408, a vented crawl space needs at least 1 square foot of vent per 150 square feet of floor, with a vent within 3 feet of each corner. With a Class I vapor retarder on the ground, vent area can drop to 1/1,500. A sealed crawl space needs a sealed Class I vapor retarder plus mechanical exhaust, conditioned air, or (in Florida's code) a sized dehumidifier. Fix drainage first.
Do crawl spaces need a vapor barrier in Texas?
Not necessarily. Under R408 as adopted in the 2021 Houston Residential Code, a vented crawl space meeting the 1-per-150 rule does not require a ground vapor retarder. A Class I vapor retarder is required for a sealed crawl space, and it lets a vented crawl space use less vent area. Cities adopt different code editions, so confirm with your local building department before you design or buy a system.
Can termites damage a pier-and-beam foundation?
Yes. Termites can attack sills, joists and beams, especially in damp crawl spaces or where wood touches soil. In Texas, the official wood destroying insect report is TDA form SPCS/T-5. In Florida, WDO reports under Fla. Stat. 482.226 must list inaccessible areas, evidence of past treatment and any visible damage. Check whether the inspector actually went under the house, because inaccessible areas are where hidden damage often sits.
Can I do pier-and-beam shimming myself?
Some owners do small shimming jobs, but working under a jacked house is dangerous, over-lifting cracks finishes and stresses plumbing, and poor shims fail. Houston lists level-and-shim work as a permit category, so check before starting. Safer owner tasks are clearing crawl space debris, fixing gutters and grading, and noting loose shims for a pro. Any new piers or beams on clay should follow an engineer's plan.
Sources
- ASCE Texas Section, Guidelines for the Evaluation and Repair of Residential Foundations, Version 3 (2022)
- 2021 Houston Residential Code, Chapter 4 Foundations (R408) (UpCodes)
- 2021 Houston Residential Code, Chapter 3 (R317) (UpCodes)
- Florida Building Code, Residential 2023, Chapter 4 Foundations (R408) (UpCodes)
- Florida Building Code, Residential 2023, Chapter 3 (R318) (UpCodes)
- 22 Tex. Admin. Code 535.228 (LII)
- TBPELS Policy Advisory Opinion 43 (2018)
- Houston Permitting Center, Foundation Repair
- Houston Planning and Development, Historic Preservation
- Houston Office of Preservation, What's Exempt from Regulation (Jan. 2021)
- San Antonio Office of Historic Preservation, Before Getting Started
- Texas Department of Agriculture, Structural Pest Control Service
- Fla. Stat. 482.226 (2025)
- Fla. Stat. 553.79 (2025)
- Fla. Stat. 489.105 (2025)
- Fla. Stat. 489.103 (2025)
- Fixr, Cost of Foundation Repair (updated Jan. 27, 2026)
- Bob Vila, Foundation Repair Cost (updated May 29, 2024)
- This Old House, How Much Does Foundation Repair Cost? (updated Oct. 8, 2026)
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


