Local Guide · Home alarm and security systems
Door and Window Sensors, Motion Detectors and Glass-Break Sensors: What to Install and Where
How each sensor type works, where burglars actually get in, how many sensors a house needs, where not to put them, and what Texas and Florida rules and hurricane glass mean for your choices.
Door and window contact sensors are the core of a home alarm because they watch the openings burglars use. Motion detectors add a second layer inside, and glass-break sensors cover big panes. Place sensors on every ground-level entry first, follow the maker's placement rules, and test them. Pet and hurricane glass need extra checks.
Key facts
- A U.S. Bureau of Justice Statistics report (Victimization During Household Burglary, September 2010) puts household burglaries at about 3.7 million per year on average for 2003 to 2007.
- The same BJS report says damaging or removing a door was the most common type of entry in forcible and attempted forcible entry burglaries.
- BJS reports that in 40% of unlawful (no force) entries into unoccupied residences, the offender got in through an unlocked door or window, and in 17% through an open door or window.
- BJS reports that burglars attempting forcible entry tampered with door handles or locks more often when no one was home (30%) than when someone was (19%).
- A Santa Barbara County Sheriff's Office CPTED guide advises that all windows should have locks and that sliding glass doors should have a lock with an additional locking pin, and that door locks be at least 40 inches from adjacent windows.
- Houston Police advise securing all sliding glass doors with an anti-lifting device and a secondary locking device, and using a double cylinder deadbolt if there is glass within 40 inches of the lock.
- Tex. Prop. Code 92.153 requires a Texas rental to have a window latch on each exterior window and a pin lock and a handle latch or security bar on each sliding glass door, at landlord expense.
- Fla. Stat. 489.529 allows a monitoring company to skip the call-to-confirm step if the alarm has a properly operating visual or auditory sensor that lets monitoring staff verify the signal.
- Texas bars an alarm company from installing, on or after January 1, 2007, a control panel that does not meet or exceed American National Standards Institute standards for false alarm reduction (Tex. Occ. Code 1702.287).
What are door and window contact sensors?
A contact sensor is the most common burglar alarm part. It has two pieces: a small magnet and a switch. One piece goes on the door or window, and the other on the frame, close together. When the door or window opens, the pieces separate. The switch changes state, and the panel sees an open "zone." If the system is armed, the alarm sounds and a signal goes to the monitoring center.
Common types
- Surface-mount. Stuck or screwed on the face of the door and frame. Easy to add and easy to see.
- Recessed. Small round pieces set into drilled holes in the edge of the door and the frame. Neater, but drilling is needed. A better fit for new construction or a remodel.
- Wired or wireless. A wired contact connects to the panel by a thin cable. A wireless contact has a small battery and a radio. See wired vs wireless security systems.
- Overhead door contacts. Heavier versions made for garage doors that swing or roll and may shift a little. They need a wider gap tolerance.
- Vibration or shock sensors. Small sensors that sense taps or hits on a window or door. They can be used where a magnetic contact does not fit, such as a fixed pane or a door with a metal frame.
Why door sensors come first
Contact sensors give an early warning at the opening itself, before anyone is inside. A Bureau of Justice Statistics (BJS) report on household burglary, Victimization During Household Burglary (September 2010), says damaging or removing a door was the most common type of entry in forcible and attempted forcible entry burglaries. That is why doors are a priority. See the entry data section below.
A contact sensor tells the alarm that an opening moved. It does not tell the alarm that a window was cracked, a pane was cut, or a lock was picked, as long as the sash did not move. That is why contacts are paired with other sensors in a layered system.
Do I need motion detectors if I have door sensors?
A good alarm has layers. Door and window contacts form the perimeter. Motion detectors form the interior layer. They answer different questions:
| Layer | What it catches | What it misses |
|---|---|---|
| Door and window contacts | An opening that moves, at the moment it moves | Entry through a pane that is broken without moving the sash; entry through an opening you did not protect (such as a pet door or a skylight) |
| Glass-break sensors | The sound or shock of glass breaking in a room | Entry through an open or unlocked window; glass types that do not shatter the usual way |
| Interior motion detectors | Movement inside a protected room | Someone who is outside; or a person who moves out of the detector's field of view |
If you only want one layer, use contacts on every ground-level entry. If you want a second layer, add motion detectors in the paths a burglar would use after getting in: a main hallway, the living area that connects to the entry doors, and the room with your most valuable items. If you have a pet, see the pet section below.
Armed modes
Most panels have "away" and "stay" modes. In "away," contacts and motion detectors are all on. In "stay," interior motion is off so you can move around at home while doors and windows are still protected. Learn both. Many false alarms come from arming "away" while a person or pet is still inside, or from a motion sensor left on in "stay."
BJS said in the same 2010 report that offenders gained unlawful entry through an unlocked door or window in 40% of unlawful entries into unoccupied homes. A contact sensor cannot lock the door for you. Locks matter as much as sensors. See smart locks, deadbolts and door hardware.
Are pet-immune motion sensors reliable?
A pet-immune motion sensor is a motion detector set to ignore movement from animals below a size or weight. It usually combines infrared sensing with software that decides whether the movement looks like a person. The maker states a pet size limit on the box or spec sheet. We did not find a named, independent test of how well these sensors perform, so we cannot rate their reliability. Do not treat the label as a guarantee.
What to check before you buy
- The maker's maximum pet weight, written on the spec sheet. Compare it to your biggest pet when full-grown.
- How the pet weight rating changes if the sensor is mounted at a different height. Many makers give a mounting height and ask you to keep the sensor within it.
- Whether the maker says the sensor works if a pet jumps onto furniture. If your cat or dog climbs a sofa back or a counter, the detector may see it as a person-sized heat source.
Practical steps
- Mount at the height the manual says, and aim it where pets rarely walk or climb.
- Run a "walk test" (see below) while your pet moves around, with the account on test, to see what triggers the sensor.
- If your pet keeps triggering the sensor, use "stay" mode when you are home and consider contacts only on doors and windows when you leave, along with glass-break sensors.
- Skip motion detectors in rooms where a pet will have the run of furniture. Use contacts and a glass-break sensor there instead.
- Tell the monitoring center you have pets. It can help them judge a signal.
False alarms from pets are a main cause of city fees. See the false alarm section below and false alarms in Texas and Florida.
What is a glass-break sensor, and does it work on laminated or hurricane glass?
A glass-break sensor listens for the sound of breaking glass or feels the shock of the break. There are two main types:
- Acoustic. A small microphone that listens for the sound patterns glass makes when it breaks. It is mounted on a wall or ceiling and can cover a room, as far as its maker says.
- Shock (vibration). A small sensor stuck on the glass itself or on the frame, which feels a hit or a break.
Makers list the range, the glass types and the sizes the sensor is made for. Use those. We could not load UL's own pages (they returned an access error), so we did not read the UL standards for intrusion detection units and we do not describe their test methods here.
Laminated, tempered and impact-rated glass
Laminated glass has a plastic layer between two panes. Impact-rated glass, as used in hurricane areas, is built to stay in place when struck by debris. FLASH, a nonprofit focused on safe homes, says impact-rated glass is always in place, which is its main advantage over shutters, and that compliance should appear on a label or sticker on the product or in paperwork showing it meets the relevant testing standards.
Because laminated and impact-rated glass is made to resist breaking apart, an acoustic glass-break sensor tuned to the sound of ordinary glass shattering may behave differently on it. We did not find a named test, standard or manufacturer data that we could load describing how glass-break sensors perform on laminated or impact glass, so we cannot say. The honest answer is: do not assume. Ask the sensor's maker, in writing, whether the model is rated for laminated or impact-rated glass of your pane size and thickness. If the answer is no, protect those openings with contacts on the frame and a shock sensor made for that glass, and consider interior motion as a backup.
Where glass-break sensors are most useful
- Rooms with large windows or glass doors where a contact on the frame would not detect a smashed pane.
- Sliding glass doors and doors with glass within reach of the lock. Houston Police advise a double cylinder deadbolt if there is glass within 40 inches of the lock, and a Santa Barbara County Sheriff's CPTED guide says door locks should be at least 40 inches from adjacent windows. A sensor adds a second layer there.
- Ground-level rooms away from the front door, such as a back bedroom or a rear sunroom.
Glass-break sensors also help verify an alarm. Under Fla. Stat. 489.529, a Florida monitoring company must try to confirm a monitored intrusion alarm by call, text or other electronic means before asking law enforcement to respond, but not if the alarm has a properly operating visual or auditory sensor that lets the monitoring staff verify the signal. This is the statute's exception for sensors that give monitoring staff a way to verify. It does not name glass-break sensors, so ask your provider how verification works on your system.
Which entry points do burglars use most?
We looked for current, named, dated data. Here is what we could load, and its limits.
What the BJS report says
The BJS report Victimization During Household Burglary (September 2010) uses National Crime Victimization Survey data for 2003 to 2007 and reports about 3.7 million household burglaries per year on average. It says:
- Damaging or removing a door was the most common type of entry in forcible and attempted forcible entry burglaries.
- In 40% of unlawful (no force) entries into unoccupied residences, offenders got in through an unlocked door or window, and in 17% through an open door or window.
- Among attempted forcible entries, burglars were more likely to tamper with door handles or locks when no one was home (30%) than when someone was home (19%).
The text version of the report we loaded does not break down front door versus back door versus garage, and it leaves out most tables, so we do not give those percentages. We also could not load the FBI's Crime in the United States burglary pages (the site returned an access error), so we do not quote FBI shares of forcible versus unlawful entry here. The BJS data is also more than ten years old, so it describes a past period. Treat it as a pattern, not a prediction for your home.
What police and sheriff guides say
Houston Police's burglary prevention brochure says to secure all sliding glass doors with an anti-lifting device and a secondary locking device, to use a double cylinder deadbolt if there is glass within 40 inches of the lock, to pin hinges on exterior doors with outside hinges, and to use latches and secondary locks on windows. The Florida Sheriffs Association's burglary prevention page advises locking all windows and sliding doors, using track locks or a solid rod or dowel in the sliding door track, and securing the door between the garage and the house.
| Entry point | Why it matters | Sensor to consider |
|---|---|---|
| Front door | Doors are the most common entry in forced entries (BJS) | Contact on the door, plus a motion detector in the entry hall |
| Back and side doors | Often out of view from the street | Contact on each door; lighting and camera |
| Sliding glass doors | Large glass area; lock can be defeated if not secured | Contact; glass-break or shock sensor; a track bar or pin lock |
| Ground-floor windows | Unlocked windows were part of 40% of unoccupied unlawful entries (BJS) | Contact on each window that opens; glass-break sensor in big rooms |
| Garage entry door and overhead door | Garage door openers are not locks, according to the Santa Barbara County Sheriff's Office guide | Contact on the interior entry door; overhead door contact |
| Upper-floor windows and balconies | Trees, roofs and ladders can give access (Houston PD advises pruning trees so a thief cannot reach a second floor window) | Contact on windows with outside access |
How many sensors does a typical house need?
No standard number exists. We did not find a statute or standard that sets a minimum. The right number depends on your home's openings. Use this simple method:
- Count every exterior door that can be opened, including the door from the garage into the house and any sliding door. Each gets a contact.
- Count every ground-floor window that opens. Most alarm planners give each a contact, unless the window is painted shut or small and high. Fixed panes do not need a contact, but large ones may need glass-break coverage.
- Add upper-floor windows reachable from a roof, balcony, tree, porch cover or ladder.
- Add the overhead garage door if it opens into the house or is not otherwise guarded.
- Choose interior motion locations that cover the main routes from entry doors into the home.
- Choose glass-break coverage for rooms with large glass areas.
Example (illustrative only, not a standard)
| Home | Entry points | Contacts | Motion | Glass-break |
|---|---|---|---|---|
| 1-story, 3 bedrooms | 2 exterior doors, 1 sliding door, 1 garage entry door, 9 windows | 4 doors plus up to 9 windows | 1 to 2 in main route | 1 for the living room with large panes |
| 2-story, 4 bedrooms | 3 exterior doors, 1 sliding door, 14 windows (6 reachable from a porch roof) | 4 doors plus ground windows plus the 6 reachable windows | 2 to 3 | 1 to 2 |
| Small apartment or condo | 1 entry door, 1 balcony door, 4 windows | 2 doors; windows only if ground-level or reachable | 1 | 0 to 1 |
This table is a worked example to show the counting method. It is not data. If the cost matters, you can protect the openings that matter most first: doors, then ground-level windows, then others. See home security system cost in Texas and Florida and the pre-purchase checklist.
Where should sensors not go?
Every sensor maker publishes mounting rules. Follow them exactly. Many false alarms come from ignoring them. We did not find a named standard we could load that sets universal "do not mount here" distances for motion detectors, so we describe the common types of problems and tell you to check the manual for numbers.
Motion detectors
- Do not aim at windows and direct sunlight. Sun can heat surfaces and change what the sensor sees.
- Keep away from heat and air sources. Heating and air vents, space heaters, fireplaces, water heaters, ceiling fans, curtains that move in a draft and cooking appliances can trigger a sensor.
- Keep away from moving objects. Plants, hanging items and balloons can cause false alarms.
- Do not hide behind furniture. Boxes, cabinets and tall shelves block the view.
- Respect the mounting height. Too high or low can create blind spots or let pets in the zone.
- Do not put them in garages or sunrooms with big temperature swings unless the maker says the model is made for that.
Door and window contacts
- Keep the gap between magnet and switch within the maker's limit. Doors and windows can shift with heat and humidity. Texas and Florida summers can swell wood frames.
- Do not mount the sensor where a hurricane shutter closes over it or where paint, caulk or weatherstrip covers it.
- Check that the contact is rated for steel doors and frames if yours are steel. Ask the maker.
- Keep the contact away from strong magnets and electronics that interfere.
Glass-break sensors
- Place within the range and line of sight stated by the maker.
- Do not mount near kitchens, bathrooms or noise sources such as speakers or loud appliances. They can cause false triggers.
- Heavy curtains or blinds may block sound; ask the maker how to handle them.
The comparison with smoke alarms is useful. The CPSC says not to place a smoke alarm near a kitchen appliance or fireplace, and to avoid locating alarms near bathrooms, heating appliances, windows or ceiling fans, because these cause nuisance alarms. See smoke alarms and fire detection. Burglar sensors follow a similar logic, but each has its own rules.
What causes sensor false alarms, and what do they cost in Texas and Florida?
Most false alarms are caused by people and equipment, not by crime. Common causes:
- Arming "away" with a pet or person still inside.
- A door not fully latched, or a door that swells or warps.
- Low or dead sensor batteries (check your panel screen).
- Loose mounts or contacts that slipped out of alignment.
- Heat, sunlight, drafts, ceiling fans or plants near motion detectors.
- Insects or spiders on or inside sensor lenses.
- Storm effects such as lightning, wind and power flickers. See alarm backup in power outages and hurricanes.
- User errors with codes, especially a visitor, cleaner or repair person who does not know the code.
Rules and costs
Texas ties false alarm reduction to equipment. A Texas alarm company may not install, on or after January 1, 2007, any alarm system with a control panel that does not meet or exceed the standards of the American National Standards Institute for false alarm reduction (Tex. Occ. Code 1702.287). The statute does not name a specific number; ask the installer to show how the panel meets it. A Texas alarm company must also give the occupant written information on how to prevent false alarms and how to operate the system (1702.286(a)). Under 1702.134(c), a city may require discontinuance of an alarm device that, due to mechanical malfunction or faulty equipment, causes at least five false alarms in 12 months, until it is repaired. False alarms from human error or acts of God do not count as malfunctions for that purpose.
Florida requires a monitoring company to try to confirm an alarm by call, text or other electronic means before asking police to respond (Fla. Stat. 489.529), with exceptions such as a working visual or auditory sensor that lets staff verify the signal.
City fees are set locally and change, so confirm each figure on the city's page.
| City | What the city's loaded page says (confirm before relying) |
|---|---|
| Houston | Residential burglar alarm permit holders get 3 free false alarms per preceding 12 months, then $50 each for the 4th and 5th, $75 each for the 6th and 7th, and $100 each after that. City documents conflict on some amounts, so check the page. |
| Dallas | A service fee applies to each false burglar alarm notification beyond three in a 12-month period. We could not date the city notice we loaded. |
| San Antonio | Permitted burglar alarms: 1 to 3 free, 4 to 5 at $50, 6 to 7 at $75, 8 or more at $100. The city page blocks automated readers, so confirm on sa.gov. |
| Austin | $220 for each police response to a non-permitted alarm location, and a Class C misdemeanor fine of $75 for a first occurrence and $100 for each later one. |
| Miami | First two false alarms in a permit year are not invoiced; the 3rd through 6th are invoiced and can lead to suspension; the 7th or more can lead to revocation. |
| Tampa | The city police page says alarm permits are not required to be filed with the City of Tampa; it focuses on false alarm reduction. |
| Orlando | Residential: 1 to 3 no fine, 4 to 6 at $50 each, 7 or more at $100 each in 12 months; unregistered alarm $50 per activation. |
| Jacksonville | 1st and 2nd no charge, 3rd $50, 4th $100, 5th $150, 6th $250; at the 7th and later JSO stops responding to burglar alarms and charges $250 per false alarm. |
For each city's rules, see Houston, Dallas, San Antonio, Austin, Miami, Tampa, Orlando and Jacksonville.
How do hurricane shutters and impact glass affect sensor placement?
The National Weather Service says the Atlantic hurricane season runs June 1 to November 30 and that, over a typical two-year period, the U.S. coastline is struck by an average of 3 hurricanes, 1 of which is major (winds of 111 mph or greater). Many Florida and Gulf Coast homeowners add opening protection. That changes how you place sensors.
- Shutters cover the sensor. FLASH says shutters must be deployed before a storm and that impact glass stays in place. A contact mounted on the window sash is behind the shutter when it is closed, and the shutter itself may not be wired. If you want protection while shutters are closed, ask whether the shutter can have its own sensor, or rely on interior motion.
- Motor-operated roll-down shutters can often be closed remotely, FLASH notes, and homeowners should learn how to open them manually during a power outage. They also need to be left clear of sensors.
- Impact glass is not break-proof. FLASH says it stays in place, but a burglar can still force it with time and tools. Pair contacts with a shock sensor made for the glass, and confirm the model with the maker.
- Emergency plywood. FLASH says temporary plywood panels carry no testing or approval. A contact may be unusable behind them.
- Sensors on frames. Contacts on the door or window frame can survive being behind shutters if the shutter does not press on them.
Florida's My Safe Florida Home program can fund certain wind-mitigation improvements, including opening protection, after an inspection. We could not load the program's rules for this page. Check the official program site for current eligibility and amounts before you plan on a grant. Fla. Stat. 627.0629 requires insurers' rate filings to include discounts for fixtures or construction techniques that reduce windstorm loss, including opening protection, but it does not cover burglar alarm discounts. Alarm discounts are set by each insurer. See insurance discounts for home security systems.
What do UL standards say about these sensors (UL 639, UL 634)?
You may see "UL listed" on sensor packaging. UL is a safety testing organization, and its standards describe how products are tested. We tried to load UL's pages and a general standards listing and were blocked or got no useful text, so we did not read the standards. We cannot describe what UL 639 or UL 634 require, what they test, or what they do not test. We could not verify their scope or titles from a primary source in this research, so we treat both as unverified. Check UL's own standards catalog for the current title and scope.
What to do as a buyer: ask the seller for the model number and listing number, and look up the listing in the testing organization's public database. A listing is not a promise about how the sensor will perform in your house. Placement, installation, power and signal path matter at least as much. Also, Florida's smoke detection rules for single-family rentals mention listing by Underwriters Laboratories, Factory Mutual or another nationally recognized testing laboratory (Fla. Stat. 83.51(2)(b)), and Texas requires smoke alarms in rentals to be tested and listed by Underwriters Laboratories, Factory Mutual Research Corporation or United States Testing Company (Tex. Prop. Code 92.254(a)). Those are for smoke alarms, not burglar sensors.
Texas and Florida rules on sensors for owners, renters and landlords
Texas rental security devices
Tex. Prop. Code 92.153 says a Texas landlord, without a tenant request and at the landlord's expense, must provide a window latch on each exterior window, a doorknob lock or keyed deadbolt on each exterior door, a pin lock and a handle latch or security bar on each sliding glass door, and a keyless bolting device and door viewer on each exterior door. Section 92.154 sets deadbolt height (no lower than 36 inches and no higher than 48 inches from the floor for new installations) and a throw of at least one inch for deadbolts installed on or after September 1, 1993. Those are locks and latches, not electronic sensors. The statute does not require landlords to install alarm sensors. Under 92.163, security devices installed under the subchapter become fixtures, and a tenant may not remove, change or rekey them without the landlord's permission. See Texas tenant security device rights.
Florida rentals
Fla. Stat. 83.51(2)(a)2 says that unless otherwise agreed in writing, the landlord of a dwelling other than a single-family home or duplex must make reasonable provisions for locks and keys. A Florida tenant must not destroy, deface, damage, impair or remove any part of the premises or landlord property (83.52(6)). A tenant who wants to add a door or window contact should ask in writing and prefer adhesive, removable sensors. See Florida landlord and tenant security and entry and renters' security options.
Owners and DIY installs
Texas's alarm licensing chapter does not apply to a person installing an alarm on their own property or to sales made only by e-commerce, over the counter or by mail order (Tex. Occ. Code 1702.328). In Florida, the sale or installation of finished products that do not become a permanent fixed part of the structure is exempt from the alarm contractor part (Fla. Stat. 489.503(5)), and an owner may do some work on their own single-family or duplex home under conditions (489.503(6)(a)). Local permit rules may still apply to wiring. See permits and codes for alarm installation and DIY vs professional home security.
HOAs and condos
In Texas, an HOA may not adopt or enforce a covenant that prevents an owner from installing security measures such as a security camera, motion detector or perimeter fence, with exceptions (Tex. Prop. Code 202.023). Florida's loaded HOA and condominium statutes contain no sensor or camera provisions, so check your documents. See Texas and Florida.
How to test and maintain your sensors
- Call the monitoring center and put the account on test. Tell them you are testing sensors.
- Walk-test motion detectors. Many panels have a "walk test" mode. Walk through the protected area and see when the sensor registers. It will tell you where blind spots are and whether pets trigger it.
- Open every door and window contact. With the system armed, open each one and confirm the panel shows that zone and the monitoring center gets it. Do not forget the garage entry door.
- Test glass-break sensors only with the maker's test tool or procedure. Do not break glass.
- Check batteries and signal. Read the panel's sensor status screen for low-battery or weak-signal messages.
- Clean and check. Dust and insects can block lenses. Make sure the magnet and switch are tight and aligned.
- Record the test. Date, who you spoke to, and results.
Do this after any remodel, repainting, door replacement, pet change or furniture move. For a full schedule, see alarm system maintenance, testing and battery replacement. Doors and windows without working locks cannot be fixed by a sensor, so walk the house and fix locks first.
Questions to ask before you buy sensors
- Is each sensor supervised (does the panel notice if it goes silent or its battery is low)?
- What is the pet weight rating on the motion sensor, and at what mounting height?
- Is the glass-break sensor rated for my pane type, size and thickness, including laminated or impact-rated glass?
- What is the sensor's listed model number and listing?
- Are the contacts rated for steel doors, overhead doors or my window frames?
- How will sensors work with my hurricane shutters or impact windows?
- What does a replacement sensor cost, and is it covered by my contract?
- Who is licensed in Texas (DPS) or Florida (DBPR) to install or service it? See how to check an alarm company license.
For a bigger picture of how these parts fit into a full system, see how home security systems work and outdoor lighting, landscaping and home hardening.
How to choose a provider
- List every exterior door, sliding door, garage entry door and ground-level window that opens.
- Put a contact sensor on every ground-level door first, then on windows that open.
- Check locks on every door and window before you rely on sensors.
- Add motion detectors along the path from entry doors into the home, within the maker's mounting rules.
- Check the pet weight rating and mounting height if you have pets, and run a walk test.
- Ask the glass-break sensor maker in writing whether the model works on laminated or impact-rated glass.
- Do not aim motion detectors at windows, heat sources, vents or ceiling fans.
- Plan sensor locations together with any hurricane shutters or impact glass.
- Test every sensor with the monitoring center, and again after remodels or pet changes.
- Check sensor battery and signal status on the panel at least once a month.
Related home alarm and security systems guides
- Smart Locks, Deadbolts and Door Hardware: What Actually Improves Security
- Wired vs Wireless Home Security Systems: Reliability, Cost and Hurricane Performance
- False Alarms in Texas and Florida: Causes, Fines and How to Prevent Them
- Outdoor Lighting, Landscaping and Home Hardening: What Police and Researchers Recommend
- How Does a Home Security System Work?
- Alarm System Maintenance: Testing, Batteries, Lifespans and Troubleshooting
- Indoor and Outdoor Security Cameras: Types, Placement, Storage Math and Legal Limits in Texas and Florida
- Home Security for Renters in Texas and Florida: What You Can Install and What the Landlord Must Provide
Home alarm and security systems by state and city
Questions people ask
What are door and window contact sensors?
A contact sensor has a magnet and a switch, one on the door or window and one on the frame. When the opening moves, the pieces separate and the panel sees an open zone. If the system is armed, the alarm sounds and a signal goes to the monitoring center. Contacts can be wired or wireless, surface-mount or recessed.
Do I need motion detectors if I have door sensors?
Contacts protect the openings; motion detectors protect the inside. If a burglar gets in without moving a contact, such as through a broken pane or an unprotected opening, motion can still catch movement. Use contacts first, then add motion along the main routes in the home. Use stay mode at home so motion does not trigger.
Are pet-immune motion sensors reliable?
We found no independent test, so we cannot rate them. They ignore animals below a stated weight, but pets that climb furniture can still trigger them. Check the maker's pet weight rating and mounting height, run a walk test while your pet moves, and consider contacts only in rooms where pets roam.
What is a glass-break sensor and does it work on laminated or hurricane glass?
A glass-break sensor listens for the sound or feels the shock of breaking glass. We found no named test showing how these work on laminated or impact-rated glass, so do not assume they do. Ask the maker in writing whether your model is rated for your glass, and add contacts on the frame as a backup.
Which entry points do burglars use most?
A 2010 BJS report on 2003 to 2007 data says damaging or removing a door was the most common entry in forcible and attempted forcible entries, and that 40% of unlawful entries into unoccupied homes were through an unlocked door or window. We could not load FBI breakdowns. Protect every ground-level door and window first.
How many sensors does a typical house need?
No standard sets a number. Count every exterior door and ground-floor window that opens, add upper windows reachable from a roof, tree or porch, add the garage entry door, then add motion along the main routes and glass-break in rooms with big panes. A small apartment may need a few; a two-story house many more.
Where should sensors not go?
Do not aim motion sensors at sunny windows, vents, heaters, fireplaces or ceiling fans, and do not hide them behind furniture. Do not use a magnet contact where steel or shutters interfere, or where the gap exceeds the maker's limit. Follow each sensor's manual because mounting rules differ by model.
What causes sensor false alarms?
Common causes are arming away with someone or a pet inside, doors that do not latch, low sensor batteries, shifted mounts, heat or drafts near motion sensors and storm power flickers. Texas bars installing panels that fail ANSI false alarm reduction standards, and cities charge fees after a set number of false alarms.
Sources
- U.S. Bureau of Justice Statistics, Victimization During Household Burglary (NCJ 227379, September 2010)
- Santa Barbara County Sheriff's Office, CPTED Residential Guidelines
- Houston Police Department, Burglary Prevention for Your Home brochure
- Florida Sheriffs Association, How to Prevent a Home Burglary
- FLASH, Protect Your Windows
- National Weather Service, Hurricane Safety Tips and Resources
- CPSC, Smoke Alarms: Why, Where, and Which? (Pub. 559)
- Texas Occupations Code ch. 1702 (Private Security Act)
- Texas Property Code ch. 92 (landlord and tenant)
- Texas Property Code ch. 202 (HOA security measures)
- Florida Statutes 489.529 (alarm confirmation)
- Florida Statutes 489.503 (exemptions)
- Florida Statutes 83.51 (landlord's obligation to maintain premises)
- Florida Statutes 83.52 (tenant's obligations)
- Florida Statutes 627.0629 (residential property insurance rate filings)
- Houston Permitting Center, residential burglar alarm permit and false alarm fees
- City of Austin Police, Alarm Administration
- City of San Antonio, Alarm Response Permits
- City of Orlando, False Alarm Reduction Program
- Jacksonville Sheriff's Office, Alarm Registration
- City of Miami, alarm fees and false alarm rules
- City of Tampa Police, False Alarm Reduction Program
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


