New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Plumbing

No Hot Water? How Do You Troubleshoot Gas, Electric and Tankless Heaters?

A plain-English troubleshooting guide for sudden loss of hot water, lukewarm showers and hot water that runs out, plus what Texas and Florida law says landlords must provide.

Start with the energy supply. For an electric heater, check the breaker, then press the red high-limit reset button behind the upper panel with power off. For a gas heater, check that the gas is on and the pilot or igniter lights. For a tankless unit, read the error code and check gas, power and the inlet filter. If only one faucet is cold, the problem is that faucet's valve, not the heater. Texas landlords must supply a device that makes water of at least 120F.

Key facts

  • Texas Property Code 92.052 requires landlords to repair a landlord-provided device that fails to supply hot water of a minimum temperature of 120F, once a tenant current on rent gives notice.
  • Texas presumes seven days is a reasonable time for a landlord to repair after notice (Prop. Code 92.056).
  • Fla. Stat. 83.51(2)(a)5: unless agreed otherwise in writing, landlords of units other than single-family homes or duplexes must provide functioning facilities for hot water.
  • The U.S. Consumer Product Safety Commission urges lowering water heaters to 120F; it says 140F water can cause third-degree burns in six seconds and 130F in thirty seconds.
  • A. O. Smith manuals: after the high-limit (energy cut-off) trips, the heater cannot restart until the water cools, roughly to 120F or by about 20F, and the reset button is pressed; repeated tripping is a sign of a fault.
  • A. O. Smith manuals: short, repeated heating cycles can push point-of-use temperatures up to 20F above the thermostat setting, and water over 125F can cause severe burns instantly.
  • Electric storage water heaters typically have two thermostats; CPSC's safety alert notes both must be set to a common temperature for proper operation.
  • DOE's 2024 rule (compliance for products made on or after May 6, 2029) will require heat pump technology for most electric storage heaters over 35 gallons.

Why do I suddenly have no hot water?

When hot water stops all at once across the whole house, the heater has lost its energy supply or its safety controls shut it down. When the water is warm but not hot, or runs out fast, the heater is working but cannot keep up. When only one faucet or shower is cold, the heater is fine and the problem is at that fixture.

SymptomMost likely causeFirst check
No hot water anywhere, electric tankTripped breaker, tripped high-limit, burned-out elementBreaker, then the reset button
No hot water anywhere, gas tankPilot out, gas off, failed thermocouple or flame sensor, failed igniterGas valve on, look through the sight glass for a flame
No hot water, tanklessError code, gas or power off, clogged inlet filter, scale, freeze damageDisplay code and the manual's code table
Lukewarm waterOne failed element, broken dip tube, thermostat set low, sedimentThermostat setting, then elements
Hot water runs out fastTank too small, lower element out, sediment, broken dip tubeLower element and dip tube
Hot in the kitchen, cold in one bathroomShower cartridge or anti-scald valveThe shower valve
Rusty or smelly hot waterAnode rod or tank corrosionAnode, tank age

Why is my electric water heater not heating, and how do I reset it?

An electric tank has two heating elements (upper and lower), each with its own thermostat, plus a high-limit safety switch, sometimes called the ECO, with a red reset button. Work through these in order:

  1. Check the breaker. Electric tank heaters run on a double-pole (two-handle) breaker. If it tripped, reset it once. If it trips again, stop and call a plumber or electrician. A shorted element or wiring problem is likely.
  2. Turn power off at the breaker before opening any panel. Electric water heater wiring is 240 volts.
  3. Press the reset button. Remove the upper access panel and insulation. Press the red button firmly. Manufacturer manuals explain the high-limit control will not let the heater restart until water cools, then the button must be pressed. Replace insulation and cover, turn power on, and wait.
  4. Give it time. A typical 40 to 50 gallon electric tank needs an hour or more to reheat from cold.
  5. If it trips again, that is a warning. Manuals say continued manual resetting, preceded by hotter than usual water, is evidence the high-limit is doing its job because something is overheating, often a stuck thermostat or an element shorted to the tank.

Testing elements

With power off, a plumber or handy owner can check each element with a multimeter for resistance and for a short to the tank. A failed upper element usually means no hot water at all, because the upper element heats first and then hands off to the lower one. A failed lower element usually means a small amount of hot water that runs out quickly. Elements are cheap parts, but replacing one means draining the tank and working near 240 volts. If you are not comfortable, hire it out.

Thermostats

The CPSC's safety alert notes that most electric water heaters have two thermostats, and both must be set to a common temperature for proper operation. If the lower thermostat is set far below the upper one, hot water runs out fast.

How do I relight a gas water heater pilot, and why does it keep going out?

Older gas tanks have a standing pilot light. Newer ones often use an electronic igniter or a piezo push-button. Follow the lighting instructions on the label on the front of your heater. They differ by model, and the label is the authority. The general pattern:

  1. Smell first. If you smell gas, do not light anything. Manufacturer manuals say: do not try to light any appliance, do not touch any electrical switch, do not use a phone in the building, and call your gas supplier from a neighbor's phone. If you cannot reach them, call the fire department. See gas leak: what to do.
  2. Turn the control knob to Off and wait the time on the label for gas to clear.
  3. Turn to Pilot, push and hold the knob, and press the igniter (or light per the label).
  4. Keep holding for the time stated so the thermocouple or thermopile heats up.
  5. Release and turn to On. The main burner should light.

Why the pilot keeps going out

  • Weak or failed thermocouple or thermopile. This sensor tells the gas valve the pilot is lit. When it fails, the valve shuts the gas off. It is the most common cause and an inexpensive part.
  • Dirty pilot orifice. A weak, yellow or flickering pilot flame does not heat the sensor well.
  • Drafts or venting problems. Wind down a flue or a blocked vent can blow out the pilot. A tripped flammable-vapor or high-temperature sensor on newer heaters also shuts them down.
  • Low gas supply. If other gas appliances are weak too, call the gas utility.
  • Failed gas control valve. If a new thermocouple does not fix it, the control may need replacement. That is a licensed plumber's job.

Electronic-ignition commercial models in A. O. Smith manuals lock out if the pilot does not light within 15 seconds and must be reset by switching the burner off for at least a minute. Home models vary; check your manual.

Why is my tankless water heater not producing hot water?

Tankless (on-demand) heaters fire only when water flows above a minimum rate. Common causes of cold water:

  • Error code on the display. Look it up in the manual or on the maker's site before anything else. Codes point to ignition failure, flame loss, overheating, venting, or freeze protection.
  • Flow too low. If you open a faucet just a little, the unit may not sense enough flow to fire. Clogged aerators or showerheads lower flow too.
  • Clogged inlet filter. Most units have a small screen at the cold water inlet. Sand and debris after a main break or repair can clog it.
  • Scale. Hard water coats the heat exchanger. Manufacturers usually call for periodic descaling (flushing with a descaling solution through service valves). Units in hard-water areas may need it every year.
  • Gas supply too small. Tankless gas units need much more gas at once than a tank. If a unit was added without upsizing the gas line or meter, it may fail under heavy use.
  • Power loss. Gas tankless units still need electricity for controls and fans.
  • Freeze damage. Many units protect themselves with small electric heaters that only work with power on. During Winter Storm Uri in February 2021, Texas saw long power outages: ERCOT reports generation outages peaked near 52,000 MW on February 16. If your outdoor unit lost power in a hard freeze, have it checked for cracked components before relying on it. See frozen pipes in Texas.

Cold water sandwich

A short burst of cold water between hot uses is normal with many tankless units. The water sitting in the pipe cools, and the heater needs a few seconds to fire again. A recirculation pump or a unit with a small buffer tank reduces it.

Why does my hot water run out so fast, or come out lukewarm?

  • Broken dip tube. The dip tube carries incoming cold water to the bottom of the tank. If it cracks, cold water mixes in at the top, right where hot water leaves. You get lukewarm water quickly, and you may find bits of white plastic in faucet aerators. Water heater manuals show the dip tube on the cold inlet. Replacing it is a moderate job.
  • Sediment. Mineral buildup takes up space and insulates the water from a gas burner or buries the lower electric element. Annual flushing helps.
  • Failed lower element (electric). The upper element can only heat the top part of the tank.
  • Thermostat set low. A 120F setting is the CPSC recommendation for safety. If someone turned it lower to save energy, showers feel lukewarm.
  • Tank too small for the household. Back-to-back showers, a big tub and a washer at once can empty a 40-gallon tank. Fixr's 2026 guide lists 40 gallons for 1 to 4 people and 50 gallons for 3 to 5 people as rough sizing ranges.
  • Crossed connection. A faulty mixing valve or single-handle faucet can let cold water cross into the hot line, making all hot taps lukewarm. Shutting the cold supply to the heater and opening a hot tap is a common test: if water keeps flowing, something is crossing over.

How long does a water heater take to recover?

Recovery depends on burner or element size, tank size, and how cold the incoming water is. Gas tanks heat faster than standard electric tanks because burners deliver more heat than elements. Your heater's label or manual lists its recovery rate in gallons per hour at a stated temperature rise. Incoming water is warmer in Texas and Florida summers, so recovery is faster then.

Hot water in the kitchen but not the bathroom: is it the heater?

No. If any faucet in the house gets hot, the heater works. The problem is the fixture.

  • Shower cartridge. Single-handle showers use a cartridge that mixes hot and cold. Cartridges wear, clog with scale, or get installed with hot and cold reversed. A new cartridge is a common fix.
  • Anti-scald (pressure-balancing or thermostatic) valve. These limit how hot the shower can get. A rotational limit stop set too low makes the shower lukewarm even when the faucet is fully hot. Adjusting the stop is often a five-minute job once the handle is off.
  • Long pipe runs. A far bathroom may take minutes to get hot. That is distance, not failure.
  • Stuck mixing valve. Some homes have a mixing valve at the heater that tempers hot water to a safe level. If it fails, it can deliver too cool or too hot water everywhere.

Water heater manuals recommend temperature-limiting devices such as mixing valves at fixtures because water hot enough for dish and clothes washing can scald, and they note water over 125F can cause severe burns instantly. Children, the elderly and people with disabilities are at highest risk.

What temperature should a water heater be set to?

Start at 120F. The CPSC urges all users to lower water heaters to 120F to prevent tap water scalds, and its safety alert lists how fast burns happen:

Water temperatureTime to third-degree burn in most adults (CPSC)
150F2 seconds
140F6 seconds
130F30 seconds
120FFive-minute exposure could still cause burns

To check, CPSC suggests holding a candy or meat thermometer under the faucet first thing in the morning or at least two hours after water use, then adjusting the thermostat per the manufacturer's instructions and checking again. Texas uses the same 120F number as the minimum a landlord-provided heater must deliver. Some households with specific health needs set it higher with mixing valves at fixtures; talk with a plumber about that setup.

Note that the DOE's 2029 rule will limit some small electric units (20 to 35 gallons) to a 135F maximum setting, according to A. O. Smith's summary of the rule.

How long can a landlord leave me without hot water in Texas or Florida?

Texas

Texas Property Code 92.052 makes hot water an explicit repair duty. The landlord must make a diligent effort to repair a condition that arises from failing to provide and maintain a device to supply hot water of a minimum temperature of 120F, if the tenant gives notice to the place rent is paid and is not behind on rent. Notice must be in writing only if your written lease requires it, but writing is always smarter.

  • Reasonable time: The law presumes seven days is reasonable (92.056), but the presumption can be rebutted by the nature of the problem and availability of parts and labor.
  • Remedies: If the landlord fails after proper notice and time, 92.056 and 92.0561 allow, under conditions, ending the lease, repair-and-deduct (capped at the greater of one month's rent or $500) using a licensed contractor where required, or going to justice court. Courts can order repairs, reduce rent, and award a civil penalty of one month's rent plus $500, actual damages and attorney's fees (92.0563). Justice courts may not award more than $20,000.
  • Be careful: Texas remedies have strict steps, including notice requirements. Follow them exactly or you can lose the protection. The Texas Attorney General's consumer pages and local legal aid groups can help.

Florida

Florida Statute 83.51(2)(a)5 requires landlords of units other than single-family homes or duplexes to make reasonable provision for functioning facilities for heat during winter, running water, and hot water, unless otherwise agreed in writing. For single-family homes and duplexes, the lease can shift these duties in writing. If the landlord does not fix a material problem, the tenant may withhold rent as a defense only after 7 days have passed since delivering written notice specifying the problem and the intent to withhold (83.60). Florida preempted local landlord-tenant ordinances in 2023 (83.425), so state law is the main rule. More detail in Texas and Florida landlord repair guides.

Is no hot water an emergency repair?

Leases and property managers usually treat it as urgent but not a same-night emergency, unless it comes with a leak, gas smell or electrical problem. Report it right away in the way the lease requires, keep a copy, and note the date and time.

When should I call a plumber instead of fixing it myself?

  • Any gas smell, sooting, scorch marks, or a pilot that will not stay lit after a thermocouple swap.
  • A breaker or reset button that trips again.
  • Water on the floor or a leaking tank (see water heater leaking).
  • Tankless error codes for ignition, flame or venting.
  • Replacing the heater. In Houston, a permit pulled by a city-registered master plumber is required for replacement. Texas homestead owners may do their own plumbing but still need permits where the city requires them.

In Texas, check the plumber on the TSBPE license search. In Florida, check the DBPR licensee search for a CF or RF plumbing license. If your heater is near the end of its life, our replacement cost guide and tank vs tankless vs heat pump comparison help you choose.

How to choose a provider

  • Check whether every faucet is cold or just one.
  • Electric: check the double breaker, then the red reset with power off.
  • Gas: confirm the gas valve is on and look for a flame; relight per the label.
  • Tankless: note the error code and check the inlet filter.
  • Check the thermostat; 120F is the CPSC recommendation.
  • Look in faucet aerators for white plastic bits (broken dip tube).
  • Flush sediment if water runs out fast or the tank rumbles.
  • Renters: give written notice and keep a dated copy.
  • Stop and call a licensed plumber if you smell gas or a reset trips twice.

Related plumbing guides

Plumbing by state and city

Questions people ask

Why do I have hot water in the morning but not at night?

The tank is emptying faster than it recovers. That points to a failed lower element on an electric tank, heavy sediment, a broken dip tube, a thermostat set low, or a tank that is too small for evening demand. Stagger showers and laundry for a few days while you check the elements and dip tube. If the tank is 10 or more years old, plan for replacement.

Can a power outage cause no hot water after it comes back?

Yes. A power surge can trip the high-limit switch on electric tanks, and tankless units may show a code after restart. Gas tanks with electronic ignition need power too. Reset per the manual. If you lost power in a freeze, check outdoor tankless units and exposed pipes for cracks before turning water back on.

Why is my hot water too hot all of a sudden?

A stuck thermostat or failed gas control can overheat the tank, which is dangerous. Turn the heater off and call a plumber. Signs include water hotter than normal, steam, and the T&P relief valve discharging. Manufacturer manuals say repeated high-limit tripping that follows unusually hot water is evidence of a control fault.

My landlord says the water heater is fine but the water is barely warm. What can I do?

Measure it. Run hot water for a minute and hold a kitchen thermometer under the stream, then photograph the reading. Texas Property Code 92.052 sets a 120F minimum for a landlord-supplied heater, so a reading well below that supports a repair request. Send written notice to the place rent is paid and keep a copy. In Florida, multi-unit landlords must provide hot water facilities unless the lease says otherwise in writing.

Is it worth fixing a 12-year-old water heater with no hot water?

A cheap fix like a reset, breaker, thermocouple or element can buy time. But most tank heaters last roughly 8 to 15 years (Fixr's guides cite 8 to 12 years in some places and 10 to 15 in others), and an older tank that also leaks, rumbles loudly or gives rusty water is near the end. Florida owners should also consider what their insurer accepts on a 4-point inspection. Compare a repair quote against a replacement quote.

Why does my shower go cold when someone flushes a toilet?

In older homes, a flush pulls cold water away from the shower, so the shower suddenly gets hotter, or, with some valves, cooler. Modern pressure-balancing shower valves are designed to hold the mix steady when pressure changes. If your shower swings wildly, the valve may be an older type or its cartridge may be worn. A plumber can replace the cartridge or valve.

Do I need to drain a water heater to replace an element?

For a screw-in element below the water line, yes. Shut off power, close the cold inlet, open a hot faucet, and drain at least below the element. Refill the tank completely, with water flowing from a hot faucet, before turning power back on, or the new element will burn out instantly. If any step is unclear, hire a plumber.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration