Local Guide · Plumbing
Why Is My Water Heater Leaking, and Should I Repair or Replace It?
Find where the water is coming from, shut the heater down safely, and decide between a cheap fix and a new tank. Includes Texas and Florida permit, insurance and attic-install rules.
Find the leak's source first. Water from the top fittings, the drain valve or the relief valve (T&P) can often be fixed for little money. Water from the tank body itself, usually a rusty puddle under the heater, means the tank has corroded through and must be replaced. Turn off power or gas, close the cold inlet valve, and drain the tank if the leak is heavy. Replacement usually needs a permit in Texas and Florida cities.
Key facts
- Water heater manuals from A. O. Smith state plainly: 'All water heaters eventually leak,' and say not to install a heater without adequate drainage.
- Manufacturer manuals call for a metal drain pan at least 2 inches deep and at least 2 inches wider than the heater, piped to an adequate drain, where a leak could damage the building.
- A. O. Smith: the T&P relief valve is not intended for constant relief of thermal expansion; properly sized thermal expansion tanks are required on closed water systems.
- T&P discharge piping must end within 6 inches above an adequate floor drain or outside the building, per A. O. Smith manuals.
- Houston requires a plumbing permit for water heater replacement, obtained by a master plumber registered with the city; the fee is $34.24 for the first three heaters plus a $33.56 admin fee, and the city page lists the minimum as both $91.05 and $97.56 (fee schedules change).
- Most tank water heaters last roughly 8 to 15 years (Fixr's January 2026 guides cite 8 to 12 and 10 to 15).
- Water heater replacement costs: Bob Vila/Angi average $1,293 (range $874 to $1,765, 2024); Fixr average about $1,400 (2026); This Old House average $1,950 (2026). Gulf Coast installs run 10% to 20% above national average (This Old House).
- Citizens' Florida 4-point inspection form asks the water heater's age and location, whether it has a T&P valve, and requires a photo of the heater including the valve.
- TDI: home policies typically cover sudden and accidental water discharge but not gradual leaks or seepage.
Is a leaking water heater an emergency?
It depends on how much water and where it is going. A slow drip from a fitting is urgent but not an emergency. A steady stream, water spreading across the floor, a leak in an attic, or water near electrical wiring is an emergency. So is any leak with a gas smell, scorch marks, or a relief valve that keeps blowing hot water.
Most tank heaters hold 40 to 50 gallons, and the cold water line keeps refilling the tank as water escapes. That means a failed tank can keep leaking until you close the cold inlet valve. In Texas, many tract homes put the water heater in the attic. A failed attic tank drains straight through the ceiling into living space, so treat any attic leak as an emergency.
Can a leaking water heater explode?
A leak by itself does not cause an explosion. The danger is a tank that overheats with a failed or blocked relief valve, which is why the T&P valve and its drain pipe must never be capped or plugged. Gas heaters add the risk of a gas leak or poor venting. Water heater manuals also warn that hydrogen gas can build up in a system that has not been used for a long time, and they tell owners not to use a heater that has been flooded or water-damaged until a qualified technician inspects it.
How do I shut off and drain a leaking water heater?
- Cut the energy. Electric: switch off the double breaker at the panel. Gas: turn the control knob to Off (or Pilot), then close the gas valve on the supply line.
- Close the cold water inlet. It is the valve on the pipe entering the top of the tank, usually marked or colder to the touch. If it will not close or is the part leaking, close the home's main shut-off.
- Open a hot faucet somewhere in the house to let air in and relieve pressure.
- Attach a garden hose to the drain valve at the bottom of the tank and run it to a floor drain, outside, or a bucket you can empty. Water inside can be scalding. Let it cool for a few hours if you can wait.
- Open the drain valve and let the tank empty. If sediment clogs it, close it, let pressure build briefly, and try again, or call a plumber.
- Mop and dry. Pull wet items away and run fans. The EPA says to dry water-damaged areas within 24 to 48 hours to prevent mold.
Do not turn power or gas back on until the tank is full again, with water coming out of a hot faucet. Firing an empty tank can burn out electric elements in seconds.
Where is the leak coming from? A decision tree
Dry the outside of the tank and floor with towels, then watch for where water reappears. Use a flashlight and look up, not only at the puddle.
| Where you see water | Likely cause | Usual fix | Replace the heater? |
|---|---|---|---|
| Top: on the cold or hot pipe connections | Loose fitting, failed flex connector or corroded dielectric nipple | Tighten or replace connectors | No, if the tank is sound |
| Top: from the anode rod port | Worn anode or leaking seal | Replace anode and reseal | Usually no |
| Side: from the T&P valve or its discharge pipe | Excess pressure, overheating, thermal expansion, or a worn valve | Find the cause; replace the valve; add an expansion tank if the system is closed | No |
| Bottom: from the drain valve | Valve not fully closed, worn washer, or sediment in the seat | Close it, cap it, or replace the valve | No |
| Bottom: from under the jacket or burner area, rusty water | The steel tank has corroded through | None that lasts | Yes |
| Water on the burner or in the combustion chamber (gas) | Tank leak, or condensation on a cold startup | Watch for a day; condensation stops as the tank warms | Yes, if it continues |
| Floor nearby but heater is dry | A different source: HVAC condensate line, supply line, slab or drain leak | Trace it | No |
Tank-body leak means replacement
Once the glass-lined steel tank itself leaks, there is no reliable repair. Patching the outer jacket does nothing because the hole is in the inner tank. Plan for a replacement, and in the meantime, keep the inlet closed and the power or gas off.
Water heater leaking from the top: fixable?
Usually. Top leaks most often come from the water connections, the anode port, or the T&P valve threads. These are parts, not the tank, and a plumber can swap them in under an hour. Corrosion where copper meets the steel tank fittings is a frequent culprit, and mineral crust around a fitting is a clue.
Why is water coming out of the pressure relief (T&P) valve?
The temperature and pressure relief valve (T&P or TPR valve) is the brass valve on the side or top of the tank, with a pipe running down toward the floor or outside. It opens if tank pressure or temperature gets too high. That makes it a safety device, not a leak. Common reasons it discharges:
- Thermal expansion. Water expands when heated. If your home has a check valve, backflow preventer or pressure-reducing valve (PRV) at the meter, the expanded water cannot push back into the city main. That is called a closed system. Pressure spikes every time the heater runs, and the T&P drips. A. O. Smith's manuals say the T&P valve is not intended for constant relief of thermal expansion and that properly sized thermal expansion tanks are required on all closed water systems. Thermal expansion can also cause premature tank failure that the warranty does not cover.
- High street pressure. If incoming pressure is high, a PRV may be needed. A pressure gauge on a hose bib tells you. See water pressure.
- Overheating. A stuck thermostat or failed gas control can overheat the water. Hot water spraying from the valve is a sign to shut the heater off and call a plumber.
- A worn valve. After years of service, or after being tested, a valve may not reseat. Manuals say that if the valve fails to completely reset and keeps releasing water, close the cold inlet, drain the tank, and replace the valve with a properly rated new one.
Never plug, cap or remove the T&P valve or its discharge pipe. A. O. Smith requires the discharge pipe to end within 6 inches above an adequate floor drain or outside the building, and the valve's set pressure may not exceed the heater's marked working pressure (150 psi).
Do water heaters need a drain pan and an expansion tank by code?
Requirements come from the plumbing code your city adopted, plus the manufacturer's instructions, which inspectors also enforce.
- Drain pan: Manufacturer manuals call for a suitable metal drain pan where a leak could damage the building or a floor below, with sides at least 2 inches deep and length and width at least 2 inches greater than the heater's diameter, piped to an adequate drain. Attics, upper floors and finished interior closets are the typical cases. Your local code and inspector decide exactly where a pan is required, so ask the building department.
- Expansion tank: Required where the system is closed (a check valve, backflow device or PRV stops water from flowing back to the main), per manufacturer instructions and the codes. Many Texas and Florida utilities install backflow devices or check valves at meters, so ask the plumber to check.
- Which code applies: Florida uses the Florida Building Code, Plumbing, 8th Edition (2023), based on the 2021 International Plumbing Code. In Texas, cities choose. Houston amended the 2021 Uniform Plumbing Code effective January 1, 2024. Austin lists the 2024 UPC. Dallas uses the 2021 IPC with local amendments. San Antonio adopted the 2024 ICC codes in January 2025.
Attic water heaters in Texas
Attic installs save floor space but raise the stakes on any leak. Look for a pan with a drain line that runs outside or to a drain, not a pan with no outlet. Houston's code amendments include ladder and access requirements for attic water heaters. If your pan drains to a spot you never see, put a water sensor in the pan.
Garage and outdoor heaters in Florida and Texas
Gas heaters in garages must keep burners and ignition sources raised off the floor. Houston's amendments set that at not less than 18 inches, to keep flames above gasoline vapors. Outdoor and garage heaters in hurricane areas may need anchoring; ask your local building department what it requires, because we could not confirm a single statewide Florida strapping rule for this guide.
Repair or replace a leaking water heater?
| Situation | Lean toward |
|---|---|
| Tank body leaking, rust under the heater | Replace |
| Heater 10+ years old with any significant leak | Replace (most tanks last roughly 8 to 15 years) |
| Under 8 years, leak at a valve or fitting | Repair |
| T&P drips on a closed system | Add expansion tank or PRV; repair |
| Rumbling, popping, rusty hot water and age near the limit | Plan replacement before it fails |
| Florida home with a heater your insurer flagged on a 4-point | Replace may be needed to keep coverage |
| Still under warranty | Call the manufacturer first; many tank warranties run 6 to 10 years |
Fixr notes standard tank warranties run 6 to 10 years. Warranties often exclude damage from thermal expansion or a missing expansion tank, so keep your install paperwork.
How long do water heaters last in Texas and Florida?
Most tank water heaters last roughly 8 to 15 years: Fixr's 2026 cost guides cite 8 to 12 years on its main installation page and 10 to 15 on its 50-gallon page, and a plumber quoted by Bob Vila gives a similar range. Hard water shortens that. Minerals settle as sediment in the bottom of the tank, which makes gas heaters rumble and pop and makes electric lower elements fail. The USGS says hardness varies across the country and classifies 121 to 180 mg/L (as calcium carbonate) as hard and more than 180 mg/L as very hard. Your utility's annual water quality report lists your number.
Things that add years: flushing sediment once a year, checking the anode rod every few years (manuals say to inspect anode rods regularly and replace if damaged), keeping pressure under control with a PRV and expansion tank, and setting the temperature no higher than you need. See water heater maintenance and hard water.
How do I find my water heater's age?
Look at the rating label on the side of the tank. Many brands code the manufacture date into the serial number, usually as a letter or digits for the month and two digits for the year. Formats differ by brand and have changed over time, so check the maker's website or call their support line with the model and serial number. We are not publishing a brand-by-brand decoder here because we could not verify each format against manufacturer sources. Some installers also write the install date on the tank with a marker.
Why does my water heater pop or rumble?
Usually sediment. Water trapped under a layer of mineral scale boils in small bursts. It is not dangerous by itself, but it wastes energy and stresses the tank bottom. Flushing helps if done before the layer hardens. If a tank that has rumbled for years starts leaking, it is usually at the end of its life.
What does a water heater replacement cost installed?
Different national cost guides use different data, so the numbers do not match. Here is what each says, with its date.
| Source | Average | Range |
|---|---|---|
| Bob Vila (Angi/HomeAdvisor data, April 2024) | $1,293 | $874 to $1,765 |
| Fixr (January 2026) | About $1,400 | $900 to $3,000 (gas tank) |
| Fixr, 50-gallon units (January 2026) | About $1,800 | $900 to $2,500 |
| This Old House (Home Depot data, June 2026) | $1,950 | $1,600 to $5,400; tankless about $2,800 |
This Old House reports Gulf Coast installs run 10% to 20% above the national average. Extras that push the price up:
- Permits: Bob Vila puts water heater permits at $25 to $300 (2024). Houston's water heater page lists the minimum permit fee as both $91.05 and $97.56, plus a $33.56 admin fee.
- Expansion tank, new pan and drain line, new shut-off valve.
- Code upgrades on gas venting, gas line sizing or electrical.
- Attic access and haul-away.
- After-hours work: This Old House lists $200 to $500 extra for after-hours or weekend installs.
- Switching type: going tankless or heat pump can add gas line, venting or electrical work.
Federal efficiency rules are changing too. The U.S. Department of Energy's 2024 rule, with compliance required for products made on and after May 6, 2029, will effectively require heat pump technology for most electric storage heaters over 35 gallons. See replacement cost and tank vs tankless vs heat pump.
Do I need a permit, and can I replace my water heater myself?
Texas
Texas cities over 5,000 people must require permits for plumbing work, with narrow exceptions for leak repairs and swapping faucets, ballcocks, disposals and toilets (Occupations Code 1301.551). A water heater replacement is not on that exception list. Houston requires a permit for water heater replacement and installation, pulled by a master plumber registered with the city. Texas law lets a property owner do plumbing on their own homestead without a license (1301.051). Houston's amendments confirm a homeowner may install plumbing in an owner-occupied homestead and apply for a permit, but are not exempt from permits or fees. Rentals and properties that are not your homestead need a licensed plumber.
Florida
Florida local building departments enforce the Florida Building Code. Jacksonville requires a permit for water heater replacement. Tampa issues a plumbing trade permit without plan review for a same-location water heater replacement with no fuel conversion. Unincorporated Miami-Dade's exemption list (2018 revision) lets licensed plumbing contractors replace an electric water heater up to 50 gallons without a plumbing permit, and an electric heater of 4,500 watts or less without an electrical permit, unless the new one draws more watts. Confirm the current list before you rely on it. Homeowners may pull an owner-builder permit for their own one- or two-family home under Florida Statute 489.103(7), which requires signing a disclosure and personally supervising the work.
Doing it yourself is legal for owner-occupants in both states with the right permit, but gas connections, venting and T&P piping are where DIY installs fail inspection. See permits and DIY rules.
Is water heater leak damage covered by insurance?
The damage from a sudden tank failure usually is. The water heater itself usually is not, because wear and tear and the failed appliance are excluded. A slow leak that rotted the floor for months often is not covered either.
- Texas: TDI says most policies cover sudden and accidental water discharge, including from a broken appliance, but not gradual leaks or seepage. Some Texas forms exclude seepage from an appliance over 14 or more days. TDI also says the first two appliance-related water damage claims do not count toward nonrenewal if repaired and passed inspection.
- Florida: In 2018 Citizens' board approved a policy-form cap (not a statute) on non-weather water losses, explicitly including a leaking water heater, at $10,000 (with $3,000 for mitigation) for policyholders who decline managed repair. Many private carriers have similar sub-limits. Check your declarations page.
- Florida 4-point inspections: Insurers use them on older homes. Citizens' form records the heater's age, location and T&P valve and requires photos. Insurers set their own age cutoffs, which vary by carrier, so ask your agent what age your carrier accepts before your inspection. See Florida 4-point plumbing.
Report the loss quickly and photograph the tank label, the leak and the damage before the old heater is hauled off. Ask the plumber to note the cause on the invoice.
What about renters whose water heater is leaking?
Tell the landlord in writing right away and turn off the heater's power or gas and the inlet valve if water is spreading. In Texas, Property Code 92.052 requires landlords to repair a landlord-supplied hot water device that cannot produce water of at least 120F after proper notice, and flooding from a broken pipe in the unit triggers immediate repair-and-deduct after notice of intent (92.0561). In Florida, landlords of units other than single-family homes and duplexes must provide hot water unless agreed otherwise in writing (83.51). More in no hot water.
How to choose a provider
- Find your heater's cold inlet valve and the breaker or gas valve now.
- Read the rating label and note the model, serial number and age.
- Check that the T&P discharge pipe runs to a drain or outside and is not capped.
- Look for a drain pan with a working drain line, especially in attics.
- Ask whether your home has a check valve, backflow device or PRV; if so, confirm an expansion tank.
- Flush sediment once a year and check the anode rod every few years.
- Put a water leak sensor in the pan or next to the heater.
- Florida owners: ask your insurer what water heater age it accepts before a 4-point.
- Get a written quote that includes permit, expansion tank, pan and haul-away.
- Confirm the plumber's license (TSBPE in Texas, DBPR in Florida) before work.
Related plumbing guides
- No Hot Water? How Do You Troubleshoot Gas, Electric and Tankless Heaters?
- How Much Does It Cost to Replace a Water Heater, and Why Is My Quote Higher Than the Store Price?
- How Do I Maintain a Water Heater? Flushing, Anode Rods, Relief Valve Tests and Tankless Descaling
- Tank vs Tankless vs Heat Pump Water Heater: Which Is Best in Texas and Florida?
- What Does a Florida 4-Point Inspection Check on Plumbing, and How Do You Pass?
- Do I Need a Permit? Plumbing Permits and DIY Rules in Texas and Florida
- Why Is My Water Pressure Low (or Too High)? Causes, PRVs, Testing and Fixes in Texas and Florida
- Do Home Warranties Cover Plumbing in Texas and Florida, and What Do They Leave Out?
Plumbing by state and city
Questions people ask
Why is my water heater leaking from the bottom?
The three common causes are the drain valve (not fully closed, a worn washer or sediment), water running down from a leak at the top or the T&P pipe, and a corroded tank. Dry everything and watch. If the drain valve drips, a cap or new valve fixes it. If rusty water comes from under the tank jacket with no other source, the tank has failed and needs replacement.
Can I keep using a water heater that leaks a little?
Only if the leak is at a fitting or valve and you are fixing it soon, with a pan or bucket catching the water. A leak from the tank body only gets worse, and when it fails fully the cold line keeps refilling it. In an attic or upstairs closet, do not wait. Turn it off, close the inlet and replace it.
Why does my water heater leak only when it heats?
That points to thermal expansion. As water heats, it expands. In a closed system, with a check valve, backflow device or pressure-reducing valve at the meter, pressure climbs and the relief valve weeps. Manufacturers say expansion tanks are required on closed systems and that the T&P valve is not meant for constant relief of expansion. A plumber can test pressure and add a properly sized expansion tank.
What temperature should the water heater be set to?
The U.S. Consumer Product Safety Commission urges users to lower water heaters to 120F to prevent tap water scalds. Its safety alert says most adults suffer third-degree burns from 150F water in two seconds and from 140F water in six seconds. Texas landlord law uses 120F as the minimum a landlord-supplied heater must reach. Higher settings also speed up sediment and scale.
How long does a water heater replacement take?
A same-type, same-location swap usually takes a few hours once the plumber is on site, plus time to drain and haul the old tank. Moving the heater, converting fuel types, or going tankless takes longer and may need extra permits for gas or electrical work. Inspections are usually scheduled after the install. Houston lists a one-business-day processing time for water heater permits.
Will a home warranty pay for a leaking water heater?
Many home warranty contracts cover water heater repair or replacement but set dollar caps, exclude code upgrades like expansion tanks, pans and venting, and exclude water damage. They are service contracts, not insurance. Read the water heater and exclusions sections before you call. Our home warranty guide explains how claims work and how to dispute a denial.
Is it normal for a new water heater to drip?
A little condensation on a gas heater's burner during the first cold fill can be normal and stops as the tank warms. Drips at new connections usually mean a fitting needs tightening. A relief valve that drips on a new heater often means the system is closed and needs an expansion tank or a PRV. Call the installer back, since that is often covered under their workmanship warranty.
Should I replace a 12-year-old water heater that is not leaking?
Many owners do, to avoid an emergency replacement and water damage. Most tanks last roughly 8 to 15 years. In Florida, an older heater can also cause trouble on a 4-point inspection, depending on the carrier. Replacing on your schedule lets you compare quotes, plan for the 2029 federal efficiency changes, and avoid after-hours rates.
Sources
- A. O. Smith instruction manual (Model 154 series)
- A. O. Smith instruction manual (BTP series)
- American Water Heater instruction manual
- Houston Permitting Center: Water Heater permit
- Houston Amendments to the 2021 UPC
- Texas Occupations Code ch. 1301
- Miami-Dade: Permit exemptions
- Tampa: Trade permit limitations by discipline (2025)
- Jacksonville Building Inspection Division FAQs
- Fla. Stat. 489.103 (owner-builder exemption)
- ICC: Florida Building Code, Plumbing, 8th Edition (2023)
- Austin: Building Technical Codes
- Dallas: Plumbing and Mechanical
- San Antonio DSD: Codes and Ordinances
- Fixr: Water heater installation cost (Jan. 2026)
- Fixr: 50-gallon water heater cost (Jan. 2026)
- Bob Vila: Water heater replacement cost (Apr. 2024)
- This Old House: Water heater installation cost (June 2026)
- DOE: Consumer water heaters standards
- Federal Register: 2024 consumer water heater standards
- CPSC: Avoiding Tap Water Scalds
- TDI: When are water damage and mold covered by insurance?
- TDI: Homeowners insurance guide (cb025)
- TDI: Texas homeowners policy comparison (2018)
- Insurance Journal: Citizens limits non-weather water losses (2018)
- Citizens 4-Point Inspection Form
- Texas Property Code ch. 92
- Fla. Stat. 83.51
- USGS: Hardness of Water
- EPA: A Brief Guide to Mold, Moisture and Your Home
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


