Local Guide · Swimming pool builders and contractors
Pool Heat Pump vs Gas Heater vs Solar: Which Heats a Texas or Florida Pool Best, and What Does It Cost?
Heat pumps, gas heaters and solar panels all warm a pool, but they cost very different amounts to buy and run in Houston, Dallas, Miami or Orlando. Here are DOE's cost tables updated to 2026 energy prices, sizing math, federal efficiency rules, freeze lessons from 2021, and who can install each type.
For most Florida pools and for swimming-season heating in much of Texas, an electric heat pump is the cheapest heater to run, because it moves heat from the air with a coefficient of performance (COP) of about 3 to 7. Gas heaters cost less up front and heat fast in any weather, which suits spas and occasional use. Solar panels have the lowest operating cost but depend on sun and roof space. A pool cover matters more than heater type: DOE says covers can cut heating costs 50% to 70%.
Key facts
- DOE: heat pump pool heaters work efficiently while outdoor air stays above roughly 45 F to 50 F, and COPs usually range from 3.0 to 7.0.
- DOE: covering a pool when it is not in use is the single most effective way to cut pool heating costs, with savings of 50% to 70% possible.
- Federal rule 10 CFR 430.32(k): gas-fired pool heaters made from April 16, 2013 must have at least 82% thermal efficiency; from May 30, 2028, gas and electric pool heaters (including heat pumps) must meet integrated thermal efficiency (TEI) minimums.
- DOE's 2023 pool heater rule analysis estimated an average consumer pool heater lifetime of 11.1 years.
- DOE heater sizing rule of thumb: pool surface area (sq ft) x desired temperature rise (F) x 12 = required Btu per hour.
- DOE: each degree of added pool temperature costs 10% to 30% more in heating energy, depending on location.
- Fixr (updated January 31, 2025): installed pool heaters average $3,500 nationally, with a typical range of $2,500 to $5,000; heat pumps run $2,500 to $6,500 installed.
- DOE: a solar pool heating system usually costs $2,500 to $4,000 to buy and install, pays back in 1 to 7 years, and can last 10 to 20 years with maintenance.
- Florida rule 64E-9.008 caps heated public pool water at 104 F and requires a working in-line thermometer.
- Florida Statute 163.04 bars deed restrictions, covenants and local ordinances from prohibiting solar collectors; Texas Property Code 202.010 limits HOA bans on solar energy devices.
Which pool heater is best for Texas and Florida?
There is no single best heater. The right choice depends on how you swim, where you live and what fuel you have. This table sums up the trade-offs using DOE guidance and Fixr's 2025 cost data:
| Heat pump | Gas (natural gas or propane) | Solar | Electric resistance | |
|---|---|---|---|---|
| How it heats | Moves heat from outdoor air into water | Burns fuel in a combustion chamber | Pumps water through sun-warmed collectors | Electric element heats water directly |
| Installed cost (Fixr, 2025) | $2,500 to $6,500 | $1,500 to $5,500 | $2,500 to $7,000 | $1,000 to $6,000 |
| Running cost | Low (COP 3 to 7) | High per hour of heating | Very low (pump power only) | Highest per unit of heat |
| Heat-up speed | Slow and steady | Fastest | Slow, weather-dependent | Slow |
| Works in cold weather | Loses efficiency below about 45 F to 50 F | Yes, any weather | Weak in cold, cloudy weather | Yes |
| Typical life (DOE) | 10 or more years | 5 or more years | 10 to 20 years | Fixr: 5 to 10 years |
| Best fit | Regular swimmers; most of Florida; Texas spring to fall | Spas, quick weekend heating, cold snaps | Sunny homes with roof space; extending the season | Small spas only |
A practical pattern in both states: heat pump for the pool, gas for an attached spa or a fast boost, solar to stretch the season, and a cover for everything. Many South Florida owners also use heat pumps that can cool the pool in August.
How does a pool heat pump work, and do heat pumps work in Texas winters?
A pool heat pump works like an air conditioner in reverse. DOE describes it this way: pool water flows through the pump and filter and then the heater. A fan pulls outside air across an evaporator coil, where liquid refrigerant absorbs heat and becomes a gas. A compressor makes that gas hotter, and a condenser transfers the heat into the pool water. The refrigerant then cycles back to start again. Higher efficiency units usually use scroll compressors.
Because it moves heat instead of making it, a heat pump delivers more heat than the electricity it uses. Efficiency is measured as coefficient of performance (COP). DOE says COPs usually range from 3.0 to 7.0, meaning 3 to 7 units of heat for each unit of electricity. The federal test is run at 80 F air, 63% humidity and 80 F water, so real-world COP is lower on cool, dry days.
The cold-weather limit
DOE says heat pumps work efficiently as long as outdoor air stays above the 45 F to 50 F range. Below that, they lose efficiency and some shut down. What that means by region:
- Miami and South Florida: heat pumps can keep pools warm almost all year.
- Tampa, Orlando: heat pumps cover most of the year; a few cold nights may slow them.
- Jacksonville and North Florida: heat pumps work well spring through fall; winter cold fronts limit them.
- Houston and San Antonio: good spring-to-fall performance; winter heating is weaker on cold days.
- Austin and Dallas: heat pumps extend the season, but true winter swimming usually needs gas or a large cover-and-heater combination.
For winter swimming in North Texas, a gas heater or hybrid setup is more realistic. For a spa used year-round, gas heats in minutes rather than hours.
Gas pool heaters: natural gas vs propane
DOE calls gas the most popular way to heat pools. Gas heaters burn natural gas or propane, and the hot combustion chamber heats water passing through a heat exchanger. DOE says they are most efficient when heating pools for short periods, ideal for quick heating, a good choice for pools not used regularly, and able to hold any temperature regardless of weather.
- Efficiency: federal law has required new gas pool heaters to reach at least 82% thermal efficiency since April 16, 2013 (10 CFR 430.32(k)). DOE notes some models reach 89% to 95%.
- Sizes: gas pool heater outputs range from 75,000 to 450,000 Btu per hour.
- Life: with proper installation and maintenance, DOE says gas pool heaters typically last five or more years. Scale in the burner or heat exchanger cuts efficiency over time.
- Natural gas vs propane: natural gas needs a utility line to the house. If there is none, propane from a tank is the option. Fixr's 2025 guide notes propane is more expensive but available in more places.
How much does a more efficient gas heater save?
DOE gives a formula for replacing an old gas heater: current annual cost x [1 - (current efficiency / new efficiency)]. Example: if you spend $1,000 a year with a 70% efficient heater and switch to a 95% model, you save $1,000 x (1 - 0.70/0.95) = about $263 a year. DOE's own table shows the same thing: for every $1,000 you spend at 55% efficiency, a 95% heater saves $420.
Do solar pool heating panels work in Texas and Florida?
Yes, and DOE calls solar pool heating one of the most cost-effective uses of solar energy in some climates. A solar pool heater has collectors (panels), the pool's filter and pump, and a flow control valve that sends water through the collectors when they are warmer than the pool. In hot climates, the same collectors can cool the pool by running water through them at night.
Types of collectors
- Unglazed (heavy rubber or plastic with UV inhibitors): cheaper, common for pools used when it is above freezing.
- Glazed (copper tubing on an aluminum plate with tempered glass): costlier, better in cooler weather, and usable year-round in many climates.
Both need freeze protection if used in cold conditions, which matters in Texas.
Sizing
DOE says collector area should equal 50% to 100% of the pool's surface area. Its example: a 15 by 30 foot pool in Florida typically needs collectors equal to 100% of its surface, or 450 square feet, for year-round use. A pool cover can reduce the collector area you need.
Orientation and tilt
True south is best, but collectors can face up to 45 degrees east or west of south without a big loss. Summer-only systems work best tilted at your latitude minus 10 to 15 degrees; year-round systems at your latitude. DOE notes that mounting flat on a roof at a less-than-ideal angle usually does not cut performance much.
Cost and life
DOE says a solar pool heating system usually costs $2,500 to $4,000 to buy and install, with payback of 1 to 7 years depending on local fuel costs and sun, and should run 10 to 20 years with maintenance. Fixr's 2025 guide gives $2,500 to $7,000 installed, with 4 panels covering about 290 to 450 square feet of pool for $2,500 to $3,250 and 10 panels covering about 650 to 800 square feet for $5,500 to $7,000. Use the higher, newer range for budgeting.
Ratings
DOE points to the Solar Rating and Certification Corporation (SRCC), which rates solar pool heaters under its OG400 standard and keeps a directory of certified collectors. Compare collectors by their rated Btu per square foot per day; DOE says ratings within 25 Btu/(ft2 day) of each other should be considered about the same.
One catch: your pump may need to work harder to push water up to roof panels. DOE says you may need a larger pump or a separate smaller one. Austin Energy's pool pump rebate excludes existing pools with solar heating, so check rebate rules if you plan both.
How much does it cost to heat a pool per month in Texas and Florida?
DOE published annual heating cost tables for a 1,000 square foot outdoor pool in several cities, including Miami and Dallas. The tables are a useful starting point, but they used older energy prices: $0.1301 per kWh for the heat pump table (with a seasonal average COP of 5.0) and $0.80 per therm of natural gas for the gas table (80% efficient heater, uncovered 8 hours a day). We rescaled them to 2026 prices.
Heat pump: DOE annual cost and 2026 update
| City and season | Water temp | DOE cost, no cover | DOE cost, with cover | Updated to 2026 average rate, with cover |
|---|---|---|---|---|
| Miami, Jan. 1 to Dec. 31 | 78 F | $1,499 | $293 | about $338 (Florida 14.99 cents/kWh) |
| Miami, Jan. 1 to Dec. 31 | 80 F | $1,989 | $409 | about $471 |
| Miami, Jan. 1 to Dec. 31 | 82 F | $2,514 | $559 | about $644 |
| Dallas, Apr. 1 to Oct. 31 | 78 F | $491 | $123 | about $150 (Texas 15.91 cents/kWh) |
| Dallas, Apr. 1 to Oct. 31 | 82 F | $1,690 | $279 | about $341 |
How we updated it: DOE cost x (2026 EIA rate / $0.1301). For Florida that factor is about 1.15; for Texas about 1.22. Example: $409 x 1.152 = $471. Dividing a year-round Miami figure by 12 gives a rough monthly number: about $39 a month at 80 F with a cover, or about $191 a month uncovered ($1,989 x 1.152 / 12). DOE's Dallas row shows an unusual jump between 78 F and 80 F, so we did not use the 80 F Dallas figure.
Gas: DOE annual cost and 2026 update (Dallas)
| Dallas, Apr. 1 to Oct. 31 | DOE cost at $0.80/therm | At Texas March 2026 price (about $2.37/therm) | At Texas August 2026 price (about $3.55/therm) |
|---|---|---|---|
| 80 F, no cover | $1,920 | about $5,690 | about $8,520 |
| 80 F, with cover | $280 | about $830 | about $1,240 |
How we updated it: EIA reports Texas residential natural gas at $24.61 per thousand cubic feet in March 2026 and $36.84 in August 2026. Using a common conversion of about 10.37 therms per thousand cubic feet (our assumption; your utility's bill shows its exact factor), that is about $2.37 and $3.55 per therm. Summer residential gas prices per unit run high partly because fixed charges are spread over less gas use. EIA did not report a Florida residential gas price for those months, so we did not update the Miami gas row. Use your own bill's total cost per therm.
What the numbers say
- With current prices, a heat pump runs far cheaper than gas for regular swimming in both states.
- A cover cuts costs by roughly 75% to 85% in DOE's tables. That is a bigger saving than any heater choice.
- Every extra degree costs more. DOE says each degree adds 10% to 30% to heating energy.
- Gas still wins for heating a spa for one evening, because it heats fast and you pay only for the hours used.
Gas heater vs heat pump: which is cheaper to run?
For steady heating, the heat pump nearly always wins. DOE's comparison table: if an electric resistance heater costs $1,000 a year at $0.1301 per kWh, a heat pump with a 5.0 COP costs about $200 for the same heat, and a 55% efficient gas heater at $1.09 per therm costs about $1,000. That 55% figure is an old baseline; a new gas heater must be at least 82% efficient.
You can compare for your own home with this method:
- Cost per million Btu from electricity in a heat pump = (your price per kWh / COP) x 293. Example: $0.1591 / 4 x 293 = about $11.65.
- Cost per million Btu from gas = (your price per therm / efficiency) x 10. Example: $2.37 / 0.84 x 10 = about $28.21.
(One million Btu equals about 293 kWh or 10 therms.) In that example, gas costs more than twice as much per unit of heat. A heat pump's COP drops in cold air, so on a 45 F night the gap shrinks. Propane usually costs more per unit of heat than natural gas, which widens the gap further.
How much does a pool heater cost to install?
Fixr's pool heater cost guide (updated January 31, 2025) gives national installed prices. Local prices vary, and the biggest wild cards are gas line runs and electrical upgrades.
| Type and size | Pool surface area | Installed (Fixr, 2025) |
|---|---|---|
| Heat pump, 70,000 to 85,000 Btu | 280 to 450 sq ft | $2,500 to $4,000 |
| Heat pump, 110,000 to 117,000 Btu | 450 to 650 sq ft | $3,500 to $5,000 |
| Heat pump, 137,000 to 141,000 Btu | 650 to 800 sq ft | $4,000 to $6,500 |
| Gas, 100,000 to 150,000 Btu | 290 to 395 sq ft | $1,500 to $3,000 |
| Gas, 250,000 to 300,000 Btu | 515 to 650 sq ft | $2,500 to $4,500 |
| Gas, 300,000 to 400,000 Btu | 650 to 850 sq ft | $3,000 to $5,500 |
| Solar, 4 panels (4 x 10 ft) | 290 to 450 sq ft | $2,500 to $3,250 |
| Solar, 8 panels | 515 to 650 sq ft | $4,500 to $6,500 |
| Electric resistance, 50,000 to 99,000 Btu | 290 to 400 sq ft | $1,000 to $4,000 |
Fixr's most common job is about $3,500 for a 250,000 Btu gas heater on a 648 square foot pool. Its high-end example is about $9,000 for an 8-panel solar system with a pool cover.
Add-ons to ask about: a dedicated circuit for a heat pump (often 230 volts), a new gas line or a larger gas meter, a propane tank and its setback rules, a concrete pad, venting clearances for gas units, a bypass valve, permits and inspections. Fixr's 2024 new-build guide separately lists electric heaters at $2,231 to $5,338 and solar heaters at $2,599 to $11,929 as add-ons for a new pool.
What size pool heater do I need?
DOE recommends having a trained pool professional do a proper sizing analysis. For a rough check, DOE gives the same formula for gas and heat pump heaters:
Btu per hour needed = pool surface area (sq ft) x temperature rise (F) x 12
- Pick your desired pool temperature.
- Find the average air temperature for the coldest month you plan to swim.
- Subtract to get the temperature rise.
- Calculate surface area (length x width for a rectangle).
- Multiply.
The formula assumes a 1 to 1.25 F rise per hour and a 3.5 mph average wind over the pool. For a 1.5 F per hour rise multiply by 1.5; for 2 F, by 2.0.
Example: Houston pool in March
A 15 x 30 foot pool has 450 square feet of surface. You want 82 F water, and you estimate the coldest month you will swim averages 62 F, a 20-degree rise. 450 x 20 x 12 = 108,000 Btu per hour. Heat pump sizes are listed by Btu and horsepower; DOE gives standard sizes of 3.5 hp/75,000 Btu, 5 hp/100,000 Btu and 6 hp/125,000 Btu. In this example, a unit around 110,000 to 125,000 Btu would be a reasonable starting point for the pro to verify.
DOE adds that windy sites, low humidity and cool nights need a larger heater. A screened Florida lanai cuts wind across the water, which helps. For public pools, Florida caps heated water at 104 F (rule 64E-9.008).
Undersizing means the pool never reaches temperature on cool days. Oversizing a heat pump costs more up front but can reach temperature faster. With gas, a larger heater heats faster and costs about the same per Btu to run.
Do pool heaters fall under federal efficiency standards?
Yes. Consumer pool heaters are covered under 10 CFR 430.32(k):
- Gas-fired pool heaters manufactured from April 16, 2013 until May 30, 2028 must have a thermal efficiency of at least 82%.
- From May 30, 2028, gas-fired and electric pool heaters (electric resistance and heat pump) must meet minimum integrated thermal efficiency (TEI) levels. TEI also counts standby and off-mode energy. The minimums are formulas based on a gas heater's certified input capacity or an electric heater's active electrical power.
DOE's 2023 final rule estimated average lifecycle cost savings for buyers of $1,130 for electric pool heaters and $80 for gas heaters, with simple paybacks of 0.5 and 2.3 years, and an average heater life of 11.1 years. In plain terms, the 2028 rule mostly pushes electric pool heaters toward heat pump technology and trims gas heater standby losses. If you buy before 2028, you can still choose any heater sold legally today.
Does a pool cover cut heating cost?
More than anything else you can buy. DOE explains why: evaporation is by far the largest source of pool energy loss. Raising a pound of water 1 F takes 1 Btu, but each pound of 80 F water that evaporates takes 1,048 Btu out of the pool. DOE says covering a pool when it is not in use is the single most effective way to reduce heating costs, with savings of 50% to 70% possible. Covers also reduce make-up water by 30% to 50% and chemical use by 35% to 60%, according to DOE.
Cover types:
- Bubble (solar) covers: the cheapest pool-specific cover; a transparent bubble cover may reduce the pool's solar heat absorption by 5% to 15%.
- Vinyl and insulated vinyl covers: heavier and longer-lasting.
- Opaque covers: may reduce solar gain by 20% to 40%.
- Automatic covers: the most convenient and the most expensive. Some run in tracks and can act as safety covers. In Florida, a pool with an ASTM F1346 safety cover can satisfy the barrier rules. Fixr's 2024 guide lists automatic covers at about $3,594 for a 300 square foot pool to $10,782 for a 900 square foot pool.
DOE adds a climate point: in warm, humid conditions, it may be better to leave the cover off during sunny days to collect solar heat, and put it on at night. In dry, windy weather, a transparent cover during the day usually helps. See alarms and covers for safety cover rules.
Heating an attached spa
Spas are where gas heaters earn their keep. A spa holds far less water than a pool, so a gas heater can bring it from pool temperature to hot-tub temperature quickly, and you only pay for the hours you use it. DOE's description of gas heaters fits: most efficient for short periods, ideal for quick heating, and able to hold any temperature regardless of weather.
Common setups in Texas and Florida:
- Gas only: one gas heater serves both pool and spa through valves. Simple and fast, but expensive if you also heat the pool for weeks at a time.
- Heat pump plus gas (hybrid): the heat pump keeps the pool warm cheaply, and gas boosts the spa on demand. Some automation systems can choose the heater by air temperature.
- Heat pump only: works for spas in South Florida, but heat-up is slow, so plan ahead or keep the spa warm with a cover.
A tight spa cover matters as much as the heater. Keep spa water at or below the limit your equipment and local rules allow; Florida caps heated public pool water at 104 F. Our hot tub and spa guide covers temperature safety.
Heat pump placement, noise and the water you see under it
Where the heat pump sits affects how well it works and how your neighbors feel about it.
- Airflow. A heat pump pulls heat from air, so it needs open space around the coil and top fan. Cramming it behind a solid wall or under a deck recirculates cold exhaust air and lowers efficiency. Follow the clearances in the manual.
- Noise. The fan and compressor sound like an air conditioner. Keep it away from bedroom windows and property lines; some cities and HOAs have equipment setback or noise rules.
- Condensation. A running heat pump pulls moisture from the air, and water can drip from the base. Owners sometimes mistake this for a leak. A simple check: if the water stops when the unit is off, it is likely condensation. If it continues, look for a plumbing leak.
- Pad and anchoring. Set the unit on a level pad. In hurricane areas, ask whether the installation needs tie-downs to meet your local code.
- Flood elevation. FBC R4501.4.2.1 requires pools in flood hazard areas to meet the flood provisions of the residential code. Ask whether equipment should sit above the expected flood level in your zone.
- Electrical. Most units need a dedicated circuit and must be bonded like other pool equipment. See pool electrical safety.
Heating screened, enclosed and indoor pools
Screen enclosures, common in Florida, cut wind across the water. DOE's sizing guidance says windy sites need larger heaters, so a screened pool may get by with a smaller unit or hold heat better. Screens also shade the water somewhat, which can reduce solar gain.
Indoor pools are different. DOE notes they still lose a lot of energy to evaporation and need ventilation to control indoor humidity, and that ventilated air must be conditioned, adding to energy costs. A cover on an indoor pool cuts evaporation and lets you reduce ventilation or shut off exhaust fans while covered. EPA's WaterSense guide adds that keeping indoor air warmer than the water can reduce evaporation. Indoor pool heating and dehumidification design is a job for a mechanical engineer or experienced contractor.
Check your electric panel, gas meter and roof before you choose
The heater you want may need upgrades that change the price:
- Heat pump: confirm your electric panel has room and capacity for a new dedicated circuit, usually 230 volts. A panel upgrade can add a lot to the job.
- Natural gas: pool heaters have high input ratings. Your existing gas meter and line size may not supply the heater plus the furnace, water heater and stove at once. Ask the installer to check gas capacity and line length.
- Propane: plan the tank location, size, setbacks and delivery access.
- Solar: check roof space facing south, east or west, roof age (replace an old roof before mounting panels), shading, and whether your pump can lift water to the roof.
Ask for these items to be listed separately in the quote so you can compare like for like.
Questions to ask before you buy a pool heater
- What Btu output did you size this for, and what temperature rise and coldest month did you assume?
- What is the unit's COP (heat pump) or thermal efficiency (gas), and at what test conditions?
- What is the lowest air temperature at which this heat pump will run efficiently?
- What minimum water flow does the heater need, and will my pump setting provide it?
- Does the quote include the circuit, gas line, pad, permit and inspection?
- Who holds the license for each part of the work, and what are the license numbers?
- What freeze protection does the heater have, and how do I drain it?
- What maintenance does the warranty require, and who must perform it?
- For solar: what is the SRCC OG400 rating of these collectors, and how many square feet of collector will I get compared with my pool's surface area?
- Does my HOA need to approve the equipment or panels?
Can I heat a pool with propane if there is no natural gas line?
Yes. Gas pool heaters run on natural gas or propane (liquefied petroleum gas, or LPG). You will need a tank sized for the heater's demand, regulators and piping, and the tank must meet setback and installation rules. Ask your gas supplier and the building department. In Texas, LPG system installers are licensed under Natural Resources Code chapter 113, and Occupations Code 1301.055 says those licensed LPG installers do not need a plumbing license for LPG system installation. In Florida, ask your county building department and the LP gas supplier which licenses apply to the tank and piping.
Propane usually costs more per unit of heat than natural gas. Run the per-million-Btu comparison above with your propane price before choosing propane for a pool you heat often. For many owners without natural gas, a heat pump plus a cover is cheaper to run, with propane reserved for a spa.
Who can install a pool heater or gas line in Texas and Florida?
Florida
- Florida's statute puts the installation of package pool heaters within the scope of commercial and residential pool/spa contractors, and lets swimming pool/spa servicing contractors reinstall or add pool heaters (s. 489.105).
- Pool contractors' scope does not include direct connections to a sanitary sewer or potable water lines, and section 489.117(4)(e) says pool contractor rules do not expand their scope into plumbing or electrical work that needs a separate license.
- A heat pump's new circuit is electrical work for a licensed electrical contractor (part II of chapter 489).
- A Florida solar contractor's scope includes swimming pool solar heating systems, but other licensed contractors may do that work if it is within their own scope.
- For gas piping, ask your building department which license it accepts, and verify on MyFloridaLicense.com.
Texas
- Texas defines plumbing to include piping used to "supply, distribute, circulate, or recirculate water, other liquid, or gas" (Occupations Code 1301.002). Plumbers are licensed by the Texas State Board of Plumbing Examiners (TSBPE), which offers a public license search.
- A property owner does not need a plumbing license to do plumbing in their own homestead (1301.051), but cities still require permits and inspections for gas work.
- LPG system installation is licensed under Natural Resources Code chapter 113, not the plumbing law.
- The heat pump's electrical connection needs a TDLR-licensed electrician, or a residential appliance installer working for a licensed contractor for connection to an existing circuit (Occupations Code ch. 1305).
Florida's residential code also has heater rules any installer must follow: heaters must bear the label of a recognized testing agency and account for combustion air, venting and gas supply; a permanent bypass or antisiphon device must keep water in the heater when the pump stops; heaters in a pit need drainage; and heaters need flanges or unions next to them (FBC R4501.14).
Freeze protection and heaters: lessons from February 2021
The National Weather Service's Houston/Galveston office reports that the February 2021 winter storm brought hard freezes for days, with the City of Houston at 13 F and Houston Intercontinental Airport at 12 F on February 16, College Station at 5 F, and widespread power outages lasting several days. Broken pipes were among the impacts.
Heaters are especially vulnerable because water sits inside the heat exchanger. If the pump stops during a freeze, that water can freeze, expand and crack the exchanger, headers or plumbing. Steps before a hard freeze:
- Make sure your pump or automation freeze protection is on. Federal rules ship it with defaults no higher than 40 F, 1 hour of run time before rechecking, and half speed, which may not protect long pipe runs.
- Keep water moving through the heater. Running a gas heater at a low setpoint during a freeze can help, but only with power and gas.
- If a long outage is likely, ask your pool pro how to drain the heater, pump and filter. Many heaters have drain plugs.
- Solar collectors need freeze protection or must drain back to the pool.
- After the freeze, check for leaks before restarting the heater.
For storm damage and insurance steps, see hail and freeze pool damage in Texas.
Is a heat-cool heat pump worth it in South Florida?
DOE notes that some heat pump models can also cool a pool in hot weather. In Miami, Fort Lauderdale and Tampa, summer pool water can feel like bath water, especially in shallow pools in full sun. A heat-cool unit reverses its cycle to pull heat out of the water.
When it makes sense:
- You swim mostly in summer and the water gets too warm.
- The pool is shallow, unshaded or in a screened enclosure that traps heat.
- You want one unit for both winter heating and summer cooling.
What to check: cooling runs the compressor during the hottest, most expensive hours, so it adds to your bill. Ask the installer for cooling capacity at summer conditions, not just heating capacity. A solar system can also do some night cooling, DOE says, by running water through the collectors after dark.
How long do pool heaters last, and why does mine keep shutting off?
Lifespan. DOE says heat pump pool heaters can last 10 or more years with proper installation and maintenance, gas pool heaters typically five or more years, and solar systems 10 to 20 years. DOE's 2023 rulemaking used an average heater lifetime of 11.1 years. Fixr says electric resistance heaters last five to ten years.
Maintenance. DOE suggests an annual tune-up. Heat pumps have many moving and electrical parts and may need periodic service by an air conditioning technician. Gas heaters build scale in the burner and heat exchanger, so keep water chemistry balanced.
Common shut-off causes
| Symptom | Common causes |
|---|---|
| Heater runs briefly then stops | Low water flow from a dirty filter, full baskets or a pump set too slow; pressure switch fault |
| Heat pump stops on cool mornings | Air below the unit's operating limit; defrost cycle; low refrigerant |
| Gas heater will not light | Gas supply off, ignition fault, blocked vent or burner tray, wet components after rain |
| High-limit or overheat error | Low flow, bypass valve set wrong, scale buildup |
| Heater cycles with the automation | Schedule or setpoint conflict, flow switch fault |
Start with flow: clean the filter and baskets and check the pump speed. If the problem continues, call a licensed technician. Do not bypass safety switches.
Solar collectors and HOA rules in Texas and Florida
Florida. Statute 163.04 says no deed restriction, covenant or similar agreement may prohibit or have the effect of prohibiting solar collectors or other renewable energy devices, and local ordinances may not ban them either. An HOA may choose the specific roof location, but only among roofs facing south or within 45 degrees east or west of due south, and not in a way that impairs the collectors' effective operation. The statute does not name pool heaters specifically, so if your HOA objects to pool panels, ask an attorney how it applies.
Texas. Property Code 202.010 bars HOA rules that prohibit or restrict a solar energy device, with exceptions. An HOA may still prohibit a device that, for example, extends above the roofline, sits somewhere other than the roof or a fenced yard or patio, does not follow the roof slope, has visible frames or piping in a non-standard color, is taller than the fence in a yard, voids warranties, or was installed without prior HOA approval. The definition of "solar energy device" is borrowed from Tax Code 171.107, so confirm with your HOA or an attorney whether pool heating panels qualify.
See our HOA pool approval guide for how to submit plans.
City-by-city: what usually works where
These are general patterns based on DOE's 45 F to 50 F heat pump guidance and the seasons DOE used in its cost tables (Miami year-round; Dallas April through October). Your microclimate, shade and wind matter, so treat this as a starting point for a conversation with a pool pro.
| City | Typical heating goal | Options that commonly fit |
|---|---|---|
| Miami | Comfortable water in the cooler months; cooling in late summer | Heat pump or heat-cool heat pump; solar; cover |
| Tampa and Orlando | Extend into winter | Heat pump plus cover; solar on a good roof; gas for spas |
| Jacksonville | Spring and fall extension; occasional cold fronts | Heat pump for shoulder seasons; gas for winter or spa |
| Houston and San Antonio | Start earlier in spring, swim later in fall | Heat pump; gas for spas and cold snaps; freeze protection |
| Austin | Season extension; drought-aware water use | Heat pump plus cover; solar; gas for spa |
| Dallas | April to October comfort; winter mostly closed | Heat pump for the season; gas if winter swimming is a must |
Pool heating myths
- "Letting the pool cool down and reheating it costs more." DOE calls this a myth. Turning the heater down or off when you will be away for several days saves energy.
- "A bigger heater costs more to run." For gas, a larger heater heats faster and burns about the same fuel per Btu delivered. What drives cost is how much heat you lose, which a cover controls.
- "Heat pumps do not work in Texas." They work well in mild and warm weather. They struggle when air falls below about 45 F to 50 F, so they are a season-extender in North Texas rather than a winter solution.
- "Solar only works in the desert." DOE says solar pool heaters use both direct and diffuse sunlight, and an unshaded site facing generally south is a good candidate.
- "A cover blocks the sun's heat." DOE says transparent bubble covers reduce solar absorption by only 5% to 15%, while stopping the evaporation that causes most heat loss.
Ways to cut heating costs without a bigger heater
- Cover the pool whenever it is not in use. DOE says savings of 50% to 70% are possible.
- Lower the setpoint. DOE notes the American Red Cross recommends 78 F for competitive swimming; young children and older adults may want 80 F or higher. Each degree adds 10% to 30% to heating energy.
- Turn the heater down or off when you will not swim for several days. DOE calls it a myth that reheating uses more energy than you save.
- Block the wind. DOE suggests trees, shrubs or a fence that do not shade the pool or create turbulence.
- Turn off waterfalls and fountains when not in use; EPA notes surface turbulence increases evaporation.
- Run the heater with the right pump speed. Too slow trips flow switches; too fast wastes pump energy.
- Keep chemistry balanced to avoid scale in heat exchangers.
For the pump side of the bill, see variable-speed pumps, and for water loss see pool energy and water use.
How to choose a provider
- Decide how and when you swim: daily, weekends, winter, spa only.
- Measure the pool's surface area and estimate the needed temperature rise.
- Run the sizing formula (area x rise x 12) and compare with installer quotes.
- Get your own electricity price per kWh and gas or propane price per therm from your bills.
- Compare running costs per million Btu for heat pump, gas and solar.
- Budget for a cover; it saves more than any heater upgrade.
- Check gas line, meter, propane tank and electrical capacity before choosing.
- Confirm permits and the installer's license (DBPR in Florida; TSBPE and TDLR in Texas).
- For solar, check SRCC OG400 ratings, roof orientation and HOA rules.
- Set freeze protection and learn how to drain the heater before a hard freeze.
- Schedule an annual heater tune-up and keep chemistry balanced.
- Keep the heater manual, warranty and permit records together.
Related swimming pool builders and contractors guides
- Are Single-Speed Pool Pumps Banned? Variable-Speed Pumps, the DOE Rules and Real Savings in Texas and Florida
- How Much Electricity and Water Does a Pool Use in Texas and Florida?
- Pool Alarms, Safety Covers and Door Alarms: Which Layers of Protection Work?
- How Do Hail and Hard Freezes Damage Texas Pools, and How Do You Protect Equipment, Covers and Plumbing?
- Hot Tubs and Spas in Texas and Florida: What Do They Cost, and What Rules Apply?
- Florida Pool Screen Enclosures: What Do They Cost, What Wind Codes Apply, and Will Insurance Pay After a Hurricane?
- Do You Need HOA Approval to Build a Pool? Architectural Review, Rules and Your Rights in Texas and Florida
- Is Pool Automation Worth It? What Smart Pool Controls Do, and How They Help in Texas Freezes and Florida Hurricanes
Swimming pool builders and contractors by state and city
Questions people ask
What is the best way to heat a pool in Florida?
For most Florida pools, an electric heat pump paired with a cover is the cheapest way to keep water warm, because Florida air usually stays above the 45 F to 50 F range where DOE says heat pumps stay efficient. Solar panels add low-cost heat on sunny roofs. Gas makes sense for spas or quick heating, especially in North Florida during cold fronts.
Can I use my pool heater during a power outage?
Heat pumps cannot run without power. Most gas heaters also need electricity for controls and ignition, and none can heat without the pump moving water. During long outages in a freeze, the bigger worry is protecting the heater from freeze damage. Ask your pool pro how to drain the heater and equipment if an extended outage is expected.
How long does it take to heat a pool?
DOE's sizing formula assumes a heater that raises water about 1 to 1.25 F per hour. Gas heaters heat fastest; heat pumps and solar are slower and steady. A pool that has cooled by 10 degrees may take many hours with a heat pump. Keeping a cover on and holding a steady setpoint avoids long heat-ups.
Is an electric resistance pool heater ever a good idea?
Rarely for a full pool. Electric resistance heaters turn each unit of electricity into one unit of heat, while a heat pump delivers 3 to 7. DOE's comparison shows a heat pump costing about one-fifth as much to run for the same heat. Resistance heaters can make sense for very small spas. From May 30, 2028, electric pool heaters must meet federal TEI minimums.
Should I heat my pool in Texas in the winter?
It depends on how often you swim and your fuel. In Dallas and Austin, winter heating with a heat pump is limited on cold days, and gas heating an uncovered pool all winter can cost thousands. Many owners heat the spa with gas and keep the pool covered or closed. Run the cost math with your own gas price first.
Do I need a permit to install a pool heater?
Usually yes, especially when the job adds a gas line, a new circuit or roof-mounted solar panels. Florida's residential code sets heater installation rules, and Texas cities require permits for gas and electrical work. Your installer should pull the permit; ask for a copy and the final inspection.
Does a solar cover really heat the pool?
A bubble or solar cover mostly saves heat by stopping evaporation, which DOE calls the largest source of pool energy loss. A transparent bubble cover lets most sunlight through, reducing solar absorption by only 5% to 15%. EPA says solar covers reduce evaporation by 50% to 95% when in use, depending on shape and coverage.
What temperature should I keep my pool?
DOE says pool temperatures typically range from 78 F to 82 F. The American Red Cross recommends 78 F for competitive swimming, while young children and older adults may want 80 F or higher. Florida public pools with heaters may not exceed 104 F, which is mainly a spa limit. Each added degree raises heating cost 10% to 30%.
Will a heat pump raise my electric bill a lot?
It will add to your bill whenever it runs, but less than you might expect for the heat delivered. Using DOE's Miami table updated to Florida's August 2026 average rate, a 1,000 square foot pool held at 80 F all year with a cover costs about $471 a year to heat, or about $39 a month. Without a cover, the same pool costs about $2,290 a year.
Can I combine solar panels with a heat pump?
Yes. Many owners let solar collectors do most of the work on sunny days and use a heat pump or gas heater to top off on cloudy or cool days. Automation can switch between them based on collector and water temperature. DOE notes a cover reduces the collector area needed, which can lower solar costs.
Do I need a separate heater for a hot tub next to my pool?
Not always. An attached spa that shares the pool's plumbing usually shares its heater, with valves switching water between them. A separate portable hot tub has its own built-in electric heater. If you heat the spa often and the pool rarely, a gas heater for the spa and a cover for the pool is a common, cost-conscious setup.
Sources
- DOE Energy Saver: Heat Pump Swimming Pool Heaters (archived June 1, 2024)
- DOE Energy Saver: Gas Swimming Pool Heaters (archived August 5, 2021)
- DOE Energy Saver: Solar Swimming Pool Heaters (archived June 1, 2024)
- DOE Energy Saver: Swimming Pool Covers (archived June 1, 2024)
- DOE Energy Saver: Managing Swimming Pool Temperature for Energy Efficiency (archived 2024)
- 10 CFR 430.32 Energy and water conservation standards, paragraph (k) Pool heaters (eCFR)
- DOE: Energy Conservation Standards for Consumer Pool Heaters, final rule (2023)
- EIA Electric Power Monthly Table 5.6.A (August 2026)
- EIA: Texas Natural Gas Prices
- EIA: Florida Natural Gas Prices
- Fixr: Pool Heater Installation Cost (updated January 31, 2025)
- Fixr: Solar Pool Heater Installation Cost (updated January 31, 2025)
- Fixr: Cost to Build a Swimming Pool (updated January 25, 2024)
- EPA WaterSense: Jump Into Pool Water Efficiency (2022)
- NWS Houston/Galveston: February 2021 Winter Storm
- Florida Building Code, Residential 2023 Chapter 45
- Rule 64E-9.008, F.A.C.
- Fla. Stat. 489.105 (2026)
- Fla. Stat. 489.117 (2026)
- Fla. Stat. 163.04 Energy devices based on renewable resources (2026)
- Texas Property Code Chapter 202 (202.010 solar energy devices)
- Texas Occupations Code Chapter 1301: Plumbers
- Texas State Board of Plumbing Examiners
- Texas Occupations Code Chapter 1305: Electricians
- Austin Energy: Pool Pump Rebate
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


