Local Guide · Swimming pool builders and contractors
How Much Electricity and Water Does a Pool Use in Texas and Florida?
The pump is the biggest electric load, heating can be bigger, and evaporation is the biggest water loss. Here are DOE and EPA numbers worked out at 2026 Texas and Florida electricity prices, a gallon calculator, evaporation math, and the changes that cut use the most.
A pool's pump can use up to a few thousand kWh a year, DOE says. At August 2026 average rates (15.91 cents per kWh in Texas, 14.99 cents in Florida), the 3,000 kWh-a-year Florida pool in a DOE-cited study costs about $450 to $477 a year to pump, and about $108 to $115 after downsizing the pump and cutting run time. For water, EPA estimates an uncovered 500-square-foot pool loses 12,000 to 31,000 gallons a year to evaporation. A cover is the biggest saver for both.
Key facts
- DOE: a pool pump can be a home's second-largest electricity user after air conditioning, consuming up to a few thousand kWh a year.
- In a Florida Atlantic University study of 120 pools cited by DOE, a typical Florida pool used about 3,000 kWh a year for pumping; downsizing and cutting run time together dropped it to 720 kWh.
- EIA: average residential electricity cost 15.91 cents per kWh in Texas and 14.99 cents in Florida in August 2026.
- EPA WaterSense: depending on climate, an uncovered 500-square-foot pool could lose 12,000 to 31,000 gallons a year to evaporation, more if heated.
- EPA: solid covers can reduce evaporation by more than 90% when in use; solar (bubble) covers 50% to 95%; liquid evaporation suppressants about 15%.
- DOE: pool covers reduce make-up water needs by 30% to 50%, chemical use by 35% to 60%, and heating costs by 50% to 70%.
- DOE: evaporation is by far the largest source of pool energy loss; each pound of 80 F water that evaporates removes 1,048 Btu.
- EPA, citing the California Urban Water Conservation Council: about 23% of quantifiable pool water use goes to filter backwashing.
- EPA's 2016 Residential End Uses of Water data: only 15% of pool owners have and regularly use a pool cover.
How much does a pool add to my electric bill?
Three things drive a pool's electric use: the pump, the heater (if electric) and everything else (lights, automation, salt cell, cleaner booster pump).
The pump
DOE says the pool pump is probably the largest electric motor in your home, and can consume up to a few thousand kWh a year, second only to air conditioning. A study of 120 Florida pools by Florida Atlantic University's Center for Energy Conservation, cited by DOE, found a typical Florida pool used about 3,000 kWh a year for pumping. We recalculated the study's results at 2026 prices:
| Scenario | kWh per year | Texas (15.91 cents) | Florida (14.99 cents) | Per month (Florida) |
|---|---|---|---|---|
| Original pump and schedule | 3,000 | $477 | $450 | about $37 |
| Smaller pump | 1,800 | $286 | $270 | about $22 |
| 60% less run time | 1,200 | $191 | $180 | about $15 |
| Both | 720 | $115 | $108 | about $9 |
Rates are EIA's August 2026 state averages. Your own rate may differ, so use the total on your bill divided by kWh used. Florida pools often run all year; in North Texas, pumps may run fewer hours in winter, so annual totals can be lower.
Heating
Heating can cost more than pumping. Using DOE's heat pump cost table for a 1,000 square foot pool in Miami at 80 F year-round, updated to Florida's 2026 average rate, heating costs about $2,290 a year uncovered and about $471 with a cover. See pool heaters and heat pumps for the full tables and the math.
Everything else
- Lights: LED pool lights use less power than older incandescent and halogen fixtures; run them on a timer.
- Booster pumps: pressure-side cleaners with a booster pump add a second motor; DOE regulates booster pumps with their own minimum efficiency.
- Salt cells and automation: small loads, but they run whenever the pump runs.
Do time-of-use rates matter for pool pumps?
If your plan charges more during certain hours, shift long pump runs outside those hours. Many Texas customers in deregulated areas (most of Houston and Dallas-Fort Worth) choose retail plans, some with time-based pricing. Austin Energy and CPS Energy customers buy from city-owned utilities with their own rate structures. In Florida, most homes are served by investor-owned utilities, cooperatives or city utilities, some of which offer time-based options. Check your plan documents. Even on a flat rate, a variable-speed pump running slowly for longer hours usually costs less than a fast short run, because power drops much faster than flow when a pump slows down.
How can I cut pool energy use?
- Use a pool cover. DOE calls it the single most effective way to cut heating costs (50% to 70% savings possible).
- Install a variable-speed pump and run it slow. Since September 29, 2025, most standard-size replacement pump motors must be variable-speed anyway. ENERGY STAR pumps cut energy 11% to 18% more, EPA says.
- Shorten run time sensibly. DOE suggests starting at 6 hours a day and adjusting in half-hour steps until water stays clean. Florida's residential code still requires new pools to be able to turn over in 12 hours or less.
- Lower plumbing resistance. DOE says a large filter (rated at least 50% above design flow), larger or shorter pipes and gentler elbows can cut pump electricity up to 40%.
- Keep baskets and filters clean. Clogged drains and filters make the pump work harder.
- Lower the heater setpoint. Each degree costs 10% to 30% more, DOE says.
- Turn off water features when no one is using them.
- Use LED lights on timers.
- Check for rebates. Austin Energy lists a $300 rebate for qualifying ENERGY STAR variable-speed pumps installed by a participating contractor; CPS Energy lists $50 per horsepower, up to $150.
See variable-speed pumps and the DOE rule.
How many gallons are in my pool?
One cubic foot holds about 7.48 gallons. Measure in feet and use the formula for your shape:
| Shape | Formula (gallons) | Example |
|---|---|---|
| Rectangle | Length x width x average depth x 7.48 | 16 x 32 x 5 x 7.48 = 19,149 |
| Round | Diameter x diameter x average depth x 5.87 | 24 x 24 x 4 x 5.87 = 13,524 |
| Oval | Length x width x average depth x 5.87 | 15 x 30 x 4.5 x 5.87 = 11,887 |
| Freeform | Split into rectangles and circles, or use surface area x average depth x 7.48 | 500 sq ft x 5 x 7.48 = 18,700 |
Average depth = (shallow depth + deep depth) / 2 for a pool with an even slope. For a pool with a long flat shallow area and a short deep hopper, split it into sections.
Gallons per inch of water level: surface area in square feet x 0.623. A 500 square foot pool holds about 312 gallons per inch. That number makes evaporation and leak math easy.
Knowing your gallons matters for chemical doses, salt additions and pump sizing. See pool water chemistry.
How much water does a pool lose to evaporation?
EPA's WaterSense program estimates that, depending on climate, an uncovered 500-square-foot pool could lose between 12,000 and 31,000 gallons a year to evaporation, and more if the pool is heated. Fixr's pool maintenance guide (updated January 31, 2025) puts typical water loss at about 1/4 inch per day from evaporation, splashing and swimmers getting in and out.
Using our gallons-per-inch rule, 1/4 inch a day on a 500 square foot pool is about 78 gallons a day, or roughly 28,000 gallons over a year if that rate held every day. Real loss swings by season.
What drives evaporation (DOE and EPA)
- Water temperature: warmer water evaporates faster, so heated pools lose more.
- Air humidity: drier air pulls more water.
- Wind: wind across the surface speeds evaporation.
- Sun: outdoor pools absorb 75% to 85% of the solar energy hitting the surface, DOE says, warming the water.
- Turbulence: fountains, waterfalls and splashing add surface area and spray.
Texas vs Florida
DOE explains that higher temperature and wind and lower humidity increase evaporation. That points to higher losses in drier, windier Central and West Texas summers (Austin, San Antonio and west) than in humid Houston, and generally lower losses in humid Florida. DOE notes that in warm, humid conditions the evaporation rate drops. We did not find a Texas or Florida state agency study with pool-specific evaporation rates by city, so use EPA's range and your own bucket test.
Evaporation or leak? The bucket test
EPA's do-it-yourself leak test compares your pool's loss with a bucket's:
- On a day without rain or heavy wind, shut down all pool systems (filtration, cleaners, automatic fills) and close the pool for 24 hours.
- Fill a 2.5- to 5-gallon bucket to about 1 inch from the top and set it on a step or bench so at least two-thirds is submerged and the water inside is a little higher than the pool level.
- Mark the water level inside the bucket and the pool level.
- After 24 hours, compare. If the pool dropped more than the bucket, the pool may have a leak.
EPA also suggests shutting off an automatic fill for 24 hours once every three months to check for leaks, and confirming the fill valve shuts off properly. See pool leak detection.
Does a pool cover reduce evaporation?
Yes, more than anything else. EPA's WaterSense guide gives these figures for covers in use:
| Cover type | Evaporation cut when in use (EPA) | Safety cover? |
|---|---|---|
| Solid, mesh or hybrid | Up to 95% | Yes, if certified |
| Solar (bubble cover, solar rings, thermal) | 50% to 95%, depending on shape and coverage | No |
| Liquid evaporation suppressant | About 15% | No |
EPA says solid covers can reduce evaporation by more than 90%. DOE says covers reduce make-up water by 30% to 50% and chemical use by 35% to 60%. Yet EPA notes that, in data from the 2016 Residential End Uses of Water study, only 15% of pool owners have and regularly use a cover. A cover saves nothing when it sits rolled up.
Safety note: only covers certified under ASTM F1346 count as safety covers. In Florida, a pool with an approved ASTM F1346 safety cover meets the residential barrier rule. EPA also notes some utilities have offered cover rebates of up to $200; check with your water utility. See alarms, covers and safety layers.
Does a screen enclosure reduce evaporation?
It likely helps. DOE says wind across the pool surface increases evaporation and suggests windbreaks such as trees, shrubs or fences, as long as they do not shade the pool or create turbulence. A Florida screen enclosure acts as a windbreak on all sides and also blocks leaves and debris. It also shades the water somewhat, which can lower water temperature and solar heat gain. We did not find a measured study of evaporation under Florida screen enclosures, so we cannot give a percentage. A cover still cuts evaporation far more than screening alone.
See screen pool enclosures in Florida.
How much water does backwashing use?
EPA, citing the California Urban Water Conservation Council, says about 23% of quantifiable pool water use goes to filter backwashing, and another 21% to controlling total dissolved solids by draining and replacing water. Backwash volume depends on filter size, flow and how long you run it until the water clears.
Ways to cut it:
- Use a cartridge filter; EPA calls it the most water-efficient because it needs no backwashing.
- Backwash only when filter pressure rises about 10 psi, per EPA.
- Consider glass media in a sand filter for shorter backwash cycles.
- Skim and vacuum by hand to keep debris out of the filter.
- If allowed, use backwash water that is not freshly chlorinated on the lawn, as EPA suggests (salt pools are different).
See pool filters.
How much does it cost to fill a pool?
The math is simple; the rate is local. Most utilities charge per 1,000 gallons, often in tiers that rise with use, plus wastewater charges that may or may not apply to pool fills.
- Find your gallons (see the calculator above).
- Find your utility's price per 1,000 gallons for the tier you will hit, from your bill or the utility's rate page.
- Cost = gallons / 1,000 x rate.
Illustration only: if a utility charged $8 per 1,000 gallons, filling a 19,000-gallon pool would cost 19 x $8 = $152, before any wastewater or tier charges. Your rate could be higher or lower, so use your own.
Before you fill:
- Check drought rules. Each Texas utility with more than 3,300 connections must keep a drought contingency plan, so rules vary. In Austin's Emergency Stage 5, no one may use water to fill, clean, rinse, supplement or maintain a pool, and new single-family pool permits are suspended in Stages 4 and 5. San Antonio Water System prohibits water waste at all times.
- Ask about pool-fill or sewer credits. Some utilities do not charge sewer fees on water that does not go down the drain; ask.
- Plan the fill with your builder. In Florida, final electrical and barrier inspections must be done before a new concrete pool is filled (FBC R4501.19).
See drought restrictions on filling pools.
Is a pool more water-efficient than a lawn?
You will see this claim online, often with a specific comparison. We did not find a Texas or Florida agency study that measures a pool against the lawn it replaces, so we cannot give a reliable answer. It depends on how much lawn the pool and deck replace, how much you irrigate, local rainfall, whether the pool is covered, how often you backwash and drain, and leaks.
What we can say from EPA's numbers: an uncovered 500-square-foot pool may lose 12,000 to 31,000 gallons a year to evaporation, and a solid cover can cut evaporation by more than 90% when in use. A covered pool with a cartridge filter and no leaks uses far less water than an uncovered pool with frequent backwashing. In drought-prone Central Texas, water utilities treat pools as discretionary use and can restrict them in severe stages, which suggests planning the pool's water use as carefully as the lawn's.
Pool water and energy at a glance: Texas vs Florida
| Factor | Texas | Florida |
|---|---|---|
| Average residential electricity, Aug. 2026 (EIA) | 15.91 cents per kWh | 14.99 cents per kWh |
| Pumping season | Year-round in Houston and South Texas; shorter in North Texas | Year-round in most of the state |
| Evaporation drivers | Hot, drier, windier summers in Central and West Texas | High humidity lowers evaporation; screen enclosures cut wind |
| Water restrictions | Utility drought plans (for example Austin's Stage 5 pool water ban) | Utility and water management district rules; ask locally |
| Freeze energy use | Freeze protection runs pumps on cold nights | Rare outside North Florida |
| Rebates confirmed (Nov. 2026) | Austin Energy $300; CPS Energy up to $150 for pumps | None confirmed on official utility pages |
How to choose a provider
- Calculate your pool's gallons and gallons per inch.
- Read your electric bill to find your real cost per kWh.
- Estimate your pump's yearly kWh: watts x hours per day x days / 1,000.
- Use a pool cover whenever the pool is not in use.
- Switch to a variable-speed pump and run it slow.
- Clean baskets and filters on time to keep pump energy down.
- Backwash only when pressure rises about 10 psi, or use a cartridge filter.
- Turn off fountains and waterfalls when no one is swimming.
- Run the EPA bucket test if the water level drops faster than expected.
- Shut off any auto-fill for 24 hours every three months to check for leaks.
- Check your utility's drought stage before filling or topping off.
- Ask your electric and water utilities about current pool rebates.
Related swimming pool builders and contractors guides
- Are Single-Speed Pool Pumps Banned? Variable-Speed Pumps, the DOE Rules and Real Savings in Texas and Florida
- Pool Heat Pump vs Gas Heater vs Solar: Which Heats a Texas or Florida Pool Best, and What Does It Cost?
- Drought Watering Restrictions and Pools: Can You Fill, Top Off or Drain a Pool in Texas and Florida?
- Is My Pool Leaking? How Do You Test for a Leak, What Does Detection Cost, and Who Pays?
- Sand vs Cartridge vs DE Pool Filter: Which Is Best, and How Do You Size, Clean and Replace It?
- Florida Pool Screen Enclosures: What Do They Cost, What Wind Codes Apply, and Will Insurance Pay After a Hurricane?
- Pool Alarms, Safety Covers and Door Alarms: Which Layers of Protection Work?
- Is a Pool Worth It? A Full-Cost, Lifestyle and Risk Checklist for Texas and Florida
Swimming pool builders and contractors by state and city
Questions people ask
How much does it cost to run a pool pump each month?
It depends on the pump, hours and rate. In the Florida study DOE cites, a typical pool used 3,000 kWh a year, which at Florida's August 2026 average of 14.99 cents is about $37 a month. After downsizing and cutting run time, the same pool used 720 kWh a year, about $9 a month. Multiply your pump's watts by hours, divide by 1,000 and multiply by your rate for your own number.
How much water should my pool lose each day?
Fixr's 2025 maintenance guide puts typical loss at about 1/4 inch per day from evaporation and splash-out, and it can be more in hot, dry, windy weather or with a heated pool. If you lose much more, or the loss continues with the pool covered, run EPA's bucket test to check for a leak.
Does a pool raise my water bill a lot?
The first fill is the biggest single use. After that, evaporation, backwashing and splash-out drive top-offs. EPA estimates an uncovered 500-square-foot pool may lose 12,000 to 31,000 gallons a year to evaporation alone. A cover and a cartridge filter cut those losses the most. Ask your utility whether sewer charges apply to water used for pool top-offs.
Do solar covers really work in Florida humidity?
Yes, for both water and heat. EPA says solar covers cut evaporation 50% to 95% when in use. DOE notes that in warm, humid weather evaporation is already lower, so leaving the cover off on sunny days to collect heat and putting it on at night can work well. In dry, windy weather, a transparent cover during the day usually helps.
Will a heated pool use more water?
Yes. EPA notes that heated pools lose more water to evaporation because warmer water evaporates faster. DOE explains that each pound of 80 F water that evaporates removes 1,048 Btu of heat, so evaporation raises both your water and heating bills. Covering a heated pool is the most effective fix for both.
What uses more electricity, my pool or my air conditioner?
Usually the air conditioner. DOE says the pool pump is often the second-largest electricity user in a home after air conditioning or a heat pump. An electric pool heater or heat pump running often can push a pool's total use higher, especially for an uncovered, heated pool.
Does freeze protection run up my bill in Texas?
It adds some use on cold nights, but it is cheap insurance against cracked pipes and equipment. Federal rules ship pumps with freeze protection set to start at no more than 40 F, run up to 1 hour before rechecking and run at no more than half speed. Adjust those settings for hard freezes, and remember that a pump running at half speed uses far less power than at full speed.
Is it cheaper to drain and refill or to keep treating old water?
Usually keeping and treating the water is cheaper and wastes less, which matters under Texas drought rules. EPA notes that about 21% of quantifiable pool water use goes to draining and replacing water to control dissolved solids. Options like reverse osmosis treatment, which EPA says can recover up to 85% of pool water in some mobile systems, avoid a full drain.
Sources
- DOE Energy Saver: Choosing, Installing, and Operating an Efficient Swimming Pool Pump (archived June 1, 2024)
- DOE Energy Saver: Swimming Pool Covers (archived June 1, 2024)
- DOE Energy Saver: Heat Pump Swimming Pool Heaters (archived June 1, 2024)
- DOE Energy Saver: Managing Swimming Pool Temperature for Energy Efficiency (archived 2024)
- EIA Electric Power Monthly Table 5.6.A (August 2026)
- EPA WaterSense: Jump Into Pool Water Efficiency (2022)
- Fixr: Pool Maintenance Cost (updated January 31, 2025)
- 10 CFR 431.485: Pool pump motor standards (eCFR)
- 10 CFR 431.465: Dedicated-purpose pool pump standards (eCFR)
- Austin Energy: Pool Pump Rebate
- CPS Energy: Pool Pump Rebate (ClearResult program page)
- Austin Water Drought Contingency Plan (2024)
- Austin Water: Drought Response
- SAWS: Stage 1 drought restrictions
- Florida Building Code, Residential 2023 Chapter 45
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


