New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Swimming pool builders and contractors

Pool Water Chemistry Explained: Chlorine, pH, Alkalinity, CYA and Calcium Hardness

The target numbers for chlorine, pH, alkalinity, calcium and stabilizer, the Florida and Texas public pool limits, and how Texas hard water and Florida rain change the game.

For a home pool, keep free chlorine in the CDC's typical 1 to 4 ppm range, raised as stabilizer rises (about 7.5 percent of CYA), and pH between 7.0 and 7.8. Common targets are alkalinity 80 to 120 ppm, calcium hardness 150 to 200 ppm and CYA 30 to 50 ppm. Florida and Texas public pools must stay at or below 100 ppm CYA and meet minimum chlorine levels set by state rule.

Key facts

  • CDC's home pool guidance gives a typical chlorine range of 1 to 4 ppm, bromine 3 to 8 ppm and pH 7.0 to 7.8 (CDC, May 2025).
  • Florida public pools must keep pH 7.0 to 7.8 and free chlorine 1 to 10 mg/L in conventional pools, 2 to 5 mg/L in spas (rule 64E-9.004).
  • Florida caps cyanuric acid at 100 mg/L in public pools, with 40 mg/L recommended, and 40 mg/L in spas (64E-9.004).
  • Texas law requires at least 1.0 ppm free chlorine in public pools and 2.0 ppm in spas (Health and Safety Code 341).
  • Texas public pools must not exceed 100 ppm CYA and must hold 2.0 ppm free chlorine until CYA drops below 100 (25 TAC 265.193(p)).
  • Texas public pools must run a balance test such as the LSI at least every 10 days (25 TAC 265.193(k)).
  • SAWS reports typical hardness of 15 to 20 grains per gallon from the Edwards and Trinity aquifers; Austin Water reported 70 to 126 ppm in 2025.
  • Swim University's rule of thumb sets free chlorine at about 7.5 percent of the CYA level.
  • Florida DOH may close a public pool if pH is below 7.2 or above 7.8 (64E-9.017).

Pool chemical levels chart: the numbers that matter

Pool water chemistry comes down to two jobs. The first is sanitizing: keeping enough chlorine (or bromine) in the water to kill germs and algae. The second is balancing: keeping pH, alkalinity and calcium where the water neither eats the pool surface nor leaves scale on it. Everything else on a test strip supports those two jobs.

There is no single legal standard for a backyard pool in Texas or Florida. Public pool rules are law, and they make a useful outer fence. The table puts the public pool limits next to the home-pool guidance we could confirm from named sources.

TestCDC home pool guidance (2025)Florida public pools, rule 64E-9.004Texas public pools, HSC 341 and 25 TAC 265.193Common home targets (River Pools, Swim University)
Free chlorineTypical range 1 to 4 ppm1 to 10 mg/L in conventional pools; 2 to 5 mg/L in spas; indoor pools max 5At least 1.0 ppm in pools, 2.0 ppm in spas; at least 2.0 ppm whenever CYA is over 100 ppm1 to 3 ppm (River Pools); about 7.5% of the CYA level (Swim University)
Bromine3 to 8 ppm1.5 to 6 mg/L in conventional poolsSee rule figureNot covered
pH7.0 to 7.87.0 to 7.8 (closure if below 7.2 or above 7.8 under 64E-9.017)See rule figure7.2 to 7.6
Total alkalinityNot statedMust be tested; no range in the ruleTest at least every 10 days80 to 120 ppm
Calcium hardnessNot statedMust be tested; no range in the ruleTest at least every 10 days150 to 200 ppm (River Pools)
Cyanuric acid (CYA, stabilizer)Not stated100 mg/L max, 40 recommended max; 40 max in spasMust not exceed 100 ppm; banned indoors30 to 50 ppm; 60 to 80 ppm for salt pools (Swim University)
ClarityNot stated0.5 NTU or less; main drain grate visible from deck8-inch black disk visible at deepest pointClear to the floor

Note: mg/L and ppm (parts per million) are the same thing for pool water. The CDC home pool page says chlorine and bromine become less effective when pH is too high or too low, and it tells owners to check disinfectant and pH at least twice a day, more often with heavy use. Most home owners test less often than that; at minimum, test two to three times a week and after storms or parties.

Free chlorine vs combined chlorine vs total chlorine

When you add chlorine to water, it forms hypochlorous acid, the form that kills germs. Test kits report it in three ways:

  • Free chlorine (FC) is the chlorine still available to sanitize. This is the number that matters most.
  • Combined chlorine (CC), also called chloramines, is chlorine that has already reacted with sweat, urine, sunscreen and other nitrogen waste. It sanitizes poorly and causes the sharp "chlorine smell" and red eyes.
  • Total chlorine (TC) is free plus combined. Combined chlorine equals total minus free.

Texas requires public pools to measure free chlorine with the DPD test method (25 TAC 265.193(g)), and Florida requires DPD test kits for free and total chlorine at every public pool (64E-9.004(10)). DPD is the pink-color test in most liquid kits. A home owner can use the same method. Test strips are convenient, but a liquid DPD or FAS-DPD drop kit gives more exact numbers.

Why does my pool smell like chlorine?

A strong smell usually means too little free chlorine, not too much. The odor comes from combined chlorine. If your total chlorine is well above your free chlorine, the fix is to raise free chlorine (shock) so it breaks the combined chlorine down, and to keep swimmers showering first. CDC tells swimmers to shower for at least 1 minute before getting in.

What is cyanuric acid (CYA) and how much is too much?

Cyanuric acid, sold as stabilizer or conditioner, shields chlorine from the sun. Without it, Texas and Florida sunshine burns off free chlorine within hours. With too much of it, chlorine becomes slow to kill germs and algae.

The limits

  • Florida public pools: 100 mg/L maximum, with 40 mg/L as the recommended maximum; spas 40 mg/L maximum (64E-9.004).
  • Texas public pools: must not exceed 100 ppm. When CYA is over 100 ppm, free chlorine must be raised to at least 2.0 ppm and held there, with daily testing, until CYA falls below 100 (25 TAC 265.193(p)). CYA and stabilized chlorine are banned in indoor pools, spas and therapy pools.
  • Home pools: Swim University suggests 30 to 50 ppm for traditional outdoor chlorine pools and 60 to 80 ppm for saltwater pools.

The chlorine to CYA ratio

Because CYA slows chlorine down, the right free chlorine level rises as CYA rises. Swim University's rule of thumb is free chlorine at about 7.5 percent of the CYA level. At 40 ppm CYA, that is about 3 ppm free chlorine. At 80 ppm CYA, it is about 6 ppm. CDC notes that disinfection takes longer when cyanuric acid is present.

CYA (ppm)Free chlorine at 7.5% of CYA (ppm)
30about 2.3
40about 3
50about 3.8
60about 4.5
80about 6
100about 7.5

Stabilizer buildup from trichlor tablets

Trichlor tablets and dichlor granules contain cyanuric acid, so every tablet adds a little more. CYA does not evaporate or burn off. In a Texas or Florida pool fed only tablets through a long summer, CYA keeps climbing. Rain overflow and splash-out remove some, but in a dry year the pool may lose water mainly to evaporation, which leaves the CYA behind.

Signs you have "chlorine lock" from high CYA: chlorine reads normal but algae keeps returning, or the pool needs more and more chlorine to stay clear.

How to lower CYA

Swim University says the only reliable fix is dilution: drain part of the water and refill with fresh water. As a rough guide, removing 10 percent of the water lowers CYA by about 10 percent. Check your utility's drought stage before you drain, and never drain fully without checking groundwater and the hydrostatic valve (see drought rules for pools). Then switch to an unstabilized chlorine, such as liquid sodium hypochlorite, so CYA stops rising.

pH: what it does and how to raise or lower it

pH measures how acidic or basic the water is on a scale of 0 to 14, with 7 neutral. Pool water is kept slightly basic. CDC's home range is 7.0 to 7.8, and Florida's public pool rule uses the same band. Most home guides aim for 7.2 to 7.6, the middle of that range.

  • pH too low (acidic): etches plaster, corrodes heater parts and metal, can sting eyes and skin.
  • pH too high (basic): chlorine works poorly, water turns cloudy, scale forms on tile and in heaters.

How do I lower pH?

Add an acid. The two common choices are muriatic acid (hydrochloric acid) and dry acid (sodium bisulfate). Follow the product label dose for your pool's gallons. Pour slowly in front of a return jet with the pump running, never into the skimmer, and never mix acid with chlorine products. Retest after the water has circulated for a few hours. Read our pool chemical safety guide before handling acid.

How do I raise pH?

Use soda ash (sodium carbonate) or, if alkalinity is also low, baking soda (sodium bicarbonate), which raises alkalinity more than pH. Aeration from fountains and waterfalls also pushes pH up slowly.

Why does my pH keep rising?

Saltwater chlorine generators, fresh plaster, high alkalinity and lots of splashing all drive pH up. That is normal. Many Texas and Florida owners add a small dose of acid every week. Saltwater pools often need acid more often. See saltwater pool systems.

Total alkalinity: the pH buffer

Total alkalinity measures dissolved bicarbonates and carbonates. It acts as a buffer that keeps pH from swinging. River Pools lists 80 to 120 ppm as a typical home range.

  • Low alkalinity: pH bounces up and down, plaster etches, metal corrodes.
  • High alkalinity: pH keeps drifting up, water clouds, scale forms.

How do I raise alkalinity?

Add sodium bicarbonate (baking soda) in measured doses, following the product label for your gallons. Add it with the pump running, broadcast across the deep end, and wait several hours before retesting.

How do I lower alkalinity?

Lowering alkalinity takes acid plus aeration: add acid to drop pH, then aerate (waterfalls, jets pointed up) to raise pH without raising alkalinity much. Repeat over several days. This is slow, which is why it pays not to overshoot when adding baking soda.

Calcium hardness and why it matters in Texas

Calcium hardness is the amount of dissolved calcium in the water. Plaster, pebble and quartz finishes are made with cement, which contains calcium. Water that is low in calcium tries to pull calcium out of the finish. Water that is too high leaves white scale on tile, in heaters and on salt cells.

Texas tap water is hard, and it varies a lot

UtilityReported hardnessAbout in ppm
San Antonio (SAWS), Edwards and Trinity aquifersTypically 15 to 20 grains per gallonabout 257 to 342 ppm (at 17.1 ppm per grain)
Austin Water, 2025 report70 to 126 ppm, average 93 ppm4.1 to 7.4 grains per gallon, average 5.4

SAWS says the calcium carbonate in Edwards and Trinity aquifer water is naturally occurring. Austin Water defines hardness as dissolved calcium and magnesium and gives the conversion of one grain per gallon to about 17.1 ppm. These are total hardness figures for drinking water. Pool calcium hardness tests measure calcium only, so test your own fill water.

What this means: a San Antonio pool may start out above the 150 to 200 ppm range that River Pools suggests, before evaporation concentrates it further. Each time the pool loses water to evaporation and is topped off, the minerals stay and more come in. Over a few Texas summers, calcium climbs. The usual fixes are to keep pH and alkalinity at the low end of their ranges to reduce scaling, use a sequestrant or scale inhibitor product, and partially drain and refill when levels get very high (timed with drought rules).

Florida water sources vary widely by utility. Check your utility's annual water quality report (Consumer Confidence Report), which lists hardness, and test the pool itself.

What is the LSI (Langelier Saturation Index)?

The Langelier Saturation Index is a single number that tells you whether water will dissolve calcium (corrosive) or deposit it (scaling). It combines pH, water temperature, calcium hardness, total alkalinity and total dissolved solids.

  • LSI near 0: balanced. The water neither eats the finish nor scales it.
  • Negative LSI: corrosive. Expect etching of plaster and damage to metal parts.
  • Positive LSI: scale forming. Expect white crust at the waterline, cloudy water and scaled heater and salt cells.

Texas requires public pools to run a chemical balance test such as the LSI at least once every 10 days and record it (25 TAC 265.193(k)). Home owners can use a free LSI calculator from a test-kit maker or pool supply store. Temperature matters: hot summer water tends toward scale, and cold winter water tends toward corrosion. A pool that is balanced in January in Houston may scale in August.

Should I shock my pool, and how often?

"Shocking" means raising free chlorine well above normal for a short time to burn off combined chlorine, kill algae and recover from heavy use. You do not need to shock on a fixed schedule if free chlorine stays in range and combined chlorine stays low. Shock when:

  • combined chlorine (total minus free) is high or the pool smells of chlorine;
  • you see algae, slime or cloudy water;
  • after a pool party or heavy use;
  • after a big rain or a storm that blew in debris;
  • after a fecal accident (see below).

Calcium hypochlorite ("cal-hypo") shock adds calcium, which matters in hard-water Texas. Liquid sodium hypochlorite adds no calcium and no CYA. Dichlor shock adds CYA. Choose the shock that does not push your highest number higher.

Can you swim right after shocking?

Wait until free chlorine drops back to a safe range. Florida's public pool rule lets swimming resume after breakpoint or algae treatment once free chlorine drops to 10.0 mg/L or less, and requires the pool to be closed during manual chemical addition and for at least 1 hour after (64E-9.004(2)). For a home pool, a cautious rule is to wait until free chlorine is back within the CDC's typical 1 to 4 ppm range, or at least within your CYA-adjusted target, and pH is 7.0 to 7.8.

Poop in the pool

CDC says to remove the poop with a net or bucket (do not vacuum it), then raise free chlorine to 2 ppm (or keep it there) with pH 7.5 or less for 30 minutes, and confirm the filter is working. CDC notes that its very-high-chlorine steps for diarrhea in public pools do not apply to backyard pools because of the chemical injury risk, and that disinfection takes longer when cyanuric acid is present.

Phosphates, metals and other extras

Do I need a phosphate remover?

Phosphates are plant food that comes from fertilizer runoff, leaves, pollen and some fill water. Phosphate removers are sold as algae prevention. Swim University's view is that you do not need to worry about phosphates or use a remover if you keep chlorine in range, because chlorine, not phosphate removal, prevents algae. Some Florida owners with frequent lawn runoff and enclosures full of debris still use them. Treat a remover as an optional extra, not a substitute for chlorine.

Metals

Copper and iron can stain plaster blue-green or brown. Sources include well water, copper algaecides and corroded heater parts from low pH. Florida caps copper at 1 mg/L in public pools (64E-9.004). If you fill from a well, test for metals first and use a metal sequestrant.

Salt

Saltwater pools are chlorine pools: the generator makes chlorine from salt. You still test free chlorine, pH, alkalinity, CYA and calcium. Follow the salt level on your generator's manual. Florida requires a specific test kit for sodium chloride at public pools that feed salt (64E-9.004(10)(a)).

Florida public pool chemical limits (Chapter 64E-9)

If you manage a condo, HOA, apartment or hotel pool in Florida, rule 64E-9.004, F.A.C., is the law your county health department inspects against. Key numbers:

ItemRequirement
pH7.0 to 7.8
Free chlorine1 to 10 mg/L conventional pools; 2 to 10 mg/L swim-up bars, wading pools, interactive fountains and similar; 2 to 5 mg/L spas; indoor conventional pools max 5 mg/L
Bromine1.5 to 6 mg/L conventional pools; 3 to 6 mg/L other pools
ORP (when controllers required)700 to 850 millivolts
Cyanuric acid100 mg/L max (40 recommended max); spas 40 mg/L max
Copper / silver / quaternary ammonium1 / 0.1 / 5 mg/L max
Clarity0.5 NTU or less, main drain grate visible from deck
TestingpH and disinfectant manually at least once every 24 hours; CYA weekly when stabilized chlorine is used; logs kept at the pool

Under rule 64E-9.017, the Department of Health may close a public pool for conditions including pH below 7.2 or above 7.8 or a main drain grate that cannot be seen. Notice the gap: 64E-9.004 lists 7.0 to 7.8 as acceptable, but 64E-9.017 lets DOH close a pool below 7.2. Operators should keep pH at 7.2 or higher to be safe. The Department of Health may also fine up to $500 per violation per day under chapter 514. See Florida public pool rules.

Note that pools serving 32 or fewer condo or cooperative units, or HOAs with 32 or fewer units or parcels, are exempt from most DOH supervision but still must meet water quality rules (s. 514.0115).

Texas public pool chemical rules (25 TAC 265.193)

Texas sets public pool water quality in Health and Safety Code chapter 341 and in DSHS rule 25 TAC 265.193. Key points:

  • Public pools must keep at least 1.0 ppm free chlorine and spas at least 2.0 ppm, or another DSHS-approved disinfectant (HSC 341.064(b)).
  • Disinfectants must be EPA-registered for pools and spas.
  • Free chlorine and bromine must be measured with the DPD method.
  • CYA must not exceed 100 ppm, and stabilized chlorine is banned indoors.
  • Water must be clear enough to see an 8-inch black disk at the deepest point.
  • Class A and B pools test disinfectant and pH every two hours while open; Class C pools (apartments, HOAs, hotels) with on-site staff test at least three times a day, and those without staff at least once a day.
  • Alkalinity, calcium hardness and a balance test such as LSI at least every 10 days.
  • Logs kept at least three years and produced within five business days if requested.
  • Chemicals may not be dispensed through skimmers.

The full range table is in the rule's Figure 265.193(c), which we could not load as text; check the current rule before setting operating ranges. Many Texas cities, including Houston, Dallas, Austin and San Antonio, also permit and inspect public pools. See Texas public pool rules.

Rain, heat and pollen: regional chemistry problems

Florida: rain dilution and pH swings

A heavy summer storm can add inches of rainwater in an hour. Rain is soft and slightly acidic, so it lowers alkalinity, calcium and CYA by dilution and can drop pH. It also washes in fertilizer, leaves and dirt that feed algae and use up chlorine. After a big rain in Miami, Tampa or Orlando: lower the water level if it is above the skimmer, test free chlorine, pH and alkalinity, and add chlorine first.

Texas: heat and evaporation

In a Dallas or San Antonio August, warm water and strong sun use chlorine fast, and evaporation concentrates calcium and dissolved solids. Test more often and keep CYA in range so sun does not strip chlorine.

Texas oak pollen and Hill Country caliche dust

Spring oak pollen in Central and North Texas floats as a yellow film that looks like mustard algae. Pollen skims off and does not cling to walls; algae does cling and returns after brushing. Caliche dust in the Hill Country and West Texas adds calcium and clouds water after wind storms. Run the filter longer and clean it more often. See the pool maintenance schedule.

How to test pool water correctly

  1. Pick a kit. A liquid drop kit with DPD or FAS-DPD for chlorine, plus pH, alkalinity, calcium and CYA tests, gives the best home results. Strips are fine for quick checks.
  2. Sample right. Take water from elbow depth, away from return jets and skimmers.
  3. Test in order. Free chlorine, combined chlorine, pH, alkalinity, then calcium and CYA weekly or monthly.
  4. Adjust in order. Alkalinity first, then pH, then chlorine. Add one chemical at a time with the pump running and wait before adding the next.
  5. Store reagents right. Texas rules require public pool test kits and reagents to be kept out of extreme heat and replaced on the maker's schedule. The same applies at home: a kit left in a hot Florida shed all summer gives bad readings.
  6. Write it down. A simple log shows trends, such as CYA creeping up, before they become problems.

A pool store water test is a good second opinion, but test the same day you collect the sample.

How to choose a provider

  • Buy a liquid DPD or FAS-DPD test kit that also tests pH, alkalinity, calcium and CYA.
  • Test free chlorine and pH several times a week, and after rain or heavy use.
  • Test alkalinity weekly and calcium and CYA monthly.
  • Adjust alkalinity first, then pH, then chlorine, one chemical at a time.
  • Set your free chlorine target from your CYA level.
  • Track CYA if you use tablets; switch to liquid chlorine when it climbs.
  • In hard-water Texas, keep pH and alkalinity near the low end and watch calcium.
  • In Florida, retest and rechlorinate after every heavy rain.
  • Store test reagents out of heat and replace them on schedule.
  • Keep a written log of every test and adjustment.

Related swimming pool builders and contractors guides

Swimming pool builders and contractors by state and city

Questions people ask

What should pool chemical levels be?

For a home pool, CDC gives a typical free chlorine range of 1 to 4 ppm and pH of 7.0 to 7.8. Common home targets are total alkalinity 80 to 120 ppm and calcium hardness 150 to 200 ppm (River Pools), and cyanuric acid 30 to 50 ppm, or 60 to 80 ppm in salt pools (Swim University). Raise free chlorine as CYA rises, about 7.5 percent of the CYA level.

What is the chlorine to CYA ratio?

Swim University's rule of thumb is to keep free chlorine at about 7.5 percent of the cyanuric acid level. At 40 ppm CYA, that is about 3 ppm free chlorine; at 80 ppm CYA, about 6 ppm. The ratio matters because CYA protects chlorine from sunlight but also slows how fast it kills germs and algae. CDC notes disinfection takes longer when CYA is present.

What is a safe CYA level, and what if it is too high?

Florida public pools may not exceed 100 mg/L, and 40 is the recommended maximum. Texas public pools may not exceed 100 ppm and must hold at least 2.0 ppm free chlorine until CYA drops below 100. For home pools, 30 to 50 ppm is a common target. If yours is too high, partially drain and refill, check drought rules first, and switch to unstabilized liquid chlorine.

Why does my pool smell like chlorine?

A strong chlorine smell usually means combined chlorine (chloramines), which forms when chlorine reacts with sweat, urine and body oils. It often means the pool needs more free chlorine, not less. Test free and total chlorine: if total is clearly higher than free, shock the pool to break down the chloramines, and ask swimmers to shower first. CDC suggests a 1-minute shower.

How do I lower pH in a pool?

Add muriatic acid or dry acid (sodium bisulfate) following the label dose for your pool size. Pour slowly in front of a return jet with the pump running, never in the skimmer, and never mix acid with chlorine. Wear goggles and gloves. Retest after a few hours of circulation. Aim for the middle of the 7.0 to 7.8 range CDC gives for home pools.

Is hard water a problem for Texas pools?

Yes, in many areas. SAWS reports typical hardness of 15 to 20 grains per gallon, about 257 to 342 ppm, from the Edwards and Trinity aquifers. Austin Water reported 70 to 126 ppm in 2025. Evaporation and top-offs concentrate calcium over time, causing white scale on tile and in heaters. Keep pH and alkalinity at the low end of their ranges, use a scale inhibitor, and dilute when levels get very high.

Can you swim right after shocking a pool?

Not right away. Wait until free chlorine falls back to a normal range. Florida's public pool rule lets swimmers return after a breakpoint or algae treatment once free chlorine is 10.0 mg/L or less, with the pool closed during manual chemical addition and for at least 1 hour after. For a home pool, wait until free chlorine is near your normal CYA-adjusted level and pH is 7.0 to 7.8.

What are public pool chemical limits in Florida and Texas?

Florida's rule 64E-9.004 requires pH 7.0 to 7.8, free chlorine 1 to 10 mg/L in conventional pools and 2 to 5 mg/L in spas, CYA no more than 100 mg/L, and clarity of 0.5 NTU or less. Texas requires at least 1.0 ppm free chlorine in pools and 2.0 ppm in spas, CYA no more than 100 ppm, DPD testing, and an 8-inch black disk visible at the deepest point.

How often should I test my pool water?

CDC tells home pool owners to check disinfectant and pH at least twice a day, and more often when the pool is busy. Many owners test chlorine and pH a few times a week as a practical minimum, plus after storms and parties. Test alkalinity weekly and calcium and CYA monthly. Texas public pools must test alkalinity, calcium and balance at least every 10 days.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration