New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Swimming pool builders and contractors

Sand vs Cartridge vs DE Pool Filter: Which Is Best, and How Do You Size, Clean and Replace It?

Every pool filter traps dirt, but sand, cartridge and DE filters differ in how fine they filter, how much water they waste, and how much work they take. Here are EPA and Florida code numbers, 2025 costs, pressure rules of thumb, backwash and drought rules, and DE dust safety.

DE filters trap the finest particles (about 5 microns per EPA) but cost the most and need fresh DE powder after each backwash. Sand filters are cheapest and simplest but filter coarsest (20 to 40 microns) and waste water when backwashed about weekly. Cartridge filters (about 10 microns) use the least water because they are hosed off instead of backwashed, which EPA calls the most water-efficient choice. In drought-prone Texas cities and septic areas of Florida, a properly oversized cartridge filter is often the practical pick.

Key facts

  • EPA WaterSense: sand filters remove particles of about 20 to 40 microns, cartridge about 10, DE and glass media about 5.
  • EPA WaterSense media life: sand 3 to 6 years, glass 7 to 15 years, DE grids 2 to 3 years, cartridges 2 to 4 years.
  • EPA: backwash is usually necessary when filter pressure rises about 10 psi above its clean reading.
  • EPA, citing the California Urban Water Conservation Council: about 23% of quantifiable pool water use goes to filter backwashing.
  • Florida Building Code, Residential R4501.20: filtration components must provide a complete turnover in 12 hours or less; DE filters may not exceed 2 gpm per square foot of filter area.
  • FBC R4501.20.1.1: rapid sand filters run up to 5 gpm per square foot; backwash flow must be at least 12 gpm per sq ft (rapid sand) or 15 gpm per sq ft (high-rate sand).
  • Florida public pools: maximum filtration rates of 15 (or 20 if approved) gpm per sq ft for high-rate sand, 3 for rapid sand, 0.375 for pleated cartridge and 2 for DE (rule 64E-9.008).
  • Fixr (updated January 31, 2025): pool filter installation averages $1,000 nationally, with a typical range of $500 to $2,000.
  • DOE: using a filter rated at least 50% above the pool's design flow lets you use a smaller pump and cut pumping energy.
  • OSHA: breathing crystalline silica dust can cause silicosis, lung cancer, COPD and kidney disease; EPA notes DE can be harmful if inhaled.

Which pool filter is best: sand, cartridge or DE?

A pool filter catches dirt, debris and some microorganisms as the pump pushes water through it. The three main types do the same job with different media. This table combines EPA WaterSense's 2022 pool guide and Fixr's January 2025 cost guide:

SandCartridgeDE (diatomaceous earth)Glass media (in a sand filter tank)
Filters down to (EPA)20 to 40 micronsAbout 10 microns (can vary)About 5 micronsAbout 5 microns
How you clean itBackwash about once a week (EPA)Remove and hose off; no backwashBackwash every 4 to 8 weeks, then add fresh DEBackwash; shorter cycles than sand
Water useHighestLowest (EPA: most water-efficient)MediumLower than sand
Media life (EPA)3 to 6 years2 to 4 yearsGrids 2 to 3 years7 to 15 years
Unit price, materials only (Fixr, 2025)$300 to $1,200$200 to $1,600$520 to $2,000$500 to $1,500
Main drawbackCoarser filtering, backwash wasteHands-on cleaning; cartridge costCost, DE handling, more partsMedia cost

A micron is one millionth of a meter. A smaller number means finer filtering. For reference, EPA notes that sand filters are the most common residential type because of low cost and easy care, while DE filters give the highest performance at the highest cost.

How to decide

  • Want the least water waste? Cartridge. This matters in Austin and San Antonio during drought stages and anywhere you pay for water or worry about discharge.
  • Want the clearest water? DE, if you can handle the extra steps and safety precautions.
  • Want the lowest price and least hands-on work? Sand, or sand upgraded to glass media.
  • Have lots of leaves, pollen or oak tassels? A large cartridge or a sand filter handles heavy loads; DE loads up faster.
  • Have a salt system? Fixr notes any of the three works with saltwater; cartridge filters reduce salty backwash water.

How each filter type works

Sand

Water enters the top of a tank filled with filter sand (Fixr describes it as special No. 20 silica sand) and works its way down. Dirt gets trapped between grains. Laterals at the bottom collect clean water. As dirt builds up, pressure rises, so you backwash: a multiport valve reverses the flow, lifting the sand and sending dirty water out the waste line. Florida's residential code requires the system to supply backwash flow of at least 12 gpm per square foot for rapid sand filters and 15 gpm per square foot for high-rate sand filters (R4501.20.1.1).

Cartridge

Water passes through a pleated polyester fabric element. Fine dirt sticks to the pleats. When pressure rises, you shut off the pump, open the tank, remove the cartridge and hose it off. No water goes to waste except the hose water. EPA notes that oversized cartridge filters cut water use further because they need cleaning less often.

DE (diatomaceous earth)

DE is a powder made from the fossilized shells of tiny organisms called diatoms. In the filter, it coats fabric-covered grids or fingers to form a fine, porous layer that catches very small particles. Florida's code calls this a "filter aid" and requires a way to add it so it coats the septum evenly (R4501.20.2.2). After backwashing, EPA says you must add fresh DE.

Glass media

Crushed, recycled glass can replace sand in many sand filter tanks. EPA says it filters to about 5 microns, allows shorter backwash cycles and lasts 7 to 15 years. Ask the filter maker whether your tank and valve are approved for glass.

What filter pressure is too high?

Every pressure filter has a gauge, and the gauge is your best maintenance tool.

  1. Record your clean pressure. Right after a backwash or cartridge cleaning, with the pump at your normal speed, write the reading on a tag or on the filter.
  2. Watch the rise. EPA says that when pressure increases by about 10 psi, a backwash (or cleaning) is usually necessary. Check your filter manual, since some makers give a different number.
  3. Compare at the same pump speed. With a variable-speed pump, pressure changes with speed, so always read it at the same setting.

What unusual readings can mean:

ReadingPossible causes
Rising fast after cleaningAlgae or heavy debris, pump too fast, cartridge or DE grid clogged with oils or scale, too much DE added
Higher than normal right after cleaningPartly closed return valve, clogged return line, worn or caked media, scale in a heater
Lower than normalClogged skimmer or pump basket, air leak on the suction side, low water level, torn cartridge or broken lateral letting water bypass the media
Gauge stuck or full of waterFailed gauge; replace it (they are inexpensive)

Safety first: pressure filters store energy. Florida's code requires a way to release internal pressure on pressure-type filters and lids designed for slow, safe release (R4501.20.1.3). Always turn off the pump and open the air relief valve before opening a filter, and never stand over the lid while restarting.

For public pools, Florida rule 64E-9.008 requires working air relief valves, influent and effluent pressure gauges with at least a 2-inch face reading 0 to 60 psi, and a sight glass where a backwash line is required.

How often should I clean my pool filter?

Clean or backwash based on pressure, not the calendar. EPA's guide gives typical intervals:

  • Sand: backwash about once a week.
  • Glass media: backwash about once a week, with shorter cycles than sand.
  • DE: backwash every 4 to 8 weeks, then add new DE.
  • Cartridge: clean when pressure rises; frequency depends on the cartridge and debris load.

DOE adds a balance point: backwashing too often wastes water, while not backwashing enough wastes energy by making the pump work harder. EPA suggests reducing filter load by skimming and vacuuming leaves by hand so the filter lasts longer between cleanings.

Seasonal patterns in Texas and Florida

  • Spring pollen and oak season (Central and North Texas, North Florida): expect more frequent cleaning.
  • Summer storms and heavy swim loads: more debris, sunscreen and body oils.
  • After a hurricane or a hail storm: clear debris by hand first, then clean the filter, possibly more than once.
  • After treating algae: dead algae clogs filters quickly; clean or backwash as soon as pressure climbs.

Deep cleaning

Hosing does not remove oils, sunscreen and scale. Many owners soak cartridges or DE grids in a filter cleaner or degreaser once or twice a year, following the product label. If you use acid to remove scale, degrease first and follow chemical safety rules. See pool chemical safety.

Step by step: cleaning each filter type

Backwashing a sand or glass filter

  1. Turn off the pump.
  2. Roll out the backwash hose to an approved discharge spot, if your system uses one.
  3. Set the multiport valve to Backwash. Never move the valve while the pump runs.
  4. Turn on the pump and run until the sight glass or hose water runs clear, often a couple of minutes.
  5. Turn off the pump, set the valve to Rinse, and run briefly to settle the media.
  6. Turn off the pump, set the valve back to Filter, and restart. Note the new clean pressure.
  7. Top off the pool if allowed under local watering rules.

Cleaning a cartridge filter

  1. Turn off the pump and open the air relief valve to release pressure.
  2. Open the drain plug if your model has one, then remove the clamp and lid.
  3. Pull out the cartridge and hose it from top to bottom, working between pleats. Avoid a pressure washer, which can damage the fabric.
  4. Inspect for tears, flattened pleats and cracked end caps.
  5. Check and lubricate the lid O-ring with a lubricant the maker approves.
  6. Reassemble, close the drain, restart and bleed air until water comes from the relief valve.

Backwashing and recharging a DE filter

  1. Backwash as for sand, following the manual (some DE filters use a push-pull valve).
  2. Capture spent DE if your system has a separation tank or bag.
  3. Restart on Filter, then add the amount of fresh DE the label specifies for your filter size, as a slurry through the skimmer, wearing dust protection.
  4. Record the new clean pressure. If it starts much higher than usual, the grids may need a full teardown and cleaning.

Once or twice a year, a DE filter needs a full teardown: remove the grid assembly, hose off all DE, inspect the fabric and soak in cleaner if needed.

How often should I replace cartridges, sand or DE grids?

MediaEPA typical lifeSigns it is time
Cartridge2 to 4 yearsFrayed or flattened pleats, cracked end caps, pressure that stays high after cleaning, cloudy water despite clean pressure
Sand3 to 6 yearsShort cycles between backwashes, sand clumped or channeled, sand returning to the pool (broken lateral)
DE grids2 to 3 yearsTorn fabric, DE blowing back into the pool, grids that stay caked
Glass7 to 15 yearsSimilar to sand

Heat, chlorine, heavy use and poor water balance shorten life. A pool that runs year-round in Florida may wear media faster than a seasonal pool in Dallas.

Changing sand means opening the tank, removing old sand (often with a shop vacuum), protecting the laterals, refilling with the type and amount on the filter label, and restarting with a rinse cycle. It is heavy, messy work. Florida law treats routine filter changes differently from other equipment work: the pool contractor definitions in s. 489.105 exclude "filter changes" from the cleaning and sanitizing that requires partial disassembly, so changing a filter element is not by itself licensed contracting. Replacing the filter tank or plumbing is equipment work for a licensed pool contractor.

Is DE filter powder safe?

DE is safe in the water but needs care when dry. EPA's WaterSense guide warns that DE can be harmful if inhaled. Check the product's safety data sheet for crystalline silica content. OSHA says breathing crystalline silica dust can cause silicosis (an incurable lung disease), lung cancer, chronic obstructive pulmonary disease and kidney disease. Read the safety data sheet for the specific product to see what it contains.

Safe handling:

  • Wear a properly fitted dust mask or respirator rated for fine dust, plus eye protection.
  • Mix DE into a slurry with water in a bucket before adding it to the skimmer, so it does not puff into the air.
  • Do not pour dry DE in the wind or near children or pets.
  • Store it sealed and dry.
  • Do not use garden or food-grade DE as a substitute unless the filter maker allows it; products differ.

Disposal: DE should not be dumped into storm drains, sewers or septic systems. Many filters use a separation tank or bag to catch spent DE during backwash. Ask your city or county how to dispose of it. Florida public pool rules require DE filter elements to be maintained with at least 1 inch of clear spacing and require the system to keep elements submerged when only the main drain is open (64E-9.008).

Can I backwash into the street or yard?

Not always. Backwash water carries dirt, chlorine or salt, and possibly DE. Rules vary by city, county and utility.

  • Florida plumbing rule: the Florida Building Code, Residential defines filter waste discharge piping as piping that carries filter waste to a drainage system through an air gap or other approved method, and it bars direct or indirect connections between storm drains, sewers, drainage systems, seepage pits or subsoil drains and any pool line unless the authority approves. Where pool waste goes to a public sewer, a 3-inch P-trap arrangement is required.
  • Storm drains: many cities restrict pool and backwash discharges to the street because storm drains flow to creeks, lakes and bays. We could not confirm current written backwash rules for Houston, Dallas, San Antonio, Austin, Miami-Dade, Tampa, Orlando or Jacksonville from official pages, so call your city's stormwater office before routing a backwash hose to the curb.
  • Lawns and gardens: EPA's WaterSense guide suggests using backwash water on lawns or gardens, as long as it is not freshly chlorinated. Salt-pool backwash can harm plants; see our saltwater pool guide.
  • Septic systems: do not send backwash into a septic tank or onto the drain field. Ask your county health department.
  • Neighbors: do not let backwash flow onto a neighbor's property.

Do cartridge filters save water in a drought?

Yes. EPA calls cartridge filters the most water-efficient choice because they do not require backwashing, and recommends them for new pools as a way to jump-start water efficiency. It also cites a California Urban Water Conservation Council estimate that 23% of quantifiable pool water use comes from filter backwashes.

That matters in Texas. Retail public water utilities with more than 3,300 connections must keep drought contingency plans, and each utility sets its own triggers and rules. Austin's plan suspends approval of new single-family pool and spa permits in Drought Response Stage 4 and Emergency Stage 5, and in Stage 5 no one may use water to fill, clean, rinse, supplement or maintain a pool. San Antonio Water System triggers its stages by Edwards Aquifer levels and prohibits water waste at all times. A sand filter that needs a big refill after each backwash can be a problem when top-offs are restricted.

Ways to cut backwash water with any filter:

  • Backwash only when pressure rises about 10 psi, as EPA suggests.
  • Skim and vacuum by hand to keep debris out of the filter.
  • Use a larger filter so it runs longer between cleanings.
  • Consider glass media in a sand filter for shorter backwash cycles.
  • Use a pool cover, which DOE says cuts make-up water needs by 30% to 50%.

See drought restrictions on filling pools.

Texas vs Florida: filter issues to plan for

IssueTexasFlorida
Water limitsCity drought plans (Austin, San Antonio) can restrict refills after backwashUtility and water management district rules; ask before discharging
DebrisOak pollen and tassels, cedar season, dust storms, hailYear-round leaf and pollen loads; hurricane debris; screened pools see less
DischargeCity stormwater rules; septic in rural areasFBC bars pool line connections to storm drains or sewers without approval; septic common in many counties
Run seasonYear-round in Houston and San Antonio, shorter in DallasYear-round in most of the state, so media wears faster
Code for new filtersCity-adopted ISPSC versionsFBC Residential R4501.20 (12-hour turnover, DE 2 gpm per sq ft)
Who replaces the tankNo state pool license; local rules; TDLR for electricalLicensed pool/spa contractor (CP or RP)

What size filter do I need?

Filters are rated by surface area (square feet) and maximum flow (gallons per minute). The filter must handle your pump's highest flow, and bigger is better within reason.

Step 1: Find your required flow

Florida's residential code requires filtration components that can turn over the pool in 12 hours or less (R4501.20). Flow (gpm) = pool gallons / (turnover hours x 60). A 20,000-gallon pool on a 10-hour turnover needs about 33 gpm. Spa jets, waterfalls and solar panels may need more flow at times.

Step 2: Apply a filtration rate

Each media type has a maximum rate in gpm per square foot. Florida's public pool rule gives conservative limits, which show the big differences between types:

MediaFlorida public pool max rate (64E-9.008)Area needed for 33 gpm at that rate
High-rate sand15 gpm/sq ft (20 if approved)2.2 sq ft
Rapid sand3 gpm/sq ft11 sq ft
Pleated cartridge0.375 gpm/sq ft88 sq ft
DE2 gpm/sq ft16.5 sq ft

Residential filters are often rated at higher flows per square foot by their makers. Florida's residential code caps DE filters at 2 gpm per square foot and treats sand filters above 5 gpm per square foot as "high rate" filters that must be an approved type. Use the manufacturer's rating and the code that applies to your pool.

Step 3: Oversize for savings

DOE recommends a large filter rated at least 50% higher than the pool's design flow rate, because it lowers resistance and lets you use a smaller pump. Lower resistance can cut pump electricity use by up to 40%, DOE says. A larger cartridge also means fewer cleanings.

For public pools in Florida, cartridges must be permanently marked with the maker's name, pore size and square feet of filter material on an end cap (64E-9.008), and filters must be NSF/ANSI 50 tested and approved.

Pool filter myths

  • "Backwash every week no matter what." EPA and DOE both point to pressure as the trigger. DOE says backwashing too often wastes water, while waiting too long makes the pump work harder, so let the gauge tell you when.
  • "A filter cleans the water by itself." Filters remove particles. Sanitizer kills germs and algae, and balanced chemistry keeps water clear. DOE notes chemicals and brushing are the best defense against algae.
  • "Finer is always better." DE filters the finest, but a well-sized cartridge or sand filter with good chemistry keeps most home pools clear. Choose based on water, work and budget.
  • "Running the pump faster filters better." Pushing water too fast through media can lower filter performance and raise pressure. Slower flow through a larger filter is often better and cheaper.

Can I switch from sand to cartridge (or DE)?

Usually, yes. EPA notes that changing filter types may require plumbing changes to run efficiently, so get a quote that covers:

  • The new filter tank and its valve (cartridge filters typically use a simple on-off flow path with no multiport valve)
  • Re-plumbing to fit the new tank's inlet and outlet
  • Removing or capping the backwash line if it is no longer needed
  • Checking pump flow and pressure with the new filter
  • Permits, if your city requires them

Fixr's January 2025 guide puts pool filter installation at $500 to $2,000 on average, with most owners spending about $1,000 for a cartridge or sand unit in a mid-sized in-ground pool, and up to $4,500 for a DE filter and pump on a 40,000-gallon pool. Above-ground filter systems run $250 to $1,100.

Who can do it: in Florida, replacing a filter tank and its piping is pool equipment work for a licensed pool/spa contractor (s. 489.105). In Texas, there is no state pool license; ask about local registration and get any electrical work done by a TDLR-licensed electrician.

Filters for HOA, condo and public pools

Community pools have stricter filter rules. In Florida, rule 64E-9.008 requires public pool filters to be sized for the required recirculation flow and kept performing as installed under the manufacturer's specifications. Flow rates may not be reduced after the operating permit is issued without DOH approval. Pressure filters need working air relief valves, influent and effluent gauges, and a sight glass where a backwash line is required; vacuum filters need a working vacuum gauge. Cartridges must carry permanent markings, and filters must be NSF/ANSI 50 approved. Public pools must also keep at least four turnovers a day.

Texas public pools follow DSHS rules in 25 TAC chapter 265 and the adopted ISPSC for construction, and must meet water clarity rules (an 8-inch black or Secchi disk visible at the deepest point) and keep test logs at least 3 years. Boards should keep filter maintenance records with their pool logs. See HOA, condo and apartment pool management.

Filters after storms, floods and freezes

  • After a hurricane or flood: remove large debris by hand, clean skimmer and pump baskets, and expect to clean or backwash the filter several times. Floodwater can carry silt that clogs cartridges and DE grids fast. Have an electrician check flooded equipment before restarting.
  • After hail (Texas): hail can shred leaves and break up debris that loads filters quickly. Check the filter lid and gauge for cracks.
  • Before a hard freeze (Texas, North Florida): a filter tank full of still water can crack. Keep the pump running with freeze protection, or ask a pro how to drain the filter if a long outage is expected. Open the air relief valve and drain plug when draining.

See hurricane prep and hail and freeze damage.

Why is my pool cloudy even with the filter running?

A filter can only clean water that passes through it, and it cannot fix chemistry. Work through these causes in order:

  1. Not enough run time or flow. If the pump runs too few hours or too slowly, water does not turn over. Florida's code uses 12 hours as the maximum turnover for new pools.
  2. Low chlorine. Bacteria and early algae make water hazy. Test free chlorine and shock if needed.
  3. pH or calcium out of balance. High pH and high calcium can make water milky as calcium falls out of solution.
  4. Dirty or worn media. Clean the filter; if pressure stays high or low, inspect for clogged or torn media.
  5. Filter bypass. A broken lateral, torn grid, cracked cartridge or bad O-ring lets dirty water slip past.
  6. Fine particles too small for the media. Sand at 20 to 40 microns may pass fine dust; a clarifier or upgrading to glass, cartridge or DE can help.
  7. Dead algae after treatment. Keep cleaning the filter until it clears.
  8. Poor circulation. Aim return jets to move water around the pool, and brush dead spots.

For public pools in Florida, water must be clear enough to see the main drain grate from the deck, with turbidity at or below 0.5 NTU (64E-9.004). Texas public pools must be clear enough to see an 8-inch black or Secchi disk at the deepest point (25 TAC 265.193). See green and cloudy pool fixes.

How to choose a provider

  • Write your filter's clean pressure reading on the tank.
  • Clean or backwash when pressure rises about 10 psi (EPA guidance) or as your manual says.
  • Always turn off the pump and open the air relief valve before opening the filter.
  • Skim and vacuum leaves by hand to reduce filter load.
  • Degrease cartridges or DE grids once or twice a year per product label.
  • Wear a dust mask and eye protection when handling dry DE; mix it into a slurry.
  • Replace cartridges, sand or grids when signs of wear show (EPA: 2 to 6 years for most media).
  • Ask your city before backwashing to the street; never into septic systems.
  • Size a new filter at least 50% above design flow, as DOE suggests.
  • Consider a cartridge filter or glass media to save water in drought-prone areas.
  • Use a licensed pool contractor in Florida for filter tank and piping replacement.
  • Compare filter pressure readings at the same pump speed every time.
  • After storms, floods or algae treatment, clean the filter again as soon as pressure climbs.
  • Keep a log of cleaning dates, pressures and media changes with your pool records.

Related swimming pool builders and contractors guides

Swimming pool builders and contractors by state and city

Questions people ask

Can a filter be too big for my pool?

Not in a harmful way for most residential pools. A larger filter lowers flow resistance, runs longer between cleanings and can let you use a smaller pump. DOE recommends a filter rated at least 50% above the design flow. The limits are cost, pad space and, for sand, making sure the pump can deliver enough backwash flow, which Florida's code sets at 12 to 15 gpm per square foot.

How do I know what kind of filter I have?

Look for a label on the tank. A sand or glass filter usually has a multiport valve on top or side with settings like Filter, Backwash and Rinse. A cartridge filter usually has a large lid with a clamp band and no multiport valve. A DE filter often has a push-pull or multiport valve and a label calling for DE or filter aid.

Should I add a filter clarifier?

A clarifier clumps tiny particles so the filter can catch them, which can help sand filters with fine haze. It does not fix low chlorine or unbalanced water. Follow the label dose, clean the filter afterward, and never mix clarifiers with other chemicals in a bucket.

Can I put DE in a sand or cartridge filter?

Some owners add a small amount of DE to a sand filter to improve fine filtering, but follow the filter maker's instructions first. Do not add DE to a cartridge filter unless the maker allows it, because it can clog the pleats. Always handle DE with dust protection.

Do robotic cleaners reduce filter work?

Yes, robotic cleaners have their own filter bags or canisters, so they catch dirt before it reaches the main filter. That can mean fewer backwashes or cartridge cleanings, which saves water with sand and DE filters. Empty and rinse the robot's filter after each run so it keeps its suction.

What filter do Florida public pools use?

Florida public pools can use high-rate sand, rapid sand, pleated cartridge or DE filters, each with a maximum filtration rate set in rule 64E-9.008. Filters must be NSF/ANSI 50 tested and approved, maintained to meet the operating permit's performance standards, and equipped with proper gauges and air relief valves.

Why does sand come back into my pool?

Sand in the pool usually means a broken lateral or standpipe inside the filter, or sand that is too fine for the filter. Turn off the pump, open the tank and inspect the laterals. Replace broken parts and refill with the sand type and amount listed on the filter label.

How much does a replacement cartridge or new sand cost?

Prices vary by size and brand. Fixr's January 2025 guide lists complete cartridge filter units at $200 to $1,600 and sand filter units at $300 to $1,200, but does not break out replacement media alone. Ask your pool supply store for the exact part number on your filter's label and compare prices before buying.

Is a variable-speed pump harder on my filter?

No. A variable-speed pump running at low speed sends water through the filter more gently, which often improves filtration and lowers pressure. Just compare pressure readings at the same speed each time, and make sure the pump delivers enough flow for a proper sand or DE backwash.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration