Local Guide · Electricians
Getting Shocked or Tingled at Home: Causes, Dangers and Fixes
A zap from a doorknob in winter is static. A tingle from a faucet, shower, appliance or pool is not, and it can be the warning before a serious injury. Here is what causes it, what to do after a shock, and how to fix it.
Any tingle or shock from a faucet, shower, light switch, metal fixture, appliance, pool or dock means current is flowing where it should not, usually from a ground fault, a missing or broken ground, a bonding failure, or a neutral problem. Stop using that fixture or area, turn off the related breaker if you can safely, and call a licensed electrician. If a person was shocked, call 911: MedlinePlus advises calling for any electrical injury. Never touch someone still in contact with the source.
Key facts
- MedlinePlus (U.S. National Library of Medicine) says to call 911 or your local emergency number for any electrical injury.
- MedlinePlus says internal injuries from an electrical shock can be serious even when skin burns look minor.
- MedlinePlus advises not touching an injured person with bare hands while they are still in contact with the electrical source, and not approaching someone touching high-voltage lines within 20 feet until the power is off.
- CPSC recommends testing every GFCI once a month and says GFCIs can fail without showing signs of failure.
- CPSC says electrical products, even plastic or double-insulated ones, can leak current if wet, and that pool and spa equipment should plug only into working GFCI outlets.
- The NEC requires an equipotential bonding grid around permanent pools extending at least 3 feet from the pool edge, to reduce voltage differences (NC Office of State Fire Marshal interpretation of 680.26(B)(2)).
- Under the 2020 NEC, marina shore power receptacles need ground-fault protection not exceeding 30 mA, and marina feeders and branch circuits need protection set at not more than 100 mA (Miami-Dade 2020 NEC summary).
- Texas rules require utilities to investigate customer power quality complaints with monitoring instruments (16 TAC 25.51).
If someone has just been shocked
Follow MedlinePlus first-aid guidance from the U.S. National Library of Medicine:
- Do not touch the person if they may still be in contact with the source. You can become a second victim.
- Cut the power if you can do it safely. Unplug the cord, remove the fuse, or switch off the breaker. MedlinePlus notes that simply turning off an appliance may not stop the flow of electricity.
- If you cannot cut power, separate the person from the source with a dry, non-conducting object such as a wooden broom handle. Avoid anything wet or metal.
- Call 911. MedlinePlus says to call for any electrical injury.
- Check breathing and pulse. Start CPR if the person is unconscious and you cannot feel a pulse.
- Rinse burns with cool water until the pain eases. Do not use ice, butter, ointments or adhesive bandages, and do not pop blisters.
- Protect the spine. Do not move the head or neck if the person may have a spine injury, and do not move them at all after the power is off unless there is ongoing danger such as fire.
For power lines, MedlinePlus says not to approach someone touching high-voltage lines within 20 feet until the power is off. Call 911 and the utility.
When should I go to the ER after an electrical shock?
MedlinePlus's guidance is simple: call 911 for any electrical injury. Its reason is important. The amount of harm depends on the voltage, how long contact lasted, the path the current took through the body, and the person's health, and internal injuries can be serious even when burns look minor.
Symptoms MedlinePlus lists include changes in alertness, seizures, irregular heartbeat, breathing problems, chest or arm pain, broken bones, headache, numbness or tingling, muscle spasms, trouble swallowing, vision or hearing problems, and skin burns. Anyone with those symptoms needs emergency care now.
What about a quick zap from an outlet where the person feels fine? We are not doctors, and this is not medical advice. Because MedlinePlus advises calling for any electrical injury, the safest choice is to call 911 or seek medical evaluation, and to be especially careful with children, pregnant people, anyone with a heart condition, and anyone whose shock involved current across the chest (hand to hand, or hand to foot).
Static shock or electrical fault? How to tell
| Clue | Probably static | Probably an electrical fault |
|---|---|---|
| When it happens | Dry, cool days; after walking on carpet or getting out of a car | Any weather; often when touching water, metal fixtures or appliances |
| What it feels like | A single sharp snap with a visible or audible spark | A tingle, buzz or vibration that lasts as long as you touch it |
| Repeatability | Random; goes away after the first touch | Same spot every time, or every time an appliance runs |
| Where | Doorknobs, other people, car doors | Faucets, shower handles, switch plates, appliance cases, pool rails, dock ladders |
If it is a lasting tingle, it is not static. Treat it as a fault.
Why do I feel a tingle in the shower or at a faucet?
A tingle at plumbing is one of the most important warnings in a home, because wet skin conducts electricity far better than dry skin. Common causes:
- A ground fault in an appliance connected to plumbing, such as an electric water heater, a dishwasher, a disposal, a washing machine or a well pump. If an internal wire touches the metal case, the case and pipes can become energized.
- A missing or broken bonding connection. Metal water piping is bonded to the electrical grounding system so it stays at the same voltage as everything else. If a plumber replaced a section of metal pipe with plastic, or a bonding clamp corroded off, parts of the piping can sit at a different voltage.
- A neutral problem. If your service neutral is loose or broken, return current can look for other paths, including your water pipes. A tingle plus dim or bright lights is a strong sign. See lost neutral.
- Stray voltage from the utility system, where a small voltage appears between neutral and earth. This is less common and needs testing by the utility.
What to do
- Stop using the shower or faucet.
- Turn off the breaker for the water heater and any nearby appliance on plumbing, if you can do so from a dry floor.
- If lights are also behaving oddly, call the utility first.
- Call a licensed electrician to test bonding, grounding, and the appliances. A plumber may be needed if bonding was lost during plumbing work.
Why did I get shocked touching a light switch?
A shock from a switch usually means one of these:
- A cracked or broken switch or cover plate exposing a live part. CPSC says exposed wiring is a shock hazard and every outlet and switch should have a faceplate.
- A metal cover plate on a box with no ground, where a loose wire touches the plate or the box.
- A loose wire touching the metal mounting strap.
- Moisture from a leak in the wall or ceiling.
Turn off the breaker and do not use the switch until it is repaired. If the switch is warm, buzzing or smells, see burning smells.
Why does my metal fixture or appliance shock me?
Appliances with metal cases, such as dryers, washers, ranges, refrigerators and older lamps, are designed so that if a live wire touches the case, current flows down the ground wire and trips the breaker. A shock means that path is missing or broken. Common reasons:
- The appliance is plugged into a two-prong outlet with a cheater adapter whose ground tab is not connected. CPSC says to always connect the adapter's grounding wire or tab to a grounded screw and to never defeat the adapter's grounding feature or break the ground pin off a plug.
- The outlet looks grounded but is not, such as a three-prong outlet on a two-prong circuit or a "bootleg" ground jumper. See ungrounded outlets.
- A damaged power cord or plug.
- An internal appliance fault.
- Older dryer and range circuits that use three wires rather than four, where the neutral and ground are combined. If the neutral fails, the appliance case can become energized. Ask an electrician to evaluate older three-wire connections.
Is a small shock from an appliance dangerous?
Yes. The small shock is the warning. The same fault with wet hands, bare feet on a concrete floor, or a child's hand can be far worse. Unplug the appliance and stop using it until the appliance and the outlet are checked.
Ground faults, open grounds, bonding and neutral: what the terms mean
| Term | Plain meaning | Why it causes shocks |
|---|---|---|
| Ground fault | Current leaving its normal path and flowing to ground through something else, such as a metal case, water, or a person | If you become the path, you get shocked |
| Open ground | The ground wire is missing, loose or broken | A faulty appliance cannot trip the breaker, so the fault stays on the metal case |
| Bonding | Connecting metal parts together (pipes, pool rails, panels) so they stay at the same voltage | A broken bond lets two things you touch at once be at different voltages |
| Neutral-to-ground voltage | A voltage difference between the neutral system and earth | Small amounts can cause tingles at water or pools; a failing neutral can make it large |
| GFCI | A device that trips when it detects current leaking to ground | Prevents most shock injuries in wet areas when it works |
GFCIs: your best defense, if they work
A ground-fault circuit interrupter (GFCI) compares current going out and coming back. If some is missing, it may be flowing through a person, and the GFCI cuts power in a fraction of a second. The 2023 NEC requires listed Class A GFCIs, which trip at a nominal 5 milliamps, in the required locations.
CPSC recommends testing every GFCI once a month, because GFCIs can fail without showing signs of failure. To test: plug in a lamp and turn it on, press TEST (the lamp should go off), then press RESET. If the lamp stays on after TEST, replace the GFCI.
Where should you have GFCI protection? CPSC recommends GFCIs in kitchens, bathrooms, garages, unfinished basements, laundry areas, outdoors and near pools and spas. Under the 2020 NEC (Florida's current code) and later editions, required dwelling locations expanded, including all basement receptacles and indoor damp and wet locations. Older homes may have far fewer. Adding GFCI protection is one of the most cost-effective safety upgrades. See GFCI and AFCI requirements.
Why do I get shocked in the pool or hot tub?
A tingle in a pool or spa is a stop-everything moment. Get everyone out of the water without touching metal rails or ladders if possible, and turn off the pool and spa equipment at the breaker.
Likely causes:
- A failed bond on pool equipment, rails, ladders, lights or the pool shell.
- A missing or damaged equipotential bonding grid. Since the 2008 NEC, permanent pools, in-ground or aboveground, need a bonding grid under the walking surface extending at least 3 feet from the pool edge, whether or not the deck is paved. The North Carolina Office of State Fire Marshal explains that the purpose is to eliminate differences in voltage between metal parts and surrounding surfaces. Deck replacements and remodels sometimes break it.
- A faulty pool light, pump motor or heater.
- A neutral or utility issue that raises the voltage of the bonded system compared with earth.
- Plug-in equipment such as pumps, vacuums, radios or speakers. CPSC says even plastic or double-insulated products can leak current when wet, and to plug pool and spa equipment only into working GFCI outlets.
Call a licensed electrician who does pool work. In Texas, TDLR's residential appliance installer license covers residential pool-related electrical installation and maintenance for an appliance installation contractor; general electricians also do pool work. In Florida, a licensed electrical contractor does it. See pool and spa bonding.
What is electric shock drowning?
Electric shock drowning is the term safety groups use when a swimmer is exposed to electric current in the water, often from faulty wiring on a dock, boat or pool, and the current causes muscle paralysis so the person cannot swim and drowns. It is a particular concern in Florida, with its many docks, marinas, canals and pools, and on Texas lakes and the Gulf Coast.
We could not load the Electrical Safety Foundation International (ESFI) page on this topic to verify its statistics, so we do not quote any. What the code says is concrete: the 2020 NEC requires shore power receptacles at marinas to have ground-fault protection not exceeding 30 milliamps, and marina feeders and branch circuits to have ground-fault protection set to open at not more than 100 milliamps.
Practical rules near docks and pools
- Do not swim near docks, marinas or boats with shore power connected.
- If a swimmer says they feel tingling, tell them to move away from the dock or boat, not toward it.
- Do not jump in to rescue someone you think is being shocked. Follow MedlinePlus's rule: cut the power first. Shut off the dock or pool power, then reach or throw a flotation device.
- Have dock and pool wiring inspected and test GFCIs on docks and lifts monthly.
See boat dock and marina electrical.
Stray voltage and the utility
Sometimes the source is outside the house. A broken neutral on the utility's service drop or transformer can raise the voltage on your grounding and bonding system. Symptoms often include tingles at water or pools plus lights that dim on one side and brighten on the other.
Texas power quality rules (16 TAC 25.51) require utilities to provide and use monitoring instruments to investigate customer power quality complaints. In San Antonio, CPS Energy takes power quality investigation requests at 210-353-2222. In deregulated Texas, call the delivery company (such as Oncor at 888-313-4747 for outages and emergencies), not your retail provider. In Florida, call your utility: FPL, Duke, TECO, JEA, a city utility or co-op.
Tell them you are getting shocks or tingles and ask for a neutral and voltage check at the service. If the utility finds its side is fine, a licensed electrician should test your service grounding, bonding and neutral connections.
Who is liable if a tenant gets shocked?
This is general information, not legal advice. Talk to a Texas or Florida attorney about a specific injury.
- Texas: A landlord must make a diligent effort to repair conditions that materially affect the physical health or safety of an ordinary tenant after the tenant gives notice and is current on rent (Tex. Prop. Code 92.052). Seven days is presumed a reasonable time to repair (92.056(d)). The landlord does not have to repair conditions the tenant or guests caused, other than normal wear and tear.
- Florida: A landlord must comply with applicable building, housing and health codes (s. 83.51(1)(a)). If the landlord materially fails to comply within 7 days after written notice, the tenant may have the right to terminate the lease (s. 83.56(1)).
Tenants: stop using the fixture or appliance, give written notice, and keep copies and photos. If a person was hurt, get medical care first. Landlords: treat a shock report as an emergency, shut off the affected circuit and send a licensed electrician. See landlord and tenant electrical.
How to choose a provider
- If a person is in contact with the source, cut the power before touching them.
- Call 911 for any electrical injury, as MedlinePlus advises.
- Stop using any faucet, shower, switch, appliance or pool that tingles.
- Turn off the related breaker if you can do it from a dry floor.
- Unplug appliances on cheater adapters and never break off a ground pin.
- Test every GFCI monthly; replace any that do not trip.
- Call the utility if tingles come with dim or bright lights.
- Have a licensed electrician check grounding, bonding and neutral connections.
- Do not swim near docks or boats with shore power; never jump in to rescue a shocked swimmer.
- Renters: give written notice and keep copies.
Related electricians guides
- What electrical work does a pool or hot tub need to be safe?
- How do you keep boat dock wiring safe from electric shock drowning?
- GFCI and AFCI Requirements: Where Are They Required in Texas and Florida Homes, and Why Do They Trip?
- Two-Prong Ungrounded Outlets: Are They Legal, Are They Safe, and What Are the Real Fixes?
- Why Is the Power Out in Half My House (and What Do I Do)?
- What Are Landlord and Tenant Electrical Rights in Texas and Florida? Repairs, Shutoffs and Outages
- What Counts as an Electrical Emergency? When to Call 911, the Utility or an Electrician
Electricians by state and city
Questions people ask
What should I do after an electric shock?
Make sure the person is no longer touching the source, cutting power first if needed. Call 911: MedlinePlus advises calling for any electrical injury, because internal injuries can be serious even when burns look small. Check breathing and pulse and start CPR if needed. Rinse burns with cool water. Then turn off the circuit involved and have a licensed electrician find the fault before anyone uses it again.
Is a small shock from an appliance dangerous?
Yes. A small shock means current is reaching the case, usually because the ground path is missing or the appliance has an internal fault. With wet hands or bare feet on concrete, the same fault can be far more dangerous, and children are more vulnerable. Unplug the appliance, stop using it, and have the appliance and outlet checked.
Why do I feel a tingle in the shower?
Something is putting voltage on the plumbing or the water. Common causes are a faulty water heater or appliance on the plumbing, a broken bonding connection on the pipes, or a neutral problem at the service. Stop using the shower, turn off the water heater breaker if you can do it safely, and call an electrician. If lights are also dimming and brightening, call the utility first.
Can static shock be confused with an electrical fault?
Static is a single sharp snap, often with a spark, on dry days after walking on carpet, and it does not repeat when you touch the same thing again. An electrical fault feels like a tingle or buzz that lasts as long as you touch, happens at the same place each time, and often involves water, metal fixtures or appliances. If it repeats, treat it as a fault.
What is electric shock drowning?
It is drowning caused when electric current in the water, often from faulty dock, boat or pool wiring, paralyzes a swimmer's muscles. Do not swim near docks or boats with shore power. If a swimmer feels tingling, they should move away from the dock. Never jump in to help; cut the power first, then use a flotation device. The NEC requires ground-fault protection on marina shore power.
Why do I get shocked touching my dryer or washer?
Usually the appliance's ground path is missing or broken: a two-prong outlet with an adapter, a damaged cord, a miswired outlet, or an older three-wire dryer or range connection with a neutral problem. It can also be an internal fault. Unplug or switch off the appliance, do not use it, and have an electrician check the outlet and connection and an appliance technician check the machine.
Sources
- MedlinePlus: Electrical injury
- CPSC Home Electrical Safety Checklist, Pub. 513 (July 2008)
- Mike Holt: 2023 NEC changes, 210.8 GFCI
- Miami-Dade: Electrical Changes for the 2020 NEC
- NC Office of State Fire Marshal: 680.26(B) Swimming Pool Equipotential Bonding Grid
- 16 Tex. Admin. Code 25.51, Power Quality
- CPS Energy: Power Quality FAQs
- Oncor: Outage FAQs
- TDLR: Residential Appliance Installer license
- Texas Property Code ch. 92
- Florida Statutes s. 83.51
- Florida Statutes s. 83.56
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


