New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Electricians

What electrical work does a pool or hot tub need to be safe?

A plain-English guide to NEC Article 680 for Texas and Florida pool and spa owners: equipotential bonding, GFCI protection, outlet and light distances, overhead line clearances, pool lights, permits, who is licensed to do the work, and what to do if you feel a tingle in the water.

A pool or hot tub needs two separate protections. Equipotential bonding ties every metal part, the pool shell steel, the deck and the water into one connected system so there is no voltage difference to shock a swimmer. GFCI protection shuts off power when current leaks. The rules are in NEC Article 680. Texas enforces the 2026 NEC and Florida the 2020 NEC until its 9th Edition code takes effect. Use a licensed electrician and get the work permitted and inspected.

Key facts

  • Equipotential bonding under NEC 680.26 connects metal pool parts, reinforcing steel, the deck and the pool water so they stay at the same voltage (IAEI, 2017).
  • Since the 2008 NEC, a bonding grid must extend at least 3 feet out under the walking surface around a permanent pool, paved or not (NC Office of State Fire Marshal interpretation).
  • The pool water itself must be bonded with at least 9 square inches of conductive surface in contact with the water (IAEI, 2017).
  • Receptacles must be at least 6 feet from the inside walls of a pool, and receptacles within 20 feet must be GFCI protected (IAEI, 2015; IAEI, 2025 for the 250-volt scope).
  • Insulated overhead cables up to 750 volts need at least 22.5 feet of clearance above a pool's maximum water level under the NEC table discussed by IAEI.
  • Underwater pool lights must be installed 4 to 18 inches below the normal water level (IAEI, 2025, citing NEC 680.23).
  • Low-voltage landscape lights must generally stay at least 10 feet from pools, spas and fountains unless Article 680 allows otherwise (UL, via IAEI).
  • Florida's Residential Swimming Pool Safety Act requires new residential pools to have at least one listed safety feature to pass final inspection (s. 515.27, F.S.).
  • Texas lets a licensed residential appliance installer connect a pool-related electrical device to an existing circuit; new circuits need a licensed electrician (Occ. Code 1305.002).

Why is pool and spa wiring held to stricter rules?

Water lowers the body's resistance to current, and a swimmer is surrounded by it. A small leak of current that you would never feel on dry ground can be dangerous in a pool. An IAEI article on electric shock drowning notes that as little as 10 milliamps (mA) through the body can cause loss of muscle control, which can lead to drowning.

The National Electrical Code (NEC, also called NFPA 70) handles this with a whole article, Article 680, titled Swimming Pools, Fountains, and Similar Installations. It covers in-ground and aboveground pools, hot tubs and spas, storable pools, fountains and hydromassage tubs. The goal, as IAEI describes it, is to keep people and electricity apart by distance, by isolation and by fast-acting protection.

Which code edition applies in Texas and Florida?

StateElectrical code in forceWhat to know
Texas2026 NEC, statewide since September 1, 2026 (16 TAC 73.100)Cities may amend locally. A pool permitted before that date may have been reviewed under the 2023 NEC.
Florida2020 NEC through the 8th Edition (2023) Florida Building CodeThe 9th Edition (2026) FBC, based on the 2023 NEC, takes effect December 31, 2026 per the Florida Building Commission. Tampa has announced January 1, 2027. The edition is generally set by the date your permit application is accepted.

Section numbers shift between editions. For example, the overhead clearance table was 680.8 in older editions and is 680.9 in newer ones. When you talk to an inspector, ask which edition your permit is under. See our guide to NEC adoption in Texas and Florida.

What is pool bonding, and how is it different from grounding?

People mix these up, and the difference matters.

  • Bonding means connecting metal parts together so they are always at the same voltage. If everything a swimmer can touch is at the same voltage, current has no reason to flow through the swimmer.
  • Grounding means giving fault current a low-resistance path back to the electrical source so a breaker or fuse trips. That path is the equipment grounding conductor, the green or bare wire run with the circuit.

IAEI sums it up: bonding means connected together, grounding means connected to earth. A pool needs both. A pump with a perfect ground wire can still leave a voltage difference between the water and the deck if the bonding is missing or broken.

What equipotential bonding (NEC 680.26) connects

IAEI's 2017 explainer of 680.26(B) lists the parts that must be bonded together:

  • The conductive pool shell, including reinforcing steel (rebar) in concrete, gunite or block pools. Normal steel tie wires are acceptable if tight. Vinyl liner and fiberglass shells are not conductive and are treated differently.
  • The perimeter surfaces (the deck), extending 3 feet beyond the inside walls of the pool, unless separated by a permanent wall or building at least 5 feet tall.
  • Metal forming shells of wet-niche lights and brackets of no-niche lights.
  • Metal fittings in or attached to the pool structure, except small isolated parts no larger than 4 inches that penetrate no more than 1 inch.
  • Metal parts of pump motors and circulation equipment, and pool cover motors.
  • Metal-sheathed cables, raceways, metal pipes and fixed metal parts within 5 feet horizontally of the inside walls and within 12 feet above the maximum water level, such as metal fences, railings and some door frames.
  • The pool water itself, through at least 9 square inches of bonded metal in contact with the water, such as a ladder, a light niche or a listed water bonding fitting.

The bonding conductor is solid copper, no smaller than 8 AWG, or approved corrosion-resistant metal conduit. It does not have to run back to the electrical panel. IAEI notes the NEC never intended the 8 AWG bonding conductor to be extended to a remote panelboard.

How is the bonding grid built under the pool and deck?

IAEI describes the equipotential bonding grid as two parts: the conductive pool shell (sometimes called belly steel) and the perimeter surface (deck steel).

The pool shell

In a concrete or gunite pool, the tied rebar usually serves as the shell bond. Where rebar is coated with an insulating compound at the factory, or where none is used, the code allows a copper grid instead: 8 AWG bare solid copper laid in a 12 inch by 12 inch pattern, with a 4 inch tolerance, bonded at every crossing and within 6 inches of the outer contour of the shell.

The deck

The perimeter grid runs under paved and unpaved walking surfaces for 3 feet out from the inside walls. Methods include the deck's rebar or wire mesh, or a copper conductor ring. Where the shell is conductive, the deck grid must be attached to the shell steel at a minimum of four points spaced evenly around the pool. The North Carolina fire marshal's 2008-code interpretation describes the single-conductor option: an 8 AWG bare copper conductor 18 to 24 inches from the pool edge. IAEI adds that it is secured 4 to 6 inches below the subgrade and can be spliced only with listed connectors.

Why this matters to owners

The grid is buried. Once concrete is poured, nobody can see it, which is why the bonding inspection happens before the deck is poured. If you are buying a home with a pool, ask the seller for the final electrical inspection record. If you are adding pavers or extending a deck, the new surface may fall within the 3 foot zone and need its own bonding, so involve an electrician before the contractor starts.

The pool is not a grounding electrode

A detached garage or pool house needs its own grounding electrode. Some installers used to connect that electrode wire to the pool steel. The 2017 NEC added 250.52(B)(3), which prohibits using a pool's structural steel as a grounding electrode, because it would invite fault current into the pool.

Does my pool pump need GFCI protection?

Yes, in current codes. IAEI's inspection article explains that pool pump motors of 120 through 240 volts on 15 or 20 amp branch circuits require GFCI protection, a rule added since the 2008 NEC. Check your edition for the full current scope. A ground-fault circuit interrupter (GFCI) compares the current leaving and returning on a circuit and trips when they differ by about 4 to 6 mA, which UL 943 sets as the range for personnel protection.

Double-insulated pump motors

Some pump motors are listed as double-insulated. IAEI notes that their accessible metal parts must not be bonded directly to the bonding grid. But the code still requires an 8 AWG solid copper bonding conductor to be brought to an accessible point near the motor, long enough to connect to a future replacement motor that is not double-insulated.

Variable-speed pumps

Many owners are replacing single-speed pumps with variable-speed models for energy savings. From an electrical standpoint, a variable-speed pump is still a pool motor under Article 680: it needs the right circuit, GFCI protection where required, and a bond connection. If a new pump trips its GFCI, have an electrician check the installation and the manufacturer's instructions rather than removing the protection. Federal efficiency rules for pool pumps exist, but they are efficiency rules, not wiring rules, and we did not confirm their current text for this guide.

How far must outlets, lights and switches be from a pool?

Distances are measured from the inside wall of the pool, horizontally, along the shortest path a cord would follow without going through a wall, door or window.

ItemRuleSource
General-purpose receptaclesAt least 6 feet from the inside walls of the poolNEC 680.22(A), as described by IAEI
Required receptacleAt least one receptacle near the pool, within 20 feet, for servicing and to discourage extension cordsNEC 680.22(A)
GFCI for receptaclesAll 125-volt through 250-volt receptacles within 20 feet of the pool walls must be GFCI protectedNEC 680.22(A)(4), per IAEI 2025
Lights within 5 feet of the poolAt least 12 feet above the maximum water levelNEC 680.22(B), per IAEI
Lights 5 to 10 feet from the poolAllowed with GFCI protectionNEC 680.22(B)(4), per IAEI
Low-voltage landscape lightsNot within 10 feet of pools, spas or fountains unless Article 680 permitsNEC 411.4, UL guidance via IAEI
Ceiling fans over a covered patio near the poolSame height and protection zones as lightsNEC 680.22(B)

Two common mistakes: plug-in landscape lights placed right at the pool edge, and a standard outdoor outlet within a few feet of the water that was added years after the pool passed inspection. UL's guidance is direct: listed low-voltage landscape luminaires are for installation not less than 10 feet from a pool, and a pool transformer must not be used to power landscape lights. GFCI protection on the primary side of a landscape transformer does not protect the low-voltage side.

Wondering about general outdoor outlet rules? See outdoor outlets and landscape lighting.

Can power lines run over a pool?

Not low. The NEC sets minimum clearances from the pool's maximum water level, meaning the level at which water would spill over the edge. IAEI's inspection article summarizes the table: insulated cables operating at up to 750 volts need at least 22.5 feet of clearance over the water, and communications lines need at least 10 feet. The table also covers diving structures and observation stands, which need clearance measured from their tops.

The reason is practical. Pool skimmer poles extend to 14 or 15 feet, and a 6-foot person can lift one to about 20 feet. Clearance keeps an aluminum pole from reaching the line.

If you are planning a pool and your service drop crosses the backyard, deal with it at the design stage. The utility may be able to reroute the drop or move it underground. A pool contractor who ignores this can end up with a finished pool that cannot pass inspection. The utility owns the service line but you own the attachment point on the house in most Texas and Florida utility areas, so expect your electrician and the utility to coordinate. See service drop responsibility.

Also check before digging. Underground utility lines and pool-related wiring have their own rules. The 2017 NEC removed the separate pool burial table and points to the general burial depths of Table 300.5, while still limiting what wiring can run under or near a pool.

What about pool lights, and why do they fail or leak?

Underwater lights are the most dangerous part of a pool's electrical system because they sit in the water. Article 680.23 covers them. IAEI's 2025 summary says underwater luminaires must be installed 4 to 18 inches below the normal water level, must be removable to the deck for servicing with enough cord, and connect through listed forming shells and junction boxes.

Low-voltage vs. line-voltage lights

  • Line-voltage (120-volt) lights require GFCI protection.
  • Low-voltage lights run from a listed pool transformer or power supply. Listed low-voltage systems with nonmetallic forming shells do not need the shell bonded.

Wet-niche fixtures

The most common pool light is a wet-niche fixture: the light sits in a forming shell (the niche) that fills with pool water. If the conduit to the niche is PVC, IAEI explains that an 8 AWG bonding jumper must run inside it, terminate in the shell, and be covered with encapsulating compound to protect it from corrosion. The conduit then runs to a listed junction box or enclosure that meets 680.24.

Common failure signs

  • Water inside the lens, fogging or a flooded fixture
  • A pool light circuit that trips its GFCI
  • A cracked or loose cord at the niche
  • Corrosion at the junction box

Do not swim while a light is being repaired, and never reach into a niche with the circuit on. An electric shock drowning incident list cited by IAEI includes a 2019 death in a home pool where a child grabbed a wire to an underwater light under repair, and a 2020 death in a Harris County, Texas, hotel pool with exposed light fixture wiring.

Why do I feel a tingle in my pool, and what should I do?

A tingle means current is flowing through your body. Treat it as an emergency.

  1. Get everyone out of the water, calmly, without touching ladders, rails or other metal if possible.
  2. Do not jump in to help someone who is frozen or struggling. Rescuers become victims in electric shock drowning. Use a non-metal pole or flotation device, and shut the power off first.
  3. Turn off every breaker for the pool: pump, lights, heater, chlorinator and nearby outlets. If you are not sure which ones, turn off the main.
  4. Call 911 if anyone was hurt or is unresponsive.
  5. Keep the pool closed until a licensed electrician finds and fixes the cause.

Common causes

  • A broken or corroded bonding connection, often at the pump, heater, light niche or a metal rail
  • A failing pump motor or pool light with leakage current
  • New deck work, pavers or a fence added without bonding
  • A neighboring electrical fault or a utility neutral problem bringing voltage into the ground near the pool
  • An extension cord or appliance near the water

An electrician can test continuity between bonded parts, measure voltage between the water and nearby surfaces, and check each circuit's GFCI. If the source appears to be outside your property, call your utility as well. For general shock symptoms anywhere in the house, see electrical shocks and tingles.

How do salt systems and the Florida climate affect pool wiring?

Florida has heavy pool use, a salty coastal atmosphere and many saltwater chlorine generator systems. Salt is the enemy of electrical connections. NEMA's 2026 guide on water-damaged equipment notes that salt water is particularly damaging because its residue is corrosive and conductive. For a pool, that means bonding lugs, clamps and equipment terminals can corrode faster than you would expect.

Practical steps for owners in Miami, Tampa, Jacksonville and other coastal areas:

  • Look at the bonding lugs on the pump, heater and salt cell housing every few months. Green or white crust, loose clamps or broken strands need an electrician's attention.
  • Keep equipment pads clear of standing water and pool chemicals, and store chemicals away from electrical equipment.
  • Replace corroded junction box covers and fittings with listed corrosion-resistant parts.
  • After a hurricane or flood, do not re-energize pool equipment that was underwater until it is evaluated. NEMA says GFCIs, AFCIs and wiring devices exposed to water should be replaced, not reconditioned. See flood-damaged electrical.

Texas pools face different stresses: extreme heat on equipment pads, shifting clay soils that can strain buried conduit and bonding connections, and Gulf Coast humidity and salt air near the coast. The inspection advice is the same.

Do hot tubs and spas need a disconnect, and can I install one myself?

Spas and hot tubs are covered by Article 680, Part IV, in addition to the general rules. Florida's pool safety law defines a portable spa as one whose controls and heating and circulation equipment are built in and that is cord-connected, not permanently wired (s. 515.25, F.S.).

Plug-in vs. hard-wired

  • Cord-and-plug spas (often 120-volt units) plug into a GFCI-protected receptacle located at least 6 feet from the water under the receptacle rules above.
  • Hard-wired spas (usually 240-volt) need a dedicated circuit sized from the nameplate and installation instructions. NEC 110.3(B) requires listed equipment to be installed according to its instructions, which usually specify the GFCI and disconnect arrangement.

The disconnect question

Article 680 requires a maintenance disconnecting means for pool and spa equipment so it can be shut off for service. Many guides repeat a rule that a spa disconnect must be within sight of the tub and at least 5 feet from the water. We could not load the current NEC text to confirm the exact wording and distance for each edition, so treat that figure as something to confirm with your inspector or the spa's installation manual.

Doing it yourself

Texas: the state licensing law does not apply to work on a dwelling by the owner who lives there, unless a city ordinance regulates it (Occ. Code 1305.003(a)(6)). City ordinances can still require permits or restrict homeowner electrical work, so call your city building department first.

Florida: an owner may pull a permit and do electrical work on a single-family or duplex home they will occupy, under the owner-builder exemption in s. 489.503(6), F.S., after signing the required disclosure. The work must still pass inspection.

Bonding and GFCI mistakes are not forgiving. For a 240-volt spa, hiring a licensed electrician is the safer choice. See what electrical work you can do yourself.

Who is licensed to wire a pool in Texas and Florida?

Texas

Texas licenses electrical work through TDLR under Occupations Code chapter 1305. The law creates a specific path for pool equipment: a residential appliance installer working for a licensed residential appliance installation contractor may do pool-related electrical maintenance, which the statute defines as connecting or disconnecting a pool-related electrical device to an existing circuit. A pool-related electrical device is equipment installed as a unit, directly connected to a circuit, performing a specific function, and using single-phase power of 240 volts or less. New circuits, feeders, subpanels and bonding grids are electrical work for a licensed electrician working for a licensed electrical contractor. Check any license at TDLR's license search. See Texas electrician licensing.

Florida

Florida licenses pool contractors under s. 489.105, F.S. The commercial and residential pool/spa contractor definitions cover construction, repair and servicing of pools and spas, equipment installation, heaters, piping and equipment rooms. They do not list electrical power wiring. Electrical contracting is licensed separately by the Electrical Contractors' Licensing Board under Part II of chapter 489. In practice, the pool contractor builds the pool and places the equipment, and a licensed electrical contractor runs the circuits, sets the panel or disconnect and makes or verifies the bonding connections. Your county or city building department decides which permits each trade pulls. See Florida electrician licensing.

Does a pool need a permit and an electrical inspection?

Expect a new pool or spa with hard-wired equipment to need building and electrical permits; confirm with your city or county. Typical inspection stages for an in-ground pool:

  1. Pre-pour or steel inspection: rebar, shell bonding, light niches and the deck bonding grid are checked before gunite or concrete covers them.
  2. Deck bonding inspection: before the deck is poured or pavers are set.
  3. Rough electrical: conduit, feeders and junction boxes.
  4. Final electrical: GFCI protection, receptacles, lights, disconnects, labeling and the bonding connection to equipment.
  5. Barrier and safety feature final: in Florida, a new residential pool must have at least one of the safety features in s. 515.27: an enclosure meeting the barrier rules, an approved safety cover, exit alarms on doors and windows that open to the pool, self-closing and self-latching devices on those doors with release at least 54 inches high, or a certified swimming pool alarm. Wearable child alarms do not count. Barriers must be at least 4 feet high on the outside (s. 515.29).

Florida's barrier rules are safety rules, not electrical rules, but exit alarms and powered safety covers involve wiring, and they must work at final. Florida law defines a residential swimming pool as one holding water more than 24 inches deep, including hot tubs and non-portable spas (s. 515.25).

In Texas, permit and inspection steps are set by each city building department, in Houston, Dallas, San Antonio, Austin and elsewhere. Ask for the electrical inspection list when you apply. See Texas electrical permits and Florida electrical permits.

Who checks pool bonding in a home inspection, and what does repair involve?

A general home inspector looks at what is visible: the equipment pad, GFCI protection, outlet locations, light condition and bonding wires at the pump and heater. A home inspector cannot see the buried bonding grid or confirm it was ever installed. If the inspection notes missing or corroded bonding, ask a licensed electrician for a pool electrical evaluation.

What the evaluation can include

  • Visual check of every bonding connection at equipment, rails, ladders, light niches and nearby metal
  • Continuity testing between bonded parts
  • Voltage checks between the water and the deck and equipment
  • GFCI testing on every pool circuit
  • Review of permit and inspection history with the city or county

Repairs

Repairs range from replacing a corroded lug to adding a water bonding fitting, running a new 8 AWG conductor to equipment, or, where a deck was replaced without bonding, installing a perimeter copper ring under or around the new surface. Cost depends on access and how much concrete or paver work is involved. We did not find a dated, published cost study for pool bonding repair, so get at least two written quotes that describe the exact work and the permit.

In Florida, if a home needs a 4-point insurance inspection, the electrical section looks at the main panel and wiring, not pool bonding specifically, but visible hazards anywhere can be noted. See Florida 4-point inspection.

Pool electrical safety habits for every owner

  • Press the TEST button on every pool and spa GFCI monthly and after storms. If it does not trip and reset, call an electrician.
  • Keep radios, phones on chargers and extension cords away from the water. Use battery-powered devices near the pool.
  • Never swim during thunderstorms. The National Weather Service counts Florida among the states with the most lightning deaths.
  • Do not let anyone swim while a pool light or pump is being serviced.
  • Keep a simple pool electrical file: permits, final inspection records, equipment manuals and any repair invoices. It helps a buyer, an insurer or an electrician later.
  • After any deck, fence or patio project near the pool, ask whether new metal or new surfaces within 5 feet need bonding.

How to choose a provider

  • Confirm which NEC edition your pool permit falls under (2026 NEC in Texas; 2020 NEC in Florida until the 9th Edition FBC applies).
  • Ask for the steel and deck bonding inspection records before any concrete is poured.
  • Keep general receptacles at least 6 feet from the water and GFCI-protect every receptacle within 20 feet.
  • Keep low-voltage landscape lights at least 10 feet from the pool unless Article 680 allows otherwise.
  • Check overhead line clearance before you design a new pool.
  • Test every pool and spa GFCI monthly.
  • Inspect bonding lugs at the pump, heater and salt cell for corrosion, especially near the coast.
  • If anyone feels a tingle, clear the pool, shut off pool breakers and call an electrician.
  • Hire a licensed electrician for new circuits and bonding; verify the license with TDLR or DBPR.
  • In Florida, make sure a listed safety feature is in place for the final inspection (s. 515.27).
  • Keep a pool electrical file of permits, inspections and repairs.

Related electricians guides

Electricians by state and city

Questions people ask

What is equipotential bonding in a pool?

Equipotential bonding, required by NEC 680.26, connects the pool shell steel, the deck within 3 feet, metal fittings, light niches, pump motors, nearby fixed metal and the pool water into one system with 8 AWG solid copper or approved methods. Because all of those parts stay at the same voltage, current has no path through a swimmer who touches two of them. It is separate from grounding, which helps breakers trip.

Is GFCI protection enough without bonding?

No. A GFCI trips when it senses leakage of about 4 to 6 milliamps on its own circuit. It cannot fix voltage differences that come from outside that circuit, such as a neighboring fault or stray current in the soil. Bonding keeps everything a swimmer touches at the same voltage. The NEC requires both because they protect against different problems.

How far does an outlet have to be from a pool?

General-purpose receptacles must be at least 6 feet from the inside walls of the pool, measured along the shortest path a cord would take. Every 125-volt through 250-volt receptacle within 20 feet must be GFCI protected, and at least one receptacle is required near the pool so people are not tempted to run extension cords. Confirm details for your code edition with your inspector.

Can I install pool equipment myself in Texas?

A Texas homeowner living in the home is exempt from state licensing unless a city ordinance regulates the work, and most big cities require permits. Professionals need a license: a residential appliance installer can connect a pool device to an existing circuit, but new circuits and bonding are work for a licensed electrician. Call your city building department before starting.

Does a pool contractor in Florida do the electrical work?

Florida pool/spa contractor licenses under s. 489.105 cover construction, equipment, heaters and piping, and their definitions do not list electrical power wiring. Circuits, panels and disconnects are electrical contracting, licensed by the Electrical Contractors' Licensing Board. Many pool companies hire or partner with a licensed electrical contractor. Ask who will pull the electrical permit and check that license on the DBPR site.

What is the Virginia Graeme Baker Act, and does it affect pool wiring?

The Virginia Graeme Baker Pool and Spa Safety Act is a federal law aimed at drain entrapment hazards in pools and spas, administered by the U.S. Consumer Product Safety Commission. We could not load CPSC's page to confirm its current details for this guide. It is not an electrical wiring law. Wiring and bonding rules come from NEC Article 680 as adopted in Texas and Florida.

How often should pool electrical be checked?

Test GFCIs monthly and after storms. Have a licensed electrician look over bonding, equipment and lights when you buy a home with a pool, after any deck or fence work nearby, after flooding, and any time someone feels a tingle. IAEI cites annual inspection by an electrician familiar with shock drowning hazards as a recommended practice for water-adjacent electrical systems.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration