Local Guide · Electricians
Home Wiring Types and Sizes Explained: Romex, Wire Gauges, Aluminum, Conduit and Amps
What 12/2 means, which wire size goes with which breaker, when conduit is required, how to read wire colors, and why concrete block homes in Florida are wired differently, with manufacturer data tied to NEC Table 310.16.
For copper NM-B (Romex-style) cable, the common match is 14 AWG on a 15-amp breaker, 12 AWG on 20 amps, 10 AWG on 30 amps, 8 AWG on 40 amps and 6 AWG on 55 amps, because NM-B is limited to its 60 C ampacity in NEC Table 310.16. Smaller numbers mean thicker wire. "12/2" means two 12-gauge insulated conductors plus a bare ground. Long runs may need a bigger size to limit voltage drop, and wet, buried or exposed locations need UF, THHN in conduit or other rated wiring.
Key facts
- Encore Wire's NM-B spec sheet lists allowable ampacities of 15 A for 14 AWG, 20 A for 12 AWG, 30 A for 10 AWG, 40 A for 8 AWG and 55 A for 6 AWG copper, based on NEC Table 310.16 with the limits in 240.4(D), 110.14(C) and 310.15.
- NM-B ampacity is limited to the 60 C column even though its inner conductors are 90 C rated (Encore Wire; Cerrowire).
- Cerrowire's ampacity chart (2017 NEC basis) shows 6 AWG copper at 55 A (60 C), 65 A (75 C) and 75 A (90 C).
- NM-B is rated for exposed and concealed work in normally dry locations and may be fished in air voids of masonry block or tile walls not exposed to excessive moisture or dampness (Encore Wire).
- UF-B may be direct-buried, including under concrete, but may not be embedded in concrete, and must be in a raceway if run underneath a building (Cerrowire).
- Cerrowire's voltage drop table shows a 120-volt, 20-amp copper circuit needs 12 AWG up to 50 feet but 8 AWG at 100 feet to stay within a 3 percent drop.
- Encore Wire jacket colors: 14/2 white, 14/3 blue, 12/2 yellow, 12/3 purple, 10/2 orange, 10/3 pink, 8 and 6 AWG black. Jacket colors are a manufacturer convention.
- NEMA's 2026 guidance says wire listed only for dry locations, such as NM-B, should be replaced after water exposure.
Wire gauge basics: AWG, amps and why smaller numbers are bigger wire
Wire size in U.S. homes is measured in AWG (American Wire Gauge). The number runs backward: 14 AWG is thinner than 12 AWG, which is thinner than 10 AWG. Larger conductors, like the ones feeding your panel, are sized in kcmil (thousands of circular mils). Cerrowire notes that kcmil and the older term MCM mean the same thing.
Thicker wire can carry more current without overheating. The safe continuous current a wire can carry is its ampacity. Three things set ampacity:
- Metal: copper carries more current than aluminum of the same size.
- Insulation temperature rating: 60 C, 75 C or 90 C. Higher-rated insulation tolerates more heat.
- Conditions: heat, bundling and how many wires share a conduit can reduce ampacity (NEC 310.15 adjustments).
The breaker protects the wire. If you put a 30-amp breaker on wire rated for 20 amps, the wire can overheat before the breaker trips. That is one of the hazards Florida's 4-point inspection form tells inspectors to look for ("improper breaker size" and "over-fusing").
What wire size do I need? The common breaker-to-wire table
This table uses manufacturer data that cites NEC Table 310.16. It covers copper NM-B cable, the plastic-sheathed cable used for most home branch circuits.
| Breaker | Copper NM-B size | Typical uses (Cerrowire examples) |
|---|---|---|
| 15 A | 14 AWG | Lighting circuits, light fixtures |
| 20 A | 12 AWG | General receptacles, kitchen and bath outlets, dishwashers, disposals, room AC, workshop tools |
| 30 A | 10 AWG | Electric dryers, water heaters, built-in single ovens, large AC up to 30 A |
| 40 A | 8 AWG | Ranges and cooktops (check nameplate) |
| Up to 55 A | 6 AWG | Double-oven ranges, built-in double ovens, many EV circuits |
Always follow the appliance's nameplate and installation instructions. They list the required circuit size. The table is a starting point, not a substitute for the label or your electrician's calculation.
What wire size for a 20-amp circuit?
12 AWG copper. Using 14 AWG on a 20-amp breaker is one of the most common amateur mistakes. Encore Wire's sheet points to NEC 240.4(D), the small-conductor rule that limits overcurrent protection on 14, 12 and 10 AWG wire.
What is the ampacity of 6 AWG copper?
It depends on the insulation column: 55 amps at 60 C, 65 at 75 C and 75 at 90 C (Cerrowire, 2017 NEC basis). In NM-B cable, use 55 amps because NM-B is limited to the 60 C column. As individual THHN wires in conduit with 75 C terminations, 65 amps is typical. Equipment terminals often set the limit, so your electrician checks the breaker and device ratings too.
What does 12/2 Romex mean? Reading the cable label
"Romex" is a brand name people use for NM-B (non-metallic sheathed) cable. The label printed on the jacket tells you what is inside:
- 12/2 with ground (12/2 W/G): two insulated 12 AWG conductors (usually black and white) plus a bare copper ground.
- 12/3 with ground: three insulated conductors (black, white and red) plus a bare ground. Used for 3-way switches and 240/120-volt loads.
- 14/2, 10/3, 6/3: same pattern at other sizes.
- NM-B: the cable type. The "B" refers to the 90 C rated conductors, but ampacity stays at the 60 C rating.
- 600V: voltage rating.
Encore Wire's spec lists the print legend: maker, size, "W/G," "TYPE NM-B 600V," the UL mark and date codes.
Jacket colors
Many manufacturers color-code the outer jacket by size so inspectors can spot mistakes. Encore Wire uses white for 14/2, blue for 14/3, yellow for 12/2, purple for 12/3, orange for 10/2, pink for 10/3, and black for 8 and 6 AWG. Other makers may use different colors, especially for 3-conductor cable, so the color is only a convenience. The printed size is what counts.
One more rule from Cerrowire: you cannot strip the inner wires out of NM-B and pull them through conduit as if they were THHN. They are not marked for that use.
What color wires mean what?
Inside a standard U.S. home, wire insulation colors follow NEC conventions:
| Color | Usual role |
|---|---|
| Black | Hot (ungrounded) conductor |
| Red | Second hot, for 240-volt circuits or 3-way switch travelers |
| Blue or yellow | Additional hots or travelers, often in conduit |
| White or gray | Neutral (grounded conductor); identified this way under NEC 200.6 |
| Bare copper or green | Equipment ground; identified this way under NEC 250.119 |
Important exceptions:
- In older switch loops and 240-volt cables, a white wire may be used as a hot. It should be re-marked with black or red tape, but often is not. Treat every wire as live until tested.
- Encore Wire's four-conductor NM-B uses black, white, red and blue, and its 2-2 cable uses black, red, white and white with a red stripe.
- Old homes may have cloth-covered wires with faded colors, or no ground at all. See ungrounded two-prong outlets.
Color tells you how a wire was supposed to be used, not how it is actually used. A non-contact tester and a meter are the only ways to be sure, and opening boxes on live circuits is a job for an electrician.
NM, UF, THHN, SER and armored cable: what is the difference?
| Type | What it is | Where it is used | Where it is not allowed or not ideal |
|---|---|---|---|
| NM-B (non-metallic sheathed) | Insulated conductors and bare ground in a plastic jacket | Most indoor branch circuits in dry locations, exposed or concealed | Wet or damp locations, embedded in concrete, places subject to damage |
| UF-B (underground feeder) | Conductors molded in a solid, moisture-resistant jacket | Direct burial to post lights, pumps, workshops; wet, dry or corrosive locations | Embedded in concrete; under a building unless in a raceway |
| THHN/THWN-2 | Single insulated conductors with a nylon jacket | Pulled in conduit for branch circuits, feeders and services; wet or dry at up to 90 C | Cannot be run loose without a raceway |
| USE-2 | Single conductors for underground service entrance | Direct burial service cables | Indoor wiring in most cases |
| SEU / SER | Service entrance cable | SEU from the service drop to the panel; SER from meter to panel in apartments and for large appliance circuits | Follow listing and local rules |
| MC or BX (armored cable) | Conductors inside a flexible metal sheath | Exposed areas, commercial work, some residential uses | Varies by type and local rules |
Sources: Cerrowire product applications and FAQs; Florida's 4-point form lists NM, BX and conduit as wiring types inspectors record.
When is conduit required in a house?
Most single-family homes in Texas and Florida are wired with NM-B cable, not conduit. Conduit (metal or plastic pipe with individual wires inside) is usually required or chosen when:
- The location is wet or damp. NM-B is rated for normally dry locations only. Outdoor runs, exterior walls with moisture, and underground runs need wet-rated wire such as THWN-2 in conduit, or UF-B.
- The wiring could be damaged. Exposed runs in garages, on exterior walls or near equipment often need conduit for protection.
- It runs in or under concrete. UF-B may be buried under a slab but not embedded in concrete, and under a building it must be in a raceway (Cerrowire). Wiring through a slab to a kitchen island is normally pulled in conduit.
- The service entrance is involved. Masts, risers and meter connections are typically conduit.
- Local code says so. Some cities and some building types (commercial and larger multifamily) require conduit or armored cable.
- Future access matters. Empty conduit to a garage, attic or future EV spot makes later upgrades easier.
Your permit office decides what is required for your job. Ask before buying materials.
Why are Florida houses wired differently? Block walls, slabs and moisture
Much of Florida's housing, especially in South Florida, Tampa Bay and older Jacksonville and Orlando neighborhoods, is built with concrete block (CBS) exterior walls on a concrete slab. That changes how wire gets from the panel to an outlet.
- Furring strips: many builders fasten wood or metal furring strips to the inside of exterior block walls, then run cable or small conduit in the space before drywall.
- Through the block cores: Encore Wire's NM-B data says the cable may be fished in air voids of masonry block or tile walls where the walls are not exposed to, or subject to, excessive moisture or dampness. Exterior walls that sweat or leak may not meet that condition, so inspectors and electricians often choose wet-rated wiring or conduit there.
- From above: wiring often drops down from the attic into walls, since the slab below cannot be fished.
- Slab work: circuits to islands or floor outlets run in conduit set before the pour.
Moisture and storms matter too. After flooding, NEMA's 2026 guidance says wire listed only for dry locations, such as NM-B, should be replaced. In homes where floodwater reached outlets, that can mean rewiring the lower walls. See flood-damaged electrical.
Texas homes are more often wood-framed, which makes fishing new cable easier, though slab-on-grade construction is common in Houston, Dallas and San Antonio and creates the same slab limits.
What is voltage drop and how long can a circuit run be?
Wire has resistance. The longer the run, the more voltage is lost before power reaches the load. Too much drop makes lights dim and motors run hot. Cerrowire's voltage drop guide says it is usually not a problem inside a house, but matters for runs to outbuildings, well pumps and similar long circuits.
Cerrowire's table for a 3 percent maximum drop (copper, single-phase, steel conduit, 86 F ambient):
| Circuit | 25 ft | 50 ft | 100 ft | 150 ft | 200 ft |
|---|---|---|---|---|---|
| 120 V, 15 A | 14 | 12 | 10 | 8 | 6 |
| 120 V, 20 A | 12 | 12 | 8 | 6 | 4 |
| 120 V, 30 A | 10 | 10 | 6 | 4 | 4 |
| 240 V, 20 A | 12 | 12 | 12 | 10 | 8 |
| 240 V, 30 A | 10 | 10 | 10 | 8 | 6 |
| 240 V, 50 A | 6 | 6 | 6 | 6 | 4 |
Example: a 120-volt, 20-amp circuit to a detached workshop 100 feet away needs 8 AWG copper, not 12 AWG, to stay within 3 percent. Running 240 volts instead cuts the needed size for the same load. Cerrowire's calculator lets you run your own numbers.
What wire do I need for a 50-amp EV circuit?
For a 50-amp, 240-volt circuit using copper NM-B, 6 AWG is the usual size because 6 AWG NM-B is rated 55 amps at 60 C, while 8 AWG is rated only 40 amps. Many electricians use 6/3 or 6/2 NM-B, or THHN in conduit, depending on the charger or receptacle.
Before you buy wire:
- Read the charger's installation manual. It specifies the breaker size, wire size and whether a neutral is needed. Chargers are often adjustable, and the circuit must match the setting.
- Check panel capacity. A large EV circuit may require a load calculation or an energy management device. See panel upgrades.
- Long run to the garage? At 200 feet, the Cerrowire table moves a 240-volt, 50-amp copper circuit up to 4 AWG.
- Permits. The U.S. Department of Energy says installations must follow state and local codes and may need permits. See EV charger installation.
Aluminum wire: dangerous branch circuits vs normal feeders
Aluminum gets a bad reputation, but the risk depends on what kind.
- Single-strand aluminum branch wiring (small 15- and 20-amp circuits) installed in some homes and additions from about 1965 to the mid-1970s is the hazard CPSC warns about. The danger is at connections: outlets, switches, junction boxes and appliances. CPSC's recognized permanent repairs are copper rewiring or pigtailing with COPALUM crimps or AlumiConn connectors. See aluminum wiring.
- Multistrand aluminum feeders and service conductors are widely used today for services, subpanel feeders and large appliance circuits. Florida's 4-point form lists single-strand and multistrand aluminum separately for that reason.
Can I use aluminum wire for a subpanel feeder?
Yes, commonly. Aluminum feeders are cheaper than copper for large sizes. They must be sized from the aluminum column (Cerrowire's chart shows, at 75 C, 2 AWG aluminum at 90 amps, 1/0 at 120 amps and 4/0 at 180 amps), landed on lugs rated for aluminum, and torqued to the manufacturer's specification. See subpanels for garages and additions.
Mistakes to avoid
- Putting 14 AWG wire on a 20-amp breaker, or upsizing a breaker because it "keeps tripping." See breaker keeps tripping.
- Running NM-B outdoors, underground or in wet areas.
- Burying UF-B directly in a concrete pour.
- Mixing aluminum and copper at a device not rated for both.
- Ignoring voltage drop on long runs to sheds and pumps.
- Assuming a white wire is always neutral.
- Reusing NM-B cable that sat in floodwater.
In Texas, homeowners may do work on the home they own and live in where no city ordinance regulates it; in Florida, owner-builders may wire their own single-family home under s. 489.503(6). Either way, permits and inspections usually apply. See DIY electrical rules.
Related electricians guides
- Subpanels for Garages, Workshops, ADUs and Additions: When You Need One, What It Costs and What Code Requires
- Aluminum Wiring: How Dangerous Is It, Which Fixes Work (COPALUM, AlumiConn) and What Do Texas and Florida Insurers Require?
- How Do You Install a Home EV Charger? Circuits, Panels, Permits, GFCI Rules and Cost in Texas and Florida
- Which Appliances Need a Dedicated Circuit? Kitchens, Ranges, Dryers, Mini-Splits, Tankless Heaters and Garages
- Why Does My Breaker Keep Tripping? Causes, Fixes and When It's Dangerous
- Flooded House Electrical: Is It Safe to Turn the Power Back On, and What Must Be Replaced?
- What Electrical Work Can You Legally and Safely Do Yourself in Texas and Florida?
- How Much Does It Cost to Rewire a House? Real Cost Data, the Process, Timeline and Living Through It
Electricians by state and city
Questions people ask
Can I use 14 gauge wire on a 20 amp breaker?
No. Copper 14 AWG NM-B is rated for 15 amps. A 20-amp breaker would let the wire overheat before tripping. NEC 240.4(D) limits overcurrent protection on small conductors. If a 14 AWG circuit trips, find the overload or fault instead of upsizing the breaker.
What size wire for a 30 amp dryer or water heater?
10 AWG copper is the usual match for a 30-amp circuit. Dryers typically use 10/3 with ground (two hots, neutral and ground). Water heaters often use 10/2 with ground. Always check the appliance nameplate and installation instructions, which list the required circuit size.
Is Romex allowed in conduit?
NM-B may be run through short sections of conduit for protection, but the inner conductors cannot be stripped out and used as THHN, because they are not marked for that use (Cerrowire). For long conduit runs, electricians pull individual THHN or THWN-2 conductors.
Can I bury Romex?
No. NM-B is for dry locations. Use UF-B for direct burial or wet-rated conductors in conduit. UF-B may be buried under concrete but not embedded in it, and must be in a raceway under a building. Ask your permit office for burial depth requirements.
Why is my Romex yellow?
Many manufacturers use yellow jackets for 12 AWG two-conductor NM-B so it is easy to spot. Encore Wire also uses white for 14/2, orange for 10/2 and black for 8 and 6 AWG. Check the printed label for the actual size.
Is copper-clad aluminum the same as aluminum wiring?
No. Copper-clad aluminum has a copper surface bonded to an aluminum core. Florida's 4-point form lists it as its own category, separate from single-strand and multistrand aluminum. Have an electrician confirm what you have and whether devices are rated for it.
What wire size for a 100 foot run to a shed?
It depends on the load and voltage. For a 120-volt, 20-amp circuit, Cerrowire's table calls for 8 AWG copper at 100 feet to stay within 3 percent drop. At 240 volts, 12 AWG works for 20 amps up to 100 feet. Use wet-rated or burial-rated wiring outdoors.
Does flooded wiring have to be replaced?
NEMA's 2026 guidance says wire listed only for dry locations, such as NM-B, should be replaced after water exposure. Wet-location wire may be reconditioned only if its ends were not exposed and it is undamaged, after consulting the manufacturer. Devices like GFCIs, AFCIs and outlets should be replaced.
Sources
- Encore Wire: Type NM-B copper specification sheet (Nov. 2024)
- Cerrowire: Ampacity charts (based on NEC Table 310.16, 2017 edition)
- Cerrowire: What type and gauge of wire should I use
- Cerrowire: Product applications (THHN, NM-B, UF-B, SER)
- Cerrowire: Voltage drop tables
- Cerrowire: Electrical FAQs
- CPSC: Repairing aluminum wiring (Pub. 516)
- Citizens Property Insurance: 4-Point Inspection Form Insp4pt 03 25 (hosted copy)
- NEMA CS 70006-2026: Evaluating water-damaged electrical equipment
- U.S. DOE Alternative Fuels Data Center: Charging at home
- NFPA 70 (National Electrical Code) code page
- Texas Occupations Code ch. 1305 (Texas Electrical Safety and Licensing Act)
- Florida Statutes s. 489.503 (electrical contracting exemptions)
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


