Local Guide · Foundation repair contractors
What Are Bell-Bottom and Drilled Concrete Piers, and Why Do Engineers Specify Them in Clay?
Drilled concrete piers are cast in place in a drilled hole, with a steel cage and sometimes a wide bell at the bottom. Here is how they resist Texas clay heave, what 'below the active zone' means, how long concrete needs before lifting, what the code says, and why Florida rarely uses them for home repair.
A drilled concrete pier is a round hole drilled under or beside a foundation, fitted with a steel reinforcing cage and filled with concrete poured on site. A bell-bottom pier has the bottom of the hole widened into a bell shape. The bell spreads the load over more soil and acts as an anchor so swelling clay cannot easily lift the pier. Engineers like them in clay because depth, size and steel are designed from soil data, not jack refusal. The trade-offs: more digging and a curing wait.
Key facts
- Florida Building Code 1810.3.9.5 says that where drilled shafts are belled, the bell's edge thickness may not be less than required for the edge of footings, and vertical shear must be considered when the bell's sides slope less than 60 degrees from horizontal.
- FBC 1810.3.9.2 requires cast-in-place deep foundations not enclosed in steel pipe to be reinforced where subject to uplift.
- FBC 1810.3.5.2.2 requires uncased cast-in-place elements to be at least 12 inches in diameter, with length no more than 30 times the diameter unless a registered design professional supervises design and installation.
- FBC 1810.3.3.1.4 caps assumed friction on uncased cast-in-place elements at one-sixth of the soil bearing value, up to 500 psf, unless a geotechnical investigation or load test supports more.
- FBC 1808.6.1 requires foundations penetrating expansive soils to be designed to prevent uplift and to resist forces from soil volume change, or be isolated from the soil.
- The Portland Cement Association says most of concrete's hydration and strength gain take place within the first month.
- ASCE Texas guidelines say that for major or comprehensive repairs, geotechnical information should come from a site-specific boring and testing program.
- This Old House (updated Oct. 8, 2026, Angi data) lists piering or underpinning at $1,000 to $3,000 per pier and a geotechnical soil report at $500 to $3,000.
What is a bell-bottom pier?
A drilled pier (the building code calls it a drilled shaft) is a column of reinforced concrete cast in a hole drilled into the ground. A bell-bottom pier, or belled pier, is a drilled pier whose bottom is widened with a special belling tool, so the base looks like an upside-down bell. A straight-shaft pier is the same thing without the bell.
For foundation repair, the steps are: drill a hole beside or under the grade beam, widen the base if a bell is specified, lower a steel reinforcing cage, pour concrete, let it gain strength, then set a cap and jack the house up onto it with shims. Unlike pressed piles and push piers, a drilled pier is not pushed into the ground against the house weight. Its depth and size come from the engineer's design.
Terms you will see
- Shaft: the column part of the pier.
- Bell or underream: the widened base.
- Reinforcing cage: tied steel bars (rebar) that run down the pier.
- Cap or pier cap: the top piece the house is shimmed onto.
- Spoil: the soil removed from the hole.
- Active zone: the upper layer of clay whose moisture, and so volume, changes with seasons.
Why do engineers like bell-bottom piers in clay?
Expansive clay shrinks when it dries and swells when it gets wet. A pier passing through that clay is gripped by it. When the clay swells, it pulls the pier up; when it shrinks, it can let the pier drop if the pier relied on friction in that layer. The building code puts the design goal in Florida Building Code 1808.6.1: foundations that extend into or penetrate expansive soils must be designed to prevent uplift of the structure and to resist forces from soil volume change, or be isolated from the expansive soil.
A bell-bottom pier answers that in three ways:
- Depth below the active zone. The base is placed in soil whose moisture stays fairly constant, so the bearing layer does not shrink and swell much.
- Anchorage. The wide bell is locked under stable soil. When swelling clay higher up tries to lift the shaft, the bell resists, like the head of a bolt under a board.
- Continuous steel. FBC 1810.3.9.2 requires cast-in-place deep foundations that are subject to uplift to be reinforced. A full-length rebar cage lets the pier carry the tension from that uplift instead of pulling apart.
The other reason engineers favor drilled piers is control. With jacked systems, depth is set by refusal and limited by the house weight. With a drilled pier, the engineer sets diameter, depth, bell size, steel and concrete strength on the plan, and the crew can see and measure the hole. The ASCE Texas guidelines say underpinning plans should show element locations, sizes, depths, material types and minimum required material strengths. Drilled piers make all of those items explicit.
What does 'below the active zone' mean for pier depth?
The active zone is the depth of clay that wets and dries with weather, watering and drainage. Below it, soil moisture changes much less. A pier founded below the active zone sits on soil that does not heave and shrink much, and the bell is anchored where the swelling forces above cannot easily lift it.
How deep the active zone is varies with climate, soil type, trees, drainage and how dry the ground has been. We did not find an official source that sets a standard depth for Texas, so we will not quote one. It is the engineer's job to estimate it, ideally from soil borings and lab tests. The ASCE Texas guidelines (7.4.2) say engineers need geotechnical information to design structural repairs, that it may come from successful local practice verified during construction, and that for major or comprehensive repairs it should come from a site-specific boring and testing program.
Ask your engineer: "What active-zone depth did you assume, what is it based on, and how far below it is the bell?" For background on clay behavior, see expansive clay soil in Texas.
What the building code says about drilled piers
Residential repairs are not always designed under the commercial deep foundation chapter, but these Florida Building Code 2023 sections, based on the International Building Code, show how engineers think about drilled piers. Texas cities adopt their own code editions, so confirm locally.
| Section | What it says | Why it matters to you |
|---|---|---|
| 1810.3.5.2.2 | Uncased cast-in-place elements at least 12 inches in diameter; length not over 30 times diameter unless a registered design professional supervises design and installation and reports to the building official | Very slender, deep, uncased piers need extra engineering oversight |
| 1810.3.9.2 | Cast-in-place deep foundations not enclosed in steel pipe must be reinforced where subject to uplift | In swelling clay, expect full rebar |
| 1810.3.9.3 | Reinforcement assembled and placed as a unit before concrete; exception allows placement in semifluid concrete for R-3 and U occupancies up to two stories of light-frame construction if the building official is satisfied | Houses have a narrow exception; ask how steel is placed |
| 1810.3.9.5 | Bell edge thickness no less than required for footing edges; vertical shear considered when bell sides slope under 60 degrees from horizontal | Bell shape is engineered, not just "as wide as possible" |
| 1810.3.3.1.4 | Assumed friction on uncased cast-in-place elements capped at one-sixth of bearing value, up to 500 psf, unless geotechnical data or a load test justifies more; friction and end bearing not assumed together unless a geotechnical investigation supports it | Friction in clay is limited unless backed by soil data |
| 1810.4.1.2 | Open holes through unstable soils must be stabilized by casing, slurry or another approved method before concrete | Caving sand or water needs casing or slurry |
| 1810.3.3.1.7 | Deep foundation elements must develop ultimate capacity of at least twice the design working load | Shows the safety margin engineers expect |
How long does a drilled pier cure before lifting?
Concrete gets stronger as it cures. The Portland Cement Association says most of the hydration and strength gain take place within the first month, and that longer moist curing produces stronger, more durable concrete. That is why drilled pier jobs usually include a waiting period between pouring the piers and jacking the house onto them.
We did not find an official source that sets a standard wait in days for residential repair, and it depends on the concrete mix, weather and the strength the engineer requires. The right answer for your job is whatever the engineer's specification says. Ask:
- What concrete strength is specified, and at what age?
- Will test cylinders or another method confirm strength before lifting?
- How long will the holes and pits stay open, and how will they be protected?
- Is the wait in the schedule and the price?
If a contractor proposes a high early-strength mix to shorten the wait, get the engineer's written approval first.
Drilled piers vs pressed piles vs push piers: which lasts longer?
No source we found compares lifespans by method with dated data, so we will not claim one lasts a set number of years longer. What we can compare is how each method deals with the things that make repairs fail.
| Failure driver | Drilled bell-bottom piers | Pressed concrete piles | Steel push piers |
|---|---|---|---|
| Depth control | Set by design, measured in the open hole | Set by jack refusal | Set by drive refusal |
| Uplift from swelling clay | Bell and rebar designed to resist | Limited unless cabled and designed | Limited |
| Material durability | Concrete with steel inside; cover matters | Concrete | Steel; needs corrosion protection |
| Capacity proof | Calculations and soil data; no installation load test | Jack pressure at refusal | Drive pressure at refusal |
| Wait before loading | Yes, concrete must gain strength | No | No |
| Disruption | Most digging and spoil | Moderate | Moderate |
One honest caution about drilled piers: because they are not pushed against the house, nobody gets a proof load during installation. Their reliability depends on the soil data and design. That is why a geotechnical report matters more for this method. See pressed concrete piles, steel push piers, helical piers, and the full methods comparison.
Do drilled piers need a geotechnical report?
Not always by law, but often by good practice. The ASCE Texas guidelines say the engineer designing structural repairs needs geotechnical information; for smaller repairs it may come from local experience verified during construction, but for major or comprehensive remedial measures it should come from a site-specific boring and testing program. Under the Florida Building Code, geotechnical investigations that involve in-situ testing, lab testing or engineering calculations must be done by a registered design professional (1803.1).
A geotechnical report for drilled piers usually tells the engineer soil layers, plasticity (how much the clay swells), moisture, groundwater and bearing values. Those feed the design depth, bell size and steel. This Old House (October 8, 2026, Angi data) lists a geotechnical soil report at $500 to $3,000 and a structural engineer report at $500 to $1,000. On a repair that uses many drilled piers, that cost is small relative to the work it guides.
See foundation inspections and structural engineers.
Access and spoil: exterior vs interior piers
Drilled piers need more room and produce more dirt than jacked methods. Each hole removes a column of soil, plus more for the bell. Exterior piers can sometimes be drilled with a small rig; tight side yards may require hand augers. Interior piers are the hard part.
- Through the floor: flooring is removed, the slab is cut, the hole is drilled and belled, and the slab and flooring are restored. Expect dust, noise and spoil carried out by hand.
- By tunnel: crews tunnel under the slab from outside to reach interior beams. That avoids breaking floors but leaves tunnels that must be backfilled and compacted carefully, since loose fill under a slab can settle.
- Spoil handling: ask where the soil goes. Spoil piled against the house can block drainage and hold water against the foundation.
- Open holes: holes left open during curing need covers and fencing. In wet weather, ask how water in the holes will be removed before concrete is placed.
When lifting is included, the ASCE Texas guidelines (7.6) call for testing water supply and drain lines for leaks and repairing leaks found. Interior work near plumbing raises that need. See slab leaks and foundation repair.
When do engineers specify drilled piers?
From the engineering principles in the ASCE Texas guidelines and the code sections above, drilled piers are a natural fit when:
- The soil is deep, highly expansive clay and the design must resist uplift.
- The engineer wants depth and bearing set by design rather than by jack refusal.
- Soil borings are available or justified.
- The structure is heavy enough, or the slab must be supported over long spans, so large capacity per pier is useful.
- The owner accepts more disruption and a curing wait.
They are a poorer fit where groundwater or caving sand makes open holes hard to keep stable (FBC 1810.4.1.2 requires casing or slurry in unstable soils), where access is very tight, or where the schedule cannot accept a curing period.
Texas: rules and city requirements
Engineer. Texas Occupations Code 1001.056(c)(2) removes the private-dwelling engineering exemption for design to repair a residential slab on expansive soil classified under the locally applied IRC, unless the work meets those requirements. Plans issued by a Texas engineer must be sealed (1001.401). The ASCE guidelines also note that the engineer who seals remediation documents is the engineer of record with approval authority over changes, and that Texas rules prohibit "plan stamping."
| City | Foundation repair requirement |
|---|---|
| Houston | Plans by a Texas-licensed engineer showing the location, quantity and type of supports; pre-construction and final inspections; listed processing 1 to 5 business days; extra floodplain items in flood zones |
| Fort Worth | Engineered foundation plans and an engineered structural letter |
| San Antonio | Over-the-counter permit, form IB 172 |
| Austin | Repairs up to 128 square feet exempt; larger repairs confirm with Development Services |
| Dallas | Not confirmed from an official page; call Development Services |
See permits by city.
Why drilled bell piers are rare in Florida home repair
We did not find a Florida survey counting pier types, so treat this as engineering reasoning to confirm with a Florida engineer.
- The soil problem is different. Bells are a tool against swelling clay uplift. Much of Florida's foundation trouble comes from loose sand, organic layers and sinkhole raveling above limestone, which the Florida Geological Survey describes as voids formed when slightly acidic groundwater dissolves the rock.
- Open holes in sand and water. Bells are hard to cut and hold in loose sand, and high groundwater complicates open holes. FBC 1810.4.1.2 requires casing or slurry where soils are unstable.
- Sinkhole repairs use other tools. The Florida Geological Survey lists grout and foam injection and engineered reinforced plugs, pins and porous concrete as sinkhole repair techniques. Under Florida Statutes 627.707(5), verified sinkhole repairs follow the insurer's engineer's recommendations; payment can be limited to actual cash value, without underpinning or grouting, until the owner signs a repair contract within 90 days of coverage confirmation, and repairs generally finish within 12 months.
Florida does have expansive soils in places. FBC 1803.5.3 requires soil tests where expansive soil is likely, and FBC 1808.6 sets design rules for it. Florida requires permits for building repairs (553.79), and engineering must be done and sealed by licensed engineers (471.003, 471.025). See the sinkhole claim process.
What does a bell-bottom pier cost?
The current named, dated source we use is This Old House, updated October 8, 2026, using Angi market research. It lists piering or underpinning at $1,000 to $3,000 per pier nationally and does not break out drilled or belled piers. From the same source: structural engineer report $500 to $1,000, geotechnical soil report $500 to $3,000, permits $75 to $150, and a contingency of $1,000 to $2,500. It also notes that homes on expansive clay, as in parts of Texas, are more likely to need costlier solutions like piering.
Drilled pier bids vary with depth, diameter, bell size, steel, concrete, interior access, tunneling, spoil removal and the curing wait. Ask each bidder to price the same sealed plan. See foundation repair cost and comparing quotes.
How to choose a provider
- Ask whether a site-specific geotechnical report is warranted for your repair.
- Get a sealed plan showing pier locations, diameter, depth, bell size, rebar and concrete strength.
- Ask what active-zone depth was assumed and how far below it the bell sits.
- Confirm how holes will be kept stable and dry before concrete, especially with groundwater.
- Confirm the required concrete strength and how it will be verified before lifting.
- Get the curing wait in the schedule and price.
- Agree where spoil goes and how tunnels or slab cuts will be backfilled and restored.
- Put plumbing tests before and after lifting in the contract.
- Confirm the permit and inspections.
- Get a post-repair elevation survey and the engineer's letter of substantial completion.
- Fix drainage and gutters so water does not collect near the foundation.
Related foundation repair contractors guides
- Which Foundation Repair Method Is Best? Piers, Piles, Slabjacking and Foam Compared
- What Are Pressed Concrete Piles, and Are They the Right Foundation Repair for Your House?
- What Are Steel Push Piers, and How Do You Know They Will Hold?
- What Are Helical Piers, and When Do They Make Sense for a Texas or Florida Foundation?
- Expansive Clay Soil and Your Foundation: Why Do Texas Homes Move?
- What Does a Structural Engineer Foundation Inspection Cost, and What Do You Get?
- How Much Does Foundation Repair Cost in Texas and Florida? Real Price Ranges by Method
- Do You Need a Permit for Foundation Repair? City-by-City Rules in Texas and Florida
Foundation repair contractors by state and city
Questions people ask
What is a bell-bottom pier?
It is a drilled concrete pier with a widened base. A hole is drilled, the bottom is enlarged into a bell, a steel cage is set, and concrete is poured. The bell spreads load and anchors the pier against swelling clay that might lift it. Engineers use it when they want depth and size set by design rather than jack refusal.
How deep are drilled piers for foundation repair?
The engineer sets the depth, ideally below the active zone of clay, based on soil data. There is no single standard depth. Ask what active-zone depth the design assumed and what borings or local data it is based on. The 2023 Florida Building Code limits uncased cast-in-place elements to 30 times their diameter unless a registered design professional supervises, so very deep piers also change the paperwork.
How long do drilled piers cure before lifting?
Concrete must gain strength before the house is set on it. The Portland Cement Association says most strength gain happens in the first month. The exact wait depends on the mix and the strength the engineer specifies. Ask how strength will be verified before lifting.
Drilled piers vs pressed piles: which lasts longer?
We found no dated data comparing lifespans. Drilled bell piers give more design control and uplift resistance in clay, but get no proof load during installation. Pressed piles are faster and get a jack test, but depth is set by refusal and segments may not resist uplift. The soil and design matter more than the label.
Do drilled piers need a geotechnical report?
For major or comprehensive repairs, the ASCE Texas guidelines say geotechnical information should come from site-specific borings and testing. For smaller jobs, local experience verified during construction may be used. A soil report costs $500 to $3,000 per This Old House (2026).
Can drilled piers be installed inside the house?
Yes, by cutting through the slab and flooring or by tunneling under the slab from outside. Interior drilled piers are messier and slower than exterior ones, and tunnels need careful backfill and compaction. Ask how spoil will be removed, how floors will be protected, and whether the engineer will check the tunnel backfill before flooring goes back.
What is a straight-shaft drilled pier?
It is a drilled concrete pier without a bell. It relies on its tip and side resistance. Where uplift from swelling clay is a concern, engineers may choose a bell, extra depth or more steel. FBC 1810.3.9.2 requires reinforcement in cast-in-place piers subject to uplift.
Why are bell-bottom piers rare in Florida?
Florida's main foundation issues are often loose sand and sinkhole raveling over limestone rather than swelling clay. Open bells are hard to hold in sand and groundwater, and sinkhole repairs usually rely on grouting, plugs, pins or deep steel piers under the insurer's engineer's plan.
What does a bell-bottom pier cost?
This Old House (Oct. 8, 2026, Angi data) lists piering or underpinning at $1,000 to $3,000 per pier nationally, without a separate figure for drilled piers. Depth, diameter, bell size, interior access and spoil removal drive local prices. The same source puts a structural engineer report at $500 to $1,000 and a soil report at $500 to $3,000. Ask every bidder to price the same sealed plan.
Sources
- Florida Building Code, Building, 8th Edition (2023), Chapter 18 Soils and Foundations (UpCodes)
- Portland Cement Association: Curing in Construction
- ASCE Texas Section, Guidelines for the Evaluation and Repair of Residential Foundations, Version 3 (2022)
- This Old House, How Much Does Foundation Repair Cost? (updated Oct. 8, 2026, Angi market research)
- Texas Occupations Code Chapter 1001 (Texas Engineering Practice Act)
- Houston Permitting Center: Foundation Repair permit requirements
- City of Fort Worth, Residential Remodel Checklist and Packet (05/27/2026)
- City of San Antonio Development Services: Residential Permits
- City of Austin Development Services: Work Exempt from Building Permits
- Florida Geological Survey (FDEP): Sinkholes
- Florida Geological Survey (FDEP): Sinkhole FAQ
- Florida Statutes 627.707 (2025), Standards for investigation of sinkhole claims
- Florida Statutes 553.79 (2025), Permits; applications; issuance; inspections
- Florida Statutes 471.003 (2025), Qualifications for practice; exemptions
- Florida Statutes 471.025 (2025), Seals
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


