Local Guide · Foundation repair contractors
How Do You Level and Anchor a Manufactured Home in Texas or Florida?
Manufactured homes sit on piers, pads and anchors, not a poured foundation. Here is what federal, Texas and Florida rules require, when to re-level, who may do it, and what it costs.
A manufactured home is adequately level under HUD's rules when adjacent piers differ by no more than 1/4 inch and doors and windows do not bind (24 CFR 3285.6). No Texas, Florida or federal rule sets a re-leveling schedule, so check it every year and after droughts, storms, leaks or floods. Leveling counts as installation work, so in Texas it needs a TDHCA-licensed installer and in Florida an FLHSMV-licensed installer.
Key facts
- HUD's Model Installation Standards define an adequately leveled manufactured home as one with no more than 1/4 inch difference between adjacent piers and doors and windows that do not bind (24 CFR 3285.6).
- Federal standards require frame piers within 24 inches of each end and no more than 120 inches apart under the main rails, unless an engineer designs otherwise (24 CFR 3285.310).
- Ground anchors for new installations must meet a 3,150-pound working load and 4,725-pound ultimate load in their rated soil class (24 CFR 3285.402); Florida requires 4,000/6,000-pound anchors for homes built after July 13, 1994 (Fla. Admin. Code r. 15C-1.0104).
- Texas defines installation to include leveling and requires an installer's license from TDHCA's Manufactured Housing Division, with training and a $25,000 bond (Tex. Occ. Code 1201.003, 1201.101, 1201.104, 1201.106).
- Florida requires any person who installs a mobile home to hold an annual FLHSMV installer license, with a bond of up to $5,000, liability insurance of up to $100,000, an 8-hour course and an exam (Fla. Stat. 320.8249).
- Fifteen Texas coastal counties, including Galveston, Brazoria and Nueces, are Wind Zone II (Tex. Occ. Code 1201.256); 14 Florida counties, including Miami-Dade, Broward, Palm Beach and Pinellas, are Wind Zone III (24 CFR 3280.305).
- Florida requires at least 18 inches between grade and the bottom of the I-beam, stricter than the federal 12-inch minimum (Fla. Admin. Code r. 15C-1.0103; 24 CFR 3285.305).
- Texas installers must warrant their work in writing; absent a longer warranty, defects must be reported in writing within two years of purchase or installation (Tex. Occ. Code 1201.361).
What makes a manufactured home foundation different from a site-built house?
A site-built house in Houston or Tampa usually sits on a concrete slab or on piers and beams that were built in place. A manufactured home is different. It is built in a factory on a steel chassis, hauled to the lot in one or more sections, and then set on a support system of piers, pads and ground anchors. That support system is the foundation. When people say a mobile home needs "leveling," they mean the piers under the steel frame need to be adjusted, reshimmed, reset or replaced so the floor is flat again.
Some terms first, because the law uses them carefully:
- Mobile home. Texas law defines a mobile home as a structure built before June 15, 1976, on a permanent chassis, designed to be used as a dwelling with or without a permanent foundation (Tex. Occ. Code 1201.003(20)).
- HUD-code manufactured home. A home built after that date to the federal Manufactured Home Construction and Safety Standards in 24 CFR part 3280. It carries a HUD label and a data plate.
- Installation or setup. Texas defines installation as building the temporary or permanent foundation system and placing the home on it, including "supporting, blocking, leveling, securing, anchoring" and connecting sections (Tex. Occ. Code 1201.003(13)). Florida's definition of "setup" also includes blocking, leveling, supporting and installing foundation products (Fla. Stat. 320.822(14)).
- Modular home. A factory-built home built to state and local building codes rather than the HUD code. In Texas these fall under the Industrialized Housing and Buildings program at the Texas Department of Licensing and Regulation, not the manufactured housing rules on this page.
That definition point matters more than it looks. Because both states count leveling as part of installation, re-leveling a manufactured home is regulated installation work, not general handyman work. We cover what that means for licensing below.
If your home is a site-built house on piers and beams, read pier-and-beam foundation repair instead. If you are not sure what is under your house, slab vs pier and beam explains how to tell.
What federal rules set the baseline for piers, pads and anchors?
HUD's Model Installation Standards in 24 CFR part 3285 set the minimum rules for the first installation of a new manufactured home. Each manufacturer's installation manual must meet or beat them (24 CFR 3285.1, 3285.2). They are written for initial installation, but they are also the best yardstick for judging whether an older home is supported properly, and many re-leveling crews and inspectors use them that way. The standards do not apply to a home placed on a site-built permanent foundation when the manufacturer certifies it under 24 CFR 3282.12 (24 CFR 3285.1(b)).
Here are the numbers that matter most for leveling:
| Item | Federal minimum (24 CFR part 3285) |
|---|---|
| What "level" means | No more than 1/4 inch difference between adjacent pier supports, and exterior doors and windows do not bind (3285.6) |
| Soil under footings | Firm, undisturbed soil or fill compacted to at least 90 percent of maximum density; grass, roots and wood scraps removed (3285.201) |
| Soil bearing value | Set by soil test, local soil records, the soil table, or a pocket penetrometer; 1,500 psf may be assumed unless site information calls for a lower value (3285.202) |
| Drainage | Ground slopes at least 1/2 inch per foot away from the home for the first 10 feet, or drains, swales or a sump system are provided (3285.203) |
| Vapor retarder | At least 6-mil polyethylene over the ground when the underside is skirted, with joints overlapped 12 inches (3285.204) |
| Clearance | At least 12 inches between the bottom of the main frame and the ground (3285.305) |
| Block piers | Load-bearing blocks at least 8 x 8 x 16 inches, cells vertical; piers 36 to 67 inches high and corner piers over three blocks must be double, interlocked blocks; piers over 67 inches must be designed by an engineer or architect (3285.304, 3285.306) |
| Shims | Used in pairs, driven tight, taking no more than 1 inch of height; remaining gaps filled with hardwood plates no thicker than 2 inches or with 2-inch or 4-inch concrete block (3285.304(c)) |
| Adjustable steel piers | Must be listed and labeled; adjustable risers may not extend more than 2 inches when finally set (3285.304(d), 3285.308) |
| Frame pier spacing | No more than 24 inches from each end and no more than 120 inches on center under the main rails, unless an engineer designs otherwise (3285.310(c)) |
| Ground anchors | Listed or certified; tested to a 3,150-pound working load and 4,725-pound ultimate load in the weakest soil class they are rated for (3285.402) |
| Crawl space vents | 1 square foot of vent per 150 square feet of floor, reducible to 1 per 1,500 with a full ground vapor retarder (3285.505) |
Two rules in that table drive most leveling disputes. First, the 1/4-inch rule between neighboring piers is the federal definition of "adequately leveled." It does not say the whole home must be dead flat end to end, only that neighboring supports are close and doors and windows work. Second, shims are limited. A home held up by stacks of loose wood wedges, or by an adjustable pier cranked out far past 2 inches, is not supported the way the standard expects.
The soil table in 3285.202 also tells you why soil matters. It lists rock at 4,000-plus psf, sandy gravel and dense sands at 2,000 psf, sand and silty or clayey sand at 1,500 psf, loose sands and firm clays at 1,000 psf, and puts uncompacted fill, peat and organic clays in a class that needs site-specific treatment. Pads sized for 1,500 psf soil will sink on soft clay or organic muck.
What are the signs a manufactured home needs leveling?
The federal definition gives you two simple tests: neighboring supports within 1/4 inch, and doors and windows that open and close without binding (24 CFR 3285.6). When a home drifts out of level, you usually see it inside first.
- Doors that stick, swing open or shut on their own, or will not latch.
- Windows that bind or show gaps at one corner.
- Cracks in interior wall panels, especially above doors and windows, or ceiling panels pulling apart.
- In a multi-section home, a gap or crack along the marriage line, the seam where the sections meet, in the ceiling, floor or roof.
- Floors that feel soft, bouncy or sloped, or a marble that rolls steadily to one side.
- Skirting that buckles, bows or pulls loose, which often means the home has dropped onto it.
- Plumbing drains that run slowly or water lines that leak at fittings after the home shifts.
Then look underneath, with a flashlight, from the access opening if you cannot crawl safely:
- Piers that lean, are cracked, have shifted off their pads, or have loose shims on the ground.
- Pads that have sunk into the soil, tipped, or broken.
- Standing water, mud, or soil washed away from pads after rain.
- Tie-down straps that are loose, rusted through, cut, or pulled at an angle, and anchor heads that have lifted out of the ground.
- A torn or missing vapor retarder, or wet, moldy subfloor.
Not every sticking door is a support problem. Soft floor spots can be water damage to the subfloor, and some cracks are just panel seams. But if several of these show up together, or the marriage line is opening, have the home checked. Our broader signs of foundation problems guide covers how to document what you see.
How to check level yourself without going under the home
- Use a long carpenter's level or a laser level on the floor along the main hallway and across each room.
- Write down where the floor drops and how much over what distance.
- Open and close every exterior door and window and note the ones that bind.
- Take dated photos of any cracks, with a tape measure in the shot, and recheck monthly. A crack that grows is more important than one that does not.
Why do manufactured homes go out of level in Texas and Florida?
The support system is simple, which is both its strength and its weakness. Each pier puts the weight of the home onto a small pad sitting near the surface. Anything that changes the soil under those pads, or the water around them, shows up as movement.
Texas: clay that swells and shrinks
Much of central and north Texas, including the Dallas-Fort Worth and Austin-San Antonio corridors, has expansive clay that swells when wet and shrinks when dry. A pad that sits on clay rises in a wet spring and drops in a drought summer. Because a manufactured home's pads are shallow, they ride the top layer of soil, which is the layer that changes the most. The federal soil table rates firm clays at only 1,000 psf, and notes that for high-plasticity CH clays without test data, anchors must be rated for the weaker 4B soil class (24 CFR 3285.202). The U.S. Drought Monitor showed 43.07 percent of Texas in moderate drought or worse on Nov. 17, 2026, which is the kind of condition that shrinks clay under pads. See expansive clay soil in Texas and drought and foundation watering for more.
Texas law recognizes the drainage risk directly. An installer may not install a used manufactured home on a site with evidence of ponding, runoff under heavy rains, or bare uncompacted soil unless the owner first signs a state form saying those conditions may cause problems with the stabilization system and accepts that risk (Tex. Occ. Code 1201.255(b)).
Florida: sand, muck, high water and sinkholes
Florida's problems are different. Sandy soils drain fast but can wash out from under pads when roof water pours off one spot. Low areas have organic muck and peat, which the federal soil table puts in its weakest class (24 CFR 3285.202). A high water table keeps the ground under the home damp. In west-central Florida, karst limestone can produce sinkholes and slow subsidence. The Florida Geological Survey lists compressing organic layers, rotting buried stumps or debris, broken sewer or septic lines, and poorly compacted soil as causes that can look like sinkholes. Florida's rule for setup requires the ground under the home to be cleared of vegetation, stumps and roots and graded so water will not collect under the home (Fla. Admin. Code r. 15C-1.0102(3)). See sinkhole signs and testing in Florida.
Causes that apply in both states
- Roof runoff with no gutters, or downspouts dumping next to the home. See drainage, gutters and grading.
- Plumbing leaks under the home that soften soil around pads.
- Pads that were too small for the soil, or placed on loose fill or on grass and roots.
- Wood piers or shims that rot, and steel piers that rust.
- Added weight the support system was not designed for, such as heavy furniture, a waterbed, a hot tub on an attached deck, or an addition that leans on the home. HUD recommends that an attached addition carry its own loads unless it is covered in the installation instructions or designed by an engineer or architect (24 CFR 3285.903(c)).
- Wind and flood events that loosen anchors or scour soil.
How often should a mobile home be re-leveled?
No federal or state rule we found sets a re-leveling schedule. Neither 24 CFR part 3285, Texas Occupations Code chapter 1201, nor Florida's rule 15C-1 says a home must be re-leveled every set number of years. Any fixed interval you see online is a sales rule of thumb, not a code requirement.
A better approach is to check on a schedule and level when the checks say so:
- First year after setup. New pads and disturbed soil settle the most early on. Many owners have the home checked within the first year, and in Texas any installation defect should be reported in writing within the installer warranty window covered below.
- Every year. Look under the home for leaning piers, sunken pads, loose straps and water. Do the door and floor checks above.
- After triggers. A long drought or a very wet season on Texas clay, a hurricane or tropical storm in Florida, a plumbing leak, a flood, or any time the home is moved.
- Before you buy or sell. A level check and an under-home inspection are cheap compared with the repairs a hidden problem can lead to.
Homes on stable, well-drained sites with properly sized pads may go many years without adjustment. Homes on reactive clay, or with poor drainage, may need attention far more often. The site, not the calendar, decides.
What does re-leveling involve, step by step?
Re-leveling is adjusting the support system so the frame is back within tolerance. A typical job goes like this:
- Inspection and measurement. The installer checks pier condition, pad condition, soil, drainage, anchors and straps, and takes level readings along each main I-beam and the marriage line.
- Find the cause. A good crew asks why the home moved. Re-leveling without fixing a leak or a downspout that floods one corner just resets the clock.
- Loosen tie-downs where needed. Straps may need to be loosened so the frame can move. They must be retensioned at the end.
- Jack the frame. Hydraulic jacks are placed under the I-beams at approved points and raised slowly, a little at a time, across several points so the frame is not twisted.
- Repair or replace supports. Sunken pads are reset on firm soil or replaced with larger pads. Cracked blocks, rotten wood, and rusted steel piers are replaced. Shims are reset in tight pairs within the 1-inch limit, and caps are used as the standard requires (24 CFR 3285.304).
- Lower and check. The frame is lowered onto the supports and re-measured against the 1/4-inch rule. Doors and windows are tested (24 CFR 3285.6).
- Re-secure anchors. Straps are retensioned or replaced, missing anchors added, and stabilizer plates checked. In Florida, all anchors, piers and tie-down parts must be tested, listed and approved by the state (Fla. Admin. Code r. 15C-1.0102(2)).
- Close up. Repair the vapor retarder, reattach skirting so it does not trap water (24 CFR 3285.504), and keep vents open.
Ask for a written summary listing every pier and pad replaced, the final level readings, and the anchors added or retensioned. That record is useful for insurance, warranty and resale.
Re-leveling vs replacing the support system
If most pads have sunk, the soil is soft, or the home sits on old dry-stacked blocks and wood, a full support rebuild may make more sense than another adjustment. That can mean new pads sized for the soil, new piers at correct spacing, new anchors rated for the soil class, and drainage work. On very poor soil, or for a home meant to stay put long term, owners sometimes move to an engineered permanent foundation, covered next.
What are the tie-down and anchoring rules, and what are wind zones?
Leveling holds the home up. Anchoring holds it down. After blocking and leveling, the home must be secured against wind with anchor assemblies or by connecting it to an engineered foundation system (24 CFR 3285.401(a)). A home that has been re-leveled but not re-anchored is not finished.
Wind zones in Texas and Florida
Federal construction standards divide the country into three wind zones. The zone is printed on the home's data plate, and a home may not be installed in a zone tougher than it was built for.
| Wind zone | Design wind speed | Texas counties | Florida counties |
|---|---|---|---|
| Zone I | Standard | All counties not in Zone II | None |
| Zone II | 100 mph | Aransas, Brazoria, Calhoun, Cameron, Chambers, Galveston, Jefferson, Kenedy, Kleberg, Matagorda, Nueces, Orange, Refugio, San Patricio, Willacy | All counties not in Zone III |
| Zone III | 110 mph | None | Broward, Charlotte, Collier, Dade (Miami-Dade), Franklin, Gulf, Hendry, Lee, Martin, Manatee, Monroe, Palm Beach, Pinellas, Sarasota |
Sources: 24 CFR 3280.305(c)(2); Tex. Occ. Code 1201.256. Texas law also says a home built on or after Sept. 1, 1997, must meet Zone II standards to be installed in a Zone II county, and a retailer selling a Zone I home must warn the buyer that it cannot be installed in a Texas Zone II county (Tex. Occ. Code 1201.256).
So Houston proper (Harris County) is Zone I under the Texas list, while neighboring Galveston, Brazoria and Chambers counties are Zone II. In Florida, every county is at least Zone II, and Miami-Dade, Broward, Palm Beach, Pinellas and the southwest Gulf counties are Zone III.
Federal anchoring points
- Anchors must be listed or certified and installed to full depth, with stabilizer plates where the listing requires (24 CFR 3285.402).
- Homes in Zones II and III must also have longitudinal anchoring at the ends of each section, certified by an engineer or architect (24 CFR 3285.402).
- Homes designed for Zone III must have a vertical tie at each diagonal tie location (Table 3 to 24 CFR 3285.402).
- Within 1,500 feet of a coastline in Zones II or III, the home must be designed for the higher loads shown on its data plate, and an engineer or architect must design anchorage where site conditions rule out the manufacturer's instructions (24 CFR 3285.405).
- Tie-down straps must be at least 1-1/4 inch by 0.035 inch steel with corrosion protection (24 CFR 3285.402).
Florida's stricter state rules
Florida has its own installation rules in Florida Administrative Code chapter 15C-1, adopted by the Department of Highway Safety and Motor Vehicles. Key points:
- Who may install. All installations must be done by a licensed installer, dealer installer or manufacturer installer (r. 15C-1.0102).
- Pads. Pier pads must be at least 4 x 16 x 16 inches of solid concrete or other state-listed material; where soil capacity is unknown, assume 1,000 psf or consult the local building authority (r. 15C-1.0102(3)). Concrete pads must be at least 2,500 psi (r. 15C-1.0103(2)).
- Pier spacing. When the manufacturer's instructions are not available, piers go under the I-beam no more than 8 feet apart, with the first within 2 feet of each end (r. 15C-1.0103(1)(a)).
- Pier height. Piers over 36 inches, and corner piers over 24 inches, must be double-tiered and interlocked; piers over 52 inches must meet local requirements; metal piers are limited to 24 inches plus a 4-inch locking adjustment (r. 15C-1.0103).
- Clearance. At least 18 inches between finished grade and the bottom of the I-beam, with up to 25 percent of the frame allowed lower on sloped sites but never below 12 inches (r. 15C-1.0103(1)(h)). That is stricter than the federal 12-inch minimum.
- Anchors. Augers must be galvanized and set in undisturbed or compacted soil. Homes made after July 13, 1994, use anchors with a 4,000-pound working load and 6,000-pound ultimate load (Type II); older homes use 3,150 and 4,725 pounds (Type I) (r. 15C-1.0102(4), 15C-1.0104(1)). The rule notes that coral anchors are not designed to meet Zone II and III wind requirements.
- Stabilizer plates. Each ground anchor needs a state-approved stabilizer of at least 180 square inches, set flush with the soil (r. 15C-1.0102(5)).
- Diagonal ties. In all wind zones, frame ties no more than 5 feet 4 inches apart on center, with anchors within 2 feet of each end (r. 15C-1.0104(2)(b)).
- Longitudinal ties. At least four anchors and straps at the end of each section, which works out to 16 on a double-wide (r. 15C-1.0104(3)).
- Exposure D. Florida has added rules for homes in "Exposure D," flat areas exposed to wind off large bodies of water, extending inland 1,500 feet or 10 times the building height (r. 15C-1.0101, 15C-1.01031).
Florida law also ties installation to wind insurance: insurers licensed to cover mobile and manufactured homes against windstorm may issue that coverage only if the home was installed under the state's rules (Fla. Stat. 320.8325(2)(a)). If a home that has windstorm coverage is later damaged in a way that shows it was not installed correctly, the insurer is not excused from the policy on that ground (Fla. Stat. 320.8325(2)(b)). Proper re-anchoring after a re-level is part of keeping a Florida home insurable.
What is a permanent foundation for a manufactured home?
A standard pier-and-anchor setup is often called a temporary or non-permanent foundation, even though homes sit on one for decades. A permanent foundation is an engineered system, often a perimeter concrete or masonry foundation wall with footings, or a concrete slab with anchoring, that ties the home to the ground in a way meant to last.
Federal rules allow foundation systems other than piers and footings when they are backed by engineering data, and require all foundation plans and test data to be designed and certified by a registered professional engineer or architect (24 CFR 3285.301). A monolithic slab system must also be designed by an engineer or architect (24 CFR 3285.312).
What HUD requires for FHA-insured homes
For a manufactured home to qualify for FHA insurance under HUD's rule at 24 CFR 203.43f, the home, if it has not been on its site for more than a year, must:
- Sit on a site-built permanent foundation that meets HUD's Minimum Property Standards, attached with anchoring adequate for all loads in those standards.
- Have its towing hitch and running gear (axles, wheels, brakes) removed.
- Have the finished grade under the home at or above the 100-year flood elevation.
- Have the space under the home enclosed by continuous foundation-type construction that resists the forces on it without passing them to the home, built of materials that meet the standards for foundations.
HUD's Permanent Foundations Guide for Manufactured Housing (HUD-4930.2) is the design reference usually cited for these foundations. We could not load an official copy of that guide from HUD's website when preparing this page, so we do not quote its details here. An engineer who designs manufactured home foundations can tell you which version applies and provide the certification a buyer's side will ask for.
Real property status in Texas
In Texas, a manufactured home's ownership record is a Statement of Ownership issued by the Texas Department of Housing and Community Affairs. An owner may elect to treat the home as real property only if it is attached to land the owner owns or holds under a long-term lease (Tex. Occ. Code 1201.2055), and the election takes effect only when a copy of the Statement of Ownership is filed in the county real property records (1201.222(a)). Installation of a home treated as real property must satisfy the FHA, Fannie Mae or Freddie Mac installation requirements (1201.222(c)). If you are changing the foundation as part of converting the home's status, check the TDHCA records first.
In Florida, ask your county property appraiser and tax collector how a home on owned land is classified, because the rules for real property status are handled locally and through the state's titling system.
Who licenses manufactured home installers in Texas?
The Texas Department of Housing and Community Affairs, through its Manufactured Housing Division (TDHCA MHD), licenses manufacturers, retailers, brokers, salespersons and installers under the Texas Manufactured Housing Standards Act, Texas Occupations Code chapter 1201. Its rules are in 10 Texas Administrative Code chapter 80.
What the law requires
- A license to act as an installer. "A person may not act as an installer in this state unless the person holds an installer's license" (Tex. Occ. Code 1201.101(d)). An installer is anyone, including a retailer or manufacturer, who contracts to perform or performs an installation function (1201.003(14)), and installation includes leveling (1201.003(13)). So a crew paid to re-level your home is doing licensed work.
- Training. New applicants must complete eight hours of instruction in the law, including consumer protection, plus four hours of specialized instruction on installation (1201.104(a), (a-3)).
- Bond. An installer must file a $25,000 bond or other security (1201.106(a)(4)).
- Helpers. A licensed installer may use unlicensed helpers but must keep a list of them (1201.102(a)). Licensed trades such as plumbing, electrical and air conditioning may be subcontracted to people holding those state licenses (1201.102(b)).
- One state standard. A city or county may not adopt a different installation standard unless the state board approves it after a hearing (1201.252).
Protections for Texas owners
- Installer's warranty. For all installations, the installer must give the owner a written warranty that the work meets state standards. Unless the warranty is longer, the installer has no liability for a defect reported in writing more than two years after the later of the purchase or installation date (1201.361). Report problems in writing, and keep a copy.
- Free state inspection. If the installer, retailer or manufacturer does not provide proper warranty service, the consumer may ask TDHCA for a consumer complaint home inspection at no charge (1201.355).
- State-ordered corrections. If TDHCA finds an installation that does not conform, it may order the installer to fix it, or reassign the fix to another licensed installer if the original one is no longer licensed (1201.362).
- Consumer claims program. For unsatisfied claims against a licensee that result from violations of the law, the program pays actual damages up to the lesser of reasonable costs or $35,000, not counting attorney's fees (1201.404, 1201.405).
- Deceptive trade practices. A violation of chapter 1201 is actionable under the Texas Deceptive Trade Practices Act (1201.603).
- Inspection program. The state must inspect at least 75 percent of installed homes on a sample basis, with priority on multi-section homes and Wind Zone II counties (1201.303(b)).
How to check an installer
TDHCA's Manufactured Housing Division website offers a records search for license holders, installation and inspection records, and ownership records (see tdhca.texas.gov/mhd). Texas law requires the department to keep those records searchable online (1201.010). Before you sign, confirm the installer's license is active and look for enforcement actions. For other Texas contractor checks, see Texas foundation repair licensing.
Who licenses manufactured home installers in Florida?
In Florida, mobile home installers are licensed by the Department of Highway Safety and Motor Vehicles (FLHSMV). The department's dealer services bureau says it licenses mobile home installers and monitors the construction and installation of mobile homes.
What the law requires
- A license to install. "Any person who installs a mobile home shall obtain a mobile home installers license" from the department, renewed every year for a $150 fee (Fla. Stat. 320.8249(1)). Installation means the same thing as setup (320.8249(6)), and setup includes blocking and leveling (320.822(14)).
- Qualifications. The applicant must be at least 18, hold a performance bond set by rule of up to $5,000 covering proper installation for one year, carry liability insurance set by rule of up to $100,000, finish an approved 8-hour training course, and pass a state exam (320.8249(3)).
- Employees. Direct employees working under a licensed installer's supervision do not need their own license, but the licensee is responsible for their work (320.8249(5)).
- No faking it. It is unlawful to falsely claim to be a licensed installer or to impersonate one (320.8249(7)).
- State standards only. The department adopts uniform installation standards that require a permanent foundation resisting wind, flood, flotation, overturning, sliding and lateral movement, and no other entity may amend them (Fla. Stat. 320.8325(1)).
- Owner responsibility. The statute makes the home's owner responsible for installation in line with department rules (320.8325(1)). In practice, that means you should hire a licensed installer and keep the paperwork.
Your remedies in Florida
If a business installs a home in a way that does not meet the state standards, a person harmed may sue for actual damages; the court may grant injunctions, must award punitive damages for a willful violation, and may award costs and attorney's fees to the winning side (Fla. Stat. 320.8325(3)). The department and state attorneys may also seek injunctions (320.8325(4)). This is general information; talk to a Florida attorney about a specific dispute. See foundation repair disputes and complaints.
Permits
Florida law makes it unlawful to construct, alter, repair or demolish a building without a permit from the local enforcement agency (Fla. Stat. 553.79(1)(a)), and local agencies must post their permit applications online (553.79(1)(b)). Counties and cities handle mobile home setup permits differently, and some treat re-leveling or tie-down replacement as permitted work. Call your county or city building department before work starts, and ask the installer who will pull the permit. For how the Florida contractor system works for site-built homes, see Florida foundation repair licensing.
Do you need a permit to re-level a mobile home?
It depends on the city or county, and on how much work is involved.
- Texas. State law sets installation standards statewide and limits local governments from adopting different standards without state approval (Tex. Occ. Code 1201.252). TDHCA runs the installation inspection program (1201.303). Some cities and counties still require local permits for setup, utility work, skirting, decks or additions. Ask the local building office, and ask the installer whether the job will be reported to TDHCA.
- Florida. Statewide law requires permits for building repairs (Fla. Stat. 553.79), and local building departments issue mobile home setup permits. Replacing piers and anchors is usually treated differently from simple shim adjustment. Ask before work starts.
- Floodplains. In a mapped flood zone, any substantial work may trigger floodplain review. Under federal rules, if repair or improvement costs reach 50 percent or more of the structure's market value, it is a "substantial improvement" or "substantial damage," which can require elevating the home to flood standards (44 CFR 59.1, 60.3).
Our foundation repair permits by city page covers how Houston, Dallas, San Antonio, Austin and Florida cities handle permits for site-built homes.
How do hurricanes and floods affect manufactured home foundations?
Wind tries to slide, lift and roll a manufactured home. Water tries to float it and wash soil from under its pads. Both attack the support system directly.
- Wind. Loose or rusted straps, anchors in soft soil, and missing longitudinal ties let a home shift on its piers. Even if it stays standing, a home that racked in the wind can drop off its supports. That is why Florida requires state-approved anchors, stabilizer plates and close tie spacing (r. 15C-1.0102, 15C-1.0104).
- Flood. In flood hazard areas, foundations, anchors and supports must resist flood and wind loads together and prevent flotation, collapse or lateral movement, and the manufacturer's instructions must state whether the foundation was designed for flood loads (24 CFR 3285.302).
- Scour. Moving water can undercut pads and anchors. After water goes down, pads may be tilted or sitting on loose, wet soil.
After a storm or flood
- Stay out if the home has shifted off its piers or is visibly leaning.
- Photograph the home from all sides and underneath from the access opening before anything is moved.
- Report damage to your insurer quickly. In Florida, most property claims must be reported within 1 year of the loss (Fla. Stat. 627.70132). In Texas, see Texas homeowners insurance and foundations.
- Have a licensed installer check every pier, pad, strap and anchor, even if the home looks fine.
- If the home is in a mapped flood zone, ask the local floodplain office whether the damage counts as substantial damage before repairs start (44 CFR 59.1).
Flood insurance through the NFIP generally does not cover loss caused directly by earth movement, even if flooding set it off, and it lists land subsidence, sinkholes and destabilization from subsurface water as examples (44 CFR part 61, Standard Flood Insurance Policy). Read flood and hurricane foundation damage for more on claims.
What does mobile home leveling cost?
We could not find a named, dated cost study for mobile home re-leveling alone, so we will not quote a number for it. Prices you see on installer ads are quotes, not data. Here is what we can source:
| Item | Reported range | Source and date |
|---|---|---|
| Mobile home floor repair, overall | $300 to $5,000; national average about $2,650 | Bob Vila, updated Jan. 11, 2024, citing Angi |
| Replace subfloor in a mobile home | $1,800 to $3,000; a damaged section $500 to $700 | Bob Vila, Jan. 11, 2024 |
| Reinforce floor joists | $100 to $300 per joist | Bob Vila, Jan. 11, 2024 |
| Replace all floor joists | $5,000 to $20,000; $1,000 to $10,000 if only a few | Bob Vila, Jan. 11, 2024 |
| Foundation repair labor, general | About $200 per hour | This Old House, updated Oct. 8, 2026 |
| Permit fees, general | $75 to $150 (varies by city) | This Old House, Oct. 8, 2026 |
The floor numbers matter because a home left out of level for a long time often has water and subfloor damage too. The labor and permit figures are national numbers for site-built foundation work, so treat them as a rough guide only.
What drives the price of a re-level
- Single-section vs multi-section. Multi-section homes have more piers and the marriage line to support.
- How many piers and pads must be reset or replaced, not just adjusted.
- Whether anchors and straps must be added or replaced to meet the wind zone, and in Florida whether parts must be state-listed.
- Access: low clearance, mud, debris or tight skirting slows the crew.
- Drainage fixes, vapor retarder replacement and skirting work.
- Travel distance and permit requirements.
Get at least two written quotes that list the number of piers, pads and anchors, the materials, the final level tolerance promised, and the warranty. Our quote comparison guide has a worksheet you can adapt.
Can I level a mobile home myself?
Physically, owners sometimes do. Legally and practically, it is a poor idea in both states.
- Texas. The license rule covers anyone who "performs an installation function" (Tex. Occ. Code 1201.003(14), 1201.101(d)), and leveling is an installation function. We did not find an owner exemption for installation work in chapter 1201. Ask TDHCA's Manufactured Housing Division before doing it yourself.
- Florida. The statute says "any person who installs a mobile home" must be licensed (Fla. Stat. 320.8249(1)), and the state rule says all installations must be done by a licensed installer, dealer installer or manufacturer installer (r. 15C-1.0102). Florida also ties windstorm insurance to installation under state rules (320.8325(2)).
- Safety. Jacking a steel frame unevenly can twist it, crack walls and break plumbing. Never work under a home held only by a jack.
What owners can safely do
- Fix drainage: add gutters, extend downspouts, and regrade so water flows away for 10 feet (24 CFR 3285.203).
- Keep vents open and the vapor retarder intact (24 CFR 3285.204, 3285.505).
- Fix plumbing leaks under the home quickly, using a licensed plumber where required.
- Check straps and anchors after storms and call an installer if any are loose, rusted or pulled.
- Keep the log described in the checklist below.
Our DIY foundation repair guide explains which jobs are owner-friendly for site-built homes too.
Buying or selling a manufactured home: what to check under it
Before you buy a manufactured home, look at the support system as carefully as the kitchen.
- Ask for the installation record and any re-leveling invoices. In Texas, TDHCA's records search includes installation and inspection records.
- Check the data plate for the wind zone, and make sure it matches the county.
- Look under the home for pier type, pad condition, spacing, and anchor and strap condition.
- Do the door, window and floor checks above.
- Check drainage around the home after rain if you can.
In Texas, a person selling a used manufactured home to a consumer for use as a dwelling must generally give a written condition disclosure on a state form and a written warranty that the home is and will remain habitable until 60 days after the later of installation or the purchase agreement; the buyer must report a defect that makes the home not habitable in writing within 65 days (Tex. Occ. Code 1201.455). That warranty requirement does not apply to a sale from one consumer to another (1201.456). For site-built homes, see buying a house with foundation problems.
If the home has been moved, note that manufacturer and retailer warranties in Texas do not cover defects or damage caused by moving a new HUD-code home from its first site (1201.359).
How to choose a provider
- Find the data plate and write down the home's wind zone, then confirm it matches your county list.
- Check level along the hallway and across rooms with a long level or laser, and test every exterior door and window.
- Once a year and after storms, look under the home for leaning piers, sunken pads, loose or rusted straps, lifted anchors and standing water.
- Fix drainage first: gutters, downspout extensions, and ground sloping away at least 1/2 inch per foot for 10 feet.
- Repair plumbing leaks under the home right away.
- Hire only a licensed installer: TDHCA MHD in Texas, FLHSMV in Florida, and verify the license before signing.
- Ask the installer what caused the movement and how the plan fixes it, not just how many piers will be adjusted.
- Get a written quote listing piers, pads, anchors, materials, final level tolerance and warranty.
- Ask who pulls any required local permit, and call the building department yourself if unsure.
- After the job, get final level readings and a list of all parts replaced, and keep them with your home records.
- In Texas, report installation defects to the installer in writing within the warranty period, and contact TDHCA if service is refused.
- In a flood zone, ask the floodplain office about the 50 percent substantial damage rule before major repairs.
Related foundation repair contractors guides
- How Do You Repair a Pier-and-Beam Foundation? Shimming, Re-Leveling, Rot and Crawl Spaces
- What Are the Signs of Foundation Problems? The Complete Checklist, Inside and Out
- How Do Drainage, Gutters and Grading Protect a Foundation?
- Can Flooding or a Hurricane Damage Your Foundation? Insurance, the 50% Rule and Repairs
- Who Regulates Foundation Repair in Texas? Licenses, Engineers and Consumer Protection
- Who Can Legally Repair a Foundation in Florida? Contractor, Engineer and Sinkhole Licensing
- Do You Need a Permit for Foundation Repair? City-by-City Rules in Texas and Florida
- DIY Foundation Repair: What Can Homeowners Safely Do Themselves, and What Should They Never Try?
Foundation repair contractors by state and city
Questions people ask
How often should a mobile home be re-leveled?
No federal or Texas or Florida rule sets a schedule. Check the home every year and after triggers such as a long drought on clay soil, a very wet season, a hurricane, a plumbing leak, a flood, or a move. Re-level when neighboring piers differ by more than 1/4 inch or doors and windows bind, which is the federal test for an adequately leveled home under 24 CFR 3285.6. Homes on reactive Texas clay or poorly drained Florida sites tend to need attention more often than homes on stable, well-drained ground.
What does a 1/4 inch level tolerance mean?
HUD's Model Installation Standards say a manufactured home is adequately leveled if there is no more than a 1/4 inch difference between adjacent pier supports, frame or perimeter, and exterior doors and windows do not bind and work properly (24 CFR 3285.6). It compares neighboring supports, not one end of the home to the other. A home can be slightly out of level end to end and still meet the rule, but if doors bind, it does not.
Is a mobile home with leaning piers dangerous?
It can be. A leaning or cracked pier carries less load and can fail, letting the frame drop onto other supports or the skirting. Federal standards require block piers to be stacked with cells vertical, capped, and limited in how far they can be offset from top to bottom (24 CFR 3285.304, 3285.306). If several piers lean or the home has visibly shifted, stay off that area and call a licensed installer. If the home has moved off its piers after a storm, stay out until it is checked.
Do I need a licensed installer to re-level my home in Texas?
Texas law says a person may not act as an installer without an installer's license, and defines installation to include leveling (Tex. Occ. Code 1201.003(13), 1201.101(d)). Installers must complete required training and file a $25,000 bond. Check the installer's license on the TDHCA Manufactured Housing Division records search before you sign. If you want to do the work yourself, ask TDHCA first, because we did not find an owner exemption in chapter 1201.
Do I need a licensed installer in Florida?
Yes. Florida law requires any person who installs a mobile home to hold a mobile home installer license from the Department of Highway Safety and Motor Vehicles, and setup includes leveling (Fla. Stat. 320.8249, 320.822(14)). The state rule adds that all installations must be done by a licensed installer, dealer installer or manufacturer installer (Fla. Admin. Code r. 15C-1.0102). Ask for the license number and verify it with FLHSMV.
What wind zone is my county in?
Check the data plate inside your home, then compare it to the county list. In Texas, Aransas, Brazoria, Calhoun, Cameron, Chambers, Galveston, Jefferson, Kenedy, Kleberg, Matagorda, Nueces, Orange, Refugio, San Patricio and Willacy are Wind Zone II and all others are Zone I (Tex. Occ. Code 1201.256). In Florida, Broward, Charlotte, Collier, Miami-Dade, Franklin, Gulf, Hendry, Lee, Martin, Manatee, Monroe, Palm Beach, Pinellas and Sarasota are Zone III and the rest are Zone II (24 CFR 3280.305).
Does homeowners insurance pay for re-leveling?
Usually not when the cause is gradual settling, soil movement or wear. The Texas Department of Insurance lists earth movement and wear and tear among risks most home policies do not cover. Sudden damage from a covered event, such as a windstorm that shifts the home, is a different question and depends on your policy. In Florida, windstorm coverage for manufactured homes is tied to installation under state rules (Fla. Stat. 320.8325(2)). Read your policy and ask your agent in writing.
What is the difference between a mobile home and a manufactured home?
In Texas law, a mobile home is a structure built before June 15, 1976, on a permanent chassis and designed as a dwelling (Tex. Occ. Code 1201.003(20)). A HUD-code manufactured home is built after that date to the federal construction standards in 24 CFR part 3280 and carries a HUD label. Both sit on piers and anchors unless placed on a permanent foundation, and both are covered by the state installer licensing rules on this page.
Can I put a manufactured home on a permanent foundation later?
Yes, with an engineered design. Federal standards allow foundation systems other than piers and footings when backed by engineering data, and require foundation plans to be designed and certified by a registered engineer or architect (24 CFR 3285.301). HUD's FHA rule describes a site-built permanent foundation, removal of the hitch and running gear, grade at or above the 100-year flood elevation, and a continuous foundation-type enclosure (24 CFR 203.43f). Get a permit and a sealed design before starting.
How long does a Texas installer's warranty last?
Texas requires the installer to give a written warranty that the installation meets state standards. Unless the warranty gives longer, the installer or retailer has no liability for a defect reported in writing more than two years after the later of the purchase date or installation date (Tex. Occ. Code 1201.361). If warranty service is refused, you can ask TDHCA for a free consumer complaint home inspection (1201.355).
Sources
- 24 CFR part 3285, Model Manufactured Home Installation Standards (eCFR)
- 24 CFR 3280.305, Structural design requirements and wind zones (eCFR)
- 24 CFR 203.43f, Eligibility of mortgages covering manufactured homes (eCFR)
- Texas Occupations Code ch. 1201, Texas Manufactured Housing Standards Act
- TDHCA Manufactured Housing Division
- Fla. Stat. 320.8249, Mobile home installers license (2025)
- Fla. Stat. 320.8325, Uniform installation standards (2025)
- Fla. Stat. 320.822, Definitions (setup or installation) (2025)
- Florida Administrative Code chapter 15C-1 (rules 15C-1.0101 to 15C-1.0109)
- FLHSMV: Dealers, Installers, Manufacturers, Distributors, and Importers
- Fla. Stat. 553.79, Permits (2025)
- Fla. Stat. 627.70132, Notice of property insurance claim (2025)
- 44 CFR 59.1, NFIP definitions: substantial damage and improvement (eCFR)
- 44 CFR 60.3, Floodplain management criteria (eCFR)
- 44 CFR part 61, Standard Flood Insurance Policy (eCFR)
- Texas Department of Insurance, Homeowners insurance guide
- Florida Geological Survey, Subsidence incident reports
- U.S. Drought Monitor state statistics, Texas, Nov. 17, 2026
- Bob Vila, Mobile Home Floor Repair Cost (updated Jan. 11, 2024)
- This Old House, Foundation Repair Cost (updated Oct. 8, 2026)
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


