New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Foundation repair contractors

Building a New Home on Expansive Clay: What Foundation Should It Have, and What Should You Ask Your Builder?

A buyer-side guide to foundation design on expansive clay in Texas and on Florida's soft and filled soils: what the geotechnical report should contain, how post-tensioned and structural slabs differ, what pad preparation really does, which inspections happen before the pour, and the questions to put to your builder in writing.

A new home on expansive clay should have a foundation designed by an engineer from a site-specific geotechnical report. The usual choices are a stiffened slab designed to the WRI/CRSI or PTI DC 10.5 methods the building code names, a structural slab carried on piers with void forms underneath, or a pier-and-beam floor. Before the pour, the steel or tendons, beams, vapor retarder and plumbing should be inspected, and the lot should be graded to drain away.

Key facts

  • The Florida Building Code requires slabs on expansive soils to be designed with WRI/CRSI Design of Slab-on-Ground Foundations (nonprestressed) or PTI DC 10.5 (post-tensioned), or by other rational methods open to peer review that consider both center lift and edge lift (FBC 1808.6.2).
  • Soil is classed as expansive when it has a plasticity index of 15 or more, more than 10 percent passing a No. 200 sieve, more than 10 percent finer than 5 micrometers, and an expansion index over 20; the expansion index test alone can suffice (FBC 1803.5.3).
  • A required geotechnical report must include boring logs, the soil profile, water table, foundation recommendations including provisions to mitigate expansive soils, and expected total and differential settlement (FBC 1803.6).
  • Instead of designing for expansive soil, the code allows removing it to a depth of constant moisture or stabilizing the active zone by chemical, dewatering, presaturation or equivalent methods (FBC 1808.6.3, 1808.6.4).
  • In Texas, the exemption from engineering licensure for private dwellings does not cover engineering design of a home slab on IRC-classified expansive soil unless the work meets the IRC as applied locally (Tex. Occ. Code 1001.056(c)(2)).
  • Ground next to a foundation must slope away at least 5 percent for 10 feet (FBC 1804.4); the residential code calls for 6 inches of fall in the first 10 feet (FBC Residential R401.3).
  • Florida's required foundation inspection covers stem walls, monolithic slabs, piling and pile caps, and footers and grade beams, and is made after trenches are dug and forms set (FBC 110.3).
  • Florida owners may hire a licensed private provider for plan review and inspections, with written notice to the building official and a permit fee reduction (Fla. Stat. 553.791).
  • Mud, organic silt, organic clays, peat and unprepared fill may not be assumed to have any presumptive load-bearing value without supporting data (FBC 1806.2).

What foundation should a new home on clay have?

There is no single right answer, which is why the law and the code push the decision to an engineer working from soil test data. The Florida Building Code, which applies statewide, gives a builder four paths on expansive soil (FBC 1808.6). Texas cities enforce the International Residential Code as they adopt it locally, and Texas engineering law ties slab design on expansive soil to that code. The four paths:

  1. Design the foundation to resist the movement. A stiffened slab-on-ground designed by an accepted method so it can ride the soil without damaging the house.
  2. Get below or isolate from the moving soil. Piers or piles that reach below the active zone, designed so the soil cannot lift them, with the floor isolated from the clay.
  3. Remove the expansive soil deep enough that the remaining soil has constant moisture, and replace it with non-expansive fill.
  4. Stabilize the soil in the active zone with chemical treatment, dewatering, presaturation or an equivalent technique.

The active zone is the depth of soil whose moisture changes with the seasons. Below it, moisture is steady and clay does not move much.

Foundation typeHow it handles clayQuestions to ask
Post-tensioned stiffened slabSteel tendons tightened after the concrete cures squeeze the slab; deep perimeter and interior beams stiffen itWhich PTI DC 10.5 edition was used? What edge and center lift values came from the geotech report?
Conventionally reinforced stiffened slabRebar and beams sized by the WRI/CRSI methodSame soil inputs; beam depth and spacing
Structural slab on piers with void formsSlab and beams span between drilled piers; cardboard void boxes leave a gap so swelling clay cannot push up the slabPier depth versus active zone; void depth; how the void forms are protected from water before the pour
Pier-and-beam (crawl space)Wood or steel floor framing on piers, with air space under the floorCrawl space ventilation and drainage, pier depth, access opening size

In Texas, the engineering board has heard concerns from North Texas engineers about repairs that put piers under ordinary slabs and turn them into suspended slabs they were not designed to be (TBPELS response #51, 2019). The lesson for new construction: if a slab will be supported on piers, it must be designed as a structural slab from the start. Compare foundation types on pier-and-beam vs. slab.

Should I get a geotechnical report before building?

Yes, and on expansive clay you usually do not get a choice. The Florida Building Code says that where expansive soil is likely, the building official "shall require soil tests" (FBC 1803.5.3). The residential code lets the building official decide whether to require a soil test where expansive, compressible or shifting soils are likely (FBC Residential R401.4). Texas law adds an engineering requirement: slab design on IRC-classified expansive soil falls outside the private-dwelling exemption from engineering licensure unless the work meets the IRC as locally applied (Occupations Code 1001.056(c)(2), added in 2009). A builder who says "we've built on this street for years, no soil test needed" is asking you to take a risk the code does not.

What a geotechnical report should contain

When a geotechnical investigation is required, FBC 1803.6 lists what the written report must include, at a minimum:

  • a plot showing where the borings or tests were done
  • complete boring and penetration test logs and sample records
  • the soil profile
  • the water table elevation, if found
  • foundation type and design recommendations, including bearing capacity, provisions to mitigate expansive soils, and ways to handle liquefaction, differential settlement and varying soil strength
  • expected total and differential settlement
  • deep foundation information, where piers or piles are used

The scope, including how many borings and which lab tests, is decided by a registered design professional (FBC 1803.3.1). One boring for a whole subdivision is not the same as borings on your lot. Ask how close the nearest boring was to your house footprint.

Reading the key numbers: PI and PVR

  • Plasticity index (PI) measures how much water clay can hold while staying plastic. Higher PI usually means more shrink-swell. The code treats soil as expansive when PI is 15 or more and other tests are met (ASTM D4318 method).
  • Expansion index (EI) is a lab swell test; an EI over 20 meets the code's expansive test, and the EI test alone can be used (ASTM D4829).
  • PVR (potential vertical rise) is a number, in inches, that Texas engineers often use to estimate how much the ground surface could heave if dry clay became wet. A higher PVR calls for a stiffer slab, deeper piers, soil treatment or a structural slab. Ask how the PVR was calculated, what depth of soil it assumes, and what moisture condition it starts from, because different assumptions give very different numbers.
  • Edge moisture variation distance and differential swell are inputs the PTI method uses to design for edge lift and center lift. Your engineer should be able to show you where they came from.

A geotechnical report costs $500 to $3,000, according to This Old House's 2026 cost guide (Angi data). On a new home, that is small compared with the cost of a foundation repair later.

What is a post-tensioned slab (PTI) design?

A post-tensioned slab has high-strength steel cables, called tendons, running through it in plastic sheathing. After the concrete hardens, a crew pulls each tendon tight with a hydraulic jack and locks it at the slab edge. That squeezes the concrete, which resists cracking and lets a slab act stiffer than its thickness suggests. Stiffening beams around the edge and across the interior add more stiffness.

The Post-Tensioning Institute (PTI) publishes the design standard the code names: PTI DC 10.5, for shallow post-tensioned foundations on expansive and stable soils. FBC 1808.6.2 says post-tensioned slabs on expansive soil shall be designed per PTI DC 10.5, and conventionally reinforced slabs per the WRI/CRSI Design of Slab-on-Ground Foundations. Alternative rational methods are allowed if they account for both center lift and edge lift and are open to peer review. The code text we reviewed names the standard without the edition year, so ask your engineer which edition was used and whether your local code references the same one.

Questions to ask about a post-tensioned design

  • What edge lift and center lift values did you design for, and where did they come from?
  • How deep and how far apart are the stiffening beams?
  • What is the tendon spacing and the effective prestress?
  • When will the tendons be stressed, and who records the elongations?
  • How will the tendon ends be protected from corrosion?

A warning that lasts the life of the house: never cut or core a post-tensioned slab without an engineer. A cut tendon can release violently and leaves part of the slab without prestress. Keep the as-built tendon drawings for future plumbing and remodel work.

Should my builder use piers under the slab, and what are void boxes?

Piers help when the active zone is deep or the expected heave is large. But piers under a normal slab-on-ground are not automatically better. If clay swells, it can lift a slab off the tops of piers or push up a slab that is not separated from the soil. That is why a pier-supported design usually comes with a structural slab, designed to span between piers like a floor, and with void forms underneath.

Void forms, often called void boxes or carton forms, are cardboard or similar boxes placed on the ground before the pour. The concrete is poured on top. Over time the cardboard softens and decays, leaving a gap between the slab and the clay. When the clay swells, it fills the gap instead of lifting the house. For this to work, the forms must stay dry and intact until the pour, the depth of the void must match the expected heave, and the piers must be deep enough and designed to resist uplift. FBC 1808.6.1 says foundations penetrating expansive soil must be designed to resist the forces from soil volume change or be isolated from it, and to prevent uplift.

Ask: How deep are the piers compared with the active zone? Are they reinforced full length? What is the void depth, and how will forms be protected from rain before the pour? Who inspects the piers before concrete goes in? See drilled and bell-bottom piers.

What pad preparation should be done?

"Pad prep" is the work on the soil before forms go up. Builders advertise many approaches; here is what the code supports and what to verify.

ApproachWhat it isWhat the code saysWhat to ask
Select fillRemoving some clay and replacing it with low-swell imported fillRemoval must go deep enough to leave soil with constant moisture, and fill must not contain expansive soil (FBC 1808.6.3)How deep was clay removed, and how does that compare with the active zone in the geotech report?
Moisture conditioning or presaturationWetting the clay before building so it swells firstPresaturation is a recognized stabilization method (FBC 1808.6.4)To what depth and moisture target? How is it tested? What keeps it from drying out before the pour?
Chemical stabilizationMixing or injecting chemicals such as lime into the clayChemical stabilization is allowed (FBC 1808.6.4)Which chemical, depth, and test results? Who designed it?
Compacted fillFill placed in layers and compactedFill under shallow foundations must follow an approved geotech report, except fill 12 inches deep or less compacted to at least 90 percent of max dry density per ASTM D1557 (FBC 1804.6)Ask for compaction test reports with locations and depths

The honest answer to "does pad prep prevent foundation problems?" is that it helps when it is designed from the soil data and tested. It is not a substitute for a foundation designed for the expected movement. Any builder claim like "our pad prep eliminates movement" should come with the engineer's design basis and test reports. If they cannot produce them, treat the claim as marketing.

Florida: muck, organic soil and fill

In Florida the bigger risk is usually soft or organic soil, not swelling clay. FBC 1806.2 says mud, organic silt, organic clays, peat or unprepared fill may not be assumed to have any presumptive load-bearing capacity without supporting data. FGS lists compressing organic layers, decaying stumps and debris, and improperly compacted soil among common causes of ground subsidence. On a Florida lot, ask whether organic soil (muck) was found and fully removed, what replaced it, and for the compaction test results under the footings. See our Florida guide.

Drainage plans and lot grading

Water is the trigger for clay movement and for washing out sand. The code sets minimums:

  • The ground next to a foundation must slope away at least 5 percent (1 unit vertical in 20 horizontal) for at least 10 feet. If lot lines prevent that, a 5 percent slope must lead to another approved way of carrying water away. Swales within 10 feet of the building must slope at least 2 percent, and paved surfaces within 10 feet must slope at least 2 percent away (FBC 1804.4).
  • The residential code calls for the grade to fall at least 6 inches within the first 10 feet, with drains or swales where lot lines or walls prevent that (FBC Residential R401.3).

The ASCE Texas Section's foundation guidelines recommend the same 5 percent slope for the first 10 feet where practicable, plus swales of at least 2 percent if practicable and 1 percent minimum. Ask for the lot grading plan, gutter and downspout locations, and where downspouts will discharge. Watch for the most common failure after move-in: landscaping beds and edging that block the slope the builder created. See drainage, gutters and grading.

What inspections happen before a slab is poured?

The building department inspects the foundation before concrete. In Florida, FBC 110.3 requires a foundation inspection after trenches are excavated and forms erected, covering stem walls, monolithic slabs-on-grade, piling and pile caps, and footers and grade beams. In flood hazard areas, an elevation certificate must be submitted when the lowest floor is placed and before further vertical construction. Texas cities run similar inspections under the residential code they adopt.

Pre-pour checklist

A city inspection is a code minimum. This list is what a careful owner or third-party inspector looks at against the engineer's sealed foundation plan:

  • Beams: depth, width and location match the plan; trenches clean, without loose soil or standing water.
  • Tendons (post-tensioned): spacing and count match the plan; tendons supported on chairs at the right height; anchors and pocket formers installed at edges; sheathing not torn.
  • Rebar (conventional or beams): bar size, spacing, laps and concrete cover per plan, held up on chairs rather than lying on the ground.
  • Vapor retarder: continuous, laps taped, punctures and penetrations sealed.
  • Plumbing: drain and supply lines tested before the pour, with sleeves where pipes pass through beams so movement does not shear them.
  • Piers and void forms (if specified): pier depth and steel verified; void boxes dry, undamaged and at the specified depth.
  • Pad: compaction or moisture test reports on file.

After the pour, ask for the concrete delivery tickets and any cylinder strength results, and for post-tensioned slabs, the stressing record showing each tendon's elongation.

Can I hire my own third-party inspector or engineer for the slab pour?

Usually yes, but check your contract first. Some builder contracts limit site access, so ask before you sign and get the right to inspect in writing, with notice of pour dates.

  • Texas: Some cities use third-party inspection. Fort Worth's residential permit application, for example, asks whether third-party inspections or plan review are used. Separately, you can hire a licensed engineer to review the plan and observe before the pour. Only a licensed engineer may give an engineering opinion; TREC inspectors who are not engineers cannot evaluate engineering design (TBPELS Advisory #43).
  • Florida: Fla. Stat. 553.791 lets an owner, or the contractor with written authorization, hire a private provider for plan review, required inspections or both. Providers must be licensed building code administrators, engineers or architects, may not inspect a building they designed or built, and written notice goes to the building official at permit application or by 2 p.m. two business days before the first inspection. The local government must reduce the permit fee by its cost savings. This is the formal path; you can also hire your own engineer to observe as an extra check.

A third-party engineer pre-pour inspection means a licensed engineer, ideally one not employed by the builder, visits after forms, steel and plumbing are in place and compares them with the sealed plan. They send a short report or letter, and the builder fixes issues before concrete. Ask for photos of beams, steel and tendon layouts with the report. See what engineers inspect.

Stem wall or monolithic slab in Florida flood zones

A monolithic slab pours the slab and its thickened edge footing at once. A stem wall foundation uses a footing and a short concrete or block wall, with the slab inside on compacted fill, so the floor can sit higher. In flood zones, height matters: in Zones A1-30, AE and AH, new homes must have the lowest floor at or above the base flood elevation, and in V zones, new homes must be elevated on pilings or columns with the lowest horizontal structural member at or above base flood level and an engineer or architect involved in the design (44 CFR 60.3). Florida's foundation inspection list names stem walls, monolithic slabs and piling separately (FBC 110.3), and FBC chapter 18 has High-Velocity Hurricane Zone sections on slabs on fill, monolithic footings and piles. Ask your designer which type the flood elevation and soil report call for.

Warranties and your rights if the slab fails

Get the builder's written warranty and read what it covers for the foundation, for how long, and whether it transfers. Separately, both states give you legal procedures:

  • Texas: The Residential Construction Liability Act (Property Code ch. 27) requires written notice by certified mail at least 60 days before suing and lets the builder inspect and offer to repair. Most suits must be filed within 10 years of substantial completion (CPRC 16.009). See slab defects and the RCLA.
  • Florida: Chapter 558 requires written notice at least 60 days before suing, and the statute of repose for design and construction claims is 7 years after the certificate of occupancy or completion (Fla. Stat. 95.11(3)(b), cut from 10 years in 2023). See Chapter 558 defects.

Keep the geotech report, sealed foundation plan, inspection records, compaction tests, tendon stressing records and photos. They are your best evidence later, and the first thing a buyer's engineer will ask for. This is general information, not legal advice; talk to a construction attorney about a specific dispute.

How to choose a provider

  • Ask for the site-specific geotechnical report before signing, and read the PI, PVR or swell values and foundation recommendations.
  • Ask which design method was used: PTI DC 10.5 (and edition), WRI/CRSI, or a structural slab on piers.
  • Confirm the foundation plan is sealed by a licensed engineer.
  • Get the pad preparation plan in writing with depths and test requirements.
  • Write the right to inspect before the pour into your contract, with notice of pour dates.
  • Hire your own engineer (Texas) or a private provider or engineer (Florida) for a pre-pour inspection.
  • Check beams, tendons or rebar, vapor retarder, plumbing tests and sleeves against the plan.
  • Collect compaction tests, concrete tickets and tendon stressing records.
  • Confirm the lot grading plan gives 6 inches of fall in the first 10 feet and downspouts discharge away.
  • In Florida flood zones, confirm the lowest floor elevation and get the elevation certificate.
  • Store all documents for warranty claims and resale.

Related foundation repair contractors guides

Foundation repair contractors by state and city

Questions people ask

Is a post-tensioned slab better than a conventional slab on clay?

Neither is automatically better. The building code accepts both: post-tensioned slabs designed to PTI DC 10.5 and conventionally reinforced slabs designed to the WRI/CRSI method, as well as other rational methods that account for center lift and edge lift. What matters is that an engineer designed the slab from soil data for your lot and that it was built as drawn. Ask to see the design inputs.

What PVR is too high to build a normal slab?

There is no single statewide cutoff in the code text we reviewed. PVR is an estimate of possible heave, and engineers choose stiffer slabs, deeper piers, soil treatment or structural slabs as it rises. Ask your engineer what PVR the design assumes, how it was calculated, and why the chosen foundation is suitable for that number. If the answer is vague, get a second opinion.

Does Texas require an engineer to design my new home's slab?

For slabs on expansive soil, generally yes. Texas Occupations Code 1001.056 exempts people designing private dwellings from engineering licensure, but subsection (c)(2), added in 2009, says the exemption does not apply to engineering design of a residential slab on soil classified as expansive under the International Residential Code as applied locally, unless the work meets those IRC requirements. Ask your city what it requires.

Can I skip the soil test if neighbors' homes are fine?

Not safely, and often not legally. The Florida Building Code says that where expansive soil is likely, the building official shall require soil tests, though the official may waive a geotechnical investigation if satisfactory data from adjacent areas shows it is unnecessary. Soil can change across short distances, and a report for your footprint costs $500 to $3,000 per This Old House's 2026 guide.

What should a pre-pour inspection cost and who does it?

We found no verified current price for a stand-alone pre-pour inspection. This Old House's 2026 guide lists a structural engineer report at $500 to $1,000, which is a reasonable reference point. A licensed engineer should do it in Texas because evaluating engineering design is engineering. In Florida, a licensed private provider under 553.791 can perform required inspections, and you can still hire your own engineer.

Do void boxes always go under a structural slab?

They are common under structural slabs on expansive clay because they create a gap so swelling soil cannot push up the slab. Whether you need them, and how deep, depends on the expected heave in the geotechnical report. They only work if they stay dry and intact until the pour. Ask how the forms will be protected and who checks them before concrete arrives.

How should a Florida lot with muck be prepared?

Florida's code says organic soils, peat and unprepared fill cannot be assumed to carry any load without supporting data. A geotechnical report should say how deep organic material goes and how to handle it, often by removing it and replacing it with compacted fill tested under an approved report. Ask for the boring logs and compaction tests under your footings.

Can my builder refuse to let my inspector on site?

Your rights depend largely on your contract, so negotiate access before you sign. Ask for written notice of the foundation inspection and pour dates and the right to have your engineer or inspector present. In Florida, the private provider law gives owners a formal route to hire their own licensed provider for required inspections, with notice to the building official.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration