New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Plumbing

How Do I Fix a Dripping Faucet, Low Shower Pressure or a Shower That Runs Hot and Cold?

How to identify your faucet type, replace the right washer or cartridge, clean mineral scale from aerators and showerheads, and know when a dripping fixture is your landlord's job in Texas or Florida.

A dripping faucet almost always means a worn rubber washer, O-ring, seat or cartridge. Shut off the valves under the sink, plug the drain, take the handle off and identify the faucet type: compression, cartridge, ball or ceramic disc. Then replace the worn part with an exact match from the same brand. EPA says one drip per second wastes more than 3,000 gallons a year, so fix it soon.

Key facts

  • A faucet dripping once per second wastes more than 3,000 gallons a year, enough for more than 180 showers (EPA WaterSense).
  • A showerhead leaking 10 drips per minute wastes more than 500 gallons a year (EPA WaterSense).
  • The average household's leaks waste more than 9,300 gallons a year, and fixing easy leaks can save about 10 percent on water bills (EPA WaterSense).
  • WaterSense bathroom faucets and aerators use no more than 1.5 gallons per minute, compared with the 2.2 gpm standard (EPA WaterSense).
  • Standard showerheads use 2.5 gpm; WaterSense showerheads use no more than 2.0 gpm and must pass spray force and coverage tests (EPA WaterSense).
  • USGS classifies water above 180 mg/L of hardness as very hard; heated hard water forms scale that can clog pipes and fixtures.
  • Austin Water offers customers free 1.5 gpm showerheads and 1.5 gpm kitchen and 0.5 gpm bathroom faucet aerators through its Conservation Hub.
  • Texas Occupations Code 1301.551 lets cities exempt repairing leaks and replacing lavatory and kitchen faucets from plumbing permits.

Why do faucets drip?

Every faucet has a part that opens and closes the water path. Over time, that part wears out, gets scratched by grit, or gets crusted with minerals. Water then seeps past it and drips from the spout. EPA says old and worn faucet washers and gaskets frequently cause leaks.

Where the water shows up tells you which part failed:

Where you see waterLikely cause
Drips from the spout when offWorn washer, seat, cartridge or disc seals
Water around the handle baseWorn O-ring or packing on the stem or cartridge
Water around the spout base (kitchen swivel spouts)Worn spout O-rings
Water under the sinkSupply line, shutoff valve or faucet base seal, not the cartridge. See under-sink leaks.
Drip only from the tub spout while showeringWorn diverter
Drip from showerhead after shutting offA few seconds of drip is normal draining; a steady drip means the shower valve cartridge is worn

A drip is not trivial. EPA's Fix a Leak Week data says a faucet dripping once a second wastes more than 3,000 gallons a year. If it is the hot side, you are paying to heat that water too.

What type of faucet do I have?

There are four main designs. You need to know which one you have before buying parts.

TypeHow to recognize itPart that wears
CompressionTwo handles that you twist several turns and tighten to stop the water. Common in older homes.Rubber washer on the stem, and the brass seat
CartridgeOne or two handles that move smoothly, often a quarter or half turn, or a single lever that lifts and swivelsPlastic or brass cartridge with O-rings
BallSingle lever over a rounded cap on top of the faucet body, mostly kitchen faucetsRubber seats, springs and O-rings around a metal or plastic ball
Ceramic discSingle lever over a wide cylinder body; very smooth movementRubber seals under the discs; the discs rarely wear

If you are not sure, the brand helps. Look for a logo on the handle, the spout or the escutcheon (the cover plate on the wall or deck). Major brands publish parts diagrams by model number, and Moen, for example, offers an online faucet identifier where you upload a photo to find the model and replacement parts. When in doubt, take the old cartridge to a plumbing supply store. Cartridges that look alike often differ in length, spline count (the teeth on the stem) or hot and cold rotation.

How do I fix a dripping faucet, step by step?

Before you start

  • Turn off both shutoff valves under the sink by turning clockwise. If there are none, or they will not close, shut off the main water valve. Then open the faucet to drain the line.
  • Close the drain stopper or lay a rag in the sink so small screws do not disappear.
  • Lay parts out in order on a towel and take phone photos as you go.
  • Tools: screwdrivers, an adjustable wrench, hex keys, needle-nose pliers, plumber's grease (silicone, safe for potable water) and white vinegar.

Compression faucet

  1. Pry off the decorative cap and remove the handle screw and handle.
  2. Unscrew the packing nut and the stem with a wrench.
  3. Remove the screw at the bottom of the stem and replace the rubber washer with an exact size. Replace the O-ring or packing on the stem too.
  4. Look into the faucet body at the brass seat. If it is pitted, a seat wrench removes a replaceable seat, or a seat-dressing tool smooths it. A pitted seat chews up new washers in weeks.
  5. Reassemble and do not overtighten the handle. Overtightening is what wears compression washers fast.

Cartridge faucet

  1. Remove the handle. Look for a screw under a cap or a small hex setscrew on the side or back.
  2. Remove the retaining clip or nut that holds the cartridge. Many single-handle cartridges use a U-shaped brass clip you pull straight up with pliers.
  3. Pull the cartridge straight out. Old cartridges can stick; manufacturers sell or include a plastic puller. Note which way the stem faces.
  4. Match the new cartridge to the old one, grease the O-rings lightly and install it in the same orientation. If hot and cold are reversed after reassembly, rotate the stem 180 degrees.

Ball faucet

  1. Remove the handle and the cap.
  2. Lift out the cam and the ball.
  3. Use a small screwdriver to pull out the two rubber seats and springs from inside the body.
  4. Install a full repair kit: new seats, springs and O-rings. Replace the ball if it is scratched.

Ceramic disc faucet

  1. Remove the handle and the decorative cap.
  2. Unscrew the disc cylinder mounting screws and lift out the cylinder.
  3. Replace the rubber seals on the bottom of the cylinder. Clean the inlet holes with vinegar if scaled.
  4. Turn water on slowly with the handle open, because a pressure surge can crack ceramic discs.

After any repair, open the shutoffs slowly with the faucet open, let air and debris flush out, then remove and rinse the aerator.

Should I repair or replace my faucet?

Repair if parts are available and the faucet body is sound. Replace if:

  • The body is cracked or corroded, or water leaks from the base.
  • The brand or model is unknown and no matching cartridge can be found.
  • You have replaced the same part more than once in a short time, which points to a damaged body or seat.
  • You want a lower-flow faucet anyway. EPA says replacing old faucets and aerators with WaterSense models can save the average family 700 gallons a year.
  • The faucet is decades old and you also have lead concerns. See lead service lines and lead in plumbing.

Cost guidance: washers and O-ring kits are among the cheapest parts in a hardware store, and brand cartridges cost more, so price yours by model number. Fixr's 2026 toilet installation guide lists plumber rates of $75 to $150 an hour, and many plumbers charge a minimum trip charge. A single faucet repair is often under an hour of labor once the part is in hand. Ask for a flat quote that includes the part.

Texas Occupations Code 1301.551 lets cities exempt repairing leaks and replacing lavatory and kitchen faucets from permits. In Florida, Jacksonville exempts fixture replacement after the stop valve, and Miami-Dade lets licensed plumbing contractors repair or replace faucets without a permit.

Why is my shower pressure low but the sink is fine?

When only one fixture is weak, the cause is almost always at that fixture, not the house supply. Check in this order:

  1. The showerhead. Unscrew it and run the shower without it for a few seconds. If flow is strong without the head, the head is clogged or has a flow restrictor.
  2. Mineral scale. Hard water leaves calcium deposits in the small nozzles. See the cleaning steps below.
  3. The flow rate. A 1.5 or 1.8 gpm head feels weaker than a 2.5 gpm head. Standard showerheads use 2.5 gpm, and EPA says WaterSense heads use no more than 2.0 gpm but must pass tests for spray force, coverage and minimum flow across a range of household pressures. If a low-flow head feels weak, try a different WaterSense model before removing restrictors.
  4. The shower valve cartridge. A clogged or failing cartridge restricts both hot and cold. Debris often lodges here after a water main repair or a water heater replacement.
  5. Hot side only weak? Look at the water heater shutoff valve, sediment in the heater, or a failing mixing valve.
  6. Old galvanized pipe can rust shut from the inside. If both hot and cold are weak in a bathroom and your home was built before the 1960s, read galvanized pipe.

If every fixture is weak, the issue is house-wide. See water pressure problems.

How do I clean a clogged aerator or showerhead?

Hard water is water carrying dissolved calcium and magnesium. USGS classifies 0 to 60 mg/L as soft, 61 to 120 as moderately hard, 121 to 180 as hard and above 180 as very hard. USGS notes that heated hard water forms scale that can clog pipes and shorten equipment life. Your water utility's annual water quality report, often called the Consumer Confidence Report, lists your hardness. Homes on private wells should test.

Faucet aerator

  1. Unscrew the aerator from the spout tip by hand, or with pliers wrapped in tape. Some newer faucets use a hidden aerator that needs a small plastic key.
  2. Take it apart in order: screen, flow restrictor, washer.
  3. Soak in white vinegar for one to several hours. Brush with an old toothbrush and rinse.
  4. Replace it if parts are cracked. A WaterSense aerator rated 1.5 gpm costs a few dollars.

Showerhead

  1. Remove the head, or tie a plastic bag of vinegar around it so the face is submerged.
  2. Soak overnight for heavy scale.
  3. Rub rubber nozzles with your thumb to pop scale loose, and clean the inlet screen.
  4. When you reinstall, EPA suggests wrapping the arm threads with pipe tape and checking or replacing the washer or O-ring inside the head.

If you clean aerators every few months, consider whether a water softener or point-of-use filter makes sense. See hard water and softeners.

Why does my shower suddenly turn hot or cold?

A sudden temperature swing when someone flushes or starts the washer means the shower valve cannot keep up with a pressure change in the hot or cold line. The fix depends on the type of valve.

Valve typeHow it worksCommon problems
Pressure-balanceA spool or diaphragm inside the cartridge reacts to changes in hot or cold pressure and cuts the other side to keep the mix steady. One handle usually controls both flow and temperature.Spool sticks from scale, causing swings, weak flow or water that will not get hot. Usually fixed by cleaning or replacing the cartridge.
ThermostaticA temperature-sensing element holds the outlet temperature you set. Often has a separate volume control.Sensing element clogs or wears; costs more to repair; reacts well to both pressure and temperature changes.
Older two- or three-handle valvesNo automatic balancing.Big swings and scald risk. Consider upgrading during a remodel.

Other causes of hot and cold swings:

  • Anti-scald limit stop set wrong. Many single-handle valves have a plastic limit stop under the handle that caps how far you can turn to hot. If the shower never gets hot enough, a plumber or the maker's instructions can adjust it.
  • Water heater problems. If the shower runs hot then cold during a long shower, the heater may be undersized, have sediment, or a failed dip tube or element. See no hot water.
  • Tankless heater minimum flow. A low-flow showerhead plus a cold-side mix can drop below a tankless unit's minimum flow and cause cold bursts.

Scald safety matters, especially with young children or older adults. Set water heaters at a safe temperature and use a valve with working anti-scald protection.

How do I replace a shower valve cartridge?

  1. Find the brand and model. It may be on the handle, the trim plate or the valve body behind it. Take photos of the trim.
  2. Shut off water. Many shower valves have built-in stops (small screw slots on each side of the cartridge). If not, shut off the main.
  3. Remove the handle, then the trim plate (escutcheon).
  4. Remove the retaining clip or bonnet nut. Note the cartridge's orientation; many have a "hot" mark.
  5. Pull the cartridge. Old ones can be stuck tight; use the brand's puller to avoid damaging the valve body.
  6. Install the new cartridge with lightly greased O-rings in the same orientation, reinstall the clip and check the hot and cold direction before reinstalling trim.
  7. Reset the anti-scald limit stop per the instructions.

Call a plumber if the valve body is leaking inside the wall, the brand is discontinued, or the cartridge will not come out. Replacing a valve body means opening the wall, and in many cities it needs a permit.

What is a WaterSense faucet or showerhead, and is it worth it?

WaterSense is EPA's label for products independently certified to use at least 20 percent less water and to perform as well as or better than standard models.

FixtureStandard flowWaterSense maximum
Bathroom faucet or aerator2.2 gpm1.5 gpm
Showerhead2.5 gpm2.0 gpm

EPA says replacing old faucets and aerators can save the average family 700 gallons a year, and that a WaterSense aerator can cost as little as a few dollars. Showering is nearly 17 percent of residential indoor water use, so a showerhead swap is one of the cheapest savings in the house, and it also cuts water heating energy.

Free and discounted fixtures: Austin Water customers can get free 1.5 gpm showerheads and aerators through its Conservation Hub. Other Texas and Florida utilities run similar programs from time to time; check your water utility's conservation page.

Does a landlord have to fix a dripping faucet?

Texas. Texas Property Code 92.052 requires a landlord to make a diligent effort to repair conditions that materially affect the physical health or safety of an ordinary tenant, after notice from a tenant who is current on rent. A slow drip may not meet that bar by itself. A faucet that will not shut off, no hot water at 120 degrees from a landlord-supplied heater, or a leak causing mold or damage is more likely to qualify. Many Texas leases also promise repairs beyond what the statute requires. If your lease is written and says repair requests must be in writing, send them in writing.

Florida. Florida Statute 83.51 requires landlords to keep plumbing in reasonable working condition where no local code applies, and in apartments and other units that are not single-family homes or duplexes, to provide running water and hot water unless the lease says otherwise in writing. For single-family homes and duplexes, those duties can be changed in writing. Section 83.51(4) excludes damage the tenant caused.

Tip for both states: report drips in writing with a photo and date. Small leaks get worse, and a written record protects your deposit. See Texas and Florida landlord repair guides.

Other fixture leaks worth fixing now

  • Tub spout diverter. If water pours from the tub spout while the shower runs, the diverter gate is worn. Many slip-on or threaded spouts are replaced whole.
  • Showerhead connection. EPA says some leaky showerheads can be fixed by tightening the connection and using pipe tape on the arm.
  • Outdoor hose bibs. A dripping spigot has a washer or cartridge just like an indoor faucet. Frost-free sillcocks in Texas often fail after a hard freeze. See outdoor plumbing.
  • Pull-down kitchen sprayer hoses can leak under the sink at the quick-connect. Check the cabinet floor for water.

To find hidden drips, EPA suggests reading your water meter before and after two hours when no water is used. If it moves, look for a leak. See high water bill.

How to choose a provider

  • Shut off the valves under the sink before opening a faucet.
  • Photograph each step of disassembly.
  • Identify the faucet type and brand before buying parts.
  • Take the old cartridge or washer to the store to match it.
  • Use silicone plumber's grease on O-rings.
  • Turn water back on slowly with the faucet open.
  • Soak aerators and showerheads in vinegar every few months in hard water.
  • Check your utility's water quality report for hardness.
  • Look for the WaterSense label on new faucets and showerheads.
  • Renters: report drips in writing with a dated photo.

Related plumbing guides

Plumbing by state and city

Questions people ask

How much water does a dripping faucet waste?

EPA says a faucet dripping once per second wastes more than 3,000 gallons a year, about the water needed for more than 180 showers. A showerhead leaking 10 drips per minute wastes more than 500 gallons a year. EPA also says the average home's leaks add up to more than 9,300 gallons a year, and fixing easy leaks can save about 10 percent on water bills.

Why does my faucet still drip after I replaced the washer?

On a compression faucet, a pitted brass seat will cut a new washer quickly, so the seat needs to be replaced or dressed. On cartridge faucets, a wrong-size cartridge, a missing O-ring or debris on the seat can keep it leaking. Turn water on slowly after repairs, because sediment that comes through can lodge in the new part.

How do I find out which cartridge my faucet uses?

Look for the brand on the handle, spout or trim plate, then check the maker's parts diagrams by model number. Some brands offer photo-based identifiers online. The most reliable way is to remove the old cartridge and take it to a plumbing supply store, because cartridges that look alike can differ in length, spline count or rotation.

Is it OK to remove the flow restrictor from my showerhead?

It may increase flow, but it also raises water and water heating use and can void the product's certification. If the shower is weak, first clean the head and inlet screen and check the valve cartridge. If you want more spray force at low flow, try a different WaterSense model, which must pass spray force and coverage tests.

Why is there water coming out of my faucet handle?

Water at the handle base means a worn O-ring or packing on the stem or cartridge, not the part that seals the spout. Replace the O-rings, or the whole cartridge if they are built in. On a compression faucet, tightening the packing nut a small amount can stop a handle leak temporarily.

Can hard water damage my faucets?

Yes. USGS says heated hard water forms scale that can clog pipes and shorten equipment life. In faucets, scale grinds O-rings, sticks cartridges and pressure-balance spools, and plugs aerators. Regular vinegar cleaning helps. If you replace cartridges often, test your hardness and consider a softener or filter.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration