Local Guide · Plumbing
How Do I Know If I Have Lead Pipes? Checking Your Service Line in Texas and Florida
Every water utility now has to tell you what your service line is made of, and most lead lines must be replaced by 2037. Here is how to check your own pipe, read the inventory, test your water and protect your family.
Look up your address on your water utility's service line inventory, which every community water system had to build by October 16, 2024. Then check the pipe where it enters your house: lead is dull gray, scratches to shiny silver, and a magnet will not stick. If your line is lead, galvanized requiring replacement, or unknown, use cold water and a filter certified to reduce lead, test your water through a certified lab, and ask your utility when it will replace the line.
Key facts
- In homes with lead service lines, those lines are typically the most significant source of lead in tap water (EPA).
- Initial service line inventories were due October 16, 2024 in Texas (to TCEQ) and Florida (to DEP or approved county health departments).
- Utilities must notify customers with lead, galvanized-requiring-replacement, or unknown lines within 30 days of the inventory, then every year.
- EPA's November 2025 update estimates 4 million lead service lines nationwide, down from a 2023 projection of 9.2 million.
- The final Lead and Copper Rule Improvements take effect November 1, 2027, lowering the lead action level from 15 ppb to 10 ppb.
- Florida DEP's schedule calls for full replacement of lead and GRR service lines by November 1, 2037.
- Congress banned non-lead-free plumbing for drinking water in 1986; a 2011 law cut the pipe and fixture limit from 8 percent to 0.25 percent.
- Certified lab lead tests cost about $15 to $100 (EPA); boiling water does not remove lead.
- The Infrastructure Investment and Jobs Act set aside $15 billion for utility lead service line replacement through state revolving funds.
What is a lead service line, and why does it matter most?
A service line is the pipe that carries water from the water main under the street to your building. It usually has two parts. The utility owns the part from the main to the meter. You own the part from the meter to your house. In San Antonio, for example, SAWS says it owns the water lateral from the main to the meter, and the customer owns the service line from the meter to the building. Miami-Dade Water and Sewer (WASD) says the same thing in plain terms: it did not install the pipe between your meter and your home, that section is private, and the county cannot access it.
Why the service line matters: EPA says that in homes with lead service lines, those pipes are typically the most significant source of lead in the water. Among homes without a lead service line, the most common problems are brass or chrome-plated brass faucets and plumbing joined with lead solder. Lead pipes are more likely in older cities and in homes built before 1986.
Lead gets into water through corrosion. Water that is more acidic or low in minerals dissolves metal faster. EPA lists the factors that change how much lead ends up in your glass: the water's chemistry, how much lead the water touches, water temperature, wear in the pipes, how long water sits in the pipes, and whether protective scale has formed inside them. That last point explains why digging or street work near an old lead line can cause a spike: shaking the pipe can knock that scale loose.
Lead, galvanized and "unknown": the three labels you will see
Utility inventories sort every line into categories. You will see these words on maps and in letters:
| Label | What it means | What to do |
|---|---|---|
| Lead | Pipe made of lead on either side of the meter. | Use a certified filter or flushing now; ask the utility about its replacement schedule. |
| Galvanized requiring replacement (GRR) | Galvanized iron or steel pipe on the customer side that is or was downstream of lead, or where the upstream material is unknown. Lead particles can stick inside galvanized pipe. | Treat it like lead. EPA counts GRR lines as lead service lines. |
| Unknown | The utility has no record of the material. | Check the pipe yourself and report it, or ask for a free utility inspection if offered. |
| Non-lead | Copper, plastic, or galvanized that was never downstream of lead. | Lead can still come from old solder or faucets; testing is the only proof. |
SAWS spells out the GRR rule clearly: galvanized pipe needs replacing only if it is on the customer side and lead was ever present on the SAWS side, or if the original upstream material is unknown. Other galvanized pipe is counted as non-lead.
How do I know if my water service line is lead?
There are three ways to find out, from easiest to most certain.
- Look up your address on your utility's service line inventory. Every community water system had to build one by October 16, 2024 and make it publicly accessible. Many utilities offer a searchable map.
- Check the pipe where it enters your house. EPA's online guide, Protect Your Tap: A Quick Check for Lead, walks you through this with a coin (a penny or key) and a magnet. Find the pipe coming into the house, usually near the main shutoff valve, in a garage, utility closet, or where the line rises from the slab, or at the meter box.
- Ask a licensed plumber to identify the material, or accept a utility inspection if your utility offers one. SAWS, for example, offers free inspections to eligible customers listed as "unknown".
The scratch and magnet check
The test uses the fact that lead is soft and not magnetic. Gently scratch the outside of the pipe with the edge of a coin or key, on a section before the shutoff valve. Then hold a magnet against it.
| What you see | Likely material |
|---|---|
| Dull gray pipe that scratches easily to a shiny silver color; magnet does not stick | Lead |
| Gray pipe that does not scratch shiny; magnet sticks; threaded joints | Galvanized steel |
| Penny-colored metal when scratched; magnet does not stick | Copper |
| White, black, blue, red or gray plastic | Plastic (PVC, CPVC, PEX, polyethylene, or polybutylene) |
Do not scratch hard or use a file. A damaged lead pipe can leak or release particles. Also check the whole run you can see: a home can have copper at the wall and lead under the yard. If you are in a slab-on-grade home in Texas or Florida, the pipe often rises out of the concrete or comes up beside the foundation, so only a short piece is visible. That is enough for the test.
One limit: the check tells you about the pipe you can see. EPA is clear that testing your drinking water is the only way to confirm if lead is present, because lead can also come from faucets and old solder.
For help telling plastic pipe types apart, see our visual pipe identification guide, and for galvanized lines see galvanized pipe: rust, pressure and lead risk.
What is the lead service line inventory, and where can I see it?
The inventory is a list of every service line in a water system and its material. It comes from EPA's 2021 Lead and Copper Rule Revisions (LCRR). Key dates:
- October 16, 2024: initial inventory due. In Texas it went to TCEQ; in Florida, to the DEP district office or an approved county health department, using EPA's template.
- Within 30 days of the inventory: the utility must notify customers whose lines are lead, GRR or unknown. TCEQ and Florida DEP both state this 30-day rule.
- Every year after: repeat notices until the line is no longer lead, GRR or unknown. Florida DEP lists repeat notifications by December 31, 2025 and every December 31 after, plus a July 1 certification to the state that notices went out.
- November 1, 2027: a fuller "baseline inventory" (including connectors) and a service line replacement plan are due under the newer rule. TCEQ says its baseline inventory template is expected in its SWIFT Submittals portal around November 2026.
Where to look in Texas and Florida's big cities
| City | Utility | What we confirmed |
|---|---|---|
| San Antonio | SAWS | Water Service Line Inventory Map at inventory.saws.org; categories lead, GRR, unknown, non-lead; free inspections for eligible "unknown" properties; self-report form; customer service 210-704-7297. |
| Miami and most of Miami-Dade | WASD "Know Your Pipes" | Inventory map on the program page; a gray dot means the material is unknown; a self-report survey with an option to ask for help; WASD says there are currently no known lead pipes in its system; phone 305-665-7477. |
| Houston, Dallas, Austin | Houston Public Works, Dallas Water Utilities, Austin Water | All are community water systems covered by the same inventory and notice rules. Check each utility's website or your water bill for its service line lookup. |
| Tampa, Orlando, Jacksonville | Tampa Water Department, OUC, JEA | Same federal and Florida DEP requirements apply. Look for "service line inventory" on the utility site or call customer service. |
Note that some cities inside a county run their own water systems. In Miami-Dade, for example, several municipalities keep separate inventories. Your water bill shows which utility serves you.
If you think the inventory is wrong, say so. Under the newer federal rule, systems must certify each year that they offered to inspect lines for customers who, within 30 days of the notice, said the inventory got their material wrong. That requirement appears in Florida DEP's schedule starting January 30, 2029.
Does my city have lead service lines? What the national numbers say
Fewer than first feared, but still millions. EPA's November 2025 update to its national needs survey, built for the first time on the actual LCRR inventories, estimates 4 million lead service lines nationwide: about 3 million reported as lead and about 1 million "unknown" lines predicted to be lead. EPA counts GRR lines in that total.
Older estimates are now out of date. EPA's 2023 survey had projected about 9.2 million lead lines nationally, and it put Florida and Texas near the top of the state list. Those 2023 state projections came from a small sample questionnaire, and EPA has replaced them with the inventory-based method. We do not repeat the old state figures because they are superseded; EPA's service line inventory data is housed in its Safe Drinking Water Information System reporting site.
Two local signals are useful. SAWS says it has replaced older lead pipes in the public system since the 1980s. WASD in Miami-Dade says it has no known lead pipes in its own system. Neither statement covers the private pipe on your side of the meter, which is why both utilities ask owners with "unknown" lines to check and report.
Homes built before 1986 deserve the closest look. That year Congress banned non-"lead free" materials in plumbing for drinking water. At the time, "lead free" still allowed up to 8 percent lead in pipes and 0.2 percent in solder and flux. A 2011 federal law cut the pipe and fixture limit to a weighted average of 0.25 percent on wetted surfaces. Texas rules (30 TAC 290.44) apply the same 0.25 percent and 0.2 percent limits to plumbing connected to a public water system.
What are the new EPA lead rules (LCRR and LCRI)?
There are three layers, and it helps to know which one is in force.
| Rule | Year | Main effect for households |
|---|---|---|
| Lead and Copper Rule (LCR) | 1991 | Utilities must control corrosion and sample taps. If more than 10 percent of samples exceed 15 parts per billion (the action level), they must take more steps, including public education and replacing lead lines they control. |
| Lead and Copper Rule Revisions (LCRR) | 2021, compliance Oct. 16, 2024 | Service line inventories, customer notices about line material, and a 24-hour public notice after a lead action level exceedance. |
| Lead and Copper Rule Improvements (LCRI) | Final October 2024, compliance Nov. 1, 2027 | Replace lead and GRR lines within 10 years, stricter tap sampling, and a lower lead action level. |
EPA announced the final LCRI in October 2024 (EPA's page says October 8; Florida DEP dates promulgation to October 16, 2024). Between October 16, 2024 and November 1, 2027, systems follow the original rule plus the retained LCRR pieces: the inventory, the notices, and Tier 1 public notice. EPA's compliance fact sheet says that until November 1, 2027 the 24-hour notice is triggered at 0.015 mg/L (15 ppb), and starting November 1, 2027 it is triggered by the new lead action level of 0.010 mg/L (10 ppb).
Florida DEP's schedule lists full replacement of all lead and GRR service lines by November 1, 2037. By November 1, 2027, systems also must submit a list of schools and licensed child care facilities they serve. From January 30, 2029 on, they must explain every year why any line due for replacement was not replaced.
The health goal behind all of this: EPA sets the goal for lead in drinking water at zero, because there is no known safe level of exposure. EPA and CDC agree there is no known safe level of lead in a child's blood. CDC recommends public health action when a child's blood lead level is 3.5 micrograms per deciliter or more.
Rules can shift with new administrations and court challenges. Before you rely on a date, check TCEQ's Lead and Copper Rule page (Texas) or Florida DEP's Lead and Copper Rule Improvements page.
Who pays to replace a lead service line?
This is the question most people care about, and the honest answer is: it depends on your utility, and many have not announced final policies yet.
- The utility side (main to meter) is the utility's pipe and its job.
- The customer side (meter to house) belongs to the owner. SAWS says that section is the homeowner's property and is not maintained by SAWS. WASD says it is still assessing costs and funding options for compliance.
- Federal money exists for utilities. The Infrastructure Investment and Jobs Act set aside $15 billion in the Drinking Water State Revolving Fund specifically for lead service line replacement, and EPA allots it to states based on the inventory data. In Texas the program runs through the Texas Water Development Board; in Florida, through DEP. Utilities, not homeowners, apply.
What that means for you: if your line is lead or GRR, ask your utility three questions in writing. Is my line in your replacement plan, and when? Will you replace the private side at no cost or partial cost? Will you coordinate so the whole line is done at once? Full replacement matters, because replacing only one side can leave a lead section in place and disturb it.
If you replace your side yourself, use a licensed plumber and pull a permit. In Texas, cities over 5,000 people must require permits for plumbing work, with narrow exceptions for leak repairs and certain fixture swaps (Occupations Code 1301.551). In Tampa, water and sewer replacement outside the structure falls under a plumbing trade permit. Tell the utility before work starts so it can update its inventory and, ideally, replace its side the same day. See plumbing permits and DIY rules and how to hire a plumber.
After a replacement, ask for a water test. WASD says that after any lead line replacement it will sample the water to confirm lead is below 10 ppb.
How do I test my water for lead, and can I get it done for free?
You cannot see, taste or smell lead in water, so testing is the only sure way to know. EPA says tests from certified laboratories cost about $20 to $100 (its Protect Your Tap guide gives $15 to $100). Your state or local drinking water authority can give you a list of certified labs.
How to take a good sample
- Get a kit from a certified lab, not a dip strip. In Florida, Miami-Dade points residents to NELAP-accredited labs found through Florida DEP's lab search.
- Follow the lab's directions exactly. Most ask for "first draw" water that has sat unused in the pipes for at least six hours, such as first thing in the morning.
- Sample the taps you drink and cook from, usually the kitchen faucet. Use cold water only.
- Do not clean the aerator or flush the line right before a first-draw sample unless the lab says to; that can hide a problem.
- If the result is high, take a second sample after flushing. Comparing the two tells you whether the lead is coming from the service line or from fixtures near the tap.
Free or low-cost options
- Ask your utility first. EPA says your water supplier may have useful information, including whether your service line is lead. Some utilities test for customers with lead, GRR or unknown lines.
- Your utility's annual water quality report (Consumer Confidence Report) is due every July 1 and shows the utility's lead sampling results. It is free and often online.
- Florida DEP runs a Voluntary Lead Testing Program listed on its drinking water program pages; check eligibility there.
- Private wells are not covered by utility programs. Ask your county health department. See our well water guide.
For children, the more direct test is a blood test from a pediatrician or the local health department. EPA notes that drinking water can make up 20 percent or more of a person's total lead exposure, and 40 to 60 percent for infants who drink mostly mixed formula.
Do water filters remove lead, and what else can I do today?
Yes, if the filter is certified to reduce lead. EPA's advice is to use a filter certified to remove lead, install it per the directions, replace the cartridge on time, and never run hot water through it. An expired cartridge removes less lead. EPA keeps a consumer tool for finding point-of-use and pitcher filters certified to reduce lead. On the box, look for a certification claim that names lead reduction specifically (often listed under NSF/ANSI Standard 53, or 58 for reverse osmosis units). A filter sold only for taste and odor does not count.
WASD says that if a lead line is confirmed in its area, the county will provide a certified pitcher filter. Ask your utility whether it does the same.
EPA's other steps
- Use cold water for drinking, cooking and baby formula. Hot water pulls more lead from pipes.
- Boiling does not remove lead. It can concentrate it.
- Run the water before drinking if it has been sitting. Showering, doing laundry or running the dishwasher also flushes pipes. Ask your utility how long to flush, since it depends on the length of a lead line.
- Clean faucet aerators regularly. Lead particles can collect in the screen.
- Watch for nearby construction. Ground vibration and street work can suddenly release more lead from a lead line. Filter or flush more during and after the work. TCEQ has given utilities sample language to warn customers of a "service line disturbance", though the notice is voluntary in Texas.
Showering and bathing are generally safe even with lead above the action level, EPA says, because skin does not absorb lead from water. For broader filter choices, see water filtration and quality.
Is lead solder in copper pipes a concern?
It can be, mainly in homes plumbed before the 1986 ban took effect. Copper pipes joined with lead solder can release lead at the joints, especially when water sits overnight or when new water chemistry disturbs old scale. EPA names lead solder as one of the most common lead sources in homes without a lead service line.
How to tell: you usually cannot by looking. Old solder joints are dull gray; newer lead-free solder looks similar. The practical test is the same water test described above, ideally a first-draw sample from the kitchen tap. If lead shows up but your service line is copper or plastic, solder or brass fixtures are the likely sources.
Fixes, cheapest first: a certified filter at the kitchen tap; replacing old brass faucets with current lead-free models; and, if the problem is widespread or the pipes have other issues like pinhole leaks, a repipe. See repiping: PEX vs copper vs CPVC. In Texas, TCEQ rules allow a narrow exception to the lead ban for lead joints needed to repair cast iron pipe, which is a drain material and not part of your drinking water lines.
Do landlords have to disclose lead pipes, and what can renters do?
The federal lead disclosure most people know about covers lead-based paint in housing built before 1978, not water pipes. We did not find a Texas or Florida statute that specifically requires landlords to disclose a lead service line to tenants. That may change as utility notices spread, so treat this as general information and check with a Texas or Florida attorney or your local tenant help line if it matters to your lease.
What does exist: utility notices. The utility must notify the customer of record when a line is lead, GRR or unknown, and for new customers, at the start of service. If the water account is in the landlord's name, the tenant may never see the letter. Renters can:
- Look up the address on the utility's inventory map.
- Ask the landlord in writing for any service line notices received.
- Use a certified filter and the cold-water and flushing steps above.
- Ask the utility whether it offers testing to occupants, not just account holders.
Landlords, see Texas landlord plumbing repairs, Florida landlord plumbing repairs and the landlord maintenance checklist. A tenant who reports lead and gets no response has stronger footing if the request was in writing.
Do schools and daycares in Texas and Florida test for lead?
Testing in schools and child care centers is getting more structured. Under the LCRI, every community water system must submit a list of the schools and licensed child care facilities it serves by November 1, 2027. The schools-and-child-care sampling program in the federal rule builds on that list. TCEQ's lead rule page includes a "Schools and Childcare Program" section, and TCEQ provides lead public education forms written for schools. Florida DEP lists the same November 1, 2027 deadline for the school and child care list.
EPA recommends testing the faucets used for drinking, cooking lunch, and preparing juice and infant formula in schools and child care facilities. If you are a parent, ask your school district or daycare director for their most recent results and the date of sampling. If you run a daycare, ask your water utility whether it will sample for you, and keep the results on file for parents.
Buying or selling a home: how lead lines affect the deal
Buyers in older neighborhoods of Houston, Dallas, San Antonio, Austin, Miami, Tampa, Orlando and Jacksonville should add a service line check to the inspection. Ask the seller for any utility notices. Look up the address on the inventory map. Have the inspector photograph the incoming line. A lead or GRR result is a fair negotiation point, and an "unknown" result is a reason to check before closing.
Sellers can get ahead of it by checking the pipe, reporting the material to the utility so the map shows "non-lead", and keeping the confirmation. In Florida, insurers also look at supply pipe type on the 4-point inspection, which lists galvanized among the materials inspectors must note. See the plumbing home buying checklist and Florida 4-point inspections.
How to choose a provider
- Find your water utility on your bill and open its service line inventory or map.
- Look up your address and note the label: lead, GRR, unknown or non-lead.
- Do the coin and magnet check on the pipe where it enters the house.
- Report the material to your utility with a photo, especially if listed as unknown.
- Order a lead test from a certified lab and sample the kitchen tap as directed.
- Use only cold water for drinking, cooking and baby formula.
- Buy a filter certified for lead reduction and replace cartridges on schedule.
- Clean faucet aerators every few months.
- Ask the utility in writing when your line will be replaced and who pays for the private side.
- If you replace your side, hire a licensed plumber, pull a permit and coordinate with the utility.
- Ask your child's school or daycare for its latest lead results.
- Keep utility notices and test results with your home records for a future sale.
Related plumbing guides
- Do You Have Galvanized Pipes, and Should You Replace Them?
- What Kind of Pipes Do I Have? A Visual Guide by Home Age in Texas and Florida
- Is My Tap Water Safe? How to Read Your Water Report and Choose a Filter or Reverse Osmosis
- How Much Does It Cost to Repipe a House, and Should You Use PEX, Copper or CPVC?
- What Plumbing Should You Check Before Buying a House in Texas or Florida?
- Does a Texas Landlord Have to Fix Plumbing, and What Can Renters Do If They Don't?
- Does a Florida Landlord Have to Fix Plumbing, and What Is the 7-Day Notice?
- Well Water Problems: How Do I Fix Low Pressure, a Failing Pump, Bad Smells and Testing in Texas and Florida?
Plumbing by state and city
Questions people ask
Is lead in water a risk in homes built before 1986?
Yes, the risk is higher. EPA says lead pipes are more likely in older cities and homes built before 1986, the year Congress banned non-lead-free plumbing materials for drinking water. Before then, lead solder was common on copper joints. Homes built after 1986 can still have lead from older brass fixtures, because the lead-free limit for pipes and fixtures was not cut from 8 percent to 0.25 percent until a 2011 federal law. The only way to know is to check the service line and test the water.
My utility letter says my line is "unknown." Should I worry?
Not panic, but act. Unknown means the utility has no record, which is common for older private lines. Do the coin and magnet check at the pipe entering your house, then report what you find through the utility's survey or form. SAWS offers free inspections to eligible unknown properties, and Miami-Dade WASD's survey lets you ask for help. Until you know, use cold water for drinking and cooking and consider a filter certified to reduce lead.
Does a lead service line mean my water is unsafe right now?
Not always. Utilities treat water to make it less corrosive, so many lead lines release little lead most of the time. But levels can spike after water sits, after street work, or after a change in treatment. EPA's health goal for lead is zero. If you have a lead or GRR line, use a certified filter or flushing every day until the line is replaced, and test your water.
Can I replace just my side of the service line?
You can, but coordinate with the utility. Replacing only the private side can leave a lead section on the utility side, and cutting into a lead line can briefly raise lead levels. Call the utility first, ask whether it will replace its portion at the same time, and use a licensed plumber with a permit. Afterward, flush the lines as directed and test your water.
How long will it take for my utility to replace lead lines?
Under the final federal rule, systems must replace all lead and galvanized-requiring-replacement lines within 10 years of the November 1, 2027 compliance date. Florida DEP's schedule lists full replacement by November 1, 2037. Each system's replacement plan is due November 1, 2027. Ask your utility where your street falls in that plan.
Who do I call in Texas or Florida if my utility won't answer?
Start with the utility's customer service and ask for the lead or service line program. In Texas, TCEQ oversees public water systems; its lead and copper team can be reached through the TCEQ Lead and Copper Rule page and LCRR@tceq.texas.gov. In Florida, contact the DEP district office or your county health department that oversees your water system. For health questions about a child, call your pediatrician or local health department.
Do home inspectors check for lead pipes?
Not always. A standard home inspection describes visible plumbing but may not identify the service line material or test the water. Ask your inspector to photograph and identify the incoming line, and order a separate lead test from a certified lab if the home was built before 1986 or the utility lists the line as lead, GRR or unknown.
Is it safe to give my baby formula made with tap water if I have a lead line?
Use extra caution. EPA says infants who drink mostly mixed formula can get 40 to 60 percent of their lead exposure from drinking water. Use only cold water run through a filter certified to reduce lead, or bottled water, for formula until your line is replaced and a test shows low lead. Boiling does not remove lead. Ask your pediatrician about a blood lead test.
Sources
- EPA - Basic Information about Lead in Drinking Water
- EPA - Lead and Copper Rule Improvements
- EPA Fact Sheet - 2021 LCRR Requirements Retained in the Final LCRI and Compliance Dates (Oct. 2024)
- EPA Fact Sheet - 2025 Update to the 7th DWINSA (Nov. 2025)
- EPA 7th DWINSA Fact Sheet (April 2023)
- EPA - Use of Lead Free Pipes, Fittings, Fixtures, Solder and Flux for Drinking Water
- EPA - Protect Your Tap: A Quick Check for Lead
- TCEQ - Lead and Copper Rule Revisions and Lead and Copper Rule Improvements
- TCEQ - Drinking Water Lead and Copper Program
- 30 TAC 290.44 Water Distribution (TCEQ)
- 30 TAC 290.46 Minimum Acceptable Operating Practices (TCEQ)
- Florida DEP - Lead Service Line Inventory
- Florida DEP - Lead and Copper Rule Improvements
- SAWS - Service Line Inventory
- SAWS - Project Lead
- Miami-Dade WASD - Know Your Pipes FAQ
- Texas Occupations Code ch. 1301 (Plumbers)
- City of Tampa - Trade Permit Guidelines
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


