Local Guide · Plumbing
How Much Does It Cost to Repipe a House, and Should You Use PEX, Copper or CPVC?
What a whole-house repipe costs, how PEX, copper and CPVC compare in Texas and Florida heat, and how a documented repipe helps with permits, insurance and resale.
Repiping a house replaces the water supply lines and typically costs $1,500 to $15,000, with a national average of $7,500, according to Angi and HomeAdvisor data cited by Bob Vila. PEX is the most common choice because it is cheaper and faster to install; copper costs more but tolerates heat and sunlight. A repipe needs a permit in nearly every Texas and Florida city, and documenting it helps with Florida 4-point inspections.
Key facts
- Repiping a house typically costs $1,500 to $15,000, national average $7,500 (Angi/HomeAdvisor via Bob Vila).
- Material cost per linear foot: PEX $0.40 to $2, CPVC $0.50 to $1, copper $2 to $8 (Bob Vila).
- Houston requires PEX tubing with chlorine designation code 5 (PEX 5106, 5206 or 5306) under its 2021 UPC amendments.
- Uponor rates white AquaPEX for one month of UV exposure and red or blue AquaPEX for six months.
- Citizens' 4-point form records pipe type and whether the home is original, partially or completely re-piped.
- Citizens says new-business homes over 20 years old with polybutylene piping are not insurable (Feb. 2022 rules).
- Texas cities over 5,000 people must require plumbing permits; leak repair and fixture swaps are exempt, repiping is not (Occ. Code 1301.551).
- Fixr puts a full reroute of supply pipes from the slab to the attic at up to about $15,000.
What does it cost to repipe a house in Texas or Florida?
Repiping means replacing the water supply pipes that carry fresh water to your faucets, toilets, shower valves, water heater and appliances. It usually does not include the drain and sewer pipes. National cost guides put the job in a wide band because homes vary so much.
| Source (date) | What it measured | Published figure |
|---|---|---|
| Bob Vila, citing Angi and HomeAdvisor (updated April 2023) | Whole-house repipe, national | $1,500 to $15,000; national average $7,500 |
| Bob Vila (April 2023) | Plumbing a 3-bedroom, 1,500 sq ft house | $2,280 to $5,120 |
| Bob Vila (April 2023) | Mobile home repipe | $1,500 to $4,000 |
| ThePricer (updated August 25, 2026), compiling a Houston contractor's price schedule | Houston galvanized-to-new repipe, most homes | $4,500 to $11,500; under 1,500 sq ft $4,500 to $7,500 |
| ThePricer (August 2026), citing a Tampa Bay contractor (May 2026) | Tampa Bay repipe | One-story $4,500 to $9,500; two-story $7,000 to $13,000 |
| Fixr (slab leak cost guide) | Rerouting all supply pipes out of the slab into the attic | High end about $15,000 |
Treat these as planning ranges, not quotes. The Houston and Tampa Bay figures come from individual contractors' published schedules compiled by ThePricer, so they reflect local pricing but not a market-wide study. The safest way to know your number is to collect two or three written bids that describe the same scope.
What moves the price
- Number of fixtures and bathrooms. Each sink, toilet, tub, shower, hose bib, ice maker and washer box needs its own run or branch. Bob Vila lists the number of fixtures among the main cost drivers, along with house size and pipe material.
- Stories and layout. A two-story home needs longer runs and more wall openings to reach upstairs fixtures.
- Material. Bob Vila lists material prices of roughly $0.40 to $2 per linear foot for PEX, $0.50 to $1 for CPVC and $2 to $8 for copper. Labor is usually a bigger share than pipe.
- Access. Slab homes, finished ceilings, tile walls and tight attics add time.
- Wall and ceiling repair. Many quotes include only rough patching. Bob Vila cites $50 to $75 per square foot for drywall repair and $45 to $90 per square foot for ceilings when a separate contractor does it.
- Permits and inspection. Bob Vila lists plumbing permits at $50 to $500 depending on the city and job.
PEX vs copper vs CPVC: how do they compare?
Almost every modern repipe in Texas and Florida uses one of three supply materials. Here is how they stack up on the points that matter in hot, humid states.
| Factor | PEX (cross-linked polyethylene) | Copper (Type L or M tube) | CPVC (chlorinated PVC) |
|---|---|---|---|
| Material cost per linear foot (Bob Vila, 2023) | $0.40 to $2 | $2 to $8 | $0.50 to $1 |
| Lifespan estimate (Bob Vila) | 80 to 100 years | 50 to 100 years | 50 to 70 years |
| Lifespan estimate (InterNACHI chart) | 40 years | 50 to 70 years | Not listed separately ("plastic water lines" 50 to 75) |
| Flexibility | Bends around corners, long runs with few fittings | Rigid, needs fittings at every turn | Rigid, glued fittings at every turn |
| Sunlight (UV) | Must be shielded; Uponor rates its white AquaPEX for one month of UV exposure, red and blue for six months | Not affected by UV | Should be protected from long sun exposure per maker instructions |
| Chlorine | Rated by a chlorine code; Houston requires code 5 tubing (PEX 5106, 5206 or 5306) | Corrosion depends on water chemistry | Resistant to chlorinated water when installed to listing |
| Freeze behavior | Can expand slightly, but fittings and frozen sections can still fail | Splits when water freezes inside | Brittle when cold; can crack |
| Rodents | Bob Vila notes it is susceptible to chewing rodents | Not chewed | Can be chewed |
| Typical install | Manifold or home-run, or trunk and branch | Trunk and branch with soldered or press joints | Trunk and branch with solvent-cemented joints |
Why do the lifespan numbers disagree? They come from different sources with different methods. Bob Vila's figures are marketing-style estimates for new material. InterNACHI's chart, used by home inspectors, gives conservative "guideline" numbers and warns they are not guarantees. PEX has only been in wide U.S. use for a few decades, so nobody has 100 years of field data yet. Plan around the conservative number and be pleasantly surprised.
The short version
- PEX is the most common choice for whole-house repipes because it is cheaper to buy and much faster to install, which cuts the labor bill and the number of wall openings.
- Copper costs more but tolerates heat and sunlight, does not attract rodents, and is the choice some owners want for exposed runs or resale perception.
- CPVC is the cheapest rigid plastic and still appears in Florida homes and repairs, but it is less forgiving of rough handling and age than PEX.
Is PEX safe for drinking water?
PEX sold for drinking water in the U.S. must be listed to national standards. Uponor, a major PEX maker, says its AquaPEX meets the highest chlorine-resistance requirement under ASTM F876 and F877, the standard specifications for PEX tubing and systems. Local codes add their own rules: the City of Houston's amendments to the 2021 Uniform Plumbing Code require PEX tubing to carry a chlorine designation code of 5, meaning it is rated for continuous exposure to chlorinated water at 140 degrees F, and they list PEX 5106, 5206 and 5306 as acceptable markings.
What to check on your job:
- The tubing print line shows the standard (ASTM F876/F877), a potable water listing, and the chlorine code.
- Fittings are the type the tubing maker lists for that tubing. Mixing brands of tubing, rings and fittings can void the manufacturer's warranty.
- Brass fittings meet the federal "lead-free" limit. Under the Safe Drinking Water Act as amended in 2011, lead-free means no more than a weighted average of 0.25 percent lead on wetted surfaces of pipes, fittings and fixtures, per EPA. Texas rules (30 TAC 290.44 and 290.46) apply the same limits to plumbing connected to a public water system.
Some people notice a plastic taste in new PEX for the first days. Flushing the lines usually clears it. If it does not, ask the installer and the tubing maker.
PEX-A vs PEX-B: does it matter?
PEX is grouped by how the plastic is cross-linked during manufacturing. PEX-A is usually more flexible and is often joined with expansion fittings, where the tube is stretched and shrinks back over the fitting. PEX-B is stiffer and is usually joined with crimp or clamp rings over an insert fitting. Both types are sold for potable water when listed to the same ASTM standards.
For a homeowner, the practical differences are these:
- Fitting style. Expansion fittings have a full-bore opening, while insert fittings narrow the inside diameter at each joint. On long runs with many fittings this can slightly reduce flow.
- Kink repair. PEX-A kinks can often be reversed with heat per the maker's instructions. PEX-B kinks usually must be cut out.
- Cost. PEX-B tubing and tools are typically cheaper.
- Warranty. Warranties usually require the maker's own fittings and an installer who follows its instructions.
The choice matters less than the installer's workmanship and whether the tubing and fittings carry the right listings and the local chlorine rating.
Does PEX hold up in a Florida attic or Texas heat?
In many Texas and Florida slab homes, the new pipe goes through the attic, because that avoids breaking the slab. Attics in both states get very hot in summer. Uponor's customer FAQ says its PEX can be installed in attics but must be protected from excessive cold and heat, and recommends placing insulation only above the pipe, so the pipe stays on the conditioned side of the insulation. Uponor rates its domestic hot water piping for a maximum of 140 degrees F at 80 psi in that FAQ, and its spec sheets list higher short-term ratings.
Questions to ask your installer about an attic run:
- Will the pipe lie on top of the ceiling drywall and under the insulation, or be strapped to rafters in open air? Under the insulation is usually cooler in summer and warmer in a freeze.
- Will any PEX be exposed to sunlight through gable vents, soffits or skylights? Uponor rates white AquaPEX for only one month of UV exposure.
- How will lines be insulated where they pass exterior walls? Texas freezes such as February 2021 caused widespread broken pipes, and attics and exterior walls are among the highest-risk spots the Red Cross lists.
- Will drain-down valves let you empty the system if you leave the house in a hard freeze?
For outdoor runs, such as to a pool equipment pad or hose bib, ask for pipe that is rated for that location or sleeved and protected from sunlight.
Why does copper get pinhole leaks?
A pinhole leak is a tiny hole that forms from the inside of copper pipe, usually from localized pitting corrosion. It often shows up as a fine spray or a slow drip and a water stain. Owners often find one, then another a few months later in a different spot.
Corrosion engineers point to several contributing causes, and more than one is usually involved:
- Water chemistry. The pH, alkalinity, dissolved minerals and disinfectant in your water affect how copper corrodes. Many Texas and Florida utilities disinfect with chloramine, which EPA says some systems adopted because it provides longer-lasting disinfection through the pipe network and helps meet disinfection byproduct rules. Your utility's annual water quality report lists its disinfectant and water chemistry.
- High water velocity from undersized pipe or a recirculation pump set too high, which erodes the inside of the pipe at elbows.
- Installation residue, such as excess solder flux left inside joints.
- Thin-wall pipe (Type M) that has less metal to lose than Type L.
- Electrical grounding problems that put current on the water pipe.
If you have one pinhole leak, a spot repair is reasonable. If you have several in a year, or leaks in different branches, that is the classic case for a repipe. Because the cause is often the water itself, replacing copper with copper in the same water may lead to the same problem years later, which is one reason many owners in that situation switch to PEX.
When should I repipe instead of repairing leaks?
There is no law that says when to repipe. These are the signals most owners use:
- Repeat leaks. A second or third leak in a year, in different spots, suggests the whole system is aging.
- Problem materials. Polybutylene, galvanized steel, or early PEX-AL-PEX systems that insurers or inspectors flag. See our guides to polybutylene and galvanized pipe.
- Insurance pressure. In Florida, a 4-point inspection that lists polybutylene or galvanized pipe can make a home hard to insure.
- Symptoms of corroded pipe. Bob Vila lists discolored water, poor water pressure, odd-tasting water and repeated leaks among common signs.
- Slab leaks. In a slab home, a second slab leak often makes rerouting overhead cheaper than another round of jackhammering. See our slab leak guide.
- Renovation timing. If walls are already open for a kitchen or bath remodel, repiping that area costs much less.
A useful rule of thumb: add up what you spent on leak repairs, water damage deductibles and drywall patching in the last few years. If the total is heading toward a meaningful share of a repipe quote, and the pipe material is past its expected life, a repipe usually wins.
Overhead repipe vs under-slab: which is better for slab homes?
Most homes in Houston, Dallas, San Antonio, Austin, Tampa, Orlando and Jacksonville sit on concrete slabs, and many original water lines run in or under the slab. When those lines leak, you have two choices.
| Approach | How it works | Pros | Cons |
|---|---|---|---|
| Repair under the slab | Locate the leak, then break the floor or tunnel under the foundation to fix it | Keeps the original layout | Fixr lists tunneling at $900 to $2,000 and breaking the slab at $500 to $3,000 for one leak; other under-slab lines keep aging |
| Reroute overhead | Abandon the slab lines and run new pipe through the attic and walls down to each fixture | Future leaks are reachable; no floor damage | Wall openings; attic heat and freeze protection needed; Fixr puts a full reroute at up to about $15,000 |
Codes in the region discourage water lines inside concrete. Houston's amendments require approved materials to be installed without joints and sleeved where they penetrate the floor, with no part of the water pipe in contact with concrete, and they bar galvanized pipe in or under slabs. That is one reason many plumbers prefer overhead routing for repipes.
How long does a repipe take, and can I live in the house?
Bob Vila says a whole-house repipe can take from a few days to a few weeks, depending on house size, access and scope, and cites labor of about 15 hours as an example for one job. In practice, a typical single-story home is often done in a few working days, with drywall patching after inspection.
You can usually stay in the home. Common arrangements:
- Water is shut off during the workday and restored most evenings.
- Crews work room by room, covering floors and furniture with plastic.
- There will be a gap between "pipes done" and "walls closed," because the inspector must see the new pipe before patching.
If anyone in the home has breathing problems, ask how the crew controls drywall dust. If you have pets, plan for doors left open and strangers in the house.
What should a repipe quote include?
Bob Vila notes that repiping usually covers supply lines only, not drains, sewer pipes or fixtures. Quotes differ most in what they leave out. Ask each bidder to answer these in writing:
| Item | Ask |
|---|---|
| Material and brand | Which PEX type and brand, or copper Type L or M? What fittings? |
| Fixtures served | Every sink, toilet, tub, shower, ice maker, washer, water heater and hose bib listed? |
| Shutoffs | New fixture stop valves and a new main shutoff included? |
| Water heater connections | New connectors and, where needed, an expansion tank? |
| Main service line | Is the line from the meter to the house included? Bob Vila lists water main replacement at $600 to $2,500. |
| Wall and ceiling repair | Rough patch only, or patch, texture and paint? |
| Permit and inspections | Who pulls the permit and pays the fee? |
| Warranty | Labor warranty in years, plus the maker's pipe warranty? |
| Payment schedule | Deposit amount and what triggers each payment? |
For hiring steps and how to check a license in each state, see how to hire a plumber.
Do I need a permit to repipe in Texas or Florida?
Yes, in nearly every city. Repiping is new work, not a simple repair.
Texas
- Texas Occupations Code 1301.551 requires cities over 5,000 people to regulate plumbing by ordinance and require a permit before plumbing work. The short list of exceptions covers repairing leaks and swapping faucets, toilet fill valves, garbage disposals and toilets, not repiping.
- Houston's amendments let an owner do plumbing on an owner-occupied homestead and apply for a permit, but do not waive the permit or fees.
- Dallas enforces the 2021 International Plumbing Code with local amendments (Dallas Plumbing Code, Chapter 54). San Antonio adopted the 2024 ICC codes, including the IPC, in January 2025. Austin lists the 2024 Uniform Plumbing Code.
Florida
- Tampa's plumbing trade permit list includes "re-pipe of interior water distribution" as a trade permit without plan review.
- Miami-Dade's exemption list says stopping a leak is exempt, but if a concealed water pipe must be removed and replaced, it is new work that needs a permit and inspection.
- Under Fla. Stat. 553.73, the Florida Building Code in effect on the date of permit application governs the work.
Keep the permit number and final inspection record. Insurers, home inspectors and buyers often ask when and how the home was repiped. For rules by city, see plumbing permits and DIY rules.
Does repiping lower insurance or raise home value?
No source we reviewed gives a reliable dollar figure for how much a repipe raises value or cuts premiums, so be wary of anyone who promises one. The clearer effect is on insurability and on what inspectors write.
Florida
- Citizens Property Insurance Corporation's 4-point inspection form asks the inspector to check the supply and drain pipe types (copper, PEX, PVC/CPVC, galvanized, cast iron, polybutylene, ABS) and whether the home is original, partially re-piped or completely re-piped, with the year and extent of the work.
- Citizens' February 2022 eligibility rules say new-business homes more than 20 years old with polybutylene piping are not insurable by Citizens.
- The form also asks about active or prior leaks and requires photos of the water heater, under-cabinet plumbing and exposed valves.
Practical tip: keep the final permit, invoice listing the material, and photos of the new pipe at the water heater and main shutoff. A 4-point inspector can then mark "completely re-piped" with a year, which is what underwriters look for. See our Florida 4-point plumbing guide.
Texas
Texas insurers rely less on 4-point forms, but leaks still matter. The Texas Department of Insurance (TDI) says most homeowner policies cover sudden water damage like a burst pipe but usually not gradual leaks or seepage, and some policies exclude seepage lasting 14 days or more. TDI also notes insurers may nonrenew after three or more non-weather claims in three years. Fewer leaks means fewer claims on your record.
Can rats or termites damage PEX?
Rodents can chew plastic pipe. Bob Vila specifically notes PEX is susceptible to damage from rodents. In Florida and Texas, roof rats commonly travel through attics, which is where overhead repipes run. If you have had rodent activity, seal entry points before the repipe and ask whether exposed attic runs can be covered or sleeved. Copper is not chewed by rodents.
Termites eat wood, not plastic. We found no reliable source showing termites attack PEX as food. They can tunnel through soft materials next to their path, so keep up your termite treatment either way.
Texas and Florida notes: what is different in each state?
Texas
- Expansive clay soils around Houston, Dallas and San Antonio move slabs, which stresses under-slab pipes. Many owners choose an attic reroute after the first slab leak.
- Hard freezes, as in February 2021, mean attic and exterior-wall pipe needs insulation and a known shutoff. See frozen pipes in Texas.
- Repipes must be done by a TSBPE-licensed plumber under a Responsible Master Plumber, except an owner working on their own homestead where allowed. See the Texas license guide.
Florida
- Insurability drives many repipes, especially in homes built roughly 1978 to 1995 with polybutylene.
- Older Miami, Tampa and Jacksonville homes may have galvanized supply lines and cast iron drains; repiping the supply side does not fix the drains. See cast iron pipes in Florida.
- Only Florida-licensed plumbing contractors (or owner-builders under the state exemption) can pull a repipe permit. See the Florida license guide.
City pages: Houston, Dallas, Miami, Tampa.
Three example repipe scenarios
These examples show how scope drives price. They are illustrations, not quotes.
- 1987 single-story Orlando home with gray polybutylene. The owner needs a new insurer. Scope: PEX to every fixture, new stops, new main shutoff, permit, rough patch. Expect to land within the Tampa Bay one-story range ThePricer reported ($4,500 to $9,500 in 2026). Paint and texture may be extra.
- 1965 Houston slab home with a second slab leak. Scope: abandon slab lines, PEX through the attic under the insulation, insulated drops in exterior walls. Fixr puts a full under-slab-to-attic reroute at up to about $15,000 at the high end.
- 1950s Miami home with galvanized supply lines and low pressure. Scope: replace galvanized with PEX or copper, include the line from the meter, and ask the utility whether its service line was ever lead. See lead service lines.
How to choose a provider
- Identify your current pipe material at the water heater, under sinks and at the main shutoff.
- Write down every fixture and appliance that needs water so bids cover the same scope.
- Get two or three written bids naming the pipe brand, type and fittings.
- Confirm each bidder's license with TSBPE (Texas) or DBPR (Florida).
- Ask who pulls the permit and whether fees are included.
- Ask whether wall repair is rough patch only or finished and painted.
- For attic runs, ask how pipe will be protected from heat, sunlight and freezing.
- Clear rodent activity in the attic before overhead PEX goes in.
- Plan for water shutoffs during workdays and protect floors and furniture.
- Keep the permit, final inspection, invoice and photos for insurers and buyers.
- In Florida, give the documents to your 4-point inspector and insurance agent.
Related plumbing guides
- Do You Have Polybutylene Pipe, and Can You Still Get Insurance?
- Do You Have Galvanized Pipes, and Should You Replace Them?
- What Kind of Pipes Do I Have? A Visual Guide by Home Age in Texas and Florida
- Slab Leaks in Texas and Florida: What Are the Signs, Fixes, Costs and Insurance Rules?
- What Does a Florida 4-Point Inspection Check on Plumbing, and How Do You Pass?
- Do I Need a Permit? Plumbing Permits and DIY Rules in Texas and Florida
- How Do You Hire a Plumber in Texas or Florida and Check the License?
- How Do I Know If I Have Lead Pipes? Checking Your Service Line in Texas and Florida
Plumbing by state and city
Questions people ask
How much does it cost to repipe a 2,000 square foot house?
No single figure fits every 2,000 square foot home, because fixture count, stories and access matter more than square footage. Bob Vila, citing Angi and HomeAdvisor, puts whole-house repiping at $1,500 to $15,000 with a $7,500 average. A Houston contractor schedule compiled by ThePricer in 2026 showed most homes at $4,500 to $11,500, and a Tampa Bay contractor listed two-story homes at $7,000 to $13,000. Get two or three written bids with the same scope to compare fairly.
Is copper better than PEX?
Neither is better in every case. Copper handles heat and sunlight, does not attract rodents and has a long track record, but it costs more and can develop pinhole leaks in some water. PEX is cheaper, faster to install, resists scale and freezes better, but must be kept out of sunlight and installed with listed fittings. In most Texas and Florida whole-house repipes, PEX wins on total cost. Copper makes sense for exposed runs or if you prefer metal.
Is CPVC still used in Florida?
Yes. CPVC remains a code-listed water pipe material and you will find it in many Florida homes built from the 1980s onward and in repairs. Citizens' 4-point form lists PVC/CPVC as a normal pipe type, not a red flag. Older CPVC can become brittle, especially where it is exposed to heat or was handled roughly, so care is needed during repairs. For a full repipe, many Florida plumbers now quote PEX instead because it needs fewer fittings.
Does homeowners insurance pay to repipe a house?
Usually no. Policies generally pay for sudden water damage, not for replacing worn-out pipe. TDI says most Texas policies cover sudden and accidental water damage such as a burst pipe but usually not gradual leaks. Florida policies work similarly. The insurer may pay to tear out and replace the damaged wall or floor to reach a covered leak, but the pipe itself and a whole-house repipe are typically your cost. Read your policy and ask your agent.
Will a repipe help me pass a Florida 4-point inspection?
A completed and permitted repipe usually resolves the plumbing concerns that cause a 4-point problem, such as polybutylene or galvanized supply pipe. Citizens' form asks whether the home is completely re-piped and in what year, and Citizens says new-business homes over 20 years old with polybutylene are not insurable. Keep the permit, invoice and photos so the inspector can document the work. Each insurer sets its own rules, so ask your agent what they need.
Do I need to replace my drain pipes when I repipe?
Not necessarily. Repiping normally means water supply lines only. Drain, waste and vent pipes are a separate system with their own lifespan. If your home has original cast iron drains, ask for a camera inspection of the drains to decide separately. Bob Vila notes sewer line replacement averages just under $3,000 as an add-on example, but costs vary widely with length, depth and method.
Can I repipe my own house?
In Texas, an owner may do plumbing on an owner-occupied homestead where the city allows it, as Houston's amendments do, but a permit and inspections are still required. In Florida, Fla. Stat. 489.103(7) lets owners act as their own contractor on a one- or two-family home for their own occupancy or use and not offered for sale or lease, with direct onsite supervision; selling within one year creates a presumption it was built for sale. A repipe is a large job with many joints, so most owners hire a licensed plumber. Check with your city building department first.
How do I know if my house has already been repiped?
Look at the pipe entering the water heater, under sinks and at the main shutoff. New PEX or copper throughout, with modern quarter-turn stops, suggests a repipe. Then check permit history with your city or county building department, which lists past plumbing permits by address. Florida 4-point inspectors also note whether a home is original, partially or completely re-piped. Ask the seller for invoices and warranties if you are buying.
Sources
- Bob Vila - How Much Does It Cost to Repipe a House? (Angi/HomeAdvisor data)
- ThePricer - Replacing Galvanized Pipes Cost (updated Aug. 25, 2026)
- Fixr - Slab Leak Repair Cost
- Uponor - Customer Support FAQ (AquaPEX UV, temperature, attic installation)
- City of Houston - Houston Amendments to the 2021 Uniform Plumbing Code
- InterNACHI - Standard Estimated Life Expectancy Chart for Homes
- InterNACHI - Florida Life Expectancy Chart
- EPA - Basic Information about Lead in Drinking Water
- EPA - Chloramines in Drinking Water
- 30 TAC 290.44 Water Distribution (TCEQ)
- Citizens Property Insurance Corp. - Sample 4-Point Inspection Form Insp4pt 03 25
- Citizens Property Insurance Corp. - Clarification of February 1, 2022, Eligibility Rules
- Texas Occupations Code ch. 1301 (Plumbers)
- City of Dallas Building Inspection - Plumbing & Mechanical
- City of San Antonio DSD - Codes & Ordinances
- City of Austin - Building Technical Codes
- City of Tampa - Trade Permit Guidelines
- Miami-Dade County RER - Permit Exemptions (PDF)
- Fla. Stat. 553.73 Florida Building Code
- TDI - When are water damage and mold covered by insurance?
- Fla. Stat. 489.103 Exemptions (owner-builder)
- American Red Cross - Frozen Pipes
- NWS Houston/Galveston - Valentine's Week 2021 Winter Outbreak
- TDI - Home insurance guide
- TDI - Texas Homeowners Policies (comparison report)
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


