New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Plumbing

What Kind of Pipes Do I Have? A Visual Guide by Home Age in Texas and Florida

Copper, galvanized, PEX, CPVC, polybutylene, cast iron or lead: how to identify each one in 15 minutes, what was used in each decade, how long each lasts, and which ones Florida insurers flag.

Check the pipes at your water heater, under sinks, at the main shutoff and in the attic. Copper is penny-colored; galvanized is gray metal a magnet sticks to; lead is soft gray metal that scratches shiny silver. Rigid cream plastic is usually CPVC, flexible red or blue plastic is PEX, and flexible gray plastic stamped PB2110 is polybutylene. Read the printing on plastic pipe, and use your home's build year as a clue, not proof.

Key facts

  • Polybutylene was manufactured from 1978 to mid-1995 and installed in up to 10 million US homes (InterNACHI); it is usually stamped PB2110.
  • A 2000 Cozen O'Connor paper said most polybutylene systems and lawsuits were in Florida, California and Texas.
  • Congress banned non-lead-free plumbing for drinking water in 1986; EPA says lead pipes are more likely in homes built before 1986.
  • Cast iron drainpipes are common in homes built before 1975 and have drawn heavy claims activity in Florida (Insurance Journal, 2022).
  • Citizens' 4-point form asks inspectors to check copper, PEX, PVC/CPVC, galvanized, cast iron, polybutylene and ABS for both supply and drain systems.
  • InterNACHI estimates copper water lines last 50 to 70 years and PEX about 40 years; Bob Vila (2023) cites 80 to 100 years for PEX.
  • Bob Vila's 2023 guide puts material costs at $2 to $8 per foot for copper, $0.40 to $2 for PEX and $0.50 to $1 for CPVC.
  • The Kitec plumbing settlement claim deadline was January 9, 2020, and final payments went out in December 2024 and January 2025.

Start here: supply pipes vs drain pipes

Every house has two separate pipe systems, and they are often made of different materials.

  • Supply (water) pipes carry pressurized clean water to faucets, toilets, the water heater and appliances. They are small, usually 1/2 inch to 1 inch across. Common materials: copper, galvanized steel, CPVC, PEX, polybutylene, and in older service lines, lead.
  • Drain, waste and vent (DWV) pipes carry used water and sewage out by gravity and let sewer gas vent through the roof. They are bigger, often 1-1/2 to 4 inches. Common materials: cast iron, PVC (white), ABS (black), and in some old sewer lines, clay or Orangeburg.

This matters because the questions differ. A supply leak sprays under pressure and runs until you shut the water off. A drain problem shows up as slow drains, backups or smells. Florida's insurance 4-point inspection form asks about each system separately: it has boxes for the age of the supply piping and the age of the drain piping, and for whether each is original, partially re-piped or completely re-piped.

InterNACHI's inspector guidance adds one useful rule of thumb: polybutylene is not used for waste, drain or vent piping. So gray plastic on a drain is something else.

How do I tell what pipes my house has?

You can identify most pipes in 15 minutes with a flashlight, a coin and a magnet. Check these spots:

  1. The water heater. The pipes entering the top are easy to see. Look at least a foot or two away from the heater, since short connectors are often a different material from the house piping.
  2. Under the kitchen and bathroom sinks. Look where the pipe comes out of the wall or floor (the "stub out"), behind the shutoff valve.
  3. The main shutoff and where the line enters the house. In Texas and Florida slab homes this is often on an outside wall, in the garage, or in a utility closet.
  4. The attic. Many slab homes in Houston, Dallas, Tampa and Orlando have supply pipes running overhead, especially if the house was re-piped after a slab leak.
  5. The water meter box. You can see the service line where it leaves the meter.
  6. Cleanouts and the laundry standpipe for drain pipe material.

Quick identification chart

What you seeLikely materialQuick test
Penny-colored metal, may have green or blue-green crust at jointsCopperMagnet does not stick; scratch shows bright copper
Dull silver-gray metal with threaded joints and fittingsGalvanized steelMagnet sticks
Dull gray soft metal, smooth bulged joints, usually only the service lineLeadScratches easily to shiny silver; magnet does not stick
Rigid cream, off-white or light yellow plastic, glued fittings, small diameterCPVCPrinting often says CPVC and ASTM D2846
Flexible red, blue, white or clear plastic tubing, crimp rings or expansion fittingsPEXPrinting says PEX; bends in long curves
Flexible gray (sometimes silver, white, black or blue) plastic, crimp rings, 1/2 to 1 inchPolybutyleneOften stamped PB2110
Orange or blue flexible tubing, sometimes with a layer of aluminum, brass fittingsPEX-AL-PEX (including Kitec)Look for brand printing; ask a plumber
White rigid plastic, 1-1/2 inches and up, on drainsPVCPrinting says PVC and DWV or Schedule 40
Black rigid plastic on drainsABSPrinting says ABS
Heavy dark gray or black metal drain pipe, hub joints or no-hub bandsCast ironMagnet sticks; rings dull when tapped

Read the printing. Most plastic pipe has its material, size and standard printed every few feet. That single line of text often settles the question.

Be careful with colors. InterNACHI notes that black or white pipe might not be polybutylene: black flexible pipe may be polyethylene, and white rigid pipe is usually PVC or CPVC. PEX also comes in gray. Color is a clue, not proof.

What pipes were used in homes by decade?

Builders changed materials over time, so the year a home was built is a strong hint. Use this as a starting point, then confirm with your own eyes, because many homes have been partly re-piped and one house can contain three or four materials.

Era builtTypical supply pipeTypical drain pipeWhat to watch
Before 1960Galvanized steel; lead service lines in some older city neighborhoodsCast iron; clay or Orangeburg sewer lateralsRust, low pressure, lead risk upstream of galvanized
1960s to mid-1970sCopper becomes common, galvanized still found; copper joints made with lead solderCast iron in most Florida and Texas slab homesCast iron drains under slabs; Insurance Journal reports cast iron is common in homes built before 1975
1978 to mid-1990sPolybutylene in many tract homes and mobile homes; copper elsewherePVC and ABS replace cast iron in many new homesPolybutylene insurability; lead solder before 1986
Mid-1990s to 2000sCopper and CPVC; PEX and PEX-AL-PEX appearPVCKitec-type systems; condition of CPVC in hot attics
2010s to todayPEX dominant in new construction; copper in some custom workPVCFitting quality, proper support and UV protection for PEX

Three dates anchor the timeline with sources:

  • 1978 to mid-1995: InterNACHI dates polybutylene manufacturing to this period and says it went into up to 10 million US homes. A 2000 Cozen O'Connor paper estimated about 6 million homes plus 3 million mobile homes, and said most of the systems and lawsuits were in Florida, California and Texas.
  • 1986: Congress banned non-lead-free materials in drinking water plumbing. EPA says lead pipes are more likely in homes built before 1986. At that time "lead free" still allowed 8 percent lead in pipe and 0.2 percent in solder.
  • 2011 law: cut the lead limit for pipes, fittings and fixtures to a weighted average of 0.25 percent on wetted surfaces.

What pipes are in a 1970s Florida home, or a 1980s Texas home?

1970s Florida (Miami, Tampa, Orlando, Jacksonville)

Expect copper supply lines, sometimes with galvanized sections, and cast iron drains under the slab. The cast iron is now one of the most argued-about items in Florida insurance. Insurance Journal reported in 2022 that cast iron drainpipes in homes built before 1975 had become a target of large plaintiffs' firms, while defense engineers said full replacement is often unnecessary. If you own a 1970s Florida home, a camera inspection of the drains tells you far more than the year. See cast iron pipes in Florida and sewer camera inspections.

Late-1970s Florida homes may also have polybutylene, since production began in 1978. The water heater and the stub-outs under sinks are the places to look.

1980s Texas (Houston, Dallas, San Antonio, Austin)

Many 1980s Texas subdivisions were plumbed with polybutylene or copper. In 1994 the manufacturers proposed a $750 million national polybutylene settlement in Beeman v. Shell Oil in Harris County, Texas (the judge rejected it; the later national settlement was Cox v. Shell), a sign of how widely the material was used there. Drains in this era shift from cast iron to PVC or ABS. If a home has been through a slab leak, the supply may have been rerouted into the attic in PEX or CPVC.

2000s and newer, both states

Expect PEX or CPVC supply lines and PVC drains. If your 2000s home has orange or blue layered tubing with brass fittings, check whether it is a PEX-AL-PEX system such as Kitec, discussed below.

What is the difference between PVC, CPVC, PEX and ABS?

MaterialWhat it isUsed forLookJoined by
PVCPolyvinyl chlorideDrains, vents, sewer laterals, irrigation, cold water service lines. Not for hot water.White, rigid, larger sizesPrimer and solvent cement
CPVCChlorinated PVC, rated for hot waterHot and cold supplyCream, tan or off-white, rigid, small sizesSolvent cement
PEXCross-linked polyethyleneHot and cold supply; radiant heatFlexible; red, blue, white, grayCrimp or clamp rings, expansion fittings, press fittings
ABSAcrylonitrile butadiene styreneDrains and ventsBlack, rigidSolvent cement (one step)

What does blue and red pipe mean? On PEX, red usually marks hot water and blue marks cold. White PEX can be either. The color is for convenience; the pipe itself is the same material and rating. Do not assume a red pipe is hot without checking the water heater connection.

InterNACHI notes that PEX is more flexible and more easily coiled than polybutylene and handles higher temperatures than plain polyethylene. Bob Vila's 2023 repipe cost guide describes PEX as resistant to chlorine and scale and CPVC as less flexible than PEX and less durable than copper.

How long does each type of pipe last?

Pipe life depends heavily on water chemistry, installation quality and, in Texas and Florida, heat and soil. Published ranges vary by source, so we show two side by side. Treat them as estimates, not guarantees.

MaterialInterNACHI estimated lifeBob Vila / Angi (2023)
Copper water lines50 to 70 years50 to 100 years
PEX40 years80 to 100 years
CPVCPlastic water lines: 50 to 75 years50 to 70 years
ABS and PVC waste pipe50 to 80 yearsn/a
Cast iron waste pipe, above ground60 yearsn/a
Cast iron waste pipe, below ground50 to 60 yearsn/a
Galvanized steel supplyNot listedn/a; see our galvanized guide
PolybutyleneNot listed; failure is unpredictablen/a

The PEX numbers disagree by a factor of two, which is a good reminder that PEX has not been in wide use long enough for real-world lifespans to be settled. What you can control: keep PEX out of direct sunlight, support it properly, and use fittings and installers that meet the manufacturer's instructions.

For the full replacement decision, see repiping: PEX vs copper vs CPVC.

What is the gray plastic pipe in my house? Is it always polybutylene?

Gray flexible plastic supply pipe in a house built between 1978 and the mid-1990s is very often polybutylene. InterNACHI's identification tips: it is usually stamped PB2110, it is flexible and sometimes curved, it is 1/2 inch to 1 inch in diameter, and it is most commonly gray, though it can be white, silver, black or blue. Blue polybutylene was used mainly outdoors for cold water service lines. Cozen O'Connor's paper says gray and silver PB is mostly found indoors and blue PB underground at the water service.

But gray is not always PB. Some PEX is gray. Gray PVC electrical conduit sometimes runs near plumbing. Check the printing, and check the fittings: older PB systems often used plastic (acetal) or copper crimp-ring fittings.

Also check the whole system. InterNACHI warns that some copper systems used PB at junctures, such as PB linking to copper stub-outs that feed bathroom fixtures. So copper under the sink does not rule out PB in the wall.

Why it matters: the leading theories for PB failure are that the pipe and its acetal fittings break down from chlorine in water supplies, and that crimp rings were clamped too hard. Damage starts inside the pipe, so it cannot be seen from outside. InterNACHI notes that home inspectors are not required to report PB and cannot test its strength. See polybutylene pipe and insurance.

What is Kitec pipe?

Kitec is a brand of PEX-AL-PEX plumbing, a layered tube with plastic inside and outside and a thin aluminum layer in the middle, sold with brass fittings. It was used in some homes built roughly from the mid-1990s through the 2000s. Problems reported with these systems centered on the fittings, which led to class action litigation in the United States and Canada.

The settlement is effectively over. The official Kitec settlement site says the claim deadline was January 9, 2020. Courts approved the final allocation in September 2024, checks went out in late December 2024 and early January 2025, and a July 9, 2025 update says payments have been issued and the stale date has passed. Claimants who believe a valid claim went unpaid can contact the settlement administrator at info@kitec-settlement.com or 1-877-337-1293.

How to spot it: look near the water heater and under sinks for flexible orange (hot) or blue (cold) tubing with brass fittings and brand printing on the pipe. Many plumbers can confirm it on sight. Note that we could not load a primary source with a full identification guide, so have a licensed plumber confirm before you make a repipe or insurance decision.

Which pipe types do Florida insurers dislike?

Florida insurers use the 4-point inspection (roof, electrical, HVAC, plumbing) to decide whether to cover older homes. Citizens Property Insurance's sample form asks the inspector to check every supply and drain pipe type present from this list: copper, PEX, PVC/CPVC, galvanized, cast iron, polybutylene, ABS, and other. It also asks for the age of the supply and drain piping and whether each is original, partially re-piped or completely re-piped, with the year and extent of any renovation.

MaterialHow insurers usually treat it
PolybutyleneNamed on the form; widely treated as a red flag, and many carriers decline or require replacement
Galvanized supplyOften a concern because of age and corrosion
Cast iron drainsIncreasing scrutiny given the claims wave reported in 2022
Kitec / PEX-AL-PEXNot named on the Citizens form; ask your agent whether the carrier has a rule, and disclose it if asked
Copper, PEX, CPVC, PVCGenerally acceptable when in good condition

The treatments above are general patterns, not any one carrier's rulebook. Underwriting rules vary by carrier and change often, so ask your agent which materials that specific insurer accepts before you buy or renew. The form also asks about active or prior leaks and the condition of fixtures and appliance connections, and requires photos of the water heater (including the relief valve), under-cabinet plumbing and drains, and exposed valves. It must be signed by a verifiable Florida-licensed professional.

In Texas there is no statewide equivalent of the Florida 4-point, but pipe type still matters in a sale and in claims. See the Florida 4-point plumbing guide and what plumbing insurance covers.

What is the best pipe material for a slab home?

Most homes in Houston, Dallas, San Antonio, Austin and much of Florida sit on concrete slabs, with supply and drain lines under or in the slab. When supply lines under the slab fail, owners face a choice: repair in place, or reroute.

  • Rerouting overhead runs new supply lines through the attic and down the walls, abandoning the old lines under the slab. PEX is popular for this because it is flexible and needs fewer fittings. Fixr puts the high end of slab leak work at about $15,000 when all pipes are rerouted from under the slab to the attic.
  • Repairing under the slab means breaking or tunneling through concrete. Fixr's components: tunneling $900 to $2,000, breaking the slab $500 to $3,000, patching $250 to $800, and pipe repair $200 to $2,000.

Attic routes in Texas and Florida get hot, so insulation and correct support matter, and any plastic must be rated for the temperature and kept out of sunlight. For drains, PVC is standard for new work under slabs; existing cast iron can often be spot-repaired or lined rather than fully replaced. See the slab leak guide and sewer line repair and replacement.

Can a home inspector tell me what pipes I have?

Usually, for the pipes they can see. A home inspector will typically note visible supply and drain materials and obvious leaks or corrosion. But inspectors do not open walls, and InterNACHI's guidance says inspectors are not even required to note polybutylene, and should not test its strength. For a Florida insurance policy, the 4-point inspection is the document that records pipe type, and it must be signed by a Florida-licensed professional.

For pipes you cannot see, ask for:

  • A sewer camera inspection of the main drain, especially in pre-1975 homes with cast iron or clay.
  • A licensed plumber's evaluation if the home has PB, galvanized or a history of leaks.
  • The utility's service line inventory to see the material of the pipe from the meter to the house. See lead service lines.
  • Permit records from the city or county. A past repipe permit tells you the year and scope, which also answers the 4-point question about re-piping.

How to choose a provider

  • Write down the year your home was built and use the decade table as a starting guess.
  • Bring a flashlight, a coin and a magnet.
  • Inspect the supply pipes a foot or more from the water heater.
  • Check the stub-outs under every sink and behind the toilets.
  • Find the main shutoff and the pipe entering the house; do the scratch and magnet check.
  • Look in the attic for rerouted lines.
  • Read and photograph any printing on plastic pipe.
  • Check drain material at cleanouts and the laundry standpipe.
  • Look up permit history for past repipes.
  • For a Florida policy, get a 4-point inspection and keep a copy.
  • Ask a licensed plumber to confirm any polybutylene, Kitec, galvanized or lead finding.

Related plumbing guides

Plumbing by state and city

Questions people ask

Can I have more than one type of pipe in my house?

Yes, and most older homes do. A 1970s house might have a copper main, a PEX section added after a slab leak, CPVC to a remodeled bathroom, and cast iron drains with a PVC repair. Identify each run separately. For a Florida 4-point, the inspector marks every type present and whether the home is original, partially or completely re-piped.

What pipe was used in Texas homes in the 1980s?

Mostly copper or polybutylene for water supply, with cast iron giving way to PVC and ABS for drains. Polybutylene was widely installed in Texas; a proposed $750 million PB class settlement (Beeman v. Shell Oil, later rejected) was filed in Harris County in 1994. If your 1980s Texas home has gray flexible plastic stamped PB2110, it is polybutylene. Check under sinks and at the water heater.

Is copper pipe always the best choice?

Not always. Copper lasts a long time in many water conditions and resists UV, but it costs more ($2 to $8 per foot in materials per Bob Vila's 2023 guide versus $0.40 to $2 for PEX) and can develop pinhole leaks in aggressive water. PEX installs faster with fewer joints. The right choice depends on your water, budget and layout.

How do I tell copper from brass or bronze?

Copper pipe is a uniform penny color and smooth tube. Brass is more yellow and is used for valves and fittings, not long pipe runs. Older brass fixtures can contain more lead than current lead-free products, which is why EPA lists brass faucets among common lead sources in homes without lead service lines.

Is black plastic pipe always ABS?

On drains, black rigid plastic is almost always ABS. On water lines, black flexible pipe may be polyethylene, often used for yard service lines and irrigation, or occasionally black polybutylene. Read the printing on the pipe to be sure.

Does pipe type affect my home insurance in Texas?

Less directly than in Florida, since Texas has no standard 4-point inspection. But Texas policies commonly exclude damage from continuous or repeated leakage over time, and old or failing pipes raise the risk of exactly that kind of damage. Ask your insurer whether it asks about pipe type at application, and keep repipe records.

Should I replace my pipes just because of their age?

Not by age alone. Replace when there is a known failure pattern (polybutylene), repeated leaks, rust and low pressure (galvanized), lead, or when insurance requires it. Otherwise, inspect and monitor. A water pressure test, a leak check of your meter and a sewer camera inspection give a clearer picture than the calendar.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration