New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Fri, Nov 20, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Standby generator installation

How Often Should a Standby Generator Be Serviced, Exercised and Have Its Oil Changed?

A brand-neutral maintenance calendar for home standby generators, built from manufacturer manuals, with the extra steps Texas freezes and Florida salt air, heat and hurricanes demand.

Most home standby generators should exercise automatically once a week (some makers allow every two weeks), get a quick owner check monthly, and get professional service at least once a year. Oil and filter changes are usually due yearly or at a set number of run hours, whichever comes first; one manufacturer lists 100 to 150 hours depending on model. After a long outage, check oil every day the unit runs. Follow your own owner's manual, because the schedule there controls your warranty.

Key facts

  • Manufacturer A's residential manual says exercising the generator weekly or every two weeks is required to keep the engine and alternator in good condition (Manufacturer A TP-6804).
  • Manufacturer A's default unloaded exercise runs 20 minutes: about 10 minutes at reduced speed, then full-speed diagnostics and a cooldown (Manufacturer A TP-6804).
  • Manufacturer A 14 kW models: change oil yearly or every 100 hours, oil filter yearly or every 200 hours, spark plugs yearly or every 300 hours (Manufacturer A TP-6804).
  • Manufacturer A 20 kW models: change oil and filter yearly or every 150 hours (Manufacturer A TP-6804).
  • Manufacturer B's FAQ recommends service every 6 months by an authorized independent service dealer and says to check oil for every 24 hours of use during an outage (manufacturer site).
  • Manufacturer A recommends battery heaters where temperatures regularly fall below 32 F and a fuel regulator heater on 20 kW models where temperatures drop below 0 F (Manufacturer A TP-6804).
  • A 2026 cost guide lists generator maintenance visits at $186 to $568 (average $316) and battery replacement at $216 to $568 (Homeyou, 2026).
  • Federal hospital rules (42 CFR 482.15) require hospitals to follow NFPA 110 inspection, testing and maintenance requirements for emergency generators.
  • The Atlantic hurricane season runs June 1 to November 30 each year (National Weather Service).

What does a standby generator maintenance schedule look like?

A home standby generator is a car engine that sits outside for years and is expected to start the first time you need it, often in the worst weather of the year. That is why manufacturers build maintenance around two clocks at once: a calendar clock (weekly, monthly, quarterly, yearly) and an hour meter (run hours shown on the controller). Whichever limit you reach first is when the task is due.

The table below combines the published service schedules in Manufacturer A's residential owner manual (TP-6804) with Manufacturer B's public guidance. Other makers use similar intervals, but the numbers differ by engine. Your owner's manual is the document that counts for your warranty, so use this as a map and the manual as the rulebook.

TaskHow often (typical published interval)Who does it
Automatic exercise runWeekly (Manufacturer A allows weekly or every two weeks)Generator does it by itself
Look and listen during exercise: leaks, odd noise, vibration, debris near the exhaustWeeklyOwner
Check fuel supply level (propane tank gauge)WeeklyOwner
Check battery charger operationMonthlyOwner or dealer
Inspect flexible fuel lines and connectionsQuarterlyDealer, or owner visual check
Inspect enclosure interiorQuarterlyOwner visual, dealer cleaning
Oil changeYearly or 100 hours (Manufacturer A 14 kW), yearly or 150 hours (Manufacturer A 20 kW)Dealer or qualified owner
Oil filterYearly or 200 hours (14 kW), yearly or 150 hours (20 kW)Dealer or qualified owner
Air cleaner serviceYearly or by hours (150 inspect, 300 replace on Manufacturer A)Dealer or qualified owner
Spark plugsYearly or 300 hoursDealer or qualified owner
Clean battery and terminals, tighten wiring, inspect fuel piping, clean air ductsYearlyDealer
Brushes and collector ringYearly or 300 hours (Manufacturer A, dealer only)Dealer
Winding insulation resistance testEvery 3 years (Manufacturer A, dealer only)Dealer
Wire-cable insulation checkEvery 3 years or 500 hoursDealer

Manufacturer A's manual adds that units in extreme weather, long operating hours or dusty conditions need service more often than the table. In Texas and Florida, that covers a lot of homes: summer heat, coastal salt, pollen, lawn clippings and long hurricane outages all count.

How often does a generator exercise, and for how long?

"Exercising" means the generator starts by itself on a schedule, runs for a few minutes, checks itself and shuts down. It keeps oil spread through the engine, charges the battery, dries moisture out of the alternator, and gives the controller a chance to catch problems before an outage does.

Weekly vs every two weeks

Manufacturer A's manual states that exercising the generator weekly or every two weeks is required to keep the engine and alternator in good operating condition, and its controller can run the exercise at the same time and day each week. Many installers set the cycle weekly by default. Some newer controllers let the owner choose a longer interval. If your controller allows it, pick the schedule in your owner's manual. Going longer than the manual says can leave a weak battery or stuck part undiscovered.

How long the run lasts

Run length varies by design:

  • Manufacturer A unloaded cycle: 20 minutes total. Roughly 10 minutes at reduced speed to warm up, then a short full-speed period where the controller checks voltage and frequency, then a cooldown. Manufacturer A calls this its recommended default mode.
  • Manufacturer A unloaded full speed: 20 minutes at full speed, no load transferred.
  • Manufacturer A loaded exercise: transfers the house to the generator for 20 minutes, then back. Power to the building blinks off for up to 10 seconds during each transfer, so clocks and some electronics may reset.
  • Short test modes: Manufacturer D describes an "short test" mode that completes in 16 seconds, compared with what it calls standard 5 to 10 minute cycles. Manufacturer D says the short run is enough to start the engine and confirm it is ready while using less fuel and making less noise.

What if the power fails during an exercise?

Manufacturer A's manual explains that if utility power drops during an unloaded exercise, the transfer switch moves to generator power, the exercise ends, and the unit keeps running in AUTO for the length of the outage. You do not need to do anything.

Pick a sensible time

Set the exercise for a weekday daytime hour when someone is often home, so a person can hear a problem. Many Texas HOAs may set reasonable testing hours under Property Code 202.019, and many cities have noise rules, so a mid-morning slot avoids complaints. See generator noise rules and Texas HOA generator rules.

How often do you change standby generator oil, and what oil does it use?

The short answer: at least once a year, sooner if the hour meter says so. Manufacturer A lists yearly or every 100 hours for its 14 kW models and yearly or every 150 hours for its 20 kW models. Air-cooled home units run only a few hours a month on exercise, so most owners hit the yearly limit first, unless a long outage piles up hours.

The outage rule most owners miss

A week-long hurricane outage is about 168 hours of running. That alone can pass a 100 or 150 hour oil interval. Manufacturer B's FAQ says that for every 24 hours of use, the oil level should be checked and oil added if needed. Manufacturer A says to check the oil before each use and every 8 hours during extended operation, with the engine shut down for several minutes first. Plan for this before storm season:

  • Keep at least two or three quarts of the correct oil and a spare oil filter on hand.
  • Know where the dipstick and oil fill are (they are shown in the service views of your manual).
  • After a long outage ends, schedule an oil change even if the yearly visit is months away.

Low oil pressure shutdowns do not protect you from running low. Manufacturer A's manual notes that its low oil pressure shutdown is not a low oil level shutdown, so you still need to check the level.

Which oil

Use the exact grade in your manual. As one example, Manufacturer A's TP-6804 manual specifies 5W-30 or 10W-30 synthetic oil, API service class SG, SH or SJ, and says synthetic oil oxidizes and thickens less and leaves intake valves and pistons cleaner. Other engines may call for different grades, especially liquid-cooled units, so do not copy one brand's spec onto another.

Battery, spark plugs, air filter and valve checks

The starting battery is the single most common reason a standby generator fails to start. Manufacturer A's own troubleshooting table lists a weak or dead battery as the first cause when the generator does not crank or cranks but will not start.

Battery

  • Monthly: confirm the battery charger is working (Manufacturer A schedule). Many controllers show battery voltage and give a low-battery warning.
  • Yearly: remove corrosion, clean and dry the battery and rack, and clean and tighten the terminals.
  • Replacement: manufacturers do not all publish a fixed replacement age. Many dealers replace batteries on a set cycle or when a load test shows weakness. A 2026 cost guide lists battery replacement at $216 to $568 installed (Homeyou). Ask your dealer to load-test the battery at every visit rather than guessing.

Spark plugs and air cleaner

Manufacturer A lists spark plugs yearly or every 300 hours, and air cleaner service at 150 and 300 hours or yearly. Manufacturer B's site instructions warn that a dirty air filter or low oil can overheat the engine and that incorrect spark plug gaps can cause backfiring and incomplete combustion. Florida and Texas lawns produce a lot of grass, pollen and dust, so have the air filter looked at every visit.

Valve clearance

Some air-cooled engines call for a valve clearance check after a set number of hours. This is a dealer job. Ask your service tech whether your model's manual lists it and when it was last done.

Dealer-only items

Manufacturer A marks some tasks for an authorized dealer only, including brushes and collector ring checks (yearly or 300 hours) and a winding insulation test every three years. These need special tools and training.

Can We do my own generator maintenance without voiding the warranty?

Often yes, for simple owner-level tasks, but read your warranty before you open the enclosure. Three points matter:

  1. Federal law limits tie-in rules. The FTC's guide to the Magnuson-Moss Warranty Act says a warranty generally may not require you to use a particular brand of parts or service to keep coverage, unless the warrantor provides those parts or service free or gets an FTC waiver. A warrantor may still exclude damage caused by parts or service it did not provide.
  2. Your manual may assign some tasks to dealers. Manufacturer A's manual says to have an authorized dealer service the generator at the scheduled intervals for the life of the unit and marks certain tasks dealer-only. If a failure traces back to a task done wrong, the claim can be denied.
  3. Proof matters. Keep receipts for oil, filters and plugs, and a dated log of what you did. If the controller has a maintenance timer, reset it after each service so the record is clear.

A practical split many owners use: do the weekly look-and-listen, monthly battery charger check, fuel gauge checks and yard cleanup yourself. Leave oil changes during the warranty period, fuel system work and anything inside the electrical panels or controller to a qualified technician. Never work inside the unit with it in AUTO: Manufacturer A's manual says to press OFF, disconnect charger power and remove the battery negative lead first, because the generator can start by itself during an exercise or outage. See generator warranties explained.

What does a maintenance plan include and cost?

Most dealers sell a yearly or twice-yearly service agreement. Manufacturer B's FAQ recommends service every 6 months by an authorized independent service dealer and says many of its dealers offer annual maintenance contracts. A typical visit includes:

  • Oil and filter change, air filter and spark plug service as due
  • Battery load test and terminal cleaning
  • Inspection of fuel lines, regulator vents and connections, with a leak check
  • Controller software check and fault history review
  • Check of transfer switch operation, often with a simulated outage
  • Cleaning of the enclosure, louvers and air ducts, and removal of nests and debris
  • Written report and an updated maintenance record

Cost: Homeyou's 2026 cost guide lists backup generator maintenance visits at $186 to $568, averaging $316. Prices rise with liquid-cooled engines, travel distance and repair parts. Before signing a multi-year plan, ask:

  • How many visits per year, and is an outage-season visit guaranteed before June 1?
  • Are parts (oil, filters, plugs, battery) included or extra?
  • Is there priority dispatch during a declared emergency?
  • Does the plan include remote monitoring alerts, and who answers them?
  • Can I cancel, and is there a refund? In Texas, separately priced service contracts can fall under TDLR's service contract rules (Occupations Code ch. 1304), though agreements that cover only scheduled maintenance are exempt.

For hiring tips, see how to hire a generator installer.

Florida pre-hurricane season checklist (before June 1)

The Atlantic hurricane season runs June 1 to November 30, per the National Weather Service. Dealers in Miami, Tampa, Orlando and Jacksonville get booked solid once a storm forms, so schedule the yearly service in March, April or early May.

  1. Book the professional service visit and get the written report.
  2. Confirm the controller shows no active faults and the exercise schedule is set.
  3. Check the propane tank gauge and schedule a fill. A full tank before the season starts matters more than any other step for LP units. Florida residential propane averaged $5.167 per gallon in mid-November 2026 per EIA, so budget for it.
  4. Stock oil, an oil filter and the manual's spare parts for a long outage.
  5. Clear plants and debris. Manufacturer A says to keep plants and combustibles at least 4 feet beyond the exhaust end and furnace or similar air intakes at least 10 feet from the exhaust end.
  6. Make sure sprinklers, gutters and sump pump discharge do not spray or flood the unit. Manufacturer B's site instructions say excess moisture causes corrosion and shortens life.
  7. Check that the remote monitoring app is connected, alerts go to your current phone, and a backup contact is listed.
  8. Test your carbon monoxide alarms. Manufacturer B's instructions recommend CO detectors on each level of the home next to the generator.
  9. If you live where storm surge is a risk, review your plan with the flood and wind anchoring guide.

Salt air and humidity

Coastal units in Miami-Dade, Broward, the Tampa Bay area and Jacksonville Beach see faster corrosion of terminals, hinges and fasteners. Ask the tech to clean and protect battery terminals, look for rust on the enclosure base and hardware, and check wiring connections each visit. Some enclosures are built for seaside use: Manufacturer A describes its composite enclosure as corrosion-proof even in harsh seaside environments. Rinse salt spray off the outside with a gentle hose only if your manual allows it, and never spray water into the air inlets.

Texas freeze checklist and cold-weather kits

Winter Storm Uri in February 2021 left more than 4.5 million people in Texas without power, some for as long as four days in below-freezing weather, according to the FERC-NERC report. Texas DSHS confirmed 246 storm-related deaths, 158 from hypothermia and 19 from carbon monoxide poisoning. A standby generator that will not start in a freeze is exactly the failure you are paying to avoid.

Do you need a cold-weather kit?

Manufacturer A recommends its cold weather heater kits where the temperature drops below 32 F. The kit includes a battery heater, breather tube heater, fuel regulator heater and oil heater. Its battery heater turns on at 60 to 65 F and off at 80 F, and Manufacturer A recommends battery heaters for regions where temperatures regularly fall below 32 F. A carburetor heater is recommended below 32 F to prevent icing, and on 20 kW models a fuel regulator heater is recommended below 0 F. All of these need a continuous AC power source.

In practice: Amarillo, Lubbock and the Panhandle see regular hard freezes, so a cold kit is common there. Dallas-Fort Worth, Austin and San Antonio get occasional hard freezes, so many owners add at least a battery heater. Houston and the coast rarely need one, but Uri showed that rare events happen. Ask your dealer what your model needs.

Before the first freeze (November)

  1. Load-test the battery. Cold weather cuts starting power.
  2. Confirm any heaters are plugged in and working.
  3. Check the propane tank. Propane prices can rise early in the heating season, the Railroad Commission notes, and a larger tank helps you ride out supply shortages. Texas residential propane averaged $3.209 per gallon in mid-November 2026 per EIA.
  4. Make sure snow and ice cannot block the air intake or exhaust. Keep the area around the unit clear.
  5. For natural gas units, remember that Uri also cut gas supply in places. A natural gas generator depends on the gas utility staying up.

More on outage planning: Texas grid outages and generators.

How do I keep fire ants, rodents and snakes out of a generator?

Generator enclosures are warm, dry and quiet most of the time, which makes them attractive to fire ants, mice, rats, wasps, lizards and snakes across Texas and Florida. Fire ants are drawn to electrical equipment and can pack mounds into contacts and control boxes. Rodents chew wiring insulation.

  • Look inside each quarter. Manufacturer A's schedule calls for a quarterly inspection of the sound enclosure interior. With the unit OFF and the battery disconnected per your manual, look for mounds, nests, droppings and chewed wires.
  • Treat around the pad, not inside. Use ant bait around the pad perimeter. Do not spray liquids or dust into the enclosure, controller or air inlets. Ask your dealer about approved methods for your model.
  • Keep the pad clear. Remove mulch, woodpiles and tall grass next to the unit. Manufacturer A says not to set the pad on grass, wood or other combustibles and to keep plants clear of the exhaust end.
  • Seal conduit openings. Ask the installer to seal gaps where conduit and fuel lines enter.
  • Get chewed wiring repaired by a pro. Damaged control wiring can stop the transfer switch from working. Pest damage is usually excluded from warranties.

How remote monitoring helps (and its limits)

Most current home standby units can report their status to an app. Some makers include remote monitoring with every home standby generator they offer. One manufacturer's controller has an Ethernet connection for its generator management system and built-in maintenance reminders. These tools tell you:

  • Whether the last exercise ran and passed
  • Warnings such as low battery, low fuel (with a compatible tank monitor) or a service due
  • Fault shutdowns and the code to give your dealer
  • Run hours, so you know when an outage pushed you past an oil interval

Limits: the app needs internet. During a wide outage, your router and the cellular network may also be down, unless they are on generator power. Some systems offer a cellular option. Monitoring also does not replace an oil change or a battery test; it only tells you something is wrong. Make sure alerts go to someone who can act if you travel during storm season, and that your dealer is allowed to see them if your plan includes that.

What does a load bank test do, and who needs one?

A load bank is a portable machine that places an artificial electrical load on a generator, so a technician can see whether the unit can carry its rated output for a sustained period without overheating, dropping voltage or losing frequency. Weekly exercise runs, especially unloaded ones, do not prove that.

  • Homes: load bank testing is not a routine requirement for most residential air-cooled units. It can make sense after major repairs, if a unit struggled during an outage, or before relying on a generator for medical equipment. See generators for medical needs.
  • Commercial and health care: emergency systems are governed by NFPA 110 (Standard for Emergency and Standby Power Systems). Federal hospital rules at 42 CFR 482.15 require hospitals to implement the generator inspection, testing and maintenance requirements in the Health Care Facilities Code, NFPA 110 and the Life Safety Code, and the regulation incorporates the 2010 edition of NFPA 110 by reference. Florida rule 5J-20.002 adopts the 2025 edition of NFPA 110 for its LP gas standards. NFPA 110 sets specific monthly and periodic load test requirements; the standard is sold by NFPA, so facility managers should work from the edition their authority adopts rather than secondhand summaries.

Florida nursing homes and assisted living facilities have their own state generator and fuel rules. See the Florida nursing home and ALF generator rule and commercial generator codes.

What to do after an outage

  1. When utility power returns, let the transfer switch move back on its own and the engine finish its cooldown. Do not shut it off mid-cycle unless there is an emergency.
  2. Note the hour meter reading. Compare it with your manual's oil and filter intervals.
  3. Check the oil level after the engine has been off a few minutes.
  4. Check the propane tank level and order a refill. Ask your supplier for a leak check if the tank was disturbed by wind or flooding.
  5. Walk around the unit: debris, flood water lines, damaged fence panels or a shifted pad all need a dealer visit before the next storm.
  6. If the unit sat in standing water, do not run it until a technician inspects it. Manufacturer B's instructions say the generator should not operate in or be subjected to standing water.
  7. Book service if the unit ran more than a few days or logged any faults.

For problems, see generator troubleshooting and repair and generator lifespan and replacement.

How to choose a provider

  • Find your owner's manual and copy its service schedule onto one page.
  • Confirm the exercise runs weekly (or as the manual says) at a daytime hour.
  • Watch and listen to one exercise a month: leaks, rattles, smoke, warning lights.
  • Check the battery charger monthly and the propane gauge weekly.
  • Book professional service at least yearly; Florida owners before June 1, Texas owners before the first freeze.
  • Change oil yearly or at the manual's hour limit, whichever comes first.
  • Check oil every 24 hours of run time during long outages; keep spare oil and a filter.
  • Ask about a battery heater or cold kit if you live where it often freezes.
  • Inspect inside the enclosure quarterly for ants, nests and chewed wires (unit OFF, battery disconnected).
  • Keep plants 4 feet from the exhaust end and air intakes 10 feet away, per Manufacturer A's manual.
  • Keep a dated log and receipts for every service for warranty claims.
  • Test CO alarms on every level of the home.

Related standby generator installation guides

Standby generator installation by state and city

Questions people ask

How often should a standby generator be serviced?

At least once a year by a qualified technician, plus weekly automatic exercise and quick monthly owner checks. Manufacturer B's FAQ recommends professional service every 6 months. Units in extreme heat, cold, dust or salt air, or units that ran through a long outage, need service more often. Manufacturer A's manual says these conditions call for more frequent service than its standard schedule.

Should my generator exercise weekly or every two weeks?

Follow your manual. Manufacturer A's manual says weekly or every two weeks is required to keep the engine and alternator in good condition. Weekly is the most common factory default. A longer gap saves a little fuel and noise but gives a weak battery or fault more time to go unnoticed before a storm.

How long should a generator exercise run?

It depends on the controller. Manufacturer A's default unloaded exercise is 20 minutes, including warm-up, full-speed diagnostics and cooldown. Manufacturer D describes a 16-second short test mode and says standard cycles run 5 to 10 minutes. You usually cannot shorten a cycle below what the controller offers, and you should not try.

How often should I change the oil in my home standby generator?

Usually once a year or at the hour limit in your manual, whichever comes first. Manufacturer A lists yearly or 100 hours for its 14 kW models and yearly or 150 hours for its 20 kW models. A long outage can use up that many hours in a week, so change the oil after any extended run.

What should We do if the generator runs for days during a hurricane?

Check the oil level about once a day. Manufacturer B says to check for every 24 hours of use and add oil if needed. Shut the unit down briefly to do it safely, following your manual, and keep spare oil on hand. Watch the propane gauge and call your supplier early, because delivery trucks get busy after storms.

How long does a generator battery last?

Manufacturers do not all publish a fixed life. Heat shortens battery life, which matters in Texas and Florida. Have the battery load-tested at every service visit and replace it when it tests weak. A 2026 cost guide lists battery replacement at $216 to $568 installed (Homeyou).

Will doing my own oil change void the warranty?

Not automatically. Federal warranty law generally bars warranties from requiring a specific brand of parts or service unless it is provided free. But the warrantor can deny claims for damage caused by improper work, and some manuals reserve tasks for authorized dealers. Use the specified oil and filter, keep receipts and a log, and read your warranty first.

Do I need a cold-weather kit in Texas?

It depends on where you live and your model. Manufacturer A recommends its cold weather kit where temperatures drop below 32 F and a battery heater where they regularly do. Panhandle and North Texas owners commonly add one. Many Central Texas owners add at least a battery heater after Winter Storm Uri. Ask your dealer for your model's recommendation.

How much does generator maintenance cost?

Homeyou's 2026 cost guide lists maintenance visits at $186 to $568, averaging $316. Liquid-cooled units, repairs, parts and long travel distances cost more. Multi-visit service plans vary widely, so compare what each one includes, such as parts, battery tests and priority storm dispatch.

Can I spray the generator with a hose to clean it?

Only the outside, gently, and only if your manual allows it. Never spray into air inlets, louvers, the controller or exhaust. Manufacturer B's site instructions warn that sprinklers and water spray can damage the unit and that excess moisture causes corrosion. Turn the unit to OFF before any cleaning.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration