New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Standby generator installation

Generators in Flood Zones and Hurricane Winds: Elevation, Anchoring and Storm Prep

What Florida code, FEMA guidance and manufacturers say about raising, anchoring and protecting a standby generator, and what to do if one floods.

In a Florida flood hazard area, the 8th Edition Florida Building Code requires a permanently installed standby generator to sit at or above the required flood elevation, or be designed to resist flooding. Texas rules come from your local floodplain administrator. FEMA says a home generator, transfer switch and emergency panel should be elevated above the flood protection level. Never run a submerged generator.

Key facts

  • The Florida Division of Emergency Management's 8th Edition Florida Building Code (2023) flood compilation lists residential mechanical section M1905.2.2, which requires permanently installed stand-by generators in flood hazard areas to be located or installed in accordance with Residential section R322.1.6.
  • Florida Building Code Residential R322.1.6 requires electrical systems and other service equipment to be at or above the elevation required by R322.2 or R322.3, with an exception for equipment designed to prevent water entry and resist flood loads, including buoyancy, under ASCE 24.
  • Florida Building Code Residential R322.2.1 sets the lowest floor in most flood hazard areas at the base flood elevation plus 1 foot, or the design flood elevation, whichever is higher.
  • FEMA P-348 (Edition 2, Feb. 2017) says a home's standby generator, transfer switch and normal/emergency panel should be elevated above the flood protection elevation, with the feeder and control wiring elevated or suitable for submerged installations.
  • FEMA P-348 says equipment on outdoor platforms and pedestals must be anchored to resist applicable wind loads, and in coastal Zone V pedestals must not be sited under or immediately adjacent to buildings.
  • One manufacturer's 20 kW spec sheet rates its sound-attenuated generator enclosure for winds up to 150 mph (241 km/h); that rating is for the enclosure, not the pad or anchors.
  • Miami-Dade County's generator permit guide for unincorporated areas requires a generator anchoring detail and pad size, thickness and reinforcement under Florida Building Code section 1818.1.
  • A manufacturer's support article says not to start or operate a generator that has been submerged, and to have an authorized service dealer clean, dry and inspect it first.
  • NEMA's guidance says ocean water and salt spray can be particularly damaging to electrical equipment and that replacement will often be necessary after flooding.
  • FEMA's FloodSmart site says most homeowners insurance does not cover flood damage.

Short answer: who decides how high and how strong?

Four things decide whether a generator is protected from water and wind: the building code and floodplain rules where you live, federal flood guidance, the manufacturer's installation instructions, and your insurance policy. They do not always agree, and the gaps matter. In a mapped Florida flood hazard area, the Florida Building Code (8th Edition, 2023) says a permanently installed residential standby generator must be located or installed so that it sits at or above the required flood elevation, or is designed to keep water out and resist flood forces, including buoyancy. Texas has no single statewide equivalent that we could find, so the answer comes from your city or county floodplain administrator. The federal guide FEMA P-348 says plainly that a home's standby generator, transfer switch and emergency panel should be elevated above the flood protection level.

This guide explains each rulebook, what "elevation" means in practice, how anchoring and wind ratings work, what to do before and after a storm, and what insurance does and does not say about a flooded generator. It is general information, not engineering or legal advice. Confirm your flood zone and your local rules with your floodplain administrator before you buy.

Does my generator need to be elevated in a flood zone?

Florida: the Florida Building Code

The Florida Division of Emergency Management's compilation of the flood provisions in the 8th Edition Florida Building Code (2023) lists a new residential mechanical section, M1905.2.2: in flood hazard areas set by Table R301.2(1), permanently installed stand-by generators must be located or installed in accordance with Residential section R322.1.6. That section requires electrical systems, equipment and components, and other service equipment to sit at or above the elevation required in R322.2 (flood hazard areas, including A zones) or R322.3 (coastal high hazard areas). Two details matter:

  • The reference elevation includes a foot of extra height. For buildings in flood hazard areas other than Coastal A zones, R322.2.1 sets the lowest floor at the base flood elevation (BFE) plus 1 foot, or the design flood elevation, whichever is higher. The generator rule points to the same elevation.
  • Replacement counts. R322.1.6 says replacement of exterior equipment and exterior appliances damaged by flood must meet the requirement, and so must equipment replaced as part of a substantial improvement.

There is an exception. Equipment may sit below the required elevation if it is designed and installed to prevent water from entering or accumulating within the components and to resist hydrostatic and hydrodynamic loads, including buoyancy, during flooding up to the required elevation, following ASCE 24, the national flood-resistant design standard. For a typical pre-packaged home generator, an engineer would have to show how that is met, so in practice elevating is the usual route. R322.1.6 also bars mounting equipment on walls designed to break away under flood loads. For new essential electrical systems in hospitals and similar care facilities (Group I-2 occupancies), Building section 2702.1.8 requires new generators to be located and installed under ASCE 24, and temporary generator hookups to be at or above the ASCE 24 elevation.

Miami-Dade's Product Approval page notes that the Ninth Edition of the Florida Building Code becomes effective on 12/31/2026. Ask your building department which edition applies to your permit date, because section numbers and details can change.

Texas: local floodplain rules, and a 2025 state law to watch

We did not find a Texas statewide rule that sets a generator elevation. Texas floodplain rules are adopted by cities and counties that participate in the National Flood Insurance Program, so the rule that applies to you is the one your floodplain administrator enforces. Houston is a useful example. After 2018 amendments to its Chapter 19, new construction and substantial improvements in the 500-year floodplain must be built 2 feet above the 500-year flood elevation, and the Houston Permitting Center's Oct. 26, 2018 guidance describes the current regulatory elevation as the 500-year elevation plus 2 feet. That guidance, written about air conditioning systems, says Chapter 19 and the NFIP only require equipment elevation to those elevations when the value of the work exceeds 50 percent of the structure, while multi-family and commercial equipment in the regulated floodplain must be elevated to the regulatory elevation. We did not find a published Houston rule specific to residential standby generators.

A second issue: Senate Bill 1252 (effective Sept. 1, 2025) bars Texas cities from adopting or enforcing ordinances or measures that regulate the installation or inspection of a "residential energy backup system" of no more than 50 kW. We found no authoritative guidance on how that law interacts with local floodplain elevation rules for a generator. Ask your floodplain administrator and your installer how the city applies its flood rules to your project, and ask an attorney if you get conflicting answers. Municipally owned utilities such as Austin Energy and CPS Energy keep their own authority.

How high should a generator be raised above flood level?

There are two honest answers: the legal minimum and the best practice.

SourceWhat it says
Florida Building Code (8th Ed., 2023), R322.1.6, R322.2.1At or above the required flood elevation, which for most flood hazard areas is the BFE plus 1 foot or the design flood elevation, whichever is higher.
FEMA P-348 (Edition 2, Feb. 2017)If the home has a standby generator, it, along with the transfer switch and the normal/emergency panel, should be elevated above the flood protection elevation. The feeder connecting the generator and all control wiring should be elevated or suitable for submerged installations.
FEMA P-348, "best practice" noteWhen a building is elevated higher than the minimum required level, the equipment serving it should be elevated at least to the same height. FEMA says this both protects the equipment and gives access to the best available NFIP insurance rates.
Manufacturer installation instructionsChoose high ground where water will not rise and flood the unit; the unit must not operate in or be subjected to standing water. Keep roof runoff, sprinklers and sump discharge from flooding or spraying the enclosure.
Houston Permitting Center (Oct. 26, 2018)The regulatory elevation is the 500-year flood elevation plus 2 feet. (Guidance written for air conditioning replacement; no generator-specific Houston rule found.)

FEMA defines the "flood protection level" as the level of the flood used in design of buildings, including any extra height added by local rules or by the owner. For a Florida home that must be built at BFE plus 1 foot, that is the number to use. The surest way to know your number is an elevation certificate or the flood elevation shown on your permit file. Your floodplain administrator can tell you your zone and BFE.

Ask the installer to put the target elevation in the plans as a number, in feet above a named datum, not as "high enough." If your lowest floor is above the minimum, FEMA's best-practice note suggests matching the equipment to your actual finished floor.

How elevation is done: pads, platforms, pedestals and roofs

FEMA P-348 describes four ways to raise exterior equipment: platforms (free-standing and self-supporting, or cantilevered and knee-braced from the building), masonry pedestals, hanging from walls or framing, or placing on a roof. A few rules from that guide apply directly to generators:

  • Platforms and pedestals used to elevate equipment must resist flood loads and other applicable loads. Equipment on outdoor platforms must be anchored to resist applicable wind loads, and in regions with significant seismic risk to resist seismic loads.
  • In coastal Zone V on flood maps, pedestals must not be sited under or immediately adjacent to buildings because they could obstruct the free passage of floodwater and waves.
  • Protection must also be provided for anything running from the ground to the building, including gas and fuel lines and underground electric service. A generator on a tall stand with a gas line that fails in a surge has not solved the problem.
  • Above-ground fuel tanks in flood hazard areas must be designed to resist flotation, collapse and lateral movement. Anchoring straps and cables should resist corrosion and withstand buoyancy forces when the tank is empty, and fill openings and vents should sit above the flood protection level or be designed to keep floodwater out. In Zone V, tanks cannot be under elevated buildings or attached to the building below the lowest floor. See propane tank rules.

One generator manufacturer's instruction sheet says that where a unit must go on a roof, platform, deck or other supporting structure, it must follow NFPA 37 section 4.1.3, with a noncombustible surface beneath and beyond it for at least 12 inches, and that you should contact the local building or fire department for approved materials. Raising the unit also changes other things: service technicians need safe access, exhaust still must stay clear of openings, an elevated unit may be more visible (so an HOA may care), and the fuel and electric runs get longer. See placement and clearances.

Can a standby generator survive a hurricane? Wind ratings and anchoring

The best published evidence is the manufacturer rating, and it is narrower than people assume. One manufacturer's spec sheet for a 20 kW air-cooled home standby model says its sound-attenuated enclosure is built to withstand winds up to 150 mph (241 km/h). That is a rating for the enclosure. It does not say the pad, the anchors, the fuel line or the attached equipment would survive 150 mph winds with flying debris. We found no neutral, post-storm survey of how standby generators performed in Texas or Florida hurricanes, so any claim that these units "always survive" has no source here.

What the installation instructions require

  • One manufacturer's instruction sheet says the unit is typically approved on pea gravel, crushed stone or a concrete pad and tells the installer to verify that any base pad meets or exceeds local codes and requirements for wind ratings. It also says concrete pads must be sized under national, state or local building codes, and the unit must be level within 0.5 inch.
  • That sheet requires at least 5 feet of clearance above the generator for overhangs, and says removable fence panels should be 3 feet away, which also keeps trees, awnings and roof overhangs from becoming impact or fire hazards.
  • Another manufacturer ships its unit on an engineered composite pad and says to place it on gravel with a weed barrier or on a concrete pad, never directly on grass or wood.

What local permits require

Wind and anchoring details are a permit item in coastal Florida. Miami-Dade County's generator permit guide for unincorporated areas lists, under structural requirements, soil bearing capacity, the generator pad's size, thickness and reinforcement, and a generator anchoring detail, citing Florida Building Code section 1818.1. A Palm Beach County town's checklist asks for a concrete slab drawing with anchor and fastening detail (or product approval for a prefabricated slab), and its inspection bulletin says that where the manufacturer gives no pad details the slab must be at least 4 inches thick, 4 inches larger on all sides than the unit, with at least #3 rebar at no more than 12 inches on center. Engineered slabs must carry the engineer's seal. If you are in an incorporated city, the city's own building department rules apply. Miami-Dade County also administers a High Velocity Hurricane Zone chapter of the Florida Building Code and issues its own Notices of Acceptance for building products (see its Product Approval Notices page); ask your building department whether any item on your job needs one.

The same guide notes zoning limits for generators in unincorporated Miami-Dade: units fueled by propane or natural gas not exceeding 5 feet in height from finished grade are an accessory use in certain residential districts with set setbacks, for example 5 feet from the rear lot line and 3 feet from the interior side line in RU districts. Always verify with your local zoning office.

Texas coastal homes in the 14 first-tier counties (including Galveston, Jefferson, Nueces and Brazoria) may carry wind and hail coverage through the Texas Windstorm Insurance Association, which is governed by Insurance Code chapter 2210. Ask your insurer or agent how a generator is treated and what the wind and hail deductible is. See the insurance section below.

Should I turn my generator off before a hurricane? Should I cover it?

We did not find a manufacturer instruction telling owners to switch a standby generator off ahead of a hurricane. A standby generator is designed to start automatically when utility power fails. What the sources do say is useful:

  • A manufacturer's support article says the unit must not operate in or be subjected to standing water, and not to start or operate a generator that has been submerged.
  • The same article says to check for water intrusion after severe weather, noting heavy rain can erode a raised slab or cause more pooling than expected, and that if the unit did not start in Auto and you see pooling in or around the housing, avoid running it and call a local service dealer.
  • The enclosure is designed for weather. Nothing we reviewed recommends covering a running standby generator with a tarp or box; blocking the air inlets and exhaust would stop the cooling and exhaust it needs, and a manufacturer prestart list calls for clean, unobstructed air inlets and an unobstructed exhaust outlet. See carbon monoxide safety.

If you expect floodwater to reach the unit, ask your service dealer before the storm what they recommend for your model. If the house itself floods, one manufacturer says a certified electrician should inspect before the generator runs or utility power returns.

Before the storm: a prep checklist for owners

  1. Confirm your flood zone and BFE. Use the FEMA Flood Map Service Center or ask your floodplain administrator. Write down the elevation of your generator pad.
  2. Exercise it. One manufacturer's manual says exercising weekly or every two weeks is required to keep the engine and alternator in good condition. Check the controller for faults.
  3. Check fuel. A manufacturer's schedule lists weekly checks of the main tank supply level and for leaks, and quarterly inspection of flexible fuel lines. For propane, confirm the tank level. See runtime and fuel use.
  4. Check the battery and the maintenance date. Monthly battery charger checks are on the same schedule. See maintenance schedule.
  5. Clear the area. Remove loose items, branches and debris. Keep shrubs and combustibles at least 4 feet beyond the exhaust end (one manufacturer's rule).
  6. Test your carbon monoxide detectors. A manufacturer's instruction sheet recommends CO detectors on each level of a structure adjacent to the generator and warns that smoke alarms do not detect CO. After Hurricane Irma, Florida's health department found that generator use caused 97.5 percent of CO exposures it identified in a study, and 62.8 percent of 516 generator-related exposures involved homes without a CO detector.
  7. Photograph the installation (pad, anchors, labels, serial number) for insurance and service.
  8. Know your shutoffs for gas, the generator breaker and the main breaker, and where the manual is.
  9. Keep the dealer's number and your warranty paperwork.

After the storm: what to do if your generator was flooded

A flooded generator is not a "dry it out and try it" problem. The National Electrical Manufacturers Association's guidance on water-damaged electrical equipment says equipment exposed to water can be extremely dangerous if re-energized without proper reconditioning or replacement. Moisture reduces insulation integrity, debris lodges in components, and floodwater contaminated with chemicals, sewage or oil can damage equipment. It adds that ocean water and salt spray can be particularly damaging because of the corrosive and conductive nature of the salt residue. It says the original manufacturer should be contacted, and that in many cases replacement will be necessary. Do not attempt to recondition equipment without consulting the manufacturer, because improper cleaning agents can add damage.

Steps

  1. Stay safe. Do not touch the unit, transfer switch or panel if you may be standing in water. If the controller or wiring was under water, treat it as energized.
  2. Do not start it. A manufacturer's support article says: "DO NOT start or operate generator if it has been submerged in water." An authorized service dealer should clean, dry and inspect it before any use.
  3. Shut off the gas supply if the gas meter, propane tank or piping was affected, and call the gas utility or LP-gas company. Fuel tanks can be displaced by flood forces (see FEMA P-348 on tanks).
  4. Have the whole house electrical system checked. If the house flooded, one manufacturer says a certified electrician should inspect before the generator runs or utility power returns. In Florida, FPL says homeowners own and are responsible for electrical equipment attached to the house (service stack, attachment hardware, riser and meter box) and must repair storm damage to it before FPL can restore service.
  5. Document everything. Photograph the high-water mark, the unit, the pad and the serial plate before anything is moved.
  6. Call your insurance agent and, if you have one, your flood insurance carrier (see below), and ask the dealer for a written inspection or replacement estimate.
  7. Replace, do not reuse, damaged control and electrical parts as the manufacturer directs. A dealer may be able to replace the controller, wiring, transfer switch and fuel components rather than the whole unit, but that is the dealer's and manufacturer's decision.

Salt water and storm surge

Surge pushes salt water inland in Gulf coast and Atlantic storms. NEMA says salt residue is corrosive and conductive. Manufacturer guidance on siting says excess moisture can cause corrosion and decrease unit life, and it recommends keeping irrigation and downspout water off the enclosure. For a unit that has been in salt water, plan on manufacturer-directed replacement of affected components, not cleaning, and expect the warranty to turn on whether the manufacturer treats the event as covered. See warranty explained and lifespan and replacement.

Will insurance cover a flooded generator?

General information only; read your own policies and ask your agent in writing.

  • Homeowners policies. FEMA's FloodSmart site says most homeowners insurance does not cover flood damage. Wind damage may be a separate matter with its own deductible, so ask how wind and hail are handled in your policy.
  • NFIP flood insurance. The Standard Flood Insurance Policy, Dwelling Form (44 CFR part 61, Appendix A(1)) lists covered building property in detail. It does not name generators. It covers fuel tanks and the fuel in them as one of the listed items for property below the lowest elevated floor of an elevated post-FIRM building in certain zones (and in basements in any zone), and it lists central air conditioners, electrical junction and circuit breaker boxes, outlets, furnaces and others. Separately, its list of property not covered includes "containers, including related equipment, such as, but not limited to, tanks containing gases or liquids." Whether a ground-mounted generator and its propane tank are building property, personal property or not covered is not answered by the policy text itself. Ask your agent, and ask the adjuster to put the answer in writing before a loss.
  • Elevation helps insurance too. FEMA P-348 says elevating equipment to match the building's elevated level allows access to the best available NFIP rates.
  • Warranty. Generator warranties typically exclude floods and storms; see the warranty guide in this series.

When you file a claim, document the damage before cleanup and keep the dealer's report. For disputes, contact your state insurance regulator: the Texas Department of Insurance or the Florida Office of Insurance Regulation. A licensed public adjuster may help in Florida, but verify the license first.

Texas and Florida storm notes

  • Houston. NWS Corpus Christi reports that Cedar Bayou in Houston received a storm total of 51.88 inches of rain from Hurricane Harvey, a new North American record. Hurricane Beryl (July 2024) disrupted electric service for 2.7 million customers, including 2.2 million CenterPoint customers, per the Public Utility Commission of Texas. Together they show why Houston owners worry about both flooding and long outages. See the Houston page.
  • Gulf Coast (Galveston, Corpus Christi, Beaumont and Port Arthur). These areas are in or near the 14 first-tier coastal counties covered by the Texas Windstorm Insurance Association. FEMA P-348 includes a photograph of an elevated generator and switchgear at a Galveston medical center. Ask your floodplain administrator about local elevation rules. See the Texas hub.
  • Dallas, San Antonio, Austin. Surge is not the issue inland, but drainage is: a manufacturer's site guidance says to keep roof runoff, sprinklers and sump discharge off the unit. See the Dallas, San Antonio and Austin pages.
  • Miami. Miami-Dade requires an anchoring detail and pad design with generator permits in unincorporated areas, and a separate High Velocity Hurricane Zone chapter applies to product approvals. See the Miami page.
  • Tampa, Orlando, Jacksonville. After Hurricane Milton, Duke Energy Florida said outages fell from over 1 million to about 3,000 by Oct. 17, 2024. FPL, for its part, says you own the equipment attached to your house. See the Tampa, Orlando and Jacksonville pages.
  • Condos and multifamily. Elevating, anchoring and fuel storage on common property usually needs board approval and engineering. See condo and multifamily generators and, for care facilities, Florida nursing home and ALF rules.

How to choose a provider

  • Look up your flood zone and base flood elevation, and write it down.
  • Ask your building department which edition of the Florida Building Code applies and whether a local rule sets generator elevation (Texas: ask the floodplain administrator).
  • Have the plans state the pad or platform elevation as a number above a named datum.
  • Confirm pad size, reinforcement and anchoring detail meet local code and the manufacturer's wind requirements.
  • Raise fuel lines, controls and the transfer switch to match the generator, or use submersible-rated components.
  • Anchor any propane tank against flotation and keep fill and vent points above the flood level.
  • Exercise the generator and check fuel, battery and fault codes before storm season.
  • Install and test CO detectors in the house.
  • Photograph the finished installation and serial plate for insurance.
  • Ask your agent in writing how flood, wind and a generator are treated.
  • After any flooding, do not start the unit; call a service dealer and an electrician.
  • Keep the dealer's phone number and warranty papers where you can find them without power.

Related standby generator installation guides

Standby generator installation by state and city

Questions people ask

Does my generator need to be elevated in a flood zone?

In a Florida flood hazard area, yes unless it is designed to resist flooding: the 8th Edition Florida Building Code requires permanently installed standby generators to meet section R322.1.6, which puts equipment at or above the required flood elevation. We found no statewide Texas rule, so ask your city or county floodplain administrator. FEMA's P-348 guide says a home's standby generator, switch and emergency panel should be elevated above the flood protection level.

How high should a generator be raised above flood level?

Meet or exceed the required flood elevation. For most Florida flood hazard areas the building code's reference is the base flood elevation plus 1 foot, or the design flood elevation if higher. FEMA's best practice is to match the equipment to the elevated building height when the home is built above the minimum. Put the target elevation in the plans as a number.

Can a standby generator survive a hurricane?

A manufacturer spec sheet rates one 20 kW unit's enclosure for winds up to 150 mph, but that is an enclosure rating, not a guarantee for the pad, anchors, fuel line or flying debris. We found no neutral post-storm survey. Proper siting, anchoring to local code and elevation above flood level are the controllable factors.

How is a generator anchored for wind?

It depends on the jurisdiction and model. Manufacturer instructions say to verify any pad meets or exceeds local requirements for wind ratings. Miami-Dade's permit guide for unincorporated areas requires pad size, thickness, reinforcement and an anchoring detail, and one Palm Beach County town sets a minimum slab thickness and rebar spacing where the manufacturer gives none. Your permit plans should show it.

Should I turn off my generator before a hurricane hits?

We found no manufacturer instruction to switch a standby generator off before a storm; it is designed to start automatically when utility power fails. Do not let it operate in standing water, and do not run a unit that has been submerged. If floodwater is expected to reach it, ask your service dealer for model-specific advice in advance.

What do We do if my generator was flooded?

Do not start it. A manufacturer's support article says not to operate a generator that has been submerged and to have an authorized service dealer clean, dry and inspect it, and to have a certified electrician check the home first if it flooded. NEMA says water-damaged electrical equipment can be dangerous if re-energized and that replacement is often necessary.

Will insurance cover a flooded generator?

It depends. FEMA's FloodSmart says most homeowners policies do not cover flood. The NFIP dwelling form does not name generators, covers fuel tanks only in specific situations, and excludes containers and related equipment such as tanks holding gases or liquids. Ask your agent in writing how a ground-mounted generator and propane tank are treated before a loss.

Can storm surge salt water ruin a generator?

Yes. NEMA says ocean water and salt spray can be particularly damaging because of the corrosive and conductive nature of the salt residue, and that replacement is often needed for electrical equipment exposed to flooding. A manufacturer's site guidance also warns that excess moisture causes corrosion and decreases life expectancy. Have a dealer assess the unit before any use.

Should I cover my generator during a storm?

No source we reviewed recommends covering a standby generator. The enclosure is made for weather, and a prestart checklist calls for clean air inlets and an unobstructed exhaust outlet. Covering a running unit could block cooling air and exhaust. Instead, site it above flood level, keep gutters and sprinklers from spraying it, and clear debris before the storm.

Is a generator in a flood zone covered by the manufacturer warranty after a flood?

Usually not. Manufacturer warranties typically cover defects in materials and workmanship, and common exclusions include floods and storm events; read your warranty for the exact wording. The warranty guide in this series explains the usual exclusions. Ask the dealer to describe in writing what the manufacturer considers covered before you need a claim.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration