Local Guide · Standby generator installation
Where Can a Standby Generator Go? NFPA 37, Manufacturer Clearances and Window Setbacks
Four separate rulebooks decide where a standby generator can sit: the NFPA 37 fire standard, the manufacturer's manual, your local building and zoning code, and your HOA. Here is how each one works, with the real distances from the documents.
As a starting point, NFPA 37 keeps an engine generator at least 5 feet from openings in a building and from combustible walls. Units tested by Southwest Research Institute can sit 18 inches from a combustible wall at the back, with 3 feet at the front and ends, but windows, doors and vents still need the full locally adopted distance. Your manufacturer's manual, city code and HOA can add more.
Key facts
- Manufacturer B's site instructions summarize NFPA 37 as requiring an engine generator to be at least 5 ft (1.5 m) from an opening in a structure or from a structure with combustible walls.
- Based on Southwest Research Institute fire testing and NFPA 37 Sec. 4.1.4, Manufacturer B's listed units may sit 18 in from a combustible wall at the rear and 3 ft at the front and ends; this does not apply to unprotected openings.
- Manufacturer B requires overhangs and other overhead structures to be at least 5 ft above the top of the generator and removable fence panels at least 3 ft away.
- Manufacturer A's manual says furnace and similar air intakes must be at least 10 ft (3 m) from the generator's exhaust end.
- Manufacturer A asks for plants and other combustibles to be cleared at least 4 ft (1.2 m) beyond the exhaust end and says the generator must be installed outdoors.
- Manufacturer C says a home standby unit needs at least 5 ft from doors, windows and other openings and should be no less than 18 in from the home, subject to local code.
- Unincorporated Miami-Dade County requires generator exhaust to be 10 ft from wall openings and sets residential setbacks of 5 ft rear and 3 ft (RU districts) or 5 ft (EU, AU, GU) interior side, and never closer than 10 ft to a side street line.
- CDC's 20-foot advice is for portable generators; it is not the standby clearance rule.
The four rulebooks that decide where your generator goes
Most articles give one number, usually 5 feet, and stop. In practice, four different sets of rules apply at the same time, and the strictest one wins.
| Rulebook | Who writes it | What it controls | Where to find it |
|---|---|---|---|
| NFPA 37 | National Fire Protection Association | Fire separation of stationary engines from buildings and combustibles | Adopted by reference through the fire, building and fuel gas codes your city uses |
| Manufacturer's installation manual | The generator maker | Clearances for airflow, service, exhaust, overhead structures and fences; pad requirements | Installation manual and spec sheet for your exact model |
| Local building, mechanical and zoning code | City or county | Exhaust distance from openings, property-line setbacks, flood elevation, permits | City permit office and zoning code |
| HOA or deed restrictions | Your association | Location, screening, appearance (limited by state law in Texas and Florida) | Your declaration and architectural guidelines |
A spot can pass NFPA 37 and still fail the manual, or pass both and break a side-yard setback. Your installer's site survey should check all four.
What does NFPA 37 say about distance from a house?
NFPA 37 is the National Fire Protection Association's Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines. The full text is sold by NFPA and is not free online, so this guide relies on how manufacturers summarize it in their installation documents. Check the edition your city has adopted with the permit office.
According to one major manufacturer's 2026 site-selection instructions, NFPA 37 limits the spacing of an engine generator to a minimum of 5 feet (1.5 m) from an opening in a structure or from a structure having combustible walls, and requires the generator to be readily accessible for maintenance, repair and first responders.
The tested-enclosure exception (Section 4.1.4)
The same document explains that NFPA 37 contains an exception allowing an engine generator closer to a combustible wall when approved testing shows that a fire starting at the engine will not ignite the structure. The manufacturer had its units tested by Southwest Research Institute (SwRI), a third-party testing and listing agency. Based on that testing and NFPA 37 Sec. 4.1.4, it permits:
- 18 inches (457 mm) from the back of the generator to a combustible wall; and
- 3 feet (0.91 m) from the front and ends.
Two limits are easy to miss:
- The reduction applies only to tested, labeled units. Look for the SwRI marking on the enclosure and in the manual.
- It does not apply to clearances from unprotected openings, or from protected openings with less than a 1-hour fire rating. A window, door or vent still needs the full distance your local code requires.
So the common phrase "18 inches from the house" really means 18 inches from a solid wall section with no window, door or vent within the locally required distance.
How far must a generator be from windows, doors and vents?
The answer depends on your local code and your manual, and the manuals defer to local code on purpose. Here is what the documents say:
| Source | Distance from windows, doors, openings |
|---|---|
| NFPA 37 (as summarized by manufacturers) | 5 ft from openings, unless reduced under the tested exception (which does not apply to unprotected openings) |
| Manufacturer B site selection (2026) | No windows, doors, vents, window wells or wall openings closer than locally adopted codes allow |
| Manufacturer C help article | At least 5 ft from doors, windows and other openings |
| Manufacturer A installation manual | Distance from a structure depends on state and local codes; see the model's dimension drawing |
| Unincorporated Miami-Dade County | Exhaust 10 ft from wall openings, per the Florida Residential Code (Florida Mechanical Code for commercial) |
Treat 5 feet from any operable opening as the floor and expect some jurisdictions to require more for the exhaust side. Miami-Dade's 10-foot exhaust rule is a good example of a local code going further than the national summary.
Openings people forget
The manufacturer's carbon monoxide entry-point list includes more than windows and doors: garage doors that do not seal, attic, ridge and soffit vents, basement windows and crawl-space hatches, furnace intake and exhaust pipes, dryer vents, and cracks in brick, mortar or foundation. It also warns that corners, alcoves, fences, courtyards and heavy vegetation can trap exhaust. A unit placed to meet NFPA distances "may still allow CO within the structure," and the manufacturer says it may need to go farther away than NFPA requires.
How far from a bedroom window should the exhaust be?
No national rule names bedroom windows separately. But the bedroom window matters most, because the weekly test may run while someone is asleep and an outage often lasts through the night. Practical steps:
- Check which end of your model blows exhaust. Many air-cooled units discharge hot air and exhaust from one end. Point that end away from the house and away from any window.
- Keep the exhaust end at least the locally required distance from the bedroom window. If your city has no specific rule, Miami-Dade's 10 feet is a sensible benchmark.
- Consider prevailing winds. The manufacturer instructions suggest a windbreak at a safe distance if wind will blow exhaust toward openings.
- Install CO alarms. The manufacturer recommends CO detectors on each level of the structure next to the generator, referencing NFPA 72 and IRC Section R315, and notes that smoke alarms do not detect CO.
For more on CO alarms and symptoms, see our generator carbon monoxide safety guide.
Why the 20-foot rule is for portable generators, not standby units
The CDC advises running a generator outdoors more than 20 feet from windows, doors and vents. That advice is written for portable generators, which have open engines and exhaust that often points wherever the unit happens to be set down. Miami-Dade's generator page also tells owners to keep portable generators 10 feet from windows, doors and other openings while in use, and to store them indoors empty of fuel.
Home standby generators are a different product. They sit in a factory enclosure on a fixed pad, with a known exhaust direction, and their placement is set by NFPA 37, the manual and the local code. Do not mix the two numbers. A standby unit 6 feet from a solid wall can be fully code-compliant, while a portable generator at 6 feet from a window is dangerous.
After Hurricane Irma in 2017, a study by the Florida Department of Health found that of 340 people who ran a generator outside, 63.5% had it within 20 feet of windows, doors, air conditioners or air intake vents. That is a portable-generator problem, and the reason the 20-foot advice exists. See our portable generator safety guide.
Can a generator go under a deck, overhang or soffit?
Usually not directly underneath. One manufacturer's instructions require structures, overhangs or projections from a wall above the generator, or above its front, end and rear clearance zones, to be at least 5 feet (1.52 m) vertically above the top of the generator. A typical roof eave, second-story deck or carport roof is often lower than that once you add the generator's height.
Manufacturer A's manual adds that a generator should not be located near patios, decks, play areas or animal shelters. Soffit vents are also on the CO entry-point list. If the only open wall is under a low eave, the installer may need to move the unit outward into the yard so the overhang is not above the unit or its clearance zone.
How far from my AC unit, gas meter and electric meter?
Air conditioner condenser
The manufacturer site instructions say not to direct generator discharge into HVAC components, including make-up air systems, AC condensers (which may blow exhaust into openings) and window AC units. They also point to Section 401 of the ICC Mechanical Code for outdoor air intake locations. Manufacturer A requires furnace and similar air intakes to be at least 10 feet from the exhaust end. In Texas and Florida, where the condenser is often on the same side yard as the meters, the usual fix is to orient the exhaust end away from the condenser and keep the generator's 3-foot service zone clear of it.
Gas meter
Generator manuals do not give a single national distance from the gas meter. The site instructions tell installers to contact local utility providers and verify the location meets all utility placement requirements, noting that this could affect warranty coverage, and that laws or codes may regulate distance to specific utilities. Your gas utility's meter-set rules and the fuel gas code adopted by your city control here. If your gas service needs a larger meter, see our gas meter upgrade guide.
Electric meter and transfer switch
Placing the generator near the meter and the transfer switch keeps wire runs short. One manufacturer notes that longer conduit and fuel line runs raise installation cost because of trenching, so units are usually placed close to the fuel and electric meters. Short runs also help in Texas HOAs, where a location rule that raises line costs by more than 20% is unenforceable under Property Code 202.019(e).
Propane tank
A separate propane tank has its own distance rules from buildings, property lines and ignition sources under NFPA 58, adopted in Texas by the Railroad Commission (2017 edition) and in Florida by FDACS rule 5J-20.002 (2024 edition, effective November 17, 2026). See our propane tank installation rules.
What clearance do service technicians need?
Service room is built into the manufacturer clearances. One maker's instructions say the 3-foot front and end clearances and 18-inch rear clearance are "primarily for fire prevention, but also to provide sufficient room for removing front and end panels for maintenance." They also call for maneuvering space for routine tasks like battery replacement and engine service, and reference NEC 110.26 (in earlier editions), the National Electrical Code's working space rule for electrical equipment; section numbers may have been renumbered in the edition your jurisdiction enforces.
Manufacturer A's units put the battery, fuel system and electrical connections in the air intake area, reached by raising the roof and removing an enclosure panel. If the lid cannot open fully because of a soffit or a window ledge, routine service becomes hard and may not meet the manual.
Does a generator need a concrete pad?
Not always. One manufacturer says its units are typically approved for pea gravel, crushed stone or a concrete base pad, and that the base must be non-combustible. Key details from its 2026 instructions:
- The surface must be compacted, level and not erode over time. The generator must be level within 0.5 inch all around.
- For gravel or crushed stone, prepare an area about 5 inches thick and about 3 inches longer and wider than the generator on all sides.
- The maker lists recommended concrete pads 3 inches and 4 inches thick.
- Any base pad must meet local codes, including wind ratings.
Manufacturer A ships some models with a composite mounting pad and says to set it on compacted gravel with a weed barrier, or on concrete, and never directly on grass, wood or other combustible material.
When local code requires more
In unincorporated Miami-Dade County, the generator permit review covers the pad: soil bearing capacity, pad size and thickness, and anchoring details under the Florida Building Code, using the county's generator structure form. Coastal and high-wind areas often need an anchored concrete pad. See our flood zone and wind anchoring guide.
Can I put a generator on a roof or raised platform?
Yes, if the design meets NFPA 37 Section 4.1.3, according to one manufacturer's installation instructions. The surface beneath the generator, and beyond it, must be noncombustible for at least 12 inches (30.5 cm). The manufacturer tells installers to ask the local building inspection or fire department which noncombustible materials are approved.
Platforms are common in flood zones. In Miami-Dade, equipment must be above the Base Flood Elevation or the required lowest floor elevation. A platform also needs engineering for the generator's weight (a 22 kW air-cooled unit in one maker's line weighs about 451 pounds), wind loads and service access. Expect the permit office to want sealed structural drawings for a raised stand.
Can a standby generator go in a garage or shed?
Not a residential air-cooled unit. Manufacturer A's manual states the generator set must be installed outdoors, and both major manuals warn never to run a generator where exhaust can be drawn into an occupied building. Garages and sheds trap exhaust, and the CPSC warns that CO can build up and linger for hours even with doors open. Some large commercial generators are designed for indoor generator rooms with engineered ventilation and exhaust piping, but that is a separate design under commercial codes, not a homeowner option.
Can the generator go in a side yard near the property line?
Often yes, but zoning setbacks can block it. Setbacks are minimum distances between equipment and property lines, set by the city or county zoning code, and they vary widely.
Example: unincorporated Miami-Dade County
The county's generator permit page sets these residential setbacks for propane or natural gas generators up to 5 feet tall:
| Location | Minimum setback |
|---|---|
| Rear property line | 5 ft |
| Interior side line, RU zoning districts | 3 ft |
| Interior side line, EU, AU and GU districts | 5 ft |
| Side street property line | Never closer than 10 ft |
The same page says diesel and other liquid-fueled generators and their fuel supply (gas-fueled systems excluded) must be at least 100 feet from any potable water supply well, and that generators in easements need Public Works review. Cities inside Miami-Dade, such as Miami and Miami Beach, run their own building departments, so check with the municipality if you live inside one.
Texas cities
Houston, Dallas, San Antonio, Austin and Fort Worth each have their own development codes and permit offices. Our review of their current public permit pages did not find a generator-specific setback table to quote, so confirm property-line distances with the permit office or through your installer before buying. In many Texas subdivisions, recorded deed restrictions also set side-yard rules. Texas Property Code 202.019 lets an HOA regulate location, but not if the rule raises installation cost by more than 10% or line cost by more than 20%. See the Texas permit guide.
Zero-lot-line homes and townhomes
On zero-lot-line and townhome lots in Houston, Dallas-Fort Worth, Orlando and Tampa suburbs, one side wall often sits on the property line and the other side yard may be 5 to 10 feet wide. After subtracting the 18-inch rear clearance, a roughly 2-foot-deep unit, and the 3-foot service zone in front, there may be no legal side-yard spot. Rear-yard placement or a smaller unit with a different exhaust direction may be the only option. Ask for the installer's site sketch with all distances written on it.
Can shrubs or a fence screen my generator?
Yes, if they stay out of the clearance zones. From the manufacturer documents:
- Shrubs, bushes and trees count toward the 3-foot front and end clearance and the 18-inch rear clearance.
- Removable fence panels without footings, used as a visual surround, cannot be within 3 feet of the unit.
- Manufacturer A asks for combustibles, including plants, to be cleared at least 4 feet beyond the exhaust end and says hot exhaust should not blow on plants.
- Do not try to conceal the generator with plants. Exhaust can also stunt plant growth.
- Keep the air inlet and outlet clear of leaves and grass clippings.
Also keep sprinklers, gutter downspouts and sump pump discharge from spraying or flooding the unit. The manufacturer notes that excess moisture speeds corrosion and shortens life. In Texas, an HOA can require screening only where the unit is visible from the street or through an open fence (Property Code 202.019(c)(9)).
Florida placement notes: coastal lots, flood zones and condos
- Flood elevation. In unincorporated Miami-Dade, the residential required elevation is the Base Flood Elevation or the crown of road or County Flood Criteria plus 8 inches, whichever is higher.
- High ground. The manufacturer instructions say to pick high ground where water will not rise and flood the generator, which should not operate in or sit in standing water.
- Wind. Base pads must meet local wind requirements. Miami-Dade and Broward are in the Florida Building Code's High-Velocity Hurricane Zone.
- Townhomes and condos. Ground around condo buildings is usually a common element controlled by the association. Florida HOAs must adopt hurricane protection specifications that include exterior fixed generators under Statute 720.3035(6). See our Florida HOA and condo guide.
City pages: Miami, Tampa, Orlando, Jacksonville.
Quick placement worksheet
Use this table with your installer at the site survey. Fill in the actual distances.
| Check | Typical requirement | Your site |
|---|---|---|
| Rear of unit to solid combustible wall | 18 in (tested units only) or 5 ft | |
| Front and ends to anything (walls, shrubs, AC unit) | 3 ft | |
| Any point of unit to nearest window, door or vent | Local code; 5 ft minimum; 10 ft for exhaust in Miami-Dade | |
| Exhaust end to furnace or fresh-air intake | 10 ft (Manufacturer A) | |
| Top of unit to overhang above | 5 ft | |
| Removable fence panels | 3 ft | |
| Combustibles beyond exhaust end | 4 ft (Manufacturer A) | |
| Property line setbacks | Local zoning | |
| Flood elevation | At or above BFE or local standard | |
| Pad level | Within 0.5 in |
Distances in this table come from the cited manufacturer documents and Miami-Dade County. Your model's manual and your city's code control.
How to choose a provider
- Get the installation manual for the exact model you are buying and find the clearance diagram.
- Check for the SwRI label if you plan to use the 18-inch rear clearance.
- Mark every window, door, vent, dryer vent and soffit vent within 10 feet of the planned spot.
- Point the exhaust end away from the house, bedroom windows, AC condenser and fresh-air intakes.
- Measure overhead clearance; overhangs must be at least 5 feet above the unit.
- Confirm property-line setbacks and easements with the city or county.
- Ask the gas and electric utilities about meter clearance rules.
- Check the flood zone and required elevation for the lot.
- Plan the pad: gravel or concrete, level within 0.5 inch, anchored where wind code requires.
- Plan screening at least 3 feet away and keep sprinklers and downspouts off the unit.
- Install CO alarms on every level of the home.
Related standby generator installation guides
- Generators in Flood Zones and Hurricane Winds: Elevation, Anchoring and Storm Prep
- Can My Texas HOA Stop Me From Installing a Generator? Property Code 202.019 Explained
- Generator Permits in Texas: Houston, Dallas, San Antonio, Austin and Fort Worth
- Generator Permits in Florida: Miami-Dade, Broward, Palm Beach, Tampa, Orlando and Jacksonville
- How Many People Die From Generator Carbon Monoxide, and How Do You Stay Safe?
- Propane Tank Installation Rules for Generators: Setbacks, Underground Tanks and Anchoring
- How Loud Is a Generator? Decibel Ratings, Noise Ordinances and Quiet-Test Settings
- Standby Generator Installation: Step-by-Step Process and How Long It Takes
Standby generator installation by state and city
Questions people ask
How close to my house can a standby generator be installed?
For units tested under the NFPA 37 Section 4.1.4 exception, one major manufacturer allows 18 inches from a combustible wall at the rear of the generator and 3 feet at the front and ends. Untested units fall back to the 5-foot NFPA 37 distance. In every case, windows, doors and vents need the full distance your local code requires, and your manual may add more.
Is the 5-foot rule the law?
The 5-foot figure comes from NFPA 37, a national standard. It becomes enforceable when your state or city adopts a code that references it, which is common. Generator makers also require compliance with NFPA 37, NFPA 54, NFPA 58, NFPA 70 and the ICC fuel gas code in their manuals. Local code can be stricter, as Miami-Dade's 10-foot exhaust-to-opening rule shows.
Can a generator go next to my air conditioner?
It can sit in the same side yard, but do not direct generator discharge into the AC condenser, which can push exhaust toward openings. Keep the 3-foot front and end clearances free of the condenser. Manufacturer A requires furnace and similar air intakes to be at least 10 feet from the exhaust end.
Do I need a permit to place a generator in my yard?
In most Texas and Florida cities, yes, at least an electrical permit, and usually a gas permit. Unincorporated Miami-Dade requires a building permit with signed and sealed plans and a site plan showing distances to buildings and property lines. Texas cities' authority over residential backup systems changed in 2025 under SB 1252, so ask your city what it now requires.
Can I put my generator on a wood deck?
Not directly on combustible material. Manufacturer instructions require any roof, platform or deck placement to follow NFPA 37 Section 4.1.3, with a noncombustible surface under and at least 12 inches beyond the unit. Manufacturer A also advises against locating the generator near decks and patios. An engineer usually designs raised platforms.
Can a generator be closer than 5 feet if there are no windows on that wall?
Yes, for tested units. The SwRI-tested reduction lets the rear sit 18 inches from a combustible wall, provided there is no unprotected opening, or opening with less than a 1-hour fire rating, within the locally required distance. Check the wall above, too: soffit vents and windows on the second story count.
Does an HOA have to accept the code-approved location?
In Texas, an HOA may regulate location, but the rule is unenforceable if it raises installation cost by more than 10 percent or electrical and fuel line cost by more than 20 percent (Property Code 202.019(e)). In Florida, an HOA must approve an application that conforms to its adopted hurricane protection specifications (720.3035(6)).
How much clearance does a generator need above it?
One manufacturer requires at least 5 feet of vertical distance between the top of the generator and any structure, overhang or projection above the unit or above its clearance zones. This is for heat, airflow and service access, and to keep fire away from the eaves.
Can I move my generator later?
Yes, but it is a new installation in the eyes of the permit office. Moving the unit means new wiring, new gas piping, a new pad and usually a new permit and inspection. It is far cheaper to get the location right during the first site survey.
Sources
- Manufacturer B Site Selection instruction sheet, Part A0005151099 Rev. B (06/12/2026)
- Manufacturer B 22-28 kW air-cooled standby spec sheet (Rev. D, 08/13/2026)
- Manufacturer B 22 kW standby generator product page (dimensions, weight)
- Manufacturer A TP-6803 installation manual
- Manufacturer C: Optimal placement of a home standby generator
- Miami-Dade County: Generators permit requirements
- CDC: About carbon monoxide poisoning
- CPSC Portable Generator Safety Alert
- Florida DOH study of Hurricane Irma CO exposures (PMC)
- Texas Property Code ch. 202 (202.019)
- Florida Statute 720.3035
- Railroad Commission of Texas LP-gas rules (NFPA 58-2017 adoption)
- Florida rule 5J-20.002 (NFPA 58/54 2024, NFPA 110 2025)
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


