Local Guide · Standby generator installation
Do I Need a Bigger Gas Meter for a Generator? Working With Your Gas Utility
How to tell whether your gas meter can feed a standby generator, how pipe is sized, who may run the line in Texas and Florida, and how to keep the utility step from delaying your project.
You need a bigger gas meter when the generator's maximum fuel input plus all your other gas appliances exceeds what the meter and regulator can deliver. Add every appliance's Btu/hr rating to the generator's (a 20 kW unit can draw about 281,000 Btu/hr, roughly 281 cubic feet per hour) and have your installer send that total to the gas utility. Only the utility can change the meter, and its schedule often sets the project timeline.
Key facts
- Manufacturer A says the utility gas meter must supply the generator at rated load plus all other gas appliances, and to contact the supplier for a meter upgrade if needed.
- Manufacturer A 20 kW residential models draw up to 281,000 Btu/hr on natural gas; 14 kW models up to 193,000 Btu/hr.
- Manufacturer A specifies 5 to 11 in. w.c. natural gas supply pressure for most residential models and 7 to 11 in. w.c. for LP.
- Manufacturer A's pipe table calls for 1 in. pipe up to 50 ft and 1-1/4 in. at 100 to 200 ft for a 20 kW unit on natural gas, adding 8 ft per 90 degree elbow.
- Texas Occupations Code 1301.002 makes gas piping plumbing work licensed by the Texas State Board of Plumbing Examiners.
- Florida 489.105 includes natural gas and LP gas lines in a plumbing contractor's scope; 527.01(10) lets Category V LP installers work on natural gas piping too.
- Florida City Gas says customers are responsible for gas lines from the meter to their equipment.
- Texas RRC emergency rules give residences and other human needs customers the highest priority for natural gas deliveries (FERC-NERC Uri report).
Why the gas meter can stall a generator project
A home standby generator on natural gas is often the largest gas appliance on the property. A 20 kW air-cooled unit can draw as much gas as a furnace, a water heater, a range and a dryer combined. Your existing gas meter and service line were sized years ago for the appliances you had then. If the generator pushes total demand past what the meter and regulator can deliver, the generator will not reach its rated output, or it will stall when a big load like the air conditioner kicks on.
Manufacturers are direct about this. Manufacturer A's residential installation manual tells the installer to verify that the output pressure from the primary gas utility regulator is within the generator's range, and that the utility gas meter flow rate is sufficient to supply the generator set at rated load plus all other gas-consuming appliances. It says to contact the fuel supplier for flow rate information or a gas meter upgrade if necessary.
The meter belongs to the utility, not to you. Only the utility can change it, and its schedule does not depend on your installer's. That is why the meter step is one of the most common reasons a generator sits on its pad for weeks waiting to be fueled. Florida City Gas, for example, says it monitors the pipelines up to your meter, while the customer is responsible for maintaining the lines that begin at the meter and run to gas equipment in the home and yard. So the utility handles the meter and service line; your licensed contractor handles everything after it.
How do I know if my gas meter can handle a generator?
You need two numbers: what the meter can deliver and what everything connected to it can use at the same time.
Step 1: add up connected load in Btu per hour
Every gas appliance has a rating plate listing its input in British thermal units per hour (Btu/hr). Write each one down. Then add the generator's maximum fuel input from its spec sheet or manual.
Manufacturer A lists these maximum natural gas inputs in its residential manual:
| Generator | Natural gas, max input | LP, max input |
|---|---|---|
| Manufacturer A 14 kW residential | 193,000 Btu/hr | 203,000 Btu/hr |
| Manufacturer A 20 kW residential | 281,000 Btu/hr | 340,000 Btu/hr |
Larger generators, such as 22 kW to 26 kW air-cooled units or liquid-cooled models, use more. Use the manual for your exact model.
Step 2: convert to cubic feet per hour
Meters are rated in cubic feet per hour (cfh). Manufacturer A uses a nominal 1,000 Btu per cubic foot for natural gas, so 281,000 Btu/hr is about 281 cfh. Local gas heat content varies a little; the utility knows the exact figure.
Example (illustrative numbers)
Suppose your rating plates read: furnace 80,000 Btu/hr, tank water heater 40,000, range and oven 65,000, dryer 22,000. That is 207,000 Btu/hr, about 207 cfh. Add a 20 kW generator at 281 cfh and the total connected load is about 488 cfh. If your meter is rated well below that, the utility will likely need to upsize the meter, the regulator or both.
Step 3: read the meter or ask the utility
Many residential meters carry a capacity marking on the face or nameplate, but the reliable answer comes from the utility, which knows the meter model, the regulator and the pressure on your service line. Your installer submits a load letter or service request listing the new total load. The utility decides whether the meter, regulator or service line must change.
Why "connected" load, not average use
During an outage, everything can run at once: the generator at full load while the furnace or water heater fires. Utilities and the fuel gas codes size for that worst case, not your average bill.
What is elevated pressure gas service and do I need it?
Most homes get gas at a low delivery pressure measured in inches of water column (in. w.c.). Manufacturer A specifies a natural gas supply pressure of 5 to 11 in. w.c. for most of its residential models (3.5 to 11 for one 20 kW model) and 7 to 11 in. w.c. for LP. If pressure at the generator inlet falls below the minimum when the engine is under load, the generator cannot make full power.
When a long pipe run or a big generator makes low-pressure piping impractically large, some utilities offer elevated pressure service. The utility delivers gas at a higher pressure (commonly measured in pounds per square inch rather than inches of water). Smaller pipe can then carry the same energy, and a regulator near the generator or the appliances steps the pressure down to what each appliance needs.
- Pros: smaller, cheaper pipe on long runs; less pressure drop when the generator starts.
- Cons: not every utility offers it for homes; it needs extra regulators that must be vented and maintained; the utility may charge for the change and require its own approval.
We could not confirm published elevated-pressure policies or fees for the Texas and Florida gas utilities named below. Ask your utility directly whether it offers elevated pressure residential service, what pressure it delivers, and what it charges.
What size gas pipe runs to a 22 kW generator?
Pipe size depends on three things: the generator's gas demand in cfh, the length of pipe from the meter regulator to the generator, and the allowed pressure drop. The International Fuel Gas Code (IFGC) and NFPA 54, the National Fuel Gas Code, provide sizing tables that list how many cubic feet per hour each pipe size carries over each length at a set pressure drop. The installer reads the table at the total length, including fittings, and picks a pipe that carries the load.
Manufacturer example
Manufacturer A's manual gives this minimum natural gas pipe size table for its residential units, measured from the primary gas pressure regulator to the generator inlet, adding 8 feet of equivalent length for each 90 degree elbow:
| Pipe length | 14 kW, natural gas (193,000 Btu/hr) | 20 kW, natural gas (281,000 Btu/hr) | 20 kW, LP (340,000 Btu/hr) |
|---|---|---|---|
| 25 ft | 3/4 in. | 1 in. | 3/4 in. |
| 50 ft | 1 in. | 1 in. | 1 in. |
| 100 ft | 1 in. | 1-1/4 in. | 1 in. |
| 150 ft | 1-1/4 in. | 1-1/4 in. | 1-1/4 in. |
| 200 ft | 1-1/4 in. | 1-1/4 in. | 1-1/4 in. |
A 22 kW unit from another maker draws somewhat more gas than a 20 kW, so the answer is often 1 inch on short runs and 1-1/4 inch or more on long ones. That is a planning range only. The installer must size from your model's manual and the fuel gas code your city adopted.
Elbows count
Manufacturer A's rule of adding 8 feet per 90 degree elbow means a 40-foot run with four elbows sizes like a 72-foot run. Running the line straight along the wall instead of around a patio can drop a pipe size.
Flexible connector at the unit
Manufacturer A says to have rigid gas piping and a manual shutoff valve installed, ending about 12 inches from the generator inlet, with a short flexible section to prevent breakage from vibration, and not to bend the flexible line to make up for misalignment.
Can the generator share a line with my water heater and furnace?
It can share the meter, and sometimes part of the house piping, but only if every section of pipe is sized for the combined load it carries. In practice many installers run a dedicated line from the meter outlet to the generator. That keeps the generator from starving the furnace or water heater, and keeps a long-buried house line from limiting the generator.
Signs a shared line is too small:
- The generator runs fine on a test but surges, hunts or drops voltage when the AC compressor starts.
- Gas appliances flicker or a pilot goes out when the generator starts.
- The generator throws an underspeed or low-frequency fault under load.
If those happen, the fixes are, in order of cost: shorten or straighten the run, upsize the pipe, add a dedicated line from the meter, ask the utility for a bigger meter or regulator, or ask about elevated pressure service.
What happens if gas pressure drops when the generator starts?
Engines need a steady flow of fuel. When a large electrical load hits the generator, the engine opens its throttle and gas demand jumps. If the supply cannot keep up, the inlet pressure falls below the minimum. The result can be:
- Engine speed sags, so output frequency drops below 60 Hz. Generator controllers watch for this. Manufacturer A's controller, for example, uses frequency droop to shed lower-priority loads when a load management system is installed.
- Voltage dips that can make lights flicker and motors struggle.
- Shutdown on an underspeed or overcrank fault, leaving the house dark.
A good installer measures inlet pressure at the generator with a manometer (a gauge that reads inches of water column) while the generator runs at full load, not only at idle. Ask for that reading on the commissioning sheet.
What about grid-wide gas problems?
Because gas distribution pipes run underground, the winds that topple power lines during a hurricane usually do not reach them, although flooding and uprooted trees can damage meters and service lines. Winter Storm Uri in February 2021 was different. The FERC-NERC staff report found that massive natural gas production declines left the fuel supply struggling to meet both residential heating and power plant demand. The same report notes that Texas Railroad Commission rules give the highest priority in emergencies to deliveries to residences, hospitals, schools and other human needs customers, and the RRC's emergency order during the event kept residences first. Home gas service stayed on for most customers, but it shows why some Texas owners consider propane or a dual-fuel setup as a backup. See natural gas vs propane.
The gas utility process in Texas and Florida
Each gas utility runs its own process and fees, and we could not confirm a published generator-specific procedure or fee schedule for any of the major utilities below. The general sequence is similar everywhere:
- Load calculation. Your installer adds up existing appliances plus the generator.
- Request to the utility. The installer or homeowner submits a service change or load addition request listing the total Btu/hr or cfh, the address and the account number.
- Utility review. The utility decides whether the meter, regulator or service line must change and whether any charge applies.
- Scheduling. The utility sets a date to swap the meter or regulator. Gas is shut off briefly, and appliances must be relit afterward.
- House-side work and inspection. The licensed contractor runs and pressure tests the new piping, and the city inspects it.
- Gas-in and start-up. The generator is connected, leak checked and commissioned.
Major natural gas utilities to contact
| State | Utility | Where to start |
|---|---|---|
| Texas | CenterPoint Energy (Houston area gas) | Residential or builder services contact; ask about load additions |
| Texas | Atmos Energy (Dallas-Fort Worth and much of North Texas) | Customer service; ask for a meter or load change |
| Texas | Texas Gas Service (Austin area and others) | Customer service; ask about generator load |
| Texas | CPS Energy (San Antonio gas and electric) | Gas service standards and service applications |
| Florida | TECO Peoples Gas | New service or load change request |
| Florida | Florida City Gas | Builders and developers line (888-CITYGAS for sales) or customer service 800-993-7546 |
| Florida | Florida Public Utilities (FPU) | Builder and developer services; emergencies 800-427-7712 |
Questions to ask the utility:
- What is the rated capacity of my current meter and regulator?
- Is there a charge for upsizing, and is it billed to me or my contractor?
- How long is the current wait for a meter change?
- Do you offer elevated pressure residential service?
- Do you need a city inspection approval before you set a larger meter?
Lead times
Meter changes are not emergency work, so they get scheduled around the utility's other jobs. After a big storm, crews shift to restoration and repairs, and routine changes wait. Homeyou's 2026 cost guide notes that utility or gas-provider coordination can extend generator timelines beyond the on-site work days. Ask your installer to file the utility request as soon as you sign the contract, not after the generator is set. For the full schedule, see installation process and timeline.
Who is allowed to run gas piping to a generator?
Texas
- Natural gas: Occupations Code 1301.002 defines plumbing to include piping used to supply or distribute gas and piping outside a building that connects it to a gas supply on the premises. Natural gas piping to a generator is plumbing work licensed by the Texas State Board of Plumbing Examiners (TSBPE). TSBPE issues Responsible Master Plumber, Master, Journeyman and Tradesman Plumber-Limited licenses. Check the license on the TSBPE site.
- Propane: LP-gas piping is regulated by the Railroad Commission of Texas under Natural Resources Code chapter 113. Licensed plumbers and certain AC contractors can register for an RRC exemption from the Category D license ($50 fee), but only the registered individual may then do the LP work.
- Electrical: the generator and transfer switch wiring are electrical work for a TDLR-licensed electrical contractor under Occupations Code chapter 1305.
Florida
- Natural gas: Florida 489.105 includes installing natural gas and LP gas lines in a plumbing contractor's scope, licensed through DBPR's Construction Industry Licensing Board.
- Also allowed: Florida 527.01(10) defines a Category V LP Gas Installer to include design, installation, servicing and modifying piping, tubing, tanks and equipment for liquefied petroleum or natural gas. So an FDACS Category V licensee may also do natural gas piping work.
- Which license the permit office wants can differ by county. Ask the building department in Miami-Dade, Hillsborough, Orange or Duval which license may pull the gas permit.
More detail: Texas installer licensing and Florida installer licensing.
Does the city inspect generator gas piping?
In most of Texas and Florida, yes. The gas line is plumbing or fuel gas work under the locally adopted code, and it typically needs a permit and inspection separate from the electrical permit.
- Pressure test. The inspector usually wants to see the new piping holding a test pressure on a gauge before trenches are backfilled.
- Leak check at gas-in. Manufacturer A's manual says to test all fuel connections with soapy water after opening the valves and to check again with the generator running. Its maintenance section specifies a soap solution leak test at 6 to 8 ounces per square inch (10 to 14 in. w.c.) and warns against soaps with ammonia or chlorine.
- Final. Shutoff valve, sediment trap where required, flexible connector, pipe support and burial depth.
Texas 2025 law changes
Texas S.B. 1252 (2025) bars cities from regulating installation or inspection of residential energy backup systems of 50 kW or less, but TDLR says licensed electrical work and the NEC still apply, and municipally owned utilities keep their authority. S.B. 1202 (2025) added Local Government Code 247.0025, allowing a qualified third party to review and inspect a home backup power installation, with the city required to issue approval within three business days of notice. How each city applies these laws to the gas line, which is plumbing, varies. Ask the permit office. See Texas permits and Florida permits.
What it costs to run a generator on natural gas
Fuel use scales with load. Manufacturer A's data for its 20 kW residential unit lists natural gas use at 281 cfh at full load, 243 at 75 percent, 161 at 50 percent and 127 at 25 percent. For the 14 kW unit: 193, 163, 124 and 93 cfh.
Inch Calculator's 2023 cost guide estimated that running a natural gas standby generator costs about $25 to $50 for a full day depending on gas prices, and weekly self-exercise about $5 to $10 a month. Your actual cost is the cfh used times your utility's rate per hundred cubic feet or per therm, plus any fixed charges. For runtime and oil-change planning on long outages, see generator runtime and fuel consumption.
How to choose a provider
- List every gas appliance's Btu/hr from its rating plate.
- Get the generator's maximum natural gas input from the manual for your exact model.
- Have the installer submit the load addition request to the gas utility right after signing.
- Ask the utility about meter capacity, upgrade charges and the current wait.
- Measure the planned pipe route and count elbows; size pipe from the manual and the local fuel gas code.
- Decide on a dedicated line from the meter versus sharing house piping.
- Confirm the gas contractor's license: TSBPE in Texas, CILB plumbing or FDACS Category V in Florida.
- Make sure a gas permit is pulled and the pressure test is inspected before backfill.
- At start-up, ask for inlet gas pressure measured at full load on the commissioning sheet.
- Keep the meter change confirmation, permit, test record and commissioning sheet together.
Related standby generator installation guides
- Natural Gas vs Propane Generators: Cost, Runtime, Reliability and Which Is Right for You
- Standby Generator Installation: Step-by-Step Process and How Long It Takes
- What Size Generator Do I Need? A Load Calculation Walkthrough for Your Home
- Who Can Legally Install a Standby Generator in Texas?
- Who Can Legally Install a Standby Generator in Florida?
- Generator Permits in Texas: Houston, Dallas, San Antonio, Austin and Fort Worth
- Generator Permits in Florida: Miami-Dade, Broward, Palm Beach, Tampa, Orlando and Jacksonville
- How Long Can a Standby Generator Run? Continuous Runtime, Fuel Use and Oil Changes
Standby generator installation by state and city
Questions people ask
Do I need a gas meter upgrade for a standby generator?
Often, yes, especially for 20 kW and larger units in homes that already have a gas furnace, water heater and range. The test is simple: add the Btu/hr ratings of every gas appliance plus the generator's maximum input and compare with what the meter and regulator can deliver. Manufacturer A's manual, for example, lists 281,000 Btu/hr for its 20 kW unit on natural gas. If the total exceeds the meter's capacity, the utility must upsize it before the generator can run at full output.
How long does a gas meter upgrade take?
The swap itself is usually quick, but the wait for a utility appointment can run from days to several weeks, and longer after storms when crews shift to repairs. Few utilities publish a firm timeline, so ask when you submit the request. File the load request as soon as you sign the generator contract so the meter work runs in parallel with permits and equipment delivery.
Does the gas utility charge for a meter upgrade?
It depends on the utility and its tariff. Some include residential meter upsizing at no charge; others bill for meter, regulator or service line changes, especially when the service line itself must be replaced. We could not confirm current published fees for the major Texas and Florida gas utilities, so ask for the charge in writing before work starts and check whether your installer's quote includes it.
Can a portable generator run off my home's natural gas line?
Only if the portable is built or converted for natural gas and the connection is made by a licensed gas contractor with a permit, using a proper shutoff valve and listed connector. Never improvise a hookup to a gas appliance line. The portable still must sit outdoors far from windows and doors because of carbon monoxide. See our dual-fuel and tri-fuel guide for details.
Will a bigger meter raise my gas bill?
A bigger meter does not by itself make you use more gas. Your bill depends on how much gas flows through it. Some utilities have different fixed monthly charges by meter class, so ask whether a larger meter changes your customer charge. The generator's weekly exercise uses a small amount; Inch Calculator's 2023 guide put self-exercise at roughly $5 to $10 a month.
Is natural gas or propane more reliable during a hurricane?
Underground natural gas lines usually keep flowing through hurricanes, so you never need a delivery. Propane is stored on site, so it does not depend on the pipeline but does depend on tank size and delivery trucks. Flooding can damage either system's above-ground parts. In Texas, Winter Storm Uri showed natural gas supply can be strained in extreme cold, though RRC rules put residences first. Many owners on gas still keep a backup plan for the rare long event.
What pressure does a generator need?
Check the manual. Manufacturer A specifies 5 to 11 inches of water column for natural gas on most residential models (3.5 to 11 for one 20 kW model) and 7 to 11 inches for LP, measured at the generator inlet. The installer should measure it with the generator running at full load. If pressure drops below the minimum under load, the generator cannot reach rated output.
What paperwork should I keep from the gas side of the job?
Keep the utility's meter change confirmation, the gas permit and final inspection approval, the pressure test record, the installer's license number and the commissioning sheet showing inlet gas pressure at full load. These help with warranty claims, insurance questions and a future sale, and they make troubleshooting faster if the generator ever struggles under load.
Sources
- Manufacturer A Installation Manual TP-6803 (residential generators, 2/21)
- Manufacturer A Operation Manual TP-6804 (2/21)
- Manufacturer A Model Transfer Switch Manual TP-6807
- Florida City Gas, Maintaining Your Natural Gas Pipes
- Florida City Gas, Builders and Developers
- Florida Public Utilities, Building Projects
- Texas Occupations Code ch. 1301 (Plumbers)
- Texas State Board of Plumbing Examiners, License Types
- Texas Natural Resources Code ch. 113 (LP-gas)
- Railroad Commission of Texas, LP-Gas Safety Rules (16 TAC ch. 9)
- Texas Occupations Code ch. 1305 (Electricians)
- Florida Statutes 489.105 (2026), Definitions
- Florida Statutes 527.01 (2026), Definitions
- Texas S.B. 1252 (89th Leg., 2025), enrolled
- TDLR, SB 1252 changes (Aug. 14, 2025)
- Texas S.B. 1202 (89th Leg., 2025), enrolled
- FERC-NERC staff report, The February 2021 Cold Weather Outages in Texas and the South Central United States
- Homeyou, How Much Does Generator Installation Cost (Sept. 24, 2026)
- Inch Calculator, Backup Generator Cost Guide (Aug. 7, 2023)
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


