Local Guide · Standby generator installation
What Size Generator Do I Need? A Load Calculation Walkthrough for Your Home
How to size a standby generator from your real appliances: running vs starting watts, AC nameplates, fuel ratings, load management, and worked examples for a Houston and a Tampa home.
Add up the running watts of everything you want on at the same time, then add the extra starting surge of your single biggest motor, usually the central AC compressor, and leave a 20% cushion. Use the generator's rating on your fuel, since natural gas output is typically 10 to 15% lower than propane. Many 2,000 to 3,000 sq ft homes land at 18 to 22 kW, but two identical houses can differ by 8 kW or more, so size from your loads, not square footage.
Key facts
- Manufacturer B (Aug. 2026) says starting wattage is typically two to three times running wattage and sizes with: sum of running watts plus the highest single starting burst.
- Manufacturer C's method: sum running watts, add the largest motor's surge minus its running watts, then multiply by 1.20 for a 20% buffer.
- Manufacturer C lists a 3-ton central AC at 2,500 to 3,500 running watts and 6,000 to 10,000 starting watts; a 5-ton at 4,500 to 5,500 running and 12,000 to 15,000 starting.
- Manufacturer C says natural gas output is typically about 10% below the propane rating on its models and 10 to 15% across the industry; a 22,000 W propane unit makes about 19,800 W on natural gas.
- Manufacturer B says two homes with identical floor plans could need generators with an 8 kW gap or more.
- Manufacturer A's load management devices are designed to comply with the NEC's optional standby capacity rule (Section 702.5 in the 2008 NEC that Manufacturer A cites) and can manage up to six loads, including two independent AC loads.
- Texas adopted the 2026 National Electrical Code effective Sept. 1, 2026 (16 TAC 73.100; 51 TexReg 5776).
- Texas Utilities Code 39.107(b) says advanced meter data, including historical load data, belongs to the customer.
- EIA: the average U.S. residential customer bought 10,791 kWh in 2022, about 899 kWh a month.
The short answer: size from loads, not square footage
Generator size is measured in kilowatts (kW). One kW is 1,000 watts. The right size is the smallest generator that can carry everything you want running at the same time and start your biggest motor without stalling. In Texas and Florida that biggest motor is almost always the central air conditioner's compressor.
Manufacturer guides give square-footage shortcuts. Manufacturer B's August 2026 sizing page calls 18 to 22 kW "the sweet spot" for about 2,000 square feet and describes 22 kW as "the industry standard for whole-home protection" in 2,500 to 3,000 square foot homes. Manufacturer C groups homes into 8.5 to 14 kW for essential circuits under about 1,500 square feet, 14 to 22 kW for managed whole-home power at about 1,500 to 2,500 square feet, and 22 kW and up above 2,500 square feet.
Those ranges are a sanity check, not a decision. Manufacturer B itself says two homes with identical floor plans "could require generators with an 8kW gap or more." A 2,000 square foot house in Austin with a gas furnace, gas water heater and one 3-ton AC is a very different load from the same house with a heat pump, electric water heater, electric range and a pool pump. The rest of this page shows how to do the math yourself, so you can check any installer's number.
Running watts vs starting (surge) watts
Running watts are what a device uses once it is up and running. Starting watts, also called surge watts, are the short burst a motor needs to get moving. A compressor, well pump or fridge can draw several times its running power for a second or two at startup.
Manufacturer B says starting wattage is typically two to three times the running figure. That burst is what trips undersized generators: the engine slows, voltage dips, and the generator shuts down or the AC fails to start.
Lights, TVs, chargers and microwaves have little or no surge. Motors are the problem: AC compressors, air handler and furnace blowers, well pumps, sump pumps, pool pumps, refrigerators and freezers.
Typical appliance loads
These are one manufacturer's published typical figures (Manufacturer C). Your appliances may differ, so use your own nameplates when you can.
| Appliance | Running watts | Starting watts |
|---|---|---|
| Central AC, 3-ton | 2,500 to 3,500 | 6,000 to 10,000 |
| Central AC, 4-ton | 3,500 to 4,500 | 9,000 to 12,000 |
| Central AC, 5-ton | 4,500 to 5,500 | 12,000 to 15,000 |
| Mini-split | 600 to 1,500 | 1,800 to 3,000 |
| Refrigerator or freezer | 700 to 800 | 1,200 to 2,200 |
| Furnace blower motor | 800 | 2,300 |
| Well pump, 1/2 HP | 1,000 | 2,100 |
| Sump pump, 1/2 HP | 1,050 | 2,150 |
| Microwave | 1,000 | no surge |
| LED lighting, whole house | 150 to 300 | no surge |
Manufacturer C notes actual AC wattage "varies by SEER rating, age, and whether the unit has a soft start." For water heaters, ranges, dryers, pool pumps and heat strips, read the wattage or amps on the nameplate. To turn amps into watts, multiply amps by volts: a 240-volt appliance labeled 20 amps draws about 4,800 watts.
Step by step: how to calculate your generator size
This is the method most manufacturer guides use. Manufacturer C's version adds a 20% buffer; Manufacturer B's does not, so we include it as a cushion for heat, aging equipment and loads you forgot.
- List the loads you want. Go room by room. Split them into must-have (fridge, AC, medical devices, well pump, lights, internet), nice-to-have (second AC, electric oven, dryer, pool pump) and skip.
- Find running watts. Use the nameplate, the owner's manual, or the typical figures above.
- Find starting watts for each motor. For the AC, find the locked rotor amps on the condenser nameplate (see the next section).
- Add all running watts for loads that could be on at the same time.
- Add the surge of the single largest motor. Manufacturer C uses the surge minus the running watts (the extra above running). Manufacturer B adds the whole highest starting figure, which is more conservative. Only the biggest one counts, because motors rarely start at the exact same instant, and load management can enforce that.
- Add 20%.
- Compare with the rating on your fuel. A generator advertised as 22 kW on propane may make closer to 19.8 kW on natural gas, per Manufacturer C.
Manufacturer C's worked example: running loads of 5,850 W plus a 6,500 W AC surge (10,000 W start minus 3,500 W running) equals 12,350 W. Times 1.20 equals 14,820 W, or about a 15 kW generator.
What "diversity" means
Not everything runs at once. Your AC cycles, the fridge cycles, the dryer runs for an hour. Electricians call this load diversity. The NEC's load calculation rules (Article 220) build in demand factors for this when sizing a service. For a generator, you control diversity yourself: decide which big loads you will never run together, and if you cannot trust the household to remember, use load management to enforce it.
How to read your AC nameplate: LRA, RLA and MCA
The data plate on your outdoor AC or heat pump unit holds the numbers that matter most for sizing. Look for:
- RLA (rated load amps): the compressor's running current under rated conditions.
- LRA (locked rotor amps): the current the compressor draws at the instant of startup, before the motor turns. This is the surge you must cover.
- MCA (minimum circuit ampacity): what the circuit wire must carry. It includes the compressor and the outdoor fan.
- Voltage: almost always 208/230 volts for central AC.
To estimate starting watts, multiply LRA by voltage. For example, if your nameplate reads LRA 100 at 240 volts, the startup draw is about 24,000 volt-amperes for a fraction of a second. That is a worst case: the real surge is shorter and the generator's alternator can briefly exceed its rating. Generators handle motor starting differently, which is why installers look at the manufacturer's motor-starting data and not just the kW rating. Manufacturer A, for example, markets a separate excitation winding meant to support motor starting.
Running watts are roughly RLA times voltage. A compressor with RLA 14 at 240 volts runs near 3,400 watts, plus a few hundred watts for the outdoor fan and the indoor blower.
If you cannot read the plate, a photo sent to the installer is enough. Two units with the same tonnage can have very different LRA. Variable-speed (inverter) compressors start differently from single-speed ones, so ask the HVAC technician how yours behaves at startup. See our full guide to running central AC and heat pumps on a generator.
Can a generator run two AC units?
Yes, if it is sized for both compressors running plus one starting at a time. The usual approach is load management: the generator controller lets the second AC start only when there is enough spare capacity, and sheds it first if the load climbs. Manufacturer A's load management device, for example, includes two relays to control two independent air conditioner loads and can manage up to six loads in total.
Can I size a generator from my electric bill or smart meter data?
Your bill shows total kilowatt-hours (kWh) for the month, which is energy, not peak power. A generator has to meet your highest moment of use, not your average. EIA says the average U.S. residential customer bought 10,791 kWh in 2022, about 899 kWh a month. Spread evenly, that is only about 1.2 kW, but every home has short peaks many times higher, when the AC, dryer and oven overlap. So a monthly bill alone will badly undersize a generator.
Interval data is much better
Smart meters record usage in short intervals. If you can see your usage hour by hour or in 15-minute blocks, look at your hottest summer afternoons and, in Texas, your coldest winter mornings. The highest interval tells you what your home actually drew when everything you normally run was on. Multiply a 15-minute kWh reading by 4 to get average kW over that interval (for example 2.5 kWh in 15 minutes is about 10 kW). Remember that intervals average out short motor surges, so you still need to add starting surge on top.
Texas: Texas Utilities Code 39.107(b) says meter data, including historical load data from advanced meters, belongs to the customer. In the competitive retail areas (including most of Houston and Dallas-Fort Worth), the statewide portal is Smart Meter Texas; check what interval detail your account shows. Customers of municipal utilities such as Austin Energy and CPS Energy in San Antonio, and of electric cooperatives, should look in their own utility's account portal.
Florida: Check your utility's online account (for example FPL, Duke Energy Florida, Tampa Electric or JEA) for hourly or daily usage charts. Detail varies by utility, so call if you cannot find interval data.
Meter data shows what you used with normal habits. During an outage you may want less (no pool pump) or more (heat strips during a freeze, if you normally heat with gas but plan to run space heaters). Use the data as a check on your calculation, not a replacement for it.
NEC load calculation vs a measured peak: which do installers use?
There are two common ways to size a standby system:
- A calculated load. The installer lists your loads from nameplates and applies demand factors, similar to the National Electrical Code's Article 220 method for sizing a service. This tends to be conservative.
- A measured or observed peak. The installer uses meter data or a recording meter to see your real peak, then adds motor surge and margin.
For an automatically transferred optional standby system (the NEC term for a home generator that is not legally required), Article 702 sets the capacity rule. In short, the generator must be able to carry the full load the transfer switch connects to it, unless an automatic load management system keeps the load within the generator's capacity. Manufacturer A's installation manual says its load management devices "provide an automatic load management system to comply with Section 702.5 of NEC 2008." Section numbers have moved in later code editions, so ask your installer or inspector for the exact citation in the edition your jurisdiction enforces.
Which edition applies? Texas adopted the 2026 NEC effective September 1, 2026 under 16 TAC 73.100 (51 TexReg 5776). Florida enforces the NEC through the Florida Building Code: the 8th Edition (2023), in effect since December 31, 2023, uses the 2020 NEC, and the 9th Edition, based on the 2023 NEC, is scheduled to take effect December 31, 2026, though some cities have announced January 1, 2027, so confirm which edition your permit application falls under. Section numbers in this guide may have been renumbered in the edition your jurisdiction enforces. In Texas, S.B. 1252 (2025) limits city amendments to the NEC for residential energy backup systems up to 50 kW, but TDLR says the work must still follow the NEC and be done by licensed electricians.
The practical takeaway: if your generator is smaller than the full load behind a whole-house transfer switch, expect the installer to include load management. That is a code issue, not an upsell.
Fuel, heat and altitude: why the label number is not what you get
Natural gas vs propane rating
Most home standby generators are rated higher on propane than on natural gas. Manufacturer C says natural gas output is typically about 10% lower on its models and 10 to 15% lower across the industry. Its example: a 22,000 W propane unit produces about 19,800 W on natural gas. Manufacturer A's manual notes that converting fuel "will change the generator set rating" and directs installers to the specification sheet for ratings on each fuel. Always size against the rating on the fuel you will actually use.
Gas supply matters too. Manufacturer C warns that low gas pressure or an undersized or long gas line can reduce output further under heavy load. Manufacturer A lists required supply pressure of 5 to 11 inches of water column on natural gas (3.5 to 11 on its 20 kW model) and 7 to 11 on propane. See natural gas vs propane generators.
Heat and altitude
Engines make less power in hot, thin air. Manufacturers publish derating factors for high temperature and altitude on each model's specification sheet. We could not verify a current published derating figure for residential models, so we do not quote one. Ask the installer to show you the derating note on the spec sheet for the model you are considering.
Altitude is a small factor in Texas and Florida homes outside far West Texas. Heat is not. A generator sitting in direct sun on a 98 F Houston afternoon is working in the conditions where your AC load is highest. If your calculation lands right at the generator's limit, step up a size or add load management.
Load shedding, load management and soft starters
These tools let a smaller generator do more.
- Load management (load shedding). Modules that switch big loads off when the generator nears its limit and back on when capacity returns. Manufacturer A describes its system as monitoring the generator and adding or shedding loads in order of priority, which allows "the use of a smaller generator set than would be needed to run all of the building's electrical equipment at the same time." Manufacturer B's load manager "temporarily pauses lower-priority loads when the system nears overload." Homeyou's 2026 guide prices load management at $749 to $2,808.
- Soft starters. Devices added to an AC compressor that ramp up its startup current instead of hitting the full locked rotor draw. Manufacturer C and Manufacturer B both mention soft starters as a way to run a larger AC on a smaller unit; Manufacturer B suggests pairing a 14 or 18 kW unit with a load manager or soft start kit for a 3-ton AC. Neither publishes a guaranteed surge reduction. Check your AC manufacturer's warranty terms before adding one, and have an HVAC technician install it.
- Priority settings. Decide what gets shed first. Typically: pool pump, dryer, electric water heater and a second AC go first; the main AC, fridge and medical loads go last.
Load management changes the comparison from "how big must the generator be to run everything at once" to "how big must it be to run what I need while it takes turns with everything else." See whole-house vs essential circuits.
What happens if the generator is too small or too big?
Undersized
- The AC fails to start, or the generator shuts down on overload or low frequency. Manufacturer A's fault list includes shutdowns when engine speed or frequency drops too far, with the instruction to "reduce the load."
- Lights dim and motors hum during starts, which is hard on compressors and electronics.
- You end up shutting things off by hand during a heat wave or freeze, which defeats the point of an automatic system.
Oversized
- You pay more up front for the unit, transfer equipment and fuel line.
- You burn more fuel than needed. Manufacturer A's 20 kW unit uses about 161 cubic feet per hour of natural gas at 50% load versus 124 for its 14 kW unit at 50% load.
- A large propane unit drains a tank faster, which matters when deliveries stop after a storm. See propane tank size and runtime.
A modestly oversized unit is usually safer than an undersized one, because loads grow over time. But "buy the biggest" is not a plan. Load management often gives better value than a jump of one or two sizes.
Texas: size for February, not just August
In most of Texas, the summer AC load drives sizing. But Winter Storm Uri showed the other extreme. The FERC-NERC report says more than 4.5 million people in Texas lost power, some for as long as four days, while exposed to below-freezing temperatures for over six days. Texas DSHS counted 246 storm-related deaths, 158 of them from hypothermia.
Many Texas homes heat with a heat pump that relies on electric resistance heat strips when it is very cold. Heat strips are rated in kilowatts on the air handler label, and they can draw more than the AC does in summer. A home with a heat pump and large heat strips can need far more generator capacity in a hard freeze than on the hottest August day. If you want heat during a Uri-type event, run your load calculation twice: once for summer cooling and once for winter heating with strips. Then decide whether to size up, use load management to limit strip stages, or plan on a gas or other backup heat source. Our AC, heat pump and heat strip guide walks through it.
Rural Texas homes should also count freeze-protection loads like well house heat lamps or heat tape, and the well pump itself. See generators for well pumps and septic.
Florida: year-round AC, pools and heat
Florida loads are dominated by air conditioning most of the year, with pool pumps and, in rural North and Central Florida, well pumps on top. After a hurricane, outages often come with heat and humidity, and keeping at least one AC zone running protects health and helps prevent mold. Heat also works against the generator: the engine is producing power in the same hot air that drives the AC load. If your calculation is close to the limit, add margin. See our Florida hurricane generator guide.
Worked example 1: 1,800 sq ft Houston home with a 3-ton AC
This is an illustration using Manufacturer C's typical figures and assumed nameplate values. Your numbers will differ.
The home has a gas furnace, gas water heater and gas range, one 3-ton AC, a fridge, a chest freezer, LED lighting, a microwave, internet and TVs. The owner wants the whole house cooled during a Beryl-type outage, with no dryer or oven use.
| Load | Running watts (assumed) |
|---|---|
| 3-ton AC compressor and outdoor fan | 3,500 |
| Air handler blower | 800 |
| Refrigerator | 800 |
| Chest freezer | 700 |
| LED lighting | 300 |
| Microwave | 1,000 |
| Internet, TVs, chargers, fans (assumed) | 600 |
| Total running | 7,700 |
Largest surge: the AC at up to 10,000 W starting, 6,500 W above its running watts. 7,700 + 6,500 = 14,200 W. Add 20%: about 17,000 W, or 17 kW.
On natural gas, a unit sold as 18 kW (on propane) might make about 16 kW, using Manufacturer C's 10% rule of thumb. That is slightly short. Options: step up to the next size, add a soft starter to the AC and re-check the starting draw, or use load management so the microwave cannot run while the AC starts. Manufacturer B's guidance for a 3-ton AC suggests a 14 or 18 kW unit with a load manager or soft start kit, so an installer could reasonably propose any of these.
Worked example 2: 3,500 sq ft Tampa home with two ACs and a pool
Again, an illustration using Manufacturer C's typical figures and assumed nameplate values.
The home is all-electric: a 4-ton AC upstairs and a 3-ton AC downstairs, electric water heater (assume 4,500 W from the nameplate), electric range, a pool pump (assume 1,500 W running from its label), two fridges and normal household loads.
| Load | Running watts (assumed) |
|---|---|
| 4-ton AC | 4,500 |
| 3-ton AC | 3,500 |
| Two air handler blowers | 1,600 |
| Two refrigerators | 1,600 |
| Pool pump | 1,500 |
| Electric water heater | 4,500 |
| Lighting, electronics, microwave | 2,000 |
| Total running | 19,200 |
Largest surge: the 4-ton AC at up to 12,000 W starting, 7,500 W above running. 19,200 + 7,500 = 26,700 W. Add 20%: about 32 kW. That is beyond many air-cooled home units.
Now apply load management. Put the pool pump, water heater and the 3-ton AC on shed relays so they run only when there is room. The "always on" running load drops to about 10,700 W (4-ton AC, two blowers, two fridges, lights and electronics). Add the 4-ton surge of 7,500 W: 18,200 W, plus 20% is about 22 kW. With priority loads managed, a unit near 22 to 24 kW on the fuel being used could keep the house livable, with the shed loads taking turns. If the home runs the generator on propane, it also gets the unit's higher propane rating.
The lesson: in a big all-electric Florida home, load management is often the difference between a standard home unit and a much larger, costlier one.
Should I size for an EV, an addition or a future heat pump?
Plan for the next five to ten years. A Level 2 EV charger can draw as much as a large AC, and adding one later to a generator sized with no margin means either never charging during an outage or shedding the charger automatically. A future heat pump replacing a gas furnace changes your Texas winter math. If you expect these changes, either buy one size larger now or choose a transfer switch and generator that support load management so the new load can be added to a shed relay. Ask your installer to note future loads on the load calculation. Manufacturer B lists an EV charger among the "heavy hitter" loads in its sizing guide.
How to choose a provider
- Walk the house and list every load you want during an outage, grouped into must-have, nice-to-have and skip.
- Photograph the nameplate on each AC condenser, air handler, well pump, pool pump and water heater.
- Write down running watts for each load and the starting watts or LRA for each motor.
- Add running watts, then add the single largest starting surge, then add a 20% cushion.
- Check the result against the generator's rating on your fuel (natural gas or propane), not the headline number.
- Pull your highest-use days from your utility's smart meter data and compare the peak with your calculation.
- Decide whether load management or a soft starter lets you buy one size smaller.
- In Texas, repeat the calculation for a freeze: heat pump plus heat strips, not just summer AC.
- Ask installers for a written load calculation and the method they used before you compare prices.
- Allow room for loads you plan to add in the next few years, such as an EV charger or an addition.
Related standby generator installation guides
- Whole-House vs Essential-Circuit Generators: Which Setup Do You Actually Need?
- Can a Generator Run My Central AC? Sizing for AC, Heat Pumps and Heat Strips
- Generators for Well Pumps, Septic Lift Pumps and Sump Pumps
- How Much Does a Whole-House Standby Generator Cost Installed in Texas and Florida?
- Natural Gas vs Propane Generators: Cost, Runtime, Reliability and Which Is Right for You
- Automatic Transfer Switches Explained: Service-Rated, Load-Shedding and Smart Management
- Generators for Medical Equipment: How Do You Keep Oxygen, CPAP and Other Devices Running in a Texas or Florida Outage?
- Do You Need a Generator in Texas? ERCOT, Winter Storm Uri, Beryl and Outage Risk by City
Standby generator installation by state and city
Questions people ask
Is a 22 kW generator enough for a 2,500 sq ft home?
Often, but not always. Manufacturer B calls 22 kW the industry standard for whole-home protection in 2,500 to 3,000 sq ft homes, depending on how many high-draw appliances run at once. A gas-heated home with one or two ACs and load management usually fits. An all-electric home with two large ACs, an electric water heater and a pool pump may not, unless big loads are managed. Remember a 22 kW propane rating may be closer to 19 to 20 kW on natural gas.
What size generator runs a 4-ton or 5-ton AC?
Manufacturer C lists a 4-ton AC at 3,500 to 4,500 running watts and 9,000 to 12,000 starting watts, and a 5-ton at 4,500 to 5,500 running and 12,000 to 15,000 starting. It says larger 4 to 5 ton systems often push toward 22 kW and up unless you add a soft starter or load management. Check your compressor's locked rotor amps on the nameplate, since startup draw varies by model.
Does load shedding let me buy a smaller generator?
Yes. Load management switches off lower-priority loads when the generator nears its limit and restores them when capacity returns. Manufacturer A says this allows a smaller generator than would be needed to run everything at once. Under the NEC's optional standby rules, a generator smaller than the full load behind an automatic transfer switch generally needs automatic load management. Homeyou's 2026 guide prices load management at $749 to $2,808.
How much power does a refrigerator, well pump or sump pump use?
Manufacturer C's typical figures: a refrigerator or freezer runs at 700 to 800 watts and needs 1,200 to 2,200 watts to start; a 1/2 HP well pump runs at about 1,000 watts and starts at about 2,100; a 1/2 HP sump pump runs at 1,050 and starts at 2,150. Larger well pumps need much more. Check the nameplate or manual for your exact unit, especially for deep-well 240-volt pumps.
What size generator do I need for a home with electric heat strips?
Read the heat strip rating on the air handler label; strips are listed in kilowatts. Add that to your other winter loads, plus the heat pump compressor if it runs with the strips. In a Texas freeze this can exceed your summer AC load. Many owners size for summer and then limit heat strip stages with load management, or plan another heat source. Run the calculation for both seasons before you buy.
Does natural gas reduce my generator's output?
Usually. Manufacturer C says natural gas output is typically about 10% below the propane rating on its models and 10 to 15% across the industry, so a 22,000 W propane unit makes about 19,800 W on natural gas. Low gas pressure or an undersized line can cut output further under heavy load. Manufacturer A says converting fuel changes the rating and that installers should check the specification sheet for each fuel.
Can I use a sizing calculator from a generator brand?
You can, as a rough starting point. Manufacturer calculators and square-footage charts do not know your AC's locked rotor amps, your fuel, or which loads you will manage. Manufacturer B's own sizing page recommends a site survey for a precise load analysis. Use the calculator, then do the step-by-step math on this page with your real nameplates, and ask the installer to show their written calculation.
Who is allowed to do the load calculation and install the generator?
Anyone can do a rough calculation, but the installation is licensed work. In Texas, TDLR says electrical work on residential backup systems must follow the NEC and be done by licensed electrical contractors, even after S.B. 1252. In Florida, a licensed electrical contractor does the work unless a homeowner qualifies for the owner-builder exemption. Gas or propane connections need a licensed plumber or LP-gas installer in both states.
Sources
- Manufacturer B, What Size Generator Do I Need? (Aug. 9, 2026)
- Manufacturer C, What Size Home Standby Generator Do I Need?
- Manufacturer A Installation Manual TP-6803 (residential generators, load management devices)
- Manufacturer A Operation Manual TP-6804 (residential generators)
- 16 Tex. Admin. Code 73.100, Technical Requirements (2023 NEC adoption)
- Florida Building Commission, Florida Building Code 8th Edition (2023)
- Texas Utilities Code ch. 39 (Sec. 39.107, metering and meter data)
- Smart Meter Texas
- U.S. EIA, How much electricity does an American home use?
- FERC-NERC Staff Report, The February 2021 Cold Weather Outages in Texas and the South Central United States
- Texas DSHS, February 2021 Winter Storm-Related Deaths
- TDLR, SB 1252 changes to residential energy backup system regulations (Aug. 14, 2025)
- Homeyou, How Much Does Generator Installation Cost (updated Sept. 24, 2026)
- Florida Statutes 489.503 (electrical contracting exemptions)
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


