New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Fri, Nov 20, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · AC and heating

Why Is My AC Running but Blowing Warm Air?

How to tell a simple settings or airflow problem from a failed capacitor, a refrigerant leak or a system that is just at its limit on a 105°F Texas afternoon, with safe self-checks and what a repair visit should include.

If your AC runs but blows warm air, start with the thermostat: it must be on Cool with the fan on Auto, because a fan set to On blows uncooled air between cycles. Next, replace a dirty filter and check that the outdoor unit's fan and compressor are running. If the outdoor unit is silent or humming, a failed capacitor or contactor is a common cause. Ice on the lines points to low airflow or a refrigerant leak. Electrical and refrigerant repairs need a licensed technician.

Key facts

  • Carrier says a thermostat fan set to On runs constantly and can blow warm air; set it to Auto (Carrier).
  • Carrier says AC capacitors typically last about 10 to 20 years (Carrier).
  • Carrier warns capacitors are high-voltage components and homeowners should not troubleshoot electrical issues themselves (Carrier).
  • ENERGY STAR says airflow problems can reduce system efficiency by up to 15% (ENERGY STAR).
  • ENERGY STAR estimates 20% to 30% of the air moving through a typical duct system is lost to leaks, holes and poor connections (ENERGY STAR).
  • Texas averaged 17.2 days a year at 100°F or higher from 1900 to 2024 (NOAA State Climate Summary 2025).
  • Florida's energy code caps cooling equipment at 1.15 times the calculated load and bans safety factors in sizing (FBC-Energy R403.7.1).
  • Only EPA Section 608 certified technicians may buy refrigerant for home AC systems (EPA).
  • Trane's 2026 guide puts installed central AC replacement at $6,568 to $13,669 depending on tier, a national manufacturer estimate (Trane).

Start here: the five-minute self-check

Warm air from the vents has many causes, but you can rule out the easy ones in five minutes. Do these in order:

  1. Thermostat mode: It must say Cool. Carrier suggests Auto if you are unsure of the right mode.
  2. Fan setting: Set it to Auto. On On, the blower runs nonstop. Between cooling cycles it pushes air that has not been cooled, which feels warm, and in humid Florida and Gulf Coast homes it can also blow moisture off the wet coil back into the house.
  3. Setpoint: Set it at least 3 degrees below the room temperature so the system actually calls for cooling.
  4. Filter: Replace it if it is gray and dense. A blocked filter can make the coil freeze and the air go warm.
  5. Outdoor unit: Go outside while the system runs. The fan on top should spin and you should hear the compressor running. Warm air should blow up out of the top.

If all five check out and the air is still warm after 15 minutes, the problem is mechanical, electrical or refrigerant-related. Keep reading to narrow it down, but do not open the unit.

The main causes, ranked from easiest to most serious

CauseCluesDIY or pro
Thermostat fan on On, wrong mode or setpointAir is lukewarm between cycles; outdoor unit off while blower runsDIY
Dirty filter or blocked returnWeak airflow, frost on lines, dusty registersDIY
Tripped outdoor breaker or pulled disconnectIndoor fan runs, outdoor unit silentDIY reset once, then pro
Dirty outdoor condenser coilUnit runs constantly, top air very hot, higher bills, trips on hot afternoonsLight rinse DIY with power off; deep cleaning pro
Failed run capacitorOutdoor unit hums, fan does not spin, or fan spins slowlyPro
Failed contactorOutdoor unit silent though thermostat calls; or unit will not shut offPro
Frozen evaporator coilIce on the copper line, water around air handler after thawTurn off, thaw, then pro if it repeats
Refrigerant leak (low charge)Long run times, ice, hissing, gradual decline in coolingPro only
Duct leak or disconnected ductSome rooms warm, attic very cold or dusty, one vent weakPro, or careful DIY with mastic
Compressor failureFan runs but compressor never starts; repeated breaker tripsPro; often a repair-or-replace decision
System at its design limitAir is cool but the house drifts above setpoint on the hottest afternoonsUsually normal; see design limits below

Capacitors and contactors: the most common outdoor failures

The outdoor unit holds two small electrical parts that fail often in hot climates.

The capacitor

A run capacitor is a metal can that stores and releases energy to start and run the compressor and outdoor fan motor. When it weakens, the motors struggle to start. You may hear a hum or buzz while the fan sits still, or see the fan turn slowly. Carrier says AC capacitors typically last about 10 to 20 years. Heat speeds up the wear, which is one reason Texas units on long 100°F stretches lose capacitors in July and August.

The contactor

A contactor is a relay. When the thermostat calls for cooling, a low-voltage signal pulls the contactor closed, sending full power to the outdoor unit. If its contacts burn or pit, the outdoor unit may not start. If the contacts weld shut, the unit may run even when the thermostat is off. Ants and other insects sometimes nest in contactors, a common nuisance in warm, humid areas.

Can I replace an AC capacitor myself?

We do not recommend it. Carrier warns that capacitors are high-voltage parts and that homeowners should not troubleshoot electrical issues themselves. A capacitor can hold a dangerous charge after the power is off. It also has to match the right microfarad rating and voltage, and a wrong part can damage the compressor. In Texas, AC repair for the public must be done by or under a TDLR-licensed contractor; in Florida, by a DBPR-licensed contractor. A licensed technician will test the capacitor with a meter, not just swap parts.

Also ask: why did it fail? A capacitor that fails after a few years may point to a dirty condenser coil, a failing fan motor, or voltage problems.

Dirty condenser coils and coastal corrosion

The outdoor coil is where the heat from your house leaves. Grass clippings, dryer lint, cottonwood fluff, dust and pollen mat onto the fins. The unit then cannot shed heat, pressures rise, the compressor works harder, and on the hottest afternoons cooling falls off or a high-pressure safety trips.

What you can do with power off at the disconnect:

  • Clear leaves and debris from around the unit and keep shrubs trimmed back.
  • Gently rinse the outside of the coil with a garden hose, from the inside out if the cover allows without disassembly. Never use a pressure washer, which flattens fins.
  • Keep nothing stored on top of the unit.

A deep cleaning with coil cleaner is part of a professional tune-up. ENERGY STAR recommends a contractor check the cooling system every spring.

In coastal Florida and on the Texas Gulf Coast, salt air corrodes aluminum fins, copper tubing and electrical terminals. Corroded fins flake and lose contact with tubes, which cuts heat transfer, and corrosion at the contactor and wiring can cause intermittent failures. Rinsing salt off the coil with fresh water helps. See our coastal corrosion guide for coatings and placement options.

Is warm air a sign of low refrigerant?

Sometimes, but it is not the first thing to assume. Refrigerant runs in a sealed loop. It is not used up like gas in a car, so a system that is low has a leak or was undercharged at installation. Signs of a low charge include long run times, cooling that gets gradually worse over weeks, ice on the larger copper line, and sometimes a hissing sound. Lennox also lists higher humidity and higher bills as signs.

Two things matter for you:

  • Topping off is not a fix. Adding refrigerant to a leaking system buys time. The leak continues, and you pay again.
  • Only certified technicians may handle it. Federal rules limit refrigerant sales for home AC to EPA Section 608 certified technicians, and intentional venting is illegal.

If your system uses R-22, which ended U.S. production and import in 2020, recharging is legal but expensive, and a leak is often the point at which people decide to replace. For R-410A systems, EPA's May 2026 rule removed the installation deadline for pre-2025 equipment, and EPA has said R-410A for recharging is likely to rise in price as the phasedown continues. Newer systems use R-454B or R-32, and you cannot mix refrigerants. Full detail is in our refrigerant leak guide.

Is your AC broken, or just at its limit on a 105°F day?

This is the question most guides skip. A home AC is not designed to hold 72°F on the hottest day ever recorded. It is designed for a design condition: an indoor target and an outdoor temperature that is hot but not extreme for your city. Industry load calculations (ACCA Manual J) use local design temperatures from climate tables, and the outdoor design number is below the peak temperatures a city sees in its worst heat waves.

Florida makes this explicit in code. The Florida energy code requires equipment sized with ACCA Manual S from a Manual J load, at the design conditions in the code, and it forbids adding safety factors (FBC-Energy R403.7.1). Cooling-only equipment can be no more than 1.15 times the calculated load (R403.7.1.1). That rule exists because oversized systems short cycle and leave homes humid.

Texas weather routinely exceeds typical design conditions. Texas averaged 17.2 days a year at 100°F or more over 1900 to 2024, and the state's record is 120°F. Houston's record is 109°F. On those afternoons a properly sized system may run nonstop and the house may climb a few degrees above the setpoint by late afternoon, then recover in the evening. That is normal behavior, not a failure.

How to tell the difference

  • At its limit: air from the vents is clearly cold, the outdoor unit runs, and the house catches up after sunset.
  • Something is wrong: air from the vents is barely cool, the house never catches up even overnight, or performance has gotten worse compared with last summer at similar temperatures.

Ask your contractor for the Manual J report used to size your system, including the outdoor design temperature. If none was done, your system may be oversized or undersized. Our Manual J sizing guide explains what to ask for.

The temperature drop check (delta T): a rough self-test

You can estimate how well the system is cooling with an inexpensive digital thermometer:

  1. Let the AC run for at least 15 minutes.
  2. Measure the air at the return grille (where air goes in).
  3. Measure the air at a supply vent close to the indoor unit.
  4. Subtract. That difference is often called the delta T or temperature split.

Technicians commonly use a rough rule of thumb of about 15 to 20°F of drop for a central system in cooling mode. We could not confirm this range in an ACCA standard or other primary source, so treat it as a rough guide, not a pass or fail test. The right number depends on humidity, airflow and the equipment. In very humid weather the split is usually smaller, because the system is spending more of its effort removing moisture.

How to use the result:

  • A split of only a few degrees with the outdoor unit running points to a refrigerant, compressor or airflow problem. Call a technician.
  • A good split but a warm house points to duct leaks, the design limit, or heat gain through the attic.
  • A very large split with weak airflow can mean a clogged filter or a dirty indoor coil, which can lead to freezing.

Write down your readings and the outdoor temperature. They help the technician and help you compare year to year.

Cold in one room, warm in another

If some rooms get cold air and others do not, the equipment is probably working and the problem is in the duct system. ENERGY STAR estimates that 20% to 30% of the air moving through a typical home's ducts is lost to leaks, holes and poor connections. In Texas and Florida, most ducts run through hot attics, so a disconnected or crushed duct can dump cold air into a 130°F attic.

Check:

  • Are all supply registers open and unblocked?
  • Is there a manual damper on a duct near the air handler that has been closed?
  • Do warm rooms have a return path, such as a return grille or enough gap under the door?
  • Can you see a disconnected duct from the attic access? Do not walk on ceiling drywall.

ENERGY STAR advises sealing ducts with mastic or metal tape, never cloth duct tape. Florida's code requires attic ducts to be insulated to at least R-8 for ducts 3 inches or more in diameter. Our duct leak guide and upstairs too hot guide go further.

Warm air at night, or only cooling to 78

Warm air at night

If the system cools by day but blows warm at night, check for a thermostat schedule or eco setting that raises the setpoint overnight. If the outdoor unit stops at night while the blower runs, suspect an electrical issue such as a weak capacitor or failing contactor, or a frozen coil. Coils sometimes freeze in the evening when the load drops and airflow is restricted. If you find ice, see our frozen coil guide.

Only cooling to 78°F

If the house will not drop below 78 on a mild day, the system has lost capacity. Common reasons are a dirty indoor or outdoor coil, a low refrigerant charge from a leak, leaky ducts, or a failing compressor. If it only stalls at 78 during a 100°F+ afternoon and recovers at night, it may simply be at its design limit, as explained above.

How long should an AC take to cool a house?

It depends on size, insulation and how hot the house got. Carrier says a healthy system typically runs in cycles of about 15 to 20 minutes. If you let a house heat up to 90°F while away, recovery can take hours on a hot afternoon, and a correctly sized system recovers more slowly than an oversized one. That is one reason very large setbacks in Texas and Florida summers can backfire on comfort.

What a repair visit should include

A good diagnostic visit for warm air should cover, at minimum:

  • Thermostat operation and wiring.
  • Voltage at the outdoor unit and testing of the capacitor and contactor with a meter.
  • Outdoor fan motor and compressor amperage.
  • Indoor airflow: filter, blower, evaporator coil condition.
  • Refrigerant pressures and superheat or subcooling compared with the manufacturer's chart.
  • The condensate drain and float switch.
  • A written explanation of the cause, the repair price, and the parts used.

If a technician recommends refrigerant without looking for a leak, ask why. If the system is old and the repair is large, ask for the price of the repair and a replacement quote side by side. Our repair or replace guide lays out the math.

What do repairs cost?

Honest answer: it depends on the part, the system and the company, and many cost figures online are from lead-generation sites that do not publish their methods. We could not load an independent, dated Texas or Florida repair price study for this page, so we are not printing repair ranges here. Our AC repair cost guide collects the sourced numbers we can stand behind.

For scale, Trane's 2026 pricing guide estimates a complete installed central AC replacement at $6,568 to $8,544 for its single-stage tier, $8,573 to $10,671 for multi-stage, and $11,525 to $13,669 for variable-speed. Those are manufacturer-published national estimates for one brand, before tax, and local prices vary. Small parts like capacitors and contactors cost a fraction of that, so a correct diagnosis matters.

Tips to keep repair costs fair:

  • Ask for the price before work begins and get it in writing.
  • Ask to see or keep the old part.
  • Ask whether parts are covered by the manufacturer's warranty. Many parts warranties require registration; see our warranty guide.
  • Compare a second opinion for any repair over a few hundred dollars on an older system.

Texas and Florida notes

  • Texas: Long runs of 100°F+ days in Dallas-Fort Worth, Austin and San Antonio stress capacitors, contactors and dirty coils. Attic air handlers in two-story homes face very hot attics, which adds heat to supply air through poorly insulated ducts.
  • Florida: Humidity is the bigger enemy. High latent load means smaller temperature splits and long run times. Coastal salt corrodes outdoor units in Miami, Tampa Bay and Jacksonville beach areas. Fan settings left on On re-humidify homes.
  • Both: Verify licenses with TDLR (Texas) or DBPR (Florida). Florida requires permits for HVAC change-outs even after the 2026 $7,500 owner exemption, which excludes mechanical work (§553.79).

See city pages: Dallas, Houston, Austin, San Antonio, Miami, Tampa, Orlando, Jacksonville.

How to choose a provider

  • Set the thermostat to Cool, fan to Auto, setpoint 3 or more degrees below room temperature.
  • Replace the air filter.
  • Confirm the outdoor fan spins and the compressor runs.
  • Look for ice on the copper lines; if present, turn cooling off and run the fan only.
  • Clear debris around the outdoor unit and rinse the coil gently with power off.
  • Measure return and supply air temperatures after 15 minutes and write them down.
  • Check that registers are open and returns are not blocked.
  • If the outdoor unit hums without the fan spinning, turn the system off and call.
  • Ask for a leak search, not just a refill, if refrigerant is low.
  • Get the diagnosis and price in writing before repairs.

Related ac and heating guides

AC and heating by state and city

Questions people ask

Why is my AC running but not cooling?

The most common reasons are a thermostat fan set to On, a dirty filter, an outdoor unit that is not running because of a tripped breaker, failed capacitor or contactor, a dirty outdoor coil, a frozen indoor coil, or a refrigerant leak. Start with the thermostat and filter, then check the outdoor unit. If the outdoor fan is not spinning or you hear humming, turn the system off to protect the compressor and call a licensed technician.

Can a bad capacitor cause warm air?

Yes. The run capacitor helps start and run the compressor and the outdoor fan motor. When it fails, the compressor may not start, so the indoor blower moves air that has not been cooled. You may hear the outdoor unit hum while the fan sits still. Carrier says capacitors usually last 10 to 20 years. Replacement is a job for a technician because capacitors are high-voltage parts that can stay charged.

Outdoor fan not spinning but compressor humming: what is wrong?

This usually means a failed capacitor or a seized outdoor fan motor. Without the fan, the compressor cannot shed heat and can overheat within minutes. Turn the thermostat off right away, and switch off the outdoor disconnect if you can do so safely. Do not push the fan blades with a stick to start it, a trick sometimes seen online, because the unit is energized and you risk injury and further damage.

How much does it cost to replace an AC capacitor or contactor?

These are among the least expensive AC repairs, but prices vary by company, region and time of call. We could not verify a current independent Texas or Florida price survey, so we do not print a range. Ask for a flat price before work begins, ask whether the diagnostic fee applies to the repair, and ask the technician to show you the meter reading or the failed part. Our repair cost guide tracks sourced figures.

What is a normal temperature drop across an AC?

Many technicians use a rough rule of thumb of about 15 to 20°F between return air and supply air in cooling mode, measured after the system has run 15 minutes. We could not confirm that range in a primary standard, and the right number varies with humidity and airflow. A very small split with the outdoor unit running suggests a problem; a normal split with a warm house suggests ducts, attic heat or a system at its design limit.

Why is the AC not keeping up when it is 100 degrees outside?

Home systems are sized for a local design temperature that is hot but not extreme. On afternoons above that design condition, which are common in Texas, a properly sized system can run nonstop and the house may drift a few degrees above the setpoint, then recover at night. If supply air is cold and the house recovers in the evening, that is normal. If the air is barely cool or the house never recovers, call for service.

Does my AC need Freon every year?

No. Refrigerant circulates in a sealed loop and is not used up. If a technician says your system needs refrigerant every year, it has a leak. Ask for a leak search and a repair estimate, and compare that to the cost of repeated recharges. Freon is a brand name usually associated with R-22, which is no longer produced or imported in the United States. Most systems installed in the last 15 years use R-410A, and new ones use R-454B or R-32.

Why does my AC blow warm air for a minute and then cold?

A short burst of warm air at startup is often normal, especially in attic duct systems where air sitting in the ducts heats up between cycles. If warm air continues for more than a few minutes, check the fan setting and whether the outdoor unit starts. A compressor time delay can also hold off the outdoor unit for a few minutes after a power interruption or a thermostat change.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration