Local Guide · AC and heating
What Size AC Do I Need? Manual J, Tonnage Myths and the Rule-of-Thumb Trap
Square feet per ton is a guess, and in humid Texas and Florida a bad guess costs you comfort. Here is how a Manual J load calculation works, what the codes require, and how to read your unit's size.
The right AC size comes from an ACCA Manual J load calculation, not square footage. Manual J adds up heat gain through walls, windows, roof, air leaks, ducts and people for your home and climate. Florida's energy code requires Manual J and Manual S sizing, bans safety factors, and caps cooling capacity at 1.15 times the calculated load. Texas's IECC-based code requires the same method, though local enforcement on replacements varies.
Key facts
- Florida's 2023 energy code requires residential HVAC equipment to be sized with ACCA Manual S based on Manual J or another approved method (FBC-Energy R403.7.1).
- Florida bans designer safety factors and 'future expansion' allowances in residential HVAC sizing (R403.7.1).
- In Florida, cooling-only equipment must be at least the calculated total load but no more than 1.15 times it (or the closest size offered), and latent capacity must meet the latent load (R403.7.1.1).
- Florida heat pumps must be sized on the cooling load, with cooling capacity no more than 1.15 times design cooling load even if heating load is higher (R403.7.1.2.1).
- Florida's interior design conditions for load calculations: a heating design temperature of no more than 72°F and a cooling design temperature of no less than 75°F (FBC-Energy R302.1).
- Texas adopted the energy chapter of the 2015 IRC as its single-family energy code effective Sept. 1, 2016 (Tex. Health & Safety Code 388.003); the matching IECC R403.7 requires Manual S sizing based on Manual J.
- Austin Energy rebates require ACCA Manual J or Austin Energy sizing guidance, and Oncor's program can require a Manual J depending on the unit.
- EPA recommends keeping indoor relative humidity below 60%, ideally 30% to 50%.
- ENERGY STAR says a contractor should verify system size using Manual J.
How many square feet per ton of AC? Why the rule of thumb fails
You will hear "one ton per 500 square feet," or 400, or 600. A ton of cooling is 12,000 Btu per hour. These rules of thumb take your floor area and divide. They are easy, and they are often wrong, because two houses with the same square footage can have very different cooling loads.
Compare two 2,000-square-foot homes:
| Factor | House A | House B |
|---|---|---|
| Built | 1978, original single-pane windows | 2020, low-e double-pane windows |
| Attic insulation | Thin, compressed | Thick, to current code |
| Ducts | Leaky flex in a hot attic | Tested and sealed, or inside the envelope |
| West-facing glass | Large sliders, no shade | Small, shaded |
| Air leakage | High | Low, tested |
A rule of thumb gives both houses the same size. A Manual J might give House A far more capacity than House B. If House B gets House A's system, it will be badly oversized.
The Air Conditioning Contractors of America (ACCA), which publishes Manual J, has long warned against rules of thumb. A post on ACCA's blog (October 2016) reported that 40 Manual J calculations averaged about 1,431 square feet per ton, far above the 400 to 600 square feet per ton many contractors use, and stated plainly: "you can't use square feet per ton to size air conditioners." Those homes were not all in Texas or Florida, so do not treat 1,431 as a local target; treat it as proof of how far guesses can drift. ENERGY STAR also says your contractor should verify the right size using Manual J.
Is 500 square feet per ton accurate? Sometimes it lands close, by luck. Many newer, tighter Texas and Florida homes need less capacity than that. Older homes with attic ducts may need more. The only way to know is to calculate.
What is a Manual J load calculation?
ACCA Manual J is the standard method for calculating a home's heating and cooling loads. It estimates how many Btu per hour of heat enter the house on a hot design day and leave it on a cold design day. Inputs include:
- Location and design conditions: outdoor design temperatures and humidity for your area, and indoor targets.
- Walls, roof and floors: area and insulation level.
- Windows and doors: size, glass type, direction and shading. West glass is a big summer load in Texas and Florida.
- Air leakage: from a blower door test if available, or an estimate.
- Ducts: location (attic or conditioned space), insulation and leakage.
- Internal gains: people and appliances.
- Ventilation: outside air brought in on purpose.
The output has two parts that matter in the South:
- Sensible load: heat that raises the air temperature.
- Latent load: moisture that has to be removed from the air. In humid Florida and Gulf Coast Texas, the latent load is a large share of the work an AC does.
A good Manual J report is room by room, so it also guides how much air each room needs. That feeds Manual D, the duct design.
What are Manual S and Manual D?
- Manual S is ACCA's method for selecting equipment that matches the Manual J loads. It uses the manufacturer's expanded performance data, not just the nominal tonnage, to check that the system delivers enough sensible and latent capacity at your design conditions without overshooting. A nominal "3-ton" unit may deliver more or less than 36,000 Btu/h depending on the indoor coil, airflow and outdoor temperature.
- Manual D is ACCA's method for designing ducts so each room gets the airflow its load requires, at a static pressure the blower can handle.
Think of it as J for the house, S for the equipment, D for the ducts. A system sized right by J and S can still underperform if the ducts are wrong. DOE's SEER2 test (appendix M1) raised the minimum external static pressure for conventional ducted systems to 0.5 inch of water column, up from 0.10 to 0.20 inch under the old SEER test, because stakeholders showed the old values were too low to represent field conditions. That makes ratings more realistic, but your actual ducts still decide what you get. See our duct guide.
Does Florida code require a Manual J?
Yes, for permitted work covered by the energy code. The 8th Edition (2023) Florida Building Code-Energy Conservation says:
- R403.7.1: heating and cooling equipment shall be sized with ACCA Manual S, based on loads from ACCA Manual J or another approved method, for the building's orientation. The outdoor and indoor model numbers must be submitted with the sensible and total cooling capacities at the design conditions in R302.1. Safety factors and future-expansion allowances are not allowed.
- R403.7.1.1: cooling-only equipment must have total capacity at least equal to the calculated total load, but no more than 1.15 times it, or the closest size the manufacturer offers. Latent capacity must at least meet the latent load.
- R403.7.1.2.1: heat pumps are sized on the cooling load, with cooling capacity no more than 1.15 times the design cooling load, even if the heating load is higher.
- R403.7.1.2.2: electric resistance furnaces must be sized within 4 kW of the calculated design load.
- R302.1: the heating design indoor temperature can be no more than 72°F and the cooling design indoor temperature no less than 75°F.
Replacements in existing Florida homes
Replacement HVAC equipment installed under a permit must meet the code's minimum efficiencies (R501.7), and Florida law states the Legislature's intent that replacement systems use quality installation procedures, including equipment sizing analysis and duct inspection (Fla. Stat. 553.912). How each building department applies the sizing documentation on a straight change-out varies, so ask your contractor what your county or city requires. Miami-Dade publishes residential mechanical plan review guidelines and an inspection checklist for the 2023 code.
Florida climate zones
Florida's code puts Miami-Dade, Monroe, Broward, Palm Beach, Collier, Lee and Hendry counties in Climate Zone 1A and every other county in Zone 2A, all warm-humid.
Does Texas require a load calculation for AC replacement?
On paper, the method is the same; in practice, enforcement varies.
- Texas adopted the energy efficiency chapter of the 2015 International Residential Code as the statewide energy code for single-family construction, effective September 1, 2016 (Tex. Health & Safety Code 388.003; U.S. DOE Building Energy Codes Program).
- The matching 2015 IECC residential section R403.7 requires heating and cooling equipment to be sized per ACCA Manual S based on loads calculated per ACCA Manual J, and requires new and replacement equipment to meet federal minimum efficiency for its location.
- Texas also adopts the International Residential Code as the municipal residential building code, as it existed May 1, 2012, and lets cities adopt later editions and local amendments (Tex. Local Gov't Code 214.212).
Cities issue mechanical permits for replacements. Houston, for example, requires a mechanical permit and inspection for condenser, evaporator and furnace replacements. Whether a city asks to see a Manual J on a change-out is a local practice; ask your contractor and your building department.
Rebates often require it regardless: Austin Energy requires sizing by Manual J or its own sizing guidance with proof attached, and Oncor's 2026 program can require a Manual J for single-family HVAC projects depending on the unit.
What happens if my AC is oversized?
Oversizing is the more common mistake, and in Texas and Florida it hurts in ways people do not expect.
- Humidity stays high. An AC removes moisture only while it runs long enough for the coil to get cold and drip. An oversized unit hits the thermostat setting fast and shuts off. The house feels cool but clammy. EPA recommends keeping indoor humidity below 60%, ideally 30% to 50%, to limit mold.
- Short cycling. Frequent starts wear the compressor and contactor. See our short cycling guide.
- Uneven rooms. Short run times do not mix air well, so distant rooms lag.
- Noise and drafts. More airflow than the ducts were built for.
- Higher price. You pay for capacity you do not need.
This is why Florida's code caps cooling capacity at 1.15 times the load and requires latent capacity to meet the latent load. See our humidity and mold guide.
What happens if my AC is too small?
An undersized system runs nearly nonstop on the hottest afternoons and may not hold the setpoint. Some signs:
- The house drifts several degrees above the setpoint during peak heat and recovers only after sunset.
- The system never cycles off on hot days.
A system sized to the design load is expected to run long and steady on design days. That is normal and good for humidity. Design temperatures are chosen so that only a small share of hours is hotter, so on the hottest days of a record summer, a correctly sized system may lose a degree or two. That is the trade-off for better dehumidification the rest of the year.
Before concluding the unit is too small, rule out problems that look like undersizing: low refrigerant from a leak, a dirty coil or filter, leaky attic ducts and a weak blower. See our blowing warm air guide and upstairs not cooling guide.
Does a bigger AC cool faster? Should I upsize when replacing?
A bigger AC drops the air temperature faster, but it does not cool the house better. Walls, furniture and moisture take time. A bigger unit reaches the setpoint and stops before it has removed humidity.
Should you upsize? Only if a new Manual J says so. Reasons the right size may change at replacement:
- Smaller: you added insulation, a radiant barrier, new windows or sealed ducts since the old unit was installed. Or the old unit was oversized.
- Larger: you added a room or enclosed a porch.
Florida's code forbids future-expansion allowances in sizing. If you plan an addition, size for the house as it will be when the system is installed, or plan a separate system for the addition. See our attic insulation guide.
What tonnage is my current AC? How to read the model number
Look at the nameplate on the outdoor unit. Many model numbers include a three-digit code for the nominal capacity in thousands of Btu per hour:
| Code in model number | Btu/h | Nominal tons |
|---|---|---|
| 018 | 18,000 | 1.5 |
| 024 | 24,000 | 2 |
| 030 | 30,000 | 2.5 |
| 036 | 36,000 | 3 |
| 042 | 42,000 | 3.5 |
| 048 | 48,000 | 4 |
| 060 | 60,000 | 5 |
Some brands use two digits (for example, 24, 36, 48) in a different position. If you are unsure, look up the model on the manufacturer's site or spec sheet. The nameplate also shows the refrigerant type.
Two cautions. First, the old unit's size tells you what was installed, not what the house needs. Second, the outdoor unit's nominal size and the system's actual capacity can differ depending on the indoor coil.
How much does a Manual J cost? Can I do one myself online?
We could not find a dated, independent source for Manual J prices in Texas or Florida, so we do not give a number. Many contractors include a load calculation in a replacement bid; others charge for it separately or credit it toward the job. Energy raters and HVAC design firms also offer them. Ask what the fee is and whether you get the full report.
Online calculators
Online load calculators can teach you what drives your load, and some use real Manual J methods. Their limits:
- They depend on what you type in. Guessing at insulation, air leakage, window types and duct leakage can swing the answer a lot.
- Many simple calculators are just square-feet-per-ton charts with a few multipliers.
- A homeowner's calculation may not be accepted for a Florida permit or a Texas utility rebate. Florida requires Manual J "or other approved" methods, and rebate programs set their own proof rules.
Use an online tool to check a contractor's result. If the two are far apart, ask the contractor to walk you through their inputs.
How do I know if my AC is the right size?
- Run time on hot afternoons: long, steady cycles are good. Running 5 to 10 minutes and shutting off on a 95-degree day suggests oversizing.
- Humidity: a hygrometer (an inexpensive humidity meter) should read under 60% indoors, ideally 30% to 50%, per EPA. Persistently higher readings with the AC running suggest oversizing, airflow set too high, or duct leaks pulling in humid air.
- Holding temperature: a right-sized system holds the setpoint on most days and may drift a degree or two only in extreme heat.
- Room-to-room balance: big differences usually point to ducts, not equipment size.
Questions to ask about the Manual J report
- What outdoor design temperatures and humidity did you use for my city, and what source? (We could not confirm a free, official city-by-city design temperature table to publish; ACCA's Manual J tables are the standard reference. Ask your contractor or building department.)
- What indoor conditions did you use? Florida's code calls for 75°F cooling and no more than 72°F heating.
- Did you measure the windows and walls, or estimate them?
- What did you assume for duct leakage and air leakage?
- What are the sensible and latent loads, and how does the selected equipment meet both?
Climate notes for Texas and Florida
- South Florida (Miami, Fort Lauderdale, West Palm Beach): Climate Zone 1A. High latent loads most of the year. Proper sizing and dehumidification matter more than raw cooling capacity.
- Central and North Florida (Orlando, Tampa, Jacksonville): Zone 2A. Similar summer humidity, with real winter heating hours. Heat pumps must still be sized on the cooling load under Florida's code.
- Houston and the Gulf Coast: long humid summers like Florida's. Latent capacity matters.
- Dallas-Fort Worth, Austin, San Antonio: hotter, sometimes drier peaks, plus colder winters. Gas furnaces are common in DFW, so heating sizing is a separate calculation from cooling.
- Panhandle and North Texas: the largest heating loads in either state.
Both states rank first and second in the lower 48 for population-weighted cooling degree days in 2024 and 2025 (NOAA). That is the strongest reason to get sizing right: your system runs more hours than almost anywhere else.
How to choose a provider
- Find your current unit's size from the model number on the outdoor nameplate.
- Ask every bidder whether they will do a Manual J, and request a copy.
- Ask what outdoor and indoor design conditions were used and why.
- Check that the report shows both sensible and latent loads.
- Ask for the Manual S selection: the equipment's capacity at your design conditions.
- In Florida, confirm the selected cooling capacity is no more than 1.15 times the load (or the next size offered).
- Do not accept a 'safety factor' or 'room for an addition' upsizing.
- Tell the contractor about upgrades since the old system went in: insulation, windows, duct sealing.
- Use a hygrometer to check indoor humidity before and after replacement.
- Fix duct leaks and airflow problems before blaming equipment size.
Related ac and heating guides
- How Do You Compare AC Replacement Quotes? A Line-by-Line Checklist for Texas and Florida
- How Much Does a New AC or Heat Pump Cost in 2026? What a Fair Texas or Florida Quote Includes
- How Do I Keep My Florida or Gulf Coast Home Below 60% Humidity and Stop AC Mold?
- Are Your Attic Ducts Leaking? How to Test, Seal or Replace Ductwork in Texas and Florida Heat
- AC Short Cycling, Strange Noises and Smells: What Do They Mean?
- Heat Pump or Gas Furnace in Texas and Florida: Which Heats Better and Cheaper?
- Do Attic Insulation and Radiant Barriers Cut AC Bills in Texas and Florida?
AC and heating by state and city
Questions people ask
What size AC do I need for my house?
The size your house needs comes from a Manual J load calculation that accounts for your insulation, windows, orientation, air leakage, ducts and local climate. Square-feet-per-ton rules can be far off in either direction. Ask contractors to perform a Manual J and share the report. In Florida, the energy code requires this method for permitted work.
How many square feet per ton of AC?
Rules of thumb range from about 400 to 600 square feet per ton, but they are not reliable. Two homes of the same size can need very different capacity depending on windows, insulation, ducts and air leakage. Newer, tighter homes often need less than these rules suggest. Use a Manual J instead.
Does Florida code require a Manual J?
Yes. The 2023 Florida Building Code-Energy Conservation, R403.7.1, requires residential heating and cooling equipment to be sized with ACCA Manual S based on loads from Manual J or another approved method. It bans safety factors and limits cooling capacity to 1.15 times the calculated load, or the closest size offered. Ask your building department how it documents this on change-outs.
What is the difference between Manual J, S and D?
Manual J calculates the home's heating and cooling loads. Manual S selects equipment whose real capacity at your design conditions matches those loads. Manual D designs ducts that deliver the right airflow to each room. All three are published by ACCA and work together; skipping one can undo the others.
Can an oversized AC cause mold?
It can contribute. An oversized AC cools the air quickly and shuts off before removing enough moisture, which can leave indoor humidity high. EPA recommends keeping indoor relative humidity below 60%, ideally 30% to 50%, to limit mold growth. Humid air from leaky attic ducts can make it worse.
Should I just replace my AC with the same size?
Not without checking. The old system may have been oversized from the start, and upgrades since then, such as new windows, insulation or duct sealing, can lower your load. An addition can raise it. A new Manual J tells you whether to keep, raise or lower the size.
Is a heat pump sized differently from an AC?
In Florida, heat pumps must be sized on the cooling load, with cooling capacity no more than 1.15 times the design cooling load even if the heating load is higher (FBC-Energy R403.7.1.2.1). Backup heat strips cover the gap on cold mornings. In colder North Texas, heating performance at low temperatures deserves a closer look during selection.
Sources
- Florida Building Code-Energy Conservation 2023, Chapter 4 Residential (R403.7)
- Florida Building Code-Energy Conservation 2023, Chapter 3 (R301.1 climate zones, R302.1)
- Florida Building Code-Energy Conservation 2023, Chapter 5 Existing Buildings
- Florida Statutes 553.912, Air conditioners
- Miami-Dade County, Mechanical Permits
- UpCodes, Texas IECC 2015 Residential (R403.7)
- Texas Health and Safety Code Chapter 388
- Texas Local Government Code Chapter 214 (Sec. 214.212)
- U.S. DOE Building Energy Codes Program, Texas status
- City of Houston, Mechanical Inspections
- Austin Energy, AC and Heat Pump Rebates
- Oncor, 2026 Home Energy Efficiency Program Manual
- ACCA, Manual J Load Calculations vs. Rules of Thumb
- ENERGY STAR, Air-Source Heat Pumps (proper sizing with Manual J)
- EPA, A Brief Guide to Mold, Moisture and Your Home
- Federal Register, DOE test procedures for central ACs and heat pumps (Jan. 5, 2017; appendix M1)
- NOAA CPC, 2025 state cooling degree days
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


