Local Guide · AC and heating
Why Is My Electric Bill So High in Summer? AC Costs and Fixes for Texas and Florida
How to estimate what your AC really costs to run, using real 2026 electricity prices, why bills jump in Texas and Florida, the maintenance and duct problems that quietly raise them, and the free audits, rebates and plan choices that bring them down.
Summer bills spike in Texas and Florida mainly because the AC runs many more hours: in 2024 and 2025 the two states logged the most cooling degree days in the lower 48. Cost depends on system size, efficiency (SEER2), hours of runtime and your price per kWh, which averaged 15.91 cents in Texas and 14.99 cents in Florida in August 2026, per EIA. Dirty filters and coils, leaky attic ducts, a low thermostat setting and, in Texas, a poor retail electricity plan all push bills higher.
Key facts
- Average residential electricity prices in August 2026 were 15.91 cents per kWh in Texas, 14.99 cents in Florida and 18.16 cents nationally (EIA, preliminary).
- Florida logged 3,223 and Texas 3,062 population-weighted cooling degree days in 2024, the two highest in the lower 48; they ranked first and second again in 2025 (NOAA CPC).
- In 2020, 95% of Texas homes and 96% of Florida homes used air conditioning, per EIA's Residential Energy Consumption Survey (EIA).
- ENERGY STAR says almost half of the average household's annual energy bill goes to heating and cooling, more than $900 a year (ENERGY STAR).
- FPL says up to 50% of an energy bill comes from heating and cooling (FPL).
- ENERGY STAR estimates 20% to 30% of the air moving through a typical duct system is lost to leaks and poor connections (ENERGY STAR).
- ENERGY STAR says airflow problems can cut HVAC efficiency by up to 15% (ENERGY STAR).
- New split AC systems under 45,000 Btu/hr installed in Texas or Florida must meet at least 14.3 SEER2 (10 CFR 430.32).
- A Texas city-owned utility decides whether to offer retail electric choice; opting in is irrevocable (Tex. Util. Code §40.051).
Why summer bills are so high in Texas and Florida
The short answer is hours. Your air conditioner is usually the biggest electricity user in a Texas or Florida home, and in summer it runs most of the day. Three facts explain the scale:
- Cooling demand: Cooling degree days measure how much and how long the outdoor temperature stays above 65°F; EIA calculates a day's value as the average of the high and low minus 65. In 2024, Florida logged 3,223 population-weighted cooling degree days and Texas 3,062, the two highest of the lower 48 states, per NOAA's Climate Prediction Center. They ranked first and second again in 2025.
- Nearly everyone has AC: EIA's 2020 survey found 95% of Texas homes and 96% of Florida homes used air conditioning.
- Hot nights: NOAA reports very warm nights (lows of 75°F or more) have been rising in Texas since the 1970s, and Florida's 2020 to 2024 average was about triple the long-term norm. When nights stay hot, the AC never gets a break.
ENERGY STAR says almost half of the average household's annual energy bill goes to heating and cooling. FPL says up to 50% of an energy bill can come from heating and cooling. In a Houston or Tampa July, the AC share can be higher.
What electricity costs in 2026
EIA publishes average residential prices by state each month. The latest figures available when we checked:
| Area | August 2026 (preliminary) | August 2025 |
|---|---|---|
| Texas | 15.91 cents/kWh | 15.40 cents/kWh |
| Florida | 14.99 cents/kWh | 15.33 cents/kWh |
| U.S. average | 18.16 cents/kWh | 17.57 cents/kWh |
Both states are below the national average per kWh, but they use far more cooling, so bills are still high. Your own rate may be very different. Check your bill for the total price per kWh, including delivery charges, base charges and taxes. Divide the total bill by the kWh used to get your all-in rate.
How much does it cost to run an AC per month? The kWh math
You can estimate AC cost with one formula:
kWh per hour = (tons x 12,000) / SEER2 / 1,000
One ton of cooling is 12,000 Btu per hour. SEER2 is the seasonal efficiency rating, in Btu of cooling per watt-hour of electricity, measured under federal test conditions. A higher SEER2 means less electricity for the same cooling.
Worked example: a 3-ton AC
- 3 tons x 12,000 = 36,000 Btu per hour.
- At 14.3 SEER2 (the minimum for a new split AC under 45,000 Btu/hr in Texas and Florida): 36,000 / 14.3 = about 2,520 watts, or about 2.5 kWh per hour of running.
- If it runs 10 hours a day for 30 days: 2.5 x 10 x 30 = about 755 kWh a month.
- At Texas's August 2026 average of 15.91 cents: about $120 for the month. At Florida's 14.99 cents: about $113.
This is an estimate, not a bill prediction. Real efficiency drops on the hottest afternoons, older systems have lower ratings, runtime depends on your house, and your rate includes fees. But it shows how runtime and efficiency drive cost. Double the runtime and you double the cost.
Comparing efficiency levels
| Rating | Watts for a 3-ton system | kWh at 300 hours/month | Cost at 15.91 cents (TX) | Cost at 14.99 cents (FL) |
|---|---|---|---|---|
| 13.4 SEER2 | about 2,690 | about 806 | about $128 | about $121 |
| 14.3 SEER2 | about 2,520 | about 755 | about $120 | about $113 |
| 17 SEER2 | about 2,120 | about 635 | about $101 | about $95 |
| 20 SEER2 | about 1,800 | about 540 | about $86 | about $81 |
Calculated by The Company Chronicle from the formula above and EIA August 2026 average prices. A system rated decades ago under the older SEER scale will typically use more than any row in this table.
How do I calculate SEER2 savings?
Savings percent = 1 - (old SEER2 / new SEER2). Going from 13.4 to 17 SEER2 cuts cooling electricity by about 21% for the same runtime. Multiply your summer cooling kWh by that percentage, then by your rate. If your old system is badly maintained or leaking, real savings can be larger; if your ducts leak, part of the savings disappears into the attic.
Is my AC running constantly normal in 100-degree heat?
Often, yes. Home systems are sized to a local design temperature that is hot but below the extremes. Texas averaged 17.2 days of 100°F or higher per year over 1900 to 2024, and a correctly sized system can run nearly nonstop on those afternoons. Florida rarely hits 100°F, but NOAA says high humidity often pushes the heat index above 105°F, and the AC spends a lot of its effort removing moisture.
Running all afternoon is not by itself a sign of trouble. Warning signs are:
- The AC runs all night too, even when it is in the 70s outside.
- The house never reaches the setpoint, even after sunset.
- Air from vents feels barely cool.
- Your kWh use is much higher than the same month last year at similar temperatures. Many utilities show a weather comparison on the bill or app.
If you see those signs, the problem may be refrigerant, airflow, ducts or a failing part. See our warm air guide.
Problems that quietly raise your bill
| Problem | Why it costs you | Fix |
|---|---|---|
| Dirty filter | Less airflow; ENERGY STAR says airflow problems can cut efficiency up to 15% | Check monthly; replace as needed |
| Dirty outdoor coil | Higher pressures, longer runtime | Rinse with power off; professional cleaning |
| Dirty indoor coil | Less heat transfer, possible freezing | Professional cleaning |
| Leaky attic ducts | ENERGY STAR estimates 20% to 30% of duct airflow is lost in a typical home | Seal with mastic or metal tape; insulate |
| Low refrigerant (leak) | Long runtime for less cooling | Leak search and repair |
| Failing capacitor or motor | Motors draw more power and overheat | Repair |
| Fan set to On | Blower runs all day; in humid homes re-evaporates coil moisture | Set fan to Auto |
| Short cycling (often oversizing) | Frequent startups and poor dehumidification | See our short cycling guide |
| Hot attic and thin insulation | Heat pours through ceilings; ducts gain heat | Air seal and insulate the attic |
| Sun on windows | Direct solar heat gain | Shades, film, exterior shading |
A spring tune-up is the simplest defense. ENERGY STAR recommends a contractor check the cooling system every spring. See our maintenance checklist.
Ducts and attics: the hidden Texas and Florida penalty
Most Texas and Florida homes are built on slabs, so ducts often run through the attic, where summer air can be far hotter than outdoors. Every leak on the supply side dumps cooled air into that attic. Every leak on the return side pulls hot, humid attic air into the system. ENERGY STAR estimates that in a typical house, 20% to 30% of the air moving through ducts is lost to leaks, holes and poor connections.
Florida's code addresses this for new work: duct systems must be pressure-tested, with a prescriptive leakage limit of 4 cfm per 100 square feet of conditioned floor area at 25 pascals, and attic ducts 3 inches or larger must be insulated to at least R-8 (FBC-Energy R403.3.3, R403.3.4, R403.3.1). On Florida change-outs, existing ducts need not be brought to current code if that would require replacing them (R501.7), so older homes may still have leaky ducts. Ask for a duct leakage test when you replace equipment.
Fixes, in rough order of value:
- Seal accessible duct joints and the air handler cabinet with mastic or metal tape. ENERGY STAR says never use duct tape.
- Seal attic air leaks around lights, the attic hatch, plumbing and wiring holes.
- Add attic insulation if yours is thin.
- Consider a radiant barrier in hot attics.
See our duct guide and attic insulation guide.
What temperature should I set my AC to save money?
The warmer the setpoint, the less your AC runs. A frequently cited ENERGY STAR guideline is 78°F when you are home and awake in summer; we could not load the current ENERGY STAR page to confirm it, so treat 78°F as a starting point rather than an official rule. The right number is the warmest setting your household is comfortable and safe with.
Practical tips:
- Raise it in small steps. Try one or two degrees higher for a week before deciding.
- Use ceiling fans when people are in the room. Fans cool people, not rooms, as Trane notes, so turn them off when you leave. The CDC says not to rely on fans when indoor air is above 90°F.
- Control humidity. Drier air feels cooler. Keep the fan on Auto, and keep indoor humidity below 60%, as EPA advises.
- Protect vulnerable people. Older adults, infants and people with heart disease are at higher heat risk, per CDC. Do not push the setpoint up at their expense.
Is it cheaper to leave the AC on all day or turn it up when away?
In most homes, raising the setpoint while you are away saves energy, because a warmer house leaks heat in from outside more slowly, and the AC runs fewer total hours. Turning the system completely off in a Texas or Florida summer is usually a bad idea, though:
- Humidity builds up, which in Florida can mean musty smells and mold. EPA recommends keeping indoor humidity below 60%.
- Recovery from a very hot house can take hours on a hot afternoon, and a correctly sized system recovers slowly.
- Pets, plants, electronics and wood floors suffer in a hot, humid house.
A moderate setback, a few degrees warmer while away, with a schedule that starts cooling an hour or so before you return, balances savings and comfort. Smart thermostats can do this automatically; ENERGY STAR certified models are independently certified, based on field data, to deliver savings. For vacant homes, see our snowbird guide.
Time-of-use pricing and pre-cooling
Some electricity plans charge different prices at different times of day, with the highest prices in late afternoon and early evening when demand peaks. On those plans, pre-cooling can help: cool the house a few degrees more in the cheaper hours before the peak, then let the setpoint drift up during the expensive hours. Your home's walls, furniture and floors act like a small cold battery.
Pre-cooling works best in well-insulated homes with tight ducts. In leaky homes, the stored cooling escapes quickly. It does not save money on a flat-rate plan; there, it may slightly increase total use. Check your plan's rate schedule before trying it.
Utility load control programs are a related option. FPL's On Call program, for example, cycles participating equipment during peak demand, and FPL says customers could save over $90 a year. Many Texas retail providers and city utilities offer smart thermostat demand-response programs; read the terms, including how often and how long they can adjust your thermostat.
Texas: your electricity plan matters as much as your AC
Texas is different from Florida because much of the state has retail electric choice. In those areas, you pick a retail provider and plan, while the local wires company (such as CenterPoint in Houston or Oncor in Dallas-Fort Worth) delivers power and handles outages. The Public Utility Commission of Texas runs an official plan comparison site, PowerToChoose.org.
Not everyone can choose. City-owned utilities decide for themselves whether to offer choice, and Texas law makes that decision the utility's to make (Tex. Util. Code §40.051). Austin Energy and CPS Energy in San Antonio are city-owned and serve their customers directly. Electric cooperatives serve many rural areas.
If you are in a choice area, check your plan:
- Contract end date. When a fixed-rate contract ends, you may roll onto a higher month-to-month rate.
- Price at your usage. Plans advertise a price at specific usage levels, such as 500, 1,000 and 2,000 kWh. Summer AC use often lands at the high end. Compare at your actual summer usage.
- Bill credits and minimum usage fees. Some plans look cheap only within a narrow usage band.
- Time-of-use or free-nights plans. They can help or hurt depending on when your AC runs.
- Electricity Facts Label. Every plan has one. Read it before switching.
Grid alerts: during extreme heat, ERCOT, the grid operator for most of Texas, may ask customers to conserve. Raising the thermostat a few degrees during those hours helps the grid and your bill.
Florida: regulated utilities, but programs differ
In Florida, most homes are served by a regulated utility, such as FPL, Duke Energy Florida, Tampa Electric (TECO) or JEA in Jacksonville. You cannot shop for a different supplier, so the levers are your usage, the rate options your utility offers, and its efficiency programs.
- FPL: instant $200 rebate on a new AC system rated 15.2 SEER2 or higher, installed by an FPL Participating Independent Contractor. FPL's On Call load control program says customers could save over $90 a year.
- Duke Energy Florida: a free Home Energy Check, open to residential customers including renters who have not had one in two years. A June 2025 newspaper report said the expanded program offers up to $1,000 on HVAC replacement and up to $450 for duct testing and repair. Confirm current amounts with Duke.
- Tampa Electric: $40 for a ducted AC or heat pump of at least 15.20 SEER2 and $550 for at least 16.20 SEER2; TECO quadrupled the top rebate from $135 to $550 in June 2025.
- JEA: $200 for ENERGY STAR certified central ACs, heat pumps or mini-splits, plus $50 for an ENERGY STAR smart thermostat.
See our Florida rebate guide.
Free energy audits and rebates in Texas
- Austin Energy: AC and heat pump rebates averaging $800 through participating contractors, with tiered amounts from $600 to $950 depending on efficiency, plus $200 if you join its Home Energy Savings program within six months. The home and old system must be at least 10 years old, and Manual J sizing and city permits are required.
- CPS Energy (San Antonio): central AC and heat pump rebates of $90 to $310 per cooling ton, depending on SEER2 tier and whether the old system still works.
- Oncor (Dallas-Fort Worth and much of north and west Texas): incentives paid to approved service providers, who pass them to customers; the 2026 program accepts applications until December 4, 2026 or until funds run out.
- CenterPoint (Houston): residential HVAC incentives paid to registered project sponsors (contractors), not directly to homeowners.
Ask your utility or retail provider whether it offers a free or discounted home energy assessment. See our Texas rebate guide. Note that the federal 25C tax credit ended for equipment placed in service after December 31, 2025; some utility pages still mention it.
Does a new AC lower my electric bill?
It can, by a lot or a little, depending on what you replace and how it is installed:
- Bigger savings: replacing a very old, low-efficiency or failing system; fixing a refrigerant leak at the same time; sealing ducts; right-sizing an oversized unit.
- Smaller savings: replacing a 10-year-old, well-maintained system with one only slightly more efficient; keeping leaky ducts.
Use the SEER2 formula above with your own kWh history to estimate it. For scale, Trane's 2026 pricing guide estimates installed central AC replacement at $6,568 to $13,669 depending on tier, a manufacturer national estimate. A new system should be replaced because of age, repairs or comfort, with energy savings as a bonus, rather than for savings alone. Our repair or replace guide and SEER2 guide go deeper.
Small businesses: why the bill jumps
Shops, offices and restaurants in Texas and Florida see the same summer effect, often magnified by large windows, doors that open all day, kitchen heat and rooftop units in direct sun. Commercial bills may also include demand charges based on the highest power use in a short interval, so starting several rooftop units at once can raise the bill. Ask your utility or provider how your rate is structured, and stagger startup times if demand charges apply. See our rooftop unit guide and restaurant and retail guide.
How to choose a provider
- Find your all-in price per kWh: total bill divided by kWh used.
- Compare this summer's kWh with last summer's in your utility app.
- Check or replace the air filter monthly during summer.
- Set the fan to Auto.
- Raise the setpoint one or two degrees at a time; use ceiling fans only when people are in the room.
- Rinse the outdoor coil with power off and clear plants away.
- Schedule a spring tune-up.
- Seal and insulate accessible attic ducts with mastic or metal tape.
- Texas choice areas: check your plan's end date and price at your summer usage.
- Ask your utility about free energy checks, rebates and load control programs.
- Do the SEER2 savings math before replacing a working system.
Related ac and heating guides
- What Are SEER2, EER2 and HSPF2? Which Efficiency Rating Matters in Texas and Florida
- Are Your Attic Ducts Leaking? How to Test, Seal or Replace Ductwork in Texas and Florida Heat
- Do Attic Insulation and Radiant Barriers Cut AC Bills in Texas and Florida?
- What Should I Set My Thermostat To, and Can My Utility Change It? A Texas and Florida Thermostat Guide
- Texas AC and Heat Pump Rebates by Utility: Austin Energy, CPS Energy, Oncor, CenterPoint and More
- Florida AC and Heat Pump Rebates: FPL, Duke Energy, TECO, JEA, OUC and More
- AC Maintenance Checklist: What Should You Do Monthly, and What Should a Tune-Up Include in Texas and Florida?
- Should You Repair or Replace Your AC? A Decision Framework With Real Numbers
AC and heating by state and city
Questions people ask
How much does it cost to run AC per month in Texas?
For a 3-ton, 14.3 SEER2 system running 10 hours a day, the estimate is about 755 kWh a month, or about $120 at Texas's August 2026 average of 15.91 cents per kWh (EIA). Your cost depends on your system's size and efficiency, your house, your setpoint and your plan rate. Older or poorly maintained systems and leaky ducts can push the number much higher.
How much does AC cost per month in Florida?
Using the same example, a 3-ton, 14.3 SEER2 system running 10 hours a day uses about 755 kWh a month, about $113 at Florida's August 2026 average of 14.99 cents per kWh (EIA). Florida homes often run the AC for more of the year than Texas homes, so annual costs can be higher even with a lower rate.
How many kWh does a 3-ton AC use?
Divide 36,000 Btu per hour by the SEER2 rating, then by 1,000. A 14.3 SEER2 unit uses roughly 2.5 kWh per hour of running; a 17 SEER2 unit about 2.1 kWh. Real use varies with outdoor temperature and maintenance. Multiply by your runtime hours to get monthly kWh.
Can a failing AC raise my electric bill?
Yes. A refrigerant leak, a dirty coil, a failing capacitor or motor, or a short cycling system can all increase runtime or power draw while delivering less cooling. ENERGY STAR says airflow problems alone can cut efficiency by up to 15%. If your kWh use jumped compared with the same month last year at similar temperatures, have the system checked.
Do ceiling fans actually save money?
Only if you raise the thermostat while using them. Fans move air across your skin, which makes you feel cooler, but they do not cool the room. Turn them off when nobody is in the room. The CDC says fans should not be relied on when indoor temperatures are above 90°F.
What is a utility energy audit and is it free?
It is an inspection of your home's energy use, often including insulation, air leaks, ducts and equipment, with recommendations. Some are free. Duke Energy Florida offers a free Home Energy Check, including for renters, and many utilities offer online or in-person assessments. Ask your Texas utility or retail provider and your Florida utility what is available.
Why does my AC run all the time?
On 100°F Texas afternoons or humid Florida days, a correctly sized system may run almost nonstop, which is normal. If it also runs all night in mild weather, never reaches the setpoint, or blows barely cool air, it may have a refrigerant leak, dirty coils, a failing part, or leaky ducts. Change the filter and schedule a diagnostic visit.
What is time-of-use pricing and should I pre-cool?
Time-of-use plans charge more during peak hours, typically late afternoon and early evening. Pre-cooling means running the AC harder before the peak, then letting the house warm slightly during peak hours. It can save money on those plans in well-insulated homes, but it does not help on flat-rate plans. Check your rate schedule before trying it.
Does turning the AC up when away save money?
Usually yes, because a warmer house gains heat more slowly and the AC runs fewer hours. In Texas and Florida summers, a moderate setback of a few degrees is better than turning the system off, which lets humidity build and can take hours to recover. A programmable or smart thermostat can bring the temperature back down before you get home.
Sources
- U.S. EIA: Electric Power Monthly, Table 5.6.A, Average Price of Electricity to Ultimate Customers by State
- NOAA CPC: 2024 population-weighted state cooling degree days
- NOAA CPC: 2025 population-weighted state cooling degree days
- EIA: Degree days explained
- EIA: 2020 RECS State Air Conditioning data
- ENERGY STAR: Smart Thermostats
- ENERGY STAR: Maintenance Checklist
- ENERGY STAR: Duct Sealing
- 10 CFR 430.32, Energy conservation standards
- Florida Building Code, Energy Conservation 2023, Chapter 4 (R403.3)
- Florida Building Code, Energy Conservation 2023, Chapter 5 (R501.7)
- Texas Utilities Code Chapter 40
- FPL: A/C Rebate
- Tampa Electric: Heating and Cooling rebates
- Tampa Electric news release, June 26, 2025
- JEA: Heating and Cooling Rebates
- Orange Observer: Duke Energy expands rebate program (June 2025)
- Austin Energy: AC rebates
- CPS Energy: HVAC rebates
- Oncor: 2026 Home Energy Efficiency Program Manual
- PUCT filing: CenterPoint Houston energy efficiency plan
- IRS: Energy Efficient Home Improvement Credit (25C)
- NOAA State Climate Summaries 2025: Texas
- NOAA State Climate Summaries 2025: Florida
- CDC: About Heat and Your Health
- EPA: A Brief Guide to Mold, Moisture and Your Home
- Trane: 2026 HVAC Pricing Guide
- Trane: Help! My House Is Hot Upstairs and Cold Downstairs
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


