Local Guide · AC and heating
What Kind of AC Do I Have? Split Systems, Package Units, PTACs and Florida Condo Air Handlers Explained
How to tell a split system from a package unit or a PTAC in two minutes, what each part is called, where your air handler is hiding, how to find your system's age, and what the type means for repairs and replacement in Texas and Florida.
Walk outside. If you see one metal cabinet connected to ducts that run into the house, you have a package unit. If an outdoor condenser connects through two copper lines to an indoor air handler or furnace, you have a split system. A PTAC is a self-contained box through an exterior wall, common in hotels and some Florida condos. The type decides who can work on it, what replacement costs and how it handles humidity.
Key facts
- In the 2020 Residential Energy Consumption Survey, 96% of Florida homes used air conditioning and 90% used central AC; in Texas the figures were 95% and 83%, with 16% using individual units (EIA).
- Single-package air conditioners and heat pumps made since Jan. 1, 2023 must meet at least 13.4 SEER2; single-package heat pumps also need 6.7 HSPF2 (10 CFR 430.32(c)(5)).
- Split-system air conditioners under 45,000 Btu/hr installed in Texas or Florida since Jan. 1, 2023 must meet at least 14.3 SEER2 (10 CFR 430.32(c)(6)).
- Texas's AC licensing law does not apply to work on a portable or self-contained ductless unit of three tons or less, which TDLR says means window units, self-contained through-the-wall units and portables, not mini-splits (Occ. Code Sec. 1302.058; TDLR FAQ).
- Florida requires an auxiliary drain pan or another listed secondary protection method for each cooling coil where condensate overflow could damage the building (FBC-Mechanical 307.2.3).
- Under the Florida energy code, air handlers may be placed in an attic only under the performance path, with conditions including a failed-drain alarm or shutoff (FBC-Energy R403.3.6).
- Trane says properly installed and maintained air conditioners are expected to last about 15 years, and furnaces and heat pumps 15 to 20 years.
- EPA's 2026 rule kept the policy that R-410A replacement condensing units may still be made and sold to repair existing systems.
The two-minute test: which system do you have?
You do not need tools. Walk around the house and look for these clues.
| What you see | What you probably have |
|---|---|
| One outdoor box with a fan on top, plus copper lines into the house, and a second cabinet inside (garage, closet, attic) | Split system |
| One large outdoor cabinet on a slab or the roof, with big insulated ducts running from it into the wall, crawlspace or attic | Package unit |
| A box under a window or through the wall with a grille inside and outside, often with its own control panel | PTAC or through-the-wall unit |
| A box hanging in a window | Window unit |
| Small white heads high on interior walls, connected to an outdoor unit | Ductless mini-split |
| A tall closet in a Florida condo with louvered doors and a unit humming inside | Split system with a closet air handler |
Also check the thermostat wiring and the data plates. The outdoor nameplate lists the model number. Many brands use a model number that tells you whether the unit is an AC, a heat pump, or a package unit. You can look up the full rating for your matched equipment in the AHRI directory using the model numbers.
What is a split system?
A split system divides the work between two cabinets. Outside, the condenser (or heat pump outdoor unit) holds the compressor, the outdoor coil and a large fan. Inside, an air handler or a furnace with an evaporator coil moves air through your ducts. Two copper refrigerant lines, called the line set, connect them.
Split systems are the most common setup in Texas and Florida homes built in the last few decades. In Houston, Dallas and San Antonio the indoor unit is often a gas furnace in the attic or garage with a coil on top. In Florida it is usually an electric air handler with heat strips, in a closet, garage or attic.
Pros
- Many efficiency levels available, including variable-speed systems.
- Indoor and outdoor parts can sometimes be repaired or replaced separately.
- The indoor unit is protected from weather and salt air.
Cons
- Two locations to maintain, and the line set can leak.
- Indoor units in attics can overflow and damage ceilings if the drain clogs.
- Replacing only the outdoor unit can create a mismatch with the indoor coil, which hurts efficiency and can affect rebates and warranty.
What is a package unit?
A package unit puts everything in one outdoor cabinet: compressor, both coils, the blower and sometimes a gas burner. Supply and return ducts connect directly to the cabinet. There are several types:
- Package air conditioner with electric heat strips.
- Package heat pump, which heats and cools.
- Gas-electric ("gas pack"): electric cooling with a gas furnace section in the same box.
- Dual fuel package: a heat pump with gas backup.
You will see package units on manufactured homes, on older ranch homes with crawlspaces, on homes with no attic or closet space, and on the roofs of small commercial buildings. Texas law has a specific rule for manufactured homes: a licensed manufactured-home installer may do AC work only if the on-site installation of AC components is done by a TDLR-licensed AC contractor (Occ. Code Sec. 1302.061).
Pros
- Frees indoor space; no air handler closet.
- No indoor condensate pan above a ceiling.
- One cabinet to service.
Cons
- The whole system sits outside in sun, rain, salt and floodwater.
- Ducts often pass through the wall or crawlspace, where leaks bring in humid air.
- Federal minimum efficiency is a bit lower (13.4 SEER2) than for split ACs installed in the South (14.3 SEER2 under 45,000 Btu/hr), so cheaper package units can cost more to run.
- A failure usually means replacing the whole cabinet.
For commercial rooftop package units, see our rooftop unit guide.
Split system vs package unit: side by side
| Feature | Split system | Package unit |
|---|---|---|
| Equipment location | Outdoor condenser plus indoor air handler or furnace | One outdoor cabinet |
| Federal minimum (made 2023+) | AC: 14.3 SEER2 under 45k Btu/hr, 13.8 SEER2 at 45k+ installed in TX/FL; heat pump 14.3 SEER2 / 7.5 HSPF2 | 13.4 SEER2; package heat pump 6.7 HSPF2 |
| Indoor space needed | Closet, attic or garage | None |
| Water damage risk indoors | Higher (indoor drain pan) | Lower |
| Exposure to weather and salt | Outdoor half only | Entire system |
| Hurricane and flood risk | Outdoor unit can be raised | Whole system at ground level unless on a stand or roof |
| Replacement | Usually both halves together | One cabinet, sometimes with new curb or duct transitions |
Neither type is better for every home. The best choice is usually the type the house was designed for, unless you are also fixing ducts or freeing up space.
What is a PTAC or through-the-wall unit?
A PTAC (packaged terminal air conditioner) is a self-contained unit that sits in a metal sleeve through an exterior wall. It cools one room, and most have electric heat strips. A PTHP is the heat pump version. You see them in hotels, assisted living buildings, older apartment buildings and hotel-style condos along the Florida coast.
A through-the-wall AC looks similar but is usually a residential product, rated more like a window unit. Both slide into a sleeve, plug into a dedicated outlet and drain outside.
Why it matters who can work on it
In Texas, Occupations Code Sec. 1302.058 exempts work on "a portable or self-contained ductless air conditioning product that has a cooling capacity of three tons or less." TDLR's FAQ says this exemption refers to window units, self-contained through-the-wall units such as hotel units, and portables. So a building maintenance person can often swap a PTAC. A mini-split, which is not self-contained, still needs a licensed contractor. In Florida, check with the condo association and local building department; replacing a sleeve or changing the opening in an exterior wall may need approval.
PTAC pros and cons
- Each room controls its own temperature, and one failure affects only one room.
- Easy swap if the new unit fits the existing sleeve.
- Noisier and less efficient than a mini-split or central system.
- Humidity control can be weak, especially when an oversized unit short-cycles, which matters in a closed-up Florida condo.
- Self-contained units made or imported from January 1, 2025 must use a refrigerant with a GWP of 700 or less under EPA's Technology Transitions rule, so replacements may use a different refrigerant than the old unit.
Why does my Florida condo have an AC closet?
Many Florida condos and townhomes have a split system with the air handler in a small closet, often in the hall, with a return grille in the closet door or wall. The condenser sits on the roof, a balcony, a mechanical room, or a ground pad. The closet design keeps the air handler inside the building, where it is easier to service and not exposed to a hot attic.
What owners should know:
- The drain matters most. In a high-rise, a clogged drain can leak into the unit below. Florida's mechanical code requires an auxiliary drain pan or another listed secondary protection method, such as a float switch that shuts the unit off, wherever condensate overflow could damage the building.
- Keep the closet clear. Storage blocks airflow and can pull dust into the return.
- Filters are often in the closet door grille or slid into the air handler itself. See our filter guide.
- The association may own part of the system. Your declaration decides whether the condenser on the roof is yours, and who must replace it. See HOA and condo AC rules.
Where is my air handler?
Common spots in Texas and Florida homes:
- Attic: very common in Texas, especially with gas furnaces. Look for a pull-down ladder and a large metal cabinet with ducts attached. Florida's current energy code allows attic air handlers only under the performance compliance path, with a required alarm or shutoff for a failed condensate drain and a notice on the electrical panel.
- Garage: common in Florida and in Texas slab homes. Often on a platform.
- Hall or utility closet: common in Florida homes and condos.
- Crawlspace or under the house: sometimes in older pier-and-beam homes.
- Nowhere inside: if you cannot find one, you probably have a package unit outside.
Tip: follow the large return grille in your hallway. The air handler is usually close to it.
Parts glossary: evaporator, condenser and the rest
| Part | Where | What it does |
|---|---|---|
| Condenser (outdoor unit) | Outside | Releases indoor heat to outdoor air; holds the compressor |
| Compressor | Inside the condenser | Pumps refrigerant; the most expensive part |
| Condenser coil | Outdoor unit sides | Fins that shed heat; must be kept clean |
| Evaporator coil (A-coil) | On or in the air handler or furnace | Gets cold, absorbs heat and pulls moisture from indoor air |
| Air handler | Closet, attic, garage | Cabinet with the blower, coil and often heat strips |
| Blower | In the air handler or furnace | Moves air through the ducts |
| Heat strips | In the air handler | Electric resistance heat; backup or main heat in many Florida homes |
| Line set | Between units | Two copper refrigerant lines, one insulated |
| Expansion device (TXV or piston) | At the indoor coil | Meters refrigerant into the coil |
| Capacitor | Outdoor unit | Helps motors start; a common, cheap failure |
| Contactor | Outdoor unit | Switch that turns the outdoor unit on and off |
| Condensate drain and pan | Under the coil | Carries away water removed from the air |
| Float switch | On the pan or drain | Shuts the system off if water backs up |
| Return and supply ducts | Attic, walls, crawlspace | Return brings air back; supply delivers cooled air |
| Plenum | At the air handler | The box where ducts connect to the unit |
For more terms, see the HVAC glossary.
How do I find the age of my AC from the serial number?
Most manufacturers code the build year, and often the week or month, into the serial number on the data plate. The trouble is that each brand uses its own format and many have changed formats over the years. We could not confirm a current, brand-by-brand decoding table from manufacturer sources, so we do not publish one here. Third-party decoders exist, but they can be wrong for older or rebranded equipment.
Reliable ways to find the age:
- Read the whole data plate. Many plates print a manufacture date ("MFG DATE" or a month and year) separately from the serial number.
- Call the manufacturer's customer service with the model and serial number. They can tell you the build date and whether warranty registration exists.
- Look up the permit. Houston, Dallas, Miami-Dade and most other jurisdictions keep permit records searchable by address. A replacement permit date is usually within weeks of installation.
- Check closing documents. A home inspection report often lists the system age.
- Look for stickers from past service visits inside the air handler door.
Check both halves of a split system. The condenser may have been replaced years after the air handler, or the reverse. Age matters for repair-or-replace decisions and warranties: see AC lifespan and repair or replace.
How long do these systems last?
Trane says a properly installed and maintained air conditioner should last about 15 years, and furnaces and heat pumps 15 to 20 years. In practice, coastal salt air, constant run time, and poor drainage shorten life in Florida and on the Texas coast. Package units sit fully outdoors, so their cabinets, coils and controls face more weather than a split system's indoor half. PTACs and window units are built as lower-cost products, and owners commonly replace them rather than repair major parts.
Signs your system is near the end: repeated refrigerant leaks, a failed compressor out of warranty, rusted coil fins that crumble, or an older R-22 system. For repairs on existing R-410A systems, EPA's 2026 rule says replacement R-410A condensing units can still be made and sold for repair, but R-410A refrigerant prices are expected to rise. See the refrigerant transition guide and coastal corrosion.
What the system type means for replacement
- Split to split: the most common change-out. Replace both halves together so the coil matches the condenser; utility rebates usually require it. FPL requires full replacement of condenser, blower and evaporator coil. Austin Energy requires all components replaced.
- Package to package: usually simpler, but new units may have a different footprint, so duct transitions or a new pad may be needed.
- Package to split: possible if you have space for an air handler. It can improve efficiency options and protect the indoor half from weather.
- PTAC to PTAC: buy a unit that fits the existing sleeve and electrical outlet. Measure the sleeve first.
- Air handler only: Trane's 2026 guide estimates installed air handler replacement at $5,172 to $8,742 depending on tier. That is a manufacturer national estimate for its own equipment, not an independent study.
In Florida, replacement equipment installed under a permit must meet current minimum efficiency (FBC-Energy R501.7), and replacing a condenser counts as a replacement, not a repair. In Houston, replacing a condenser, evaporator or furnace needs a mechanical permit. See our replacement cost guide.
How to choose a provider
- Walk outside and count cabinets: one large box with ducts means package; condenser plus copper lines means split.
- Find the indoor unit: attic, garage, closet or crawlspace.
- Photograph every data plate (model, serial, refrigerant type, electrical ratings).
- Find the system's age from the data plate, the manufacturer or your city's permit records.
- Locate the filter slot and the condensate drain.
- Check whether a float switch or secondary drain pan is installed under an indoor coil.
- For condos, read the declaration to see who owns and replaces each part.
- Look up your matched equipment ratings in the AHRI directory before comparing replacement quotes.
Related ac and heating guides
- Are Ductless Mini-Splits Worth It for Garages, Additions and Whole Homes in Texas and Florida?
- How Long Do AC Units Last in Texas and Florida?
- HOA and Condo Rules for AC: Replacement Approvals, Rooftop Units, Condensers and Who Pays
- New Homeowner's Guide: How Does My AC and Heating System Work, and What Do I Do First?
- What Do HVAC Terms Mean? A Plain-English Glossary From A2L to Zoning
- How Much Does a New AC or Heat Pump Cost in 2026? What a Fair Texas or Florida Quote Includes
- Commercial Rooftop Units (RTUs): Repair, Replacement and Maintenance for Small Businesses
- Why Is Water Leaking From My AC Inside the House?
AC and heating by state and city
Questions people ask
What is the difference between a split system and a package unit?
A split system has an outdoor condenser and an indoor air handler or furnace connected by refrigerant lines. A package unit holds everything in one outdoor cabinet connected to the house by ducts. Split systems keep half the equipment indoors and offer more efficiency options; package units save indoor space but put the whole system in the weather.
Is a package unit less efficient than a split system?
Not always, but the federal minimum is lower. Package ACs made since 2023 must reach 13.4 SEER2, while split ACs under 45,000 Btu/hr installed in Texas or Florida must reach 14.3 SEER2. Higher-efficiency package units exist. Compare the SEER2 on the specific models you are quoted.
What is a PTAC?
A packaged terminal air conditioner is a self-contained unit installed through an exterior wall in a metal sleeve. It cools and usually heats a single room. PTACs are common in hotels, senior housing and hotel-style condos. A PTHP is the heat pump version. In Texas, work on self-contained units of three tons or less is exempt from AC contractor licensing.
Can a handyman replace my PTAC or through-the-wall unit in Texas?
Often yes. Texas Occupations Code Sec. 1302.058 exempts work on self-contained ductless units of three tons or less, and TDLR's FAQ names through-the-wall units like hotel units as examples. The exemption does not cover mini-splits or central systems. Electrical work and any change to the wall opening may still need permits or a licensed electrician.
Where is the filter on a package unit?
Usually in a return grille inside the house, often in a hallway ceiling or wall. Some package units have a filter rack in the outdoor cabinet behind an access panel. If you cannot find a filter at any return grille, ask a technician to show you, and do not run the system without one.
How do I know if I have a heat pump or an AC?
Check the outdoor unit's model number and data plate; many list "heat pump" or a heating rating. A thermostat with an "Aux" or "Em Heat" setting suggests a heat pump. In winter, a heat pump's outdoor unit runs while heating, and you may see it go through defrost cycles with some steam.
Should I replace a package unit with a split system?
Consider it if you have a good indoor location for an air handler, want higher efficiency options, or live where the package unit is exposed to salt or flooding. It costs more because of new line sets, an indoor unit and duct changes. If the existing ducts are tied to the package location, staying with a package unit is usually cheaper.
Why does my condo AC leak into the unit below?
Usually a clogged condensate drain or a missing or failed overflow safety device. Florida's mechanical code requires an auxiliary drain pan or another listed secondary protection method where overflow could damage the building. Have the drain cleared, confirm a float switch works, and check your condo documents for who pays for damage.
Sources
- EIA, Air conditioning in U.S. homes by state, 2020 RECS
- 10 CFR 430.32, Energy conservation standards
- Texas Occupations Code Chapter 1302
- TDLR, Air Conditioning and Refrigeration FAQ
- Florida Building Code-Mechanical 2023, Chapter 3
- Florida Building Code-Energy Conservation 2023, Chapter 4 (Residential)
- Florida Building Code-Energy Conservation 2023, Chapter 5 (Existing Buildings)
- Trane, HVAC Replacement Cost Guide (2026)
- EPA, Technology Transitions HFC Restrictions by Sector
- Federal Register, Technology Transitions reconsideration final rule (May 26, 2026)
- Houston Permitting Center, Mechanical Inspections
- FPL, Residential HVAC Program Standards
- Austin Energy, AC and Heat Pump Rebates
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


