Local Guide · AC and heating
What Do HVAC Terms Mean? A Plain-English Glossary From A2L to Zoning
Plain-English definitions of the words on your AC quote, invoice and nameplate, with current 2026 rules for Texas and Florida and links to the guide that covers each one.
HVAC stands for heating, ventilation and air conditioning. The key terms: the condenser is the outdoor unit that releases heat; the evaporator coil is the indoor coil that absorbs heat and moisture; a ton is 12,000 Btu per hour of cooling; SEER2 measures cooling efficiency (Texas and Florida split ACs under 45,000 Btu/hr need at least 14.3); and new systems use A2L refrigerants such as R-454B or R-32. This glossary defines more than 130 terms.
Key facts
- One ton of cooling equals 12,000 Btu per hour.
- Split ACs under 45,000 Btu/hr installed in Texas or Florida must meet at least 14.3 SEER2 (10 CFR 430.32).
- Split heat pumps nationally must meet 14.3 SEER2 and 7.5 HSPF2.
- New home AC and heat pump systems must use refrigerant with GWP of 700 or less from Jan. 1, 2025; R-454B is GWP 470 and R-32 is GWP 675.
- R-410A has a GWP of 2,090 and is classed A1 (nonflammable).
- U.S. production and import of R-22 ended Jan. 1, 2020.
- ENERGY STAR says 20% to 30% of air moving through a typical duct system is lost to leaks.
- Florida's residential code (M1411.8) requires locking caps on outdoor refrigerant access ports.
How to use this glossary
This glossary defines the terms you will see on quotes, invoices, nameplates and in our guides to air conditioning and heating in Texas and Florida. Each term is defined in plain English, and many link to the guide that covers it in depth. Federal and state numbers (efficiency minimums, license limits, refrigerant rules) are current as of November 2026 and are sourced at the bottom of this page. Start with the AC and heating hub for the big picture, or the new homeowner HVAC basics guide if you just bought a house.
HVAC terms starting with A
- A1 refrigerant: An ASHRAE Standard 34 safety class for refrigerants with low toxicity and no flame spread. R-22 and R-410A are A1.
- A2L refrigerant: A safety class for refrigerants with low toxicity and low flammability (mildly flammable). R-454B and R-32 are A2L and are now standard in new home systems. See the refrigerant transition.
- ACCA: Air Conditioning Contractors of America, the trade group that publishes Manual J (load calculation), Manual S (equipment selection) and Manual D (duct design).
- AFUE: Annual Fuel Utilization Efficiency: the share of fuel a furnace turns into usable heat over a season. Non-weatherized gas furnaces made from Nov. 19, 2015 must be at least 80% AFUE under federal rules.
- AHRI: The Air-Conditioning, Heating, and Refrigeration Institute. Its directory certifies the ratings of matched indoor and outdoor combinations. Many rebates require an AHRI certificate.
- AHRI certificate: A document listing the certified SEER2, EER2 and HSPF2 for one exact combination of outdoor unit, indoor coil or air handler, and furnace. Ask for it with every quote. See comparing quotes.
- AIM Act: The American Innovation and Manufacturing Act of 2020, which lets EPA phase down HFC refrigerants. U.S. HFC production and consumption fall to 30% of baseline in 2029.
- Air handler: The indoor unit containing the blower and usually the evaporator coil and heat strips. In Texas and Florida it often sits in a closet, garage or attic.
- Airflow (CFM): The volume of air the blower moves, in cubic feet per minute. Too little airflow can freeze the coil and reduce efficiency; ENERGY STAR says airflow problems can cut efficiency by up to 15%.
- Auxiliary heat (aux heat): Backup heat, usually electric strips, that helps a heat pump on cold mornings and during defrost. See heat pump buying guide.
- Attic air handler: An air handler installed in the attic, common in Texas and Florida. Florida requires an alarm or shutoff for a failed condensate drain when one is installed under the performance path.
HVAC terms starting with B
- Blower motor: The fan motor in the air handler or furnace that pushes air through the ducts. ECM (variable-speed) motors use less power than older PSC motors.
- BTU: British thermal unit: the heat needed to raise one pound of water by 1°F. Cooling capacity is rated in BTU per hour (Btu/hr).
- Btu/hr: Capacity per hour. 12,000 Btu/hr equals one ton of cooling.
- Bypass: A duct or damper that sends some supply air back to the return, sometimes used with zoning. Often a sign of a design compromise.
HVAC terms starting with C
- Capacitor: A component that stores electric charge to start and run the compressor and fan motors. A failed capacitor is one of the most common summer AC repairs. See AC not working checklist.
- Carbon monoxide (CO): A colorless, odorless gas from incomplete combustion. Gas furnaces are a household source. CPSC advises CO alarms on every level and outside sleeping areas. See CO safety.
- Charge: The amount of refrigerant in a system, set by the manufacturer for the equipment and line set length.
- Class A / Class B license (Texas): Texas ACR contractor license classes. Class B covers systems up to 25 tons cooling or 1.5 million Btu/hr heating; Class A has no size limit. See Texas HVAC licensing.
- Class A / B / C license (Florida): Florida air-conditioning contractor classes. Class B covers up to 25 tons cooling and 500,000 Btu heating; Class C is service-only and no longer issued to new applicants. See Florida HVAC licensing.
- Coil: A network of copper or aluminum tubes and fins where refrigerant absorbs or releases heat. Every system has an indoor (evaporator) coil and an outdoor (condenser) coil.
- Commissioning: Checking a new system after installation: refrigerant charge, airflow, static pressure, temperature split, drain and controls. See installation day.
- Compressor: The pump in the outdoor unit that pressurizes refrigerant and drives the cooling cycle. It is the most expensive part to replace.
- Condensate: Water removed from the air by the cold indoor coil. It drains through a pipe outside or to a drain.
- Condensate drain line: The pipe carrying condensate away. A clog causes water leaks and float-switch shutoffs. See AC leaking water.
- Condensate pump: A small pump that lifts condensate when gravity drainage is not possible.
- Condenser: The outdoor unit of a split AC or heat pump, containing the compressor, condenser coil and fan. It releases the heat taken from your home.
- Contactor: An electrical switch in the outdoor unit that turns the compressor and fan on when the thermostat calls for cooling. Pitted or stuck contactors are a common repair.
- Cooling degree day (CDD): A measure of cooling need: a day's mean temperature minus 65°F. Florida (3,041) and Texas (3,009) led the lower 48 in 2025.
- Cycle: One on-off run of the system. See short cycling.
HVAC terms starting with D
- Damper: A plate inside ductwork that opens or closes to control airflow, manually or with a zoning motor.
- Defrost cycle: A heat pump function that briefly reverses to melt frost from the outdoor coil in heating season. Steam from the outdoor unit is normal.
- Dehumidifier: A device that removes moisture from air. Whole-house units connect to ductwork; portable units sit in a room. See humidity and mold.
- Delta T (temperature split): The difference between return and supply air temperatures. Technicians use it as one check of cooling performance.
- Design temperature: The outdoor temperature used in a load calculation, set for each location, that the system is sized to handle.
- Disconnect: The outdoor electrical switch box near the condenser that cuts power for service.
- Drain pan: The tray under the indoor coil that catches condensate. A secondary or auxiliary pan sits underneath as backup; Florida requires overflow protection where overflow could cause damage.
- Dual fuel: A heat pump paired with a gas furnace; the system picks the cheaper or more effective heat source by outdoor temperature.
- Duct leakage: Air escaping from or into ducts. ENERGY STAR estimates 20% to 30% of air in typical duct systems is lost to leaks. See duct leaks.
- Ductless mini-split: A system with an outdoor unit feeding one or more wall, ceiling or floor indoor heads, with no ducts. See mini-split guide.
HVAC terms starting with E
- ECM motor: Electronically commutated motor: an efficient variable-speed motor used in blowers and condenser fans.
- EER2: Energy Efficiency Ratio 2: cooling efficiency at one hot test condition. Useful for comparing performance on very hot afternoons.
- Emergency heat: A thermostat setting that runs only the backup heat (strips or furnace) and locks out the heat pump. Use it only if the heat pump fails.
- ENERGY STAR: The EPA-run label for efficient products. Split heat pumps must reach at least 15.2 SEER2, 11.0 EER2 and 7.8 HSPF2.
- EPA Section 608: The federal certification required to service or dispose of equipment containing refrigerant, and to buy refrigerant for stationary systems. See EPA 608.
- Evaporator coil: The indoor coil where liquid refrigerant evaporates and absorbs heat and moisture from your home's air.
- Expansion device: The part that drops refrigerant pressure before the evaporator: a fixed orifice (piston), TXV or electronic expansion valve.
HVAC terms starting with F
- Fan coil: Another name for an air handler with a coil, common in Florida condos.
- Filter (MERV): The air filter at the return or air handler. MERV (Minimum Efficiency Reporting Value) rates how well it captures particles. See air filters and MERV.
- Flame sensor: A rod in a gas furnace that confirms the burner is lit. A dirty sensor makes the furnace shut off soon after lighting.
- Float switch: A safety switch in the drain pan or line that shuts the AC off when water backs up, preventing overflow.
- Flux / brazing: Joining copper refrigerant lines with high-temperature filler metal. Nitrogen should flow through lines while brazing to prevent internal scale.
- Freon: A brand name often used loosely for any refrigerant, especially R-22.
- Furnace: A heating appliance that burns gas or uses electric resistance and blows heated air through ducts.
HVAC terms starting with G
- GWP: Global warming potential: how much a refrigerant warms the climate compared with carbon dioxide. New home AC systems must use refrigerant with GWP of 700 or less.
- Grille / register: The covers over supply and return openings. Registers usually have adjustable louvers; grilles do not.
HVAC terms starting with H
- HCFC-22: The chemical name for R-22. U.S. production and import ended Jan. 1, 2020.
- Heat exchanger: The metal chamber in a furnace that separates combustion gases from house air. A cracked heat exchanger can leak carbon monoxide.
- Heat index: How hot it feels when humidity is combined with temperature. At 96°F and 65% humidity, NWS puts the heat index at 121°F.
- Heat pump: An AC that can reverse to heat, using a reversing valve. See heat pump buying guide.
- Heat strips (electric heat): Electric resistance coils in an air handler. They make about one unit of heat per unit of electricity, which is less efficient than a heat pump.
- Heating degree day (HDD): A measure of heating need: 65°F minus a day's mean temperature.
- HFC: Hydrofluorocarbon refrigerants such as R-410A, being phased down under the AIM Act.
- HFO: Hydrofluoroolefin: a family of very low-GWP refrigerant chemicals, used on their own or blended with HFCs to make lower-GWP refrigerants.
- Home warranty: A service contract covering repair of home systems, separate from the manufacturer warranty. See home warranty coverage.
- HSPF2: Heating Seasonal Performance Factor 2: seasonal heating efficiency of a heat pump. Federal minimum for split heat pumps is 7.5. See SEER2 and HSPF2.
- Humidistat: A control that runs equipment based on relative humidity rather than temperature.
- HVAC: Heating, ventilation and air conditioning.
HVAC terms starting with I
- Inducer motor: A small fan in a gas furnace that pulls combustion gases through the heat exchanger and out the flue.
- Inverter: Electronics that vary compressor speed in variable-speed systems and mini-splits.
- IAQ: Indoor air quality: filtration, ventilation, humidity and pollutant control.
HVAC terms starting with L
- Latent load: The moisture-removal part of the cooling load. Florida's energy code requires equipment latent capacity to meet the calculated latent load.
- Line set: The pair of copper tubes connecting the outdoor and indoor units: a larger insulated suction line and a smaller liquid line.
- Load calculation: A room-by-room estimate of heat gain and loss, usually ACCA Manual J, used to size equipment.
- Locking refrigerant caps: Tamper-resistant caps on outdoor service ports. Required on outdoor ports by Florida's residential code (M1411.8). See copper theft.
- Low-voltage wiring: The thin thermostat wires (usually 24 volts) that tell the system when to run.
HVAC terms starting with M
- Manual J: ACCA's residential load calculation method. Florida requires it (or an approved method) for sizing. See Manual J sizing.
- Manual S: ACCA's method for selecting equipment that matches the Manual J loads.
- Manual D: ACCA's duct design method.
- Matched system: An outdoor unit and indoor coil or air handler certified together by AHRI. Florida requires matched units on replacements.
- MERV: See Filter. Higher MERV catches smaller particles but can restrict airflow if the system is not designed for it.
- Mechanical permit: The building permit required for most HVAC installs and replacements. See permits.
- Mold: Fungal growth that thrives on damp materials. EPA recommends indoor humidity below 60%.
HVAC terms starting with N
- NATE: North American Technician Excellence, a voluntary technician certification. It is not a state license.
- Nameplate: The data label on equipment showing model, serial number, refrigerant type and electrical ratings.
- Notice of Commencement: A Florida document recorded before many improvements. HVAC repair or replacement contracts under $15,000 are exempt from the permit-related requirement.
HVAC terms starting with O
- Ozone depletion potential (ODP): A measure of harm to the ozone layer. R-22 has ODP; R-410A, R-454B and R-32 do not.
- Orifice (piston): A fixed metering device that controls refrigerant flow into the evaporator.
HVAC terms starting with P
- Package unit: A system with all components in one outdoor cabinet, on a slab or roof. See package vs split.
- Plenum: The box-shaped chamber attached to the air handler or furnace that connects to supply or return ducts.
- Pressure switch: A safety switch that shuts down equipment if refrigerant or venting pressures are outside safe limits.
- PTAC: Packaged terminal air conditioner: the through-wall units in hotels and some apartments.
- Puron: A Carrier trade name for R-410A. Brand names for refrigerants vary; the nameplate lists the actual R-number.
HVAC terms starting with R
- R-22: An older ozone-depleting refrigerant. Existing systems may keep running and be serviced with recovered or reclaimed R-22. See refrigerant leaks.
- R-22a: A flammable hydrocarbon blend falsely sold as an R-22 replacement. EPA says it is not an acceptable substitute in home AC.
- R-32: A single-component A2L refrigerant with GWP 675, used in some new systems.
- R-410A: The A1 refrigerant used in most home systems from about 2010 until 2025, GWP 2,090. Restricted for new systems, but pre-2025 equipment may still be installed under EPA's May 2026 rule.
- R-454B: An A2L refrigerant blend with GWP 470, used in many new systems.
- Radiant barrier: A reflective attic material that reduces heat radiated from the roof. See attic insulation and radiant barrier.
- Refrigerant: The fluid that carries heat through the system as it changes between liquid and gas.
- Relative humidity (RH): The amount of moisture in air compared with the most it can hold at that temperature.
- Return: Ducts and grilles that bring room air back to the air handler.
- Reversing valve: The four-way valve that lets a heat pump switch between heating and cooling.
- RTU: Rooftop unit: a commercial package unit. See rooftop units.
HVAC terms starting with S
- Schrader valve: The service port valve where technicians attach gauges.
- SEER2: Seasonal Energy Efficiency Ratio 2: seasonal cooling efficiency, used for equipment made from 2023. Split ACs under 45,000 Btu/hr in Texas and Florida need at least 14.3 SEER2.
- Sensible load: The temperature part of the cooling load, as opposed to moisture (latent).
- Serial number: The code on the nameplate that often reveals the manufacture date. See AC lifespan and age.
- Short cycling: Turning on and off too often. Causes include oversizing, low refrigerant and thermostat placement. See short cycling.
- Single-stage: A compressor with one speed: full on or off.
- Split system: A system with an outdoor condenser or heat pump and an indoor air handler or furnace coil, joined by a line set.
- Static pressure: The resistance to airflow in ducts and filters, measured in inches of water column. High static pressure means restricted ducts or filters and strains the blower.
- Subcooling: How far liquid refrigerant is cooled below its condensing temperature. Technicians use it to check charge on systems with a TXV.
- Superheat: How far refrigerant vapor is heated above its boiling temperature. Technicians use it to check charge, especially on fixed-orifice systems.
- Supply: Ducts and registers that deliver conditioned air to rooms.
- Surge protector: A device at the outdoor unit or panel that limits voltage spikes. Trane suggests an HVAC-rated surge protector in storm-prone areas.
HVAC terms starting with T
- TDLR: Texas Department of Licensing and Regulation, which licenses ACR contractors and technicians.
- DBPR / CILB: Florida's Department of Business and Professional Regulation and its Construction Industry Licensing Board, which license AC and mechanical contractors.
- Thermostat: The control that tells the system when to run. See thermostats.
- Ton: A unit of cooling capacity equal to 12,000 Btu/hr. A 3-ton system is 36,000 Btu/hr.
- TXV: Thermostatic expansion valve: a metering device that adjusts refrigerant flow to the evaporator based on load.
- Two-stage: A compressor with low and high capacity settings. Low stage runs most of the time, often improving humidity control.
HVAC terms starting with U
- UV light: Ultraviolet lamps sometimes installed near the coil to limit microbial growth.
- Unitary system: Industry term for central ducted ACs and heat pumps, split or packaged.
HVAC terms starting with V
- Variable-speed: A compressor or blower that runs across a range of speeds to match the load.
- Venting (refrigerant): Releasing refrigerant to the air. Knowingly venting during service or disposal is illegal under federal rules.
- VRF: Variable refrigerant flow: commercial ductless systems with many indoor units. New VRF systems must meet a 700 GWP limit from Jan. 1, 2027.
HVAC terms starting with W
- Warranty registration: Signing up new equipment with the manufacturer, often within a set number of days, to get the longest parts warranty. See warranty registration.
- Weatherized furnace: A furnace built for outdoor installation, as in a gas package unit. Federal minimum is 81% AFUE.
- Wet bulb: A temperature reading that reflects humidity, used by technicians to check charge and performance.
HVAC terms starting with Z
- Zoning: Splitting a home into areas controlled by separate thermostats and motorized dampers. Helpful in two-story Texas homes. See upstairs too hot.
Terms that confuse people most
Condenser vs evaporator
The condenser is outside and gets rid of heat. The evaporator is inside and absorbs heat and moisture. Both are coils. When a technician says "your coil is leaking," ask which one: indoor coil replacement and outdoor unit replacement are very different jobs.
Tonnage vs efficiency
Tons measure how much cooling a system can deliver. SEER2 measures how efficiently it does it. A bigger ton rating is not "better." An oversized system short cycles and leaves humidity high, which is why Florida's energy code caps cooling capacity at 1.15 times the calculated load.
Capacitor vs contactor
Both live in the outdoor unit and both are common, relatively inexpensive repairs. The capacitor helps start motors; the contactor is the switch that turns the unit on. If the outdoor fan hums but does not spin, the capacitor is a usual suspect. If the outdoor unit never turns on while the indoor blower runs, the contactor or low-voltage wiring may be the issue. See AC will not turn on.
Superheat and subcooling
These are measurements, not parts. A technician measures pressures and line temperatures, then calculates superheat or subcooling to decide whether the refrigerant charge is right. "Topping off" refrigerant without these checks, or without finding a leak, is a red flag. See HVAC scam red flags.
Emergency heat vs aux heat
Aux heat turns on automatically to help a heat pump. Emergency heat is a setting you choose that turns the heat pump off and runs only the backup. Running emergency heat by mistake can raise your winter bill sharply.
Manufacturer warranty vs home warranty
A manufacturer warranty covers defective parts, usually not labor, and often requires registration. A home warranty is a separate service contract you buy, with its own limits and exclusions. See warranty registration and home warranty coverage.
Related ac and heating guides
- New Homeowner's Guide: How Does My AC and Heating System Work, and What Do I Do First?
- What Are SEER2, EER2 and HSPF2? Which Efficiency Rating Matters in Texas and Florida
- R-22, R-410A, R-454B and R-32: What Does the Refrigerant Transition Mean for You in 2026?
- What Size AC Do I Need? Manual J, Tonnage Myths and the Rule-of-Thumb Trap
- What Kind of AC Do I Have? Split Systems, Package Units, PTACs and Florida Condo Air Handlers Explained
- Is a Heat Pump Worth It in Texas and Florida? A Hot-Humid Climate Buying Guide
AC and heating by state and city
Questions people ask
What is a condenser?
The condenser is the outdoor unit of a split AC or heat pump. It holds the compressor, the outdoor coil and a fan. Refrigerant carrying heat from your home is compressed and pumped through the condenser coil, where the fan blows outdoor air across it to release the heat outside. Keep plants, fences and debris back to at least the clearance the manufacturer specifies.
What is an evaporator coil?
The evaporator coil is the indoor coil, usually above a furnace or inside an air handler. Cold liquid refrigerant flows through it and evaporates, absorbing heat from the air the blower pushes across it. Moisture condenses on the cold coil and drains away, which is how an AC dehumidifies. A dirty or frozen evaporator coil reduces cooling.
What is a TXV?
A TXV, or thermostatic expansion valve, controls how much refrigerant enters the evaporator coil. It senses the temperature of refrigerant leaving the coil and opens or closes to keep the coil working efficiently as the load changes. Systems with a TXV are usually charged by checking subcooling. A stuck TXV can cause poor cooling or a frozen coil.
What is static pressure?
Static pressure is the resistance air meets as it moves through ducts, filters, coils and grilles, measured in inches of water column. It works like blood pressure for your duct system. High static pressure means restricted airflow, from undersized ducts, a clogged or too-restrictive filter, or closed vents, and it makes the blower work harder and reduces efficiency.
What is a heat exchanger?
In a gas furnace, the heat exchanger is the metal chamber that hot combustion gases pass through. House air flows over the outside of it and picks up heat without mixing with the exhaust. A cracked heat exchanger can let carbon monoxide into the air stream, which is why ENERGY STAR recommends a professional check each fall.
What is superheat and subcooling?
They are calculations technicians use to judge refrigerant charge. Superheat is how many degrees refrigerant vapor is heated above its boiling point at the evaporator outlet. Subcooling is how many degrees liquid refrigerant is cooled below its condensing point at the condenser outlet. Correct values depend on the equipment and conditions and come from the manufacturer.
What is a plenum?
A plenum is the box-shaped section of ductwork attached directly to the air handler or furnace. The supply plenum distributes conditioned air into the supply ducts; the return plenum collects air coming back. Leaks at plenum connections are common in attics and waste cooled air. Florida forbids using framing cavities as ducts or plenums.
What is a line set?
A line set is the pair of copper tubes connecting the outdoor unit to the indoor coil: a larger, insulated suction line that carries cool vapor and a smaller liquid line. When replacing a system, the contractor will decide whether the existing line set can be reused or must be replaced for size, condition or refrigerant compatibility.
What is a contactor?
A contactor is an electrical switch in the outdoor unit. When the thermostat calls for cooling, a low-voltage signal pulls the contactor closed, sending full power to the compressor and fan. Contacts can pit or stick over time, especially after storms or insect nests, leaving the unit dead or running nonstop. Replacement is a common, moderate repair.
What is a capacitor?
A capacitor stores and releases electrical energy to help start and run the compressor and fan motors. Heat shortens capacitor life, so failures are common in Texas and Florida summers. Signs include a humming outdoor unit with a fan that will not spin. Capacitors can hold a dangerous charge even with power off, so leave replacement to a technician.
What does tonnage mean?
Tonnage is cooling capacity. One ton equals 12,000 Btu per hour, so a 3-ton system delivers 36,000 Btu/hr. The term comes from the cooling effect of melting a ton of ice in a day. The right tonnage comes from a Manual J load calculation, not from square footage alone, and bigger is not better in humid climates.
What is BTU?
A British thermal unit is the heat needed to raise one pound of water by 1°F. AC and furnace capacity are rated in Btu per hour. Florida's Class B AC license is limited to 500,000 Btu of heating per system, and Texas's Class B license to 1.5 million Btu per hour, which shows how the unit appears in law as well as on nameplates.
Sources
- 10 CFR 430.32, Energy conservation standards (eCFR)
- EPA SNAP, Substitutes in residential and light commercial AC and heat pumps
- EPA, Technology Transitions HFC restrictions by sector
- EPA, Residential AC and the phaseout of HCFC-22
- EPA, AIM Act phasedown fact sheet (May 2026)
- EPA, Section 608 technician certification
- ENERGY STAR, Duct sealing
- ENERGY STAR, Maintenance checklist
- ENERGY STAR, Air-Source Heat Pump key product criteria
- EIA, Degree days explained
- NWS, Heat index
- CPSC, Carbon Monoxide Information Center
- Florida Building Code, Energy Conservation (2023), Residential Chapter 4
- Florida Building Code, Residential (2023), Chapter 14
- Texas Occupations Code Chapter 1302
- Florida Statutes Chapter 489
- Florida Statutes §713.135
- Trane, Next generation refrigerant
- Trane, 6 Ways to Prepare Your A/C for Storms
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


