Local Guide · AC and heating
Do You Need a Permit to Replace an AC in Texas or Florida? Rules by City, Who Pulls It, and What Inspectors Check
In Florida, state law requires a permit for AC replacement almost everywhere. In Texas, permits are set city by city, and big cities like Houston require them. Here is who pulls the permit, what the inspection checks, what changed in Florida's 2025 and 2026 permit laws, and what unpermitted work can cost you.
Usually yes. Florida Statute 553.79 makes it unlawful to alter or repair a building without a permit, and the new $7,500 small-job exemption excludes all mechanical work, so AC changeouts still need one. In Texas, cities set permit rules: Houston requires a mechanical permit and inspection for condenser, coil and furnace replacements, and Dallas, San Antonio and Austin issue trade permits. Your licensed contractor normally pulls the permit and schedules the inspection.
Key facts
- Florida law makes it unlawful to construct, alter, modify or repair a building without first obtaining a permit, unless otherwise provided by law (Fla. Stat. Section 553.79(1)(a)).
- Florida's new exemption for single-family work under $7,500 (Ch. 2026-63, effective July 1, 2026) does not apply to any mechanical, electrical, plumbing, gas or structural work (Section 553.79).
- Florida local governments must act on mechanical permits for an existing single-family home within 5 business days of a complete application when the work is under $15,000 and a local plans reviewer is used (Section 553.792).
- Florida lists HVAC replacements and ductwork or fan replacements as single-trade inspections a private provider may perform (Section 553.791).
- Starting work that needs a Florida building permit without one is a prohibited act for contractors (Section 489.127(1)(h)).
- Houston requires a mechanical permit and inspection for new or replacement AC installations, including condenser, evaporator and furnace replacements and duct alterations.
- In Texas, work by people exempt from state AC licensing, such as homeowners, is still subject to city permits and inspections (Tex. Occ. Code Section 1302.052).
- TDLR's penalty schedule lists "failed to obtain permit" as a violation for Texas ACR licensees.
- Florida's energy code requires replacement systems to be sized with ACCA Manual S based on Manual J loads, and indoor and outdoor units to be matched (FBC-Energy R403.7.1, R501.7).
- A Florida notice of commencement is not required for a direct contract to repair or replace an existing heating or AC system under $15,000 (Section 713.135).
Does replacing an AC always require a permit?
In Florida, almost always. In Texas, it depends on where you live, but in the large cities the answer is yes.
| Situation | Texas | Florida |
|---|---|---|
| Full system replacement (condenser and coil or air handler) | Permit required in Houston, and trade permits issued in Dallas, San Antonio and Austin; set by each city | Permit required under Section 553.79 |
| Condenser only, or air handler only | Houston requires a permit for condenser, evaporator and furnace replacements | Permit required; replacing a functional unit like a condenser is not a "repair" under FBC-Energy R501.7 |
| Duct replacement or alteration | Houston requires a permit for duct alterations | Permit required; HVAC and ductwork replacements are single-trade inspections (Section 553.791) |
| Ductless mini-split | Treated as AC equipment; check city rules (Houston lists new AC installations) | Permit required; the $7,500 exemption excludes mechanical work |
| Window or plug-in portable unit | Generally no permit | Generally no permit |
| Small repairs (capacitor, contactor, refrigerant leak repair) | Usually no permit; confirm with city | Repairing part of a functional unit is treated differently from replacing it; confirm with your building department |
| Unincorporated county areas | Many have no mechanical permit program; state AC code standards still apply to licensees | County building departments issue permits |
The difference comes from how each state is built. Florida has one statewide building code, the Florida Building Code, and a statewide permit law. Texas leaves building permits to cities. Texas does regulate AC contractors statewide through TDLR, and TDLR's rule 16 TAC Section 75.100(e) says the standard for AC work in a city is the code that city adopted. Where no code has been adopted, the standard is the applicable International Residential Code for one- and two-family homes, plus the International Fuel Gas Code and International Energy Conservation Code.
Florida: what the statewide permit law requires
Section 553.79(1)(a) of the Florida Statutes says that, unless otherwise provided by law, it is unlawful for any person, firm, corporation or government to construct, erect, alter, modify, repair or demolish any building without first getting a permit from the enforcing agency.
Several recent laws changed the edges of that rule. Here is where they stand in November 2026:
| Law | Effective | What it does for AC work |
|---|---|---|
| Ch. 2026-63 (HB 803), Section 553.79 | July 1, 2026 | Exempts single-family owners and their contractors from building permits for work under $7,500, but not for mechanical, electrical, plumbing, gas or structural work, and not in flood hazard areas. AC replacements still need a permit. |
| Ch. 2026-63 (HB 803) | July 1, 2026 | A county building permit for a single-family dwelling expires 1 year after issuance or on the effective date of the next Florida Building Code edition, whichever is later. |
| Section 553.792 (amended by ch. 2024-191 and ch. 2026-63) | In effect | Local governments must approve, approve with conditions, or deny mechanical permits for an existing single-family home within 5 business days of a complete application when the work is under $15,000 and a local plans reviewer is used. |
| Ch. 2025-140 (HB 683) | July 1, 2025 | Requires local building officials to issue permits within set timeframes for certain single-trade plan reviews, a category covering HVAC replacements, and allows certain inspections in person or virtually. |
| Section 553.791 | In effect | Lets owners or contractors use a private provider for single-trade inspections, including HVAC replacements and ductwork or fan replacements. A single-family owner or contractor may switch to a private provider after work starts by notifying the building official before the next scheduled inspection. |
One note: our research brief flagged a "HB 1383" permit streamlining bill. We could not confirm that bill number or its effect from the Florida Legislature's records, so this guide relies only on the laws above, which we read in full.
Orlando shows how the $7,500 exemption works in practice. The city requires owners to submit an exemption request with the contract or documents showing the nature and value of the work, to confirm the property is not in a flood zone, and it reviews requests within five business days. Because mechanical work is excluded, you cannot use it for an AC changeout even if the price is under $7,500.
Texas: city-by-city permit rules
Texas cities run their own permit programs. Here is what the four largest metros publish.
Houston
The Houston Permitting Center requires a mechanical permit and inspection for new or replacement residential and commercial AC installations, including condenser, evaporator and furnace replacements and duct alterations. A mechanical inspector must inspect and approve all permitted work before the project is finalized, and the contractor typically schedules inspections. Houston's Mechanical Inspections section (832-394-8850) also registers state-licensed HVAC contractors with the city and keeps a list of registered third-party energy technicians, who do certain energy-code testing.
Dallas
Dallas issues residential permits, including trade permits, through its DallasNow online portal. The city publishes plumbing and mechanical information and a Homeowner's Exemption from Contractor Registration form for owners doing their own work. Questions: 214-948-4480.
San Antonio
CPS Energy's rebate rules say HVAC replacements inside San Antonio city limits must have a permit number to qualify for rebates, which reflects the city's permit requirement for HVAC change-outs. Confirm current details with the City of San Antonio Development Services Department.
Austin
Austin Energy says all required City of Austin permits must be in place for an AC replacement to qualify for its rebate, and it reserves the right to do a post-installation inspection. Confirm permit details with the City of Austin Development Services Department.
Fort Worth, suburbs and rural areas
We did not load Fort Worth's or suburban cities' permit pages for this guide. Call the city's building or development services office, or search "[city name] mechanical permit." In unincorporated parts of a county, there is often no city permit program at all. TDLR's code standards still apply to the licensed contractor, but nobody inspects the work unless you hire a third-party inspector.
Registration fees
Since Sept. 1, 2021, Texas Occupations Code Section 1302.304 bars cities from charging TDLR-licensed contractors a registration fee, though they may still charge permit fees. Houston's page still describes paying a registration fee through iPermits, so contractors who are charged one may want to ask the city how it squares with Section 1302.304.
Who pulls the permit: homeowner or contractor?
In nearly every case, the licensed contractor should pull it. That is how both states' systems are designed.
- Florida: before issuing a permit, each city or county building department must require the contractor to verify his or her CILB certification or registration number (Section 489.119(5)(a)). A contractor who takes more than 10% of the price as a deposit on residential work must apply for permits within 30 days and start within 90 days after permits issue, unless there is just cause or a written agreement (Section 489.126(2)(a)).
- Texas: TDLR contracting companies must give cities a list of authorized agents who may pull permits under the company's license (16 TAC Section 75.71(a)(5)).
Can a homeowner pull their own HVAC permit?
Florida (owner-builder): yes, if you will do or directly supervise the work yourself on your own one- or two-family home that is not for sale or lease. You must personally appear and sign the permit application and show you understand the state's owner-builder disclosure statement (Section 489.103(7)). If you sell or lease within 1 year, the law presumes the work was for sale. Jacksonville limits owner permits to the owner's primary residence, not for sale or rent, with the owner's name on the deed and a signed Owner's Affidavit. Miami-Dade requires an additional form for owner-builder mechanical permits.
Texas: the state licensing law exempts a person doing AC work on a building owned solely by that person as his or her home (Section 1302.053), but that work is still subject to city permits and inspections (Section 1302.052). Dallas, for example, offers a homeowner's exemption from contractor registration form.
Warning: never pull an owner-builder permit for work someone else is doing. If an installer asks you to, he is likely unlicensed, and you take on the legal responsibility for the job. See HVAC scams and red flags.
How much does an AC permit cost?
Permit fees are set by each city or county and change often, so we do not list dollar amounts here. Check:
- Houston: the Code Enforcement permit fee schedule linked from the Houston Permitting Center's mechanical inspections page.
- Dallas: the DallasNow portal and the city's fee schedule.
- Miami-Dade: the county's Mechanical Fee Sheet, which is part of the mechanical permit application.
- Jacksonville, Tampa, Orlando: each city's building division fee schedule.
Florida law limits how fees work. Section 553.79 says inspection fees may not be based on the total cost of a project and may not exceed the actual inspection costs the local agency incurs.
On a quote, the permit fee should be a listed line item or clearly included. If a contractor offers a lower price "without the permit," that is not a discount; it is a violation that shifts risk to you. See how to compare HVAC quotes.
What does an AC inspection check?
Inspectors check that the installation meets the adopted mechanical, electrical, fuel gas and energy codes. Exact checklists vary; Miami-Dade, for instance, publishes Residential Mechanical Plan Review Guidelines and a Mechanical Inspection checklist for the 8th Edition (2023) Florida Building Code. Common items include:
Sizing and matching (Florida energy code)
- Equipment sized with ACCA Manual S based on loads calculated with ACCA Manual J or another approved method (FBC-Energy R403.7.1). Safety factors and "future expansion" allowances are not allowed.
- Cooling capacity at least the calculated load but no more than 1.15 times it, or the closest size the manufacturer offers, with latent (moisture removal) capacity meeting the latent load (R403.7.1.1). Heat pumps are sized on the cooling load (R403.7.1.2.1).
- Matched indoor and outdoor units, verified by AHRI data, an accredited lab, a manufacturer's letter or a Florida-registered engineer (R501.7).
- Equipment meeting at least the federal minimum efficiency for the region (R403.7.1; Section 553.912).
Ducts
- New duct systems tested for leakage at 25 Pa, with a prescriptive limit of 4 cfm per 100 square feet of conditioned floor area (R403.3.3, R403.3.4). No test is needed when all ducts and the air handler are inside the thermal envelope.
- On changeouts, existing ducts reused with a replacement system need not meet current code if meeting it would require replacing them; ducts with R-6 insulation are considered sufficient (R501.7). Extending existing ducts by less than 40 linear feet in unconditioned space does not trigger duct testing (R503.1.2).
- Attic ducts of 3 inches or more insulated to at least R-8 (R-6 if smaller) for new work (R403.3.1). Framing cavities may not be used as ducts (R403.3.5).
Outdoor unit, drains and flood rules (Florida Mechanical Code)
- Exposed equipment installed to resist wind pressures; units fastened with rated stands, slabs or curbs are deemed to comply (FBC-M 301.15).
- Equipment at grade on a level slab at least 3 inches above adjoining grade, or suspended at least 6 inches above grade (FBC-M 304.10).
- In flood hazard areas, equipment at or above the required flood elevation unless designed to keep water out (FBC-M 301.16).
- Condensate drain sloped at least 1/8 inch per foot, and an auxiliary drain pan or other listed secondary protection where overflow could damage the building (FBC-M 307.2.3).
Typical items in Texas inspections
Texas cities apply their adopted codes; the statewide residential energy code baseline is the 2015 IECC, effective Sept. 1, 2016, per the U.S. Department of Energy. Inspectors typically look at the electrical disconnect and wiring, refrigerant line insulation, condensate drain and secondary protection, equipment clearances, gas venting on furnaces, and duct connections. Ask your city for its mechanical inspection checklist.
For more on sizing, see AC sizing and Manual J; for install-day expectations, see AC installation day.
Notice of commencement and liens on Florida AC jobs
Florida's lien law adds a document many homeowners have never heard of: the notice of commencement. Owners generally must record one before starting an improvement and post it on site before the first inspection (Section 713.13).
- There is a specific carve-out: the notice-of-commencement permit requirement does not apply to a direct contract to repair or replace an existing heating or AC system for less than $15,000 (Section 713.135).
- Jacksonville requires a recorded notice of commencement when improvements exceed $5,000, or $15,000 for mechanical work.
- Direct contracts over $2,500 on homes of up to four units must include a bold lien law warning signed by the owner (Section 713.015).
Texas uses a different system. Before signing a residential construction contract, the Texas original contractor must give you a "Know Your Rights and Responsibilities" disclosure (Property Code Section 53.255). See mechanic's liens and HVAC work.
What happens if my AC was installed without a permit?
Unpermitted AC work is common, and it is fixable. But it creates real risks.
Risks
- Safety and performance: no one independently checked sizing, wiring, drains or gas venting. Oversized systems in humid Houston or Miami homes can short-cycle and leave the air damp.
- Rebates: Austin Energy and CPS Energy require permits for HVAC rebates. Florida utility programs may have similar rules; check before you buy.
- Home sale: buyers, inspectors and appraisers may check city permit records. An AC with no permit on file can trigger questions, a price cut, or a demand to permit it before closing. Talk to your real estate agent or a real estate attorney about what you must disclose. See buying or selling a home: AC inspection.
- Insurance: if unpermitted work causes a fire or water damage, the insurer may ask whether the work was permitted. Ask your insurer how your policy treats it.
- Fines: in Jacksonville, starting work without first applying for a permit is punishable by a $250 fine. Ask your city whether an after-the-fact permit carries extra fees.
- The contractor's license: Florida contractors can be disciplined for proceeding without permits and inspections (Section 489.129(1)(o)), and TDLR lists failure to obtain a permit as a violation.
How to fix it
- Search your city or county permit records by address to confirm whether a permit was issued and finaled.
- If the installer was licensed, ask them to pull an after-the-fact permit and schedule inspection at their cost. In Florida, a written certified-mail demand creates a record under Section 489.126.
- If they refuse, file a complaint with TDLR (Texas) or DBPR (Florida).
- Hire another licensed contractor to permit and inspect the system, and correct anything the inspector flags.
Why did my contractor not pull a permit?
Common reasons, from innocent to not:
- Timing: in a no-cooling emergency, some contractors start the job and apply for the permit right away. Ask whether your city allows that, and get the permit number in writing.
- Price: skipping the permit saves the fee and the time spent waiting for an inspector. That saving is not legal.
- The contractor is not licensed and cannot pull one. Check the license: Texas TDLR lookup or Florida DBPR lookup.
- Work outside city limits in Texas, where there may be no permit program.
Put the permit in your contract: "Contractor will obtain all required permits, schedule all inspections, and provide a copy of the final approved inspection."
Permits after a hurricane or flood
Storm repairs still need permits, but local governments often publish fast-track guidance. Tampa, for example, posted a Post-Hurricane Permit Guide in April 2026. In Florida, unlicensed contracting during a declared state of emergency is a third-degree felony (Section 489.127(2)(c)), so verify every crew.
If equipment was flooded, Florida's flood-hazard rule (FBC-M 301.16) may require the replacement to be raised to the required flood elevation. Ask your building department before ordering a new condenser stand. See hurricane prep for your AC.
How to choose a provider
- Ask the contractor, in writing, whether the price includes the permit and inspection.
- Verify the contractor's license before signing (TDLR in Texas, DBPR in Florida).
- Get the permit number before or on install day, and look it up on your city's or county's portal.
- In Florida, confirm the system was sized with Manual J and Manual S and that the units are AHRI-matched.
- Be home or available for the final inspection, or ask for photos of the inspection card.
- Keep a copy of the final approved inspection with your home records.
- Check rebate rules: Austin Energy and CPS Energy require permits.
- Do not sign an owner-builder permit for work someone else is doing.
- For a home you are buying, search permit records for the AC's install date.
- If work was not permitted, ask the installer to pull an after-the-fact permit, then escalate to TDLR or DBPR.
Related ac and heating guides
- Do HVAC Contractors Need a License in Texas? TDLR ACR Licenses, Technicians and How to Verify One
- Does an AC Contractor Need a License in Florida? CILB Class A, B and C, Certified vs Registered, and How to Check
- What Size AC Do I Need? Manual J, Tonnage Myths and the Rule-of-Thumb Trap
- AC Installation Day: Step-by-Step, Commissioning and What to Check Before You Pay
- Buying or Selling a Home: Inspecting the AC, Age, Disclosure and Negotiation
- How Do You Compare AC Replacement Quotes? A Line-by-Line Checklist for Texas and Florida
- Mechanic's Liens From AC Work: Texas and Florida Homeowner Protections
- HVAC Scams and Upsells: 20 Red Flags Before You Sign
AC and heating by state and city
Questions people ask
Do I need a permit to replace my AC in Florida?
Yes. Florida Statute 553.79 requires a permit to alter, modify or repair a building unless the law provides otherwise, and AC replacement is mechanical work. The new exemption for single-family jobs under $7,500, effective July 1, 2026, specifically excludes mechanical, electrical, plumbing, gas and structural work. Your licensed contractor normally pulls the permit, and for mechanical permits under $15,000 on existing single-family homes, the local government must act within 5 business days of a complete application when a local plans reviewer is used.
Does Houston require a permit for AC replacement?
Yes. The Houston Permitting Center requires a mechanical permit and inspection for new or replacement residential and commercial AC installations, including condenser, evaporator and furnace replacements and duct alterations. A city mechanical inspector must approve the work before the project is finalized, and the contractor usually schedules the inspections. Contractors must also register their state license with the city's Mechanical Inspections section.
Do mini-split installs need a permit?
In Florida, yes, because a mini-split is mechanical work and the $7,500 exemption excludes mechanical work. In Texas, it depends on the city, but cities that permit AC installations generally treat mini-splits the same way. TDLR also says mini-splits are split systems that require a licensed ACR contractor for work done for the public. Only window and plug-in portable units are normally free of permits and licensing in both states.
Can I pull my own AC permit in Florida?
Only as an owner-builder under Section 489.103(7), and only if you will do or directly supervise the work yourself on your own one- or two-family home that you are not selling or renting. You must sign the permit application in person and acknowledge the state's disclosure statement. Some cities add rules, such as Jacksonville's Owner's Affidavit and primary-residence requirement. Do not pull an owner-builder permit for work an unlicensed person is doing.
Will unpermitted AC work affect selling my house?
It can. Buyers, home inspectors and lenders' appraisers may check permit records. A replacement with no permit on file can lead to repair requests, price negotiation or a requirement to permit it before closing. Fixing it usually means an after-the-fact permit and inspection by a licensed contractor. Ask a real estate agent or attorney in your state about disclosure duties before listing.
Do Texas counties require AC permits outside city limits?
Many unincorporated areas have no mechanical permit program. TDLR's rule 75.100(e) says that where no code has been adopted, the standard for licensed AC work is the applicable International Residential Code for one- and two-family homes, with the International Fuel Gas Code and International Energy Conservation Code. Your contractor must still be licensed by TDLR. Call your county to confirm, since some counties and special districts have their own rules.
How long is a Florida building permit good for?
Under Ch. 2026-63, effective July 1, 2026, a county building permit for a single-family dwelling expires 1 year after issuance or on the effective date of the next edition of the Florida Building Code, whichever is later. City rules and inspection deadlines may differ, so ask your building department. AC replacements usually finish well inside that window.
Can I use a private inspector for my AC replacement in Florida?
Yes. Section 553.791 lists HVAC replacements and ductwork or fan replacements as single-trade inspections a private provider may perform for the homeowner or contractor instead of the local building department. If work has already started, a single-family owner or contractor can switch to a private provider by notifying the building official before the next scheduled inspection.
Sources
- Florida Statutes Section 553.79, Permits; applications; issuance; inspections
- Florida Statutes Section 553.791, Alternative plans review and inspection
- Florida Statutes Section 553.792, Building permit application to local government
- Florida Statutes Section 553.912, Air conditioners
- Laws of Florida Ch. 2026-63 (HB 803)
- Laws of Florida Ch. 2025-140 (HB 683)
- Florida Statutes Chapter 489, Contracting
- Florida Statutes Section 713.13, Notice of commencement
- Florida Statutes Section 713.135, Notice of commencement and permits
- Florida Statutes Section 713.015, Mandatory lien law disclosure
- Florida Building Code, Energy Conservation 2023, Chapter 4 Residential (UpCodes)
- Florida Building Code, Energy Conservation 2023, Chapter 5 Existing Buildings (UpCodes)
- Florida Mechanical Code 2023, Chapter 3 (UpCodes)
- City of Orlando: Residential Building Permit Exemption
- Miami-Dade County: Mechanical Permits
- City of Jacksonville: Residential Permits
- City of Tampa: Post-Hurricane Permit Guide
- Houston Permitting Center: Mechanical Inspections
- City of Dallas: Residential Permits
- CPS Energy: HVAC Rebate Specifications
- Austin Energy: AC Rebates
- Texas Occupations Code Chapter 1302
- 16 Tex. Admin. Code Section 75.100, Technical Requirements
- 16 Tex. Admin. Code Section 75.71, Responsibilities of the Contracting Company
- TDLR: ACR Penalties and Sanctions
- U.S. DOE Building Energy Codes Program: Texas
- Texas Property Code Chapter 53
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


