New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Electricians

Home Electrical Safety Checklist: 40 Things to Check, Room by Room

A 40-point, room-by-room electrical safety walk-through based on CPSC guidance, with Texas and Florida additions for heat, humidity, hurricanes, generators and insurance inspections.

To check your home's electrical safety, walk every room looking for warm or loose outlets, missing cover plates, damaged or overloaded cords, extension cords used as permanent wiring and bulbs above fixture ratings. Test GFCIs monthly, keep the panel clear and labeled, and use outdoor-rated cords on GFCI outlets. CPSC suggests repeating the check every six months and having a licensed electrician inspect if it has been more than 10 years.

Key facts

  • CPSC staff recommend going through its Home Electrical Safety Checklist every six months (Pub. 513).
  • CPSC advises a licensed electrician's check if it has been more than 10 years since the last inspection or if warning signs appear.
  • USFA estimates 23,700 residential electrical malfunction fires in 2023, with 305 deaths and about $1.5 billion in losses.
  • CPSC recommends testing GFCIs and AFCIs monthly, since they can fail without showing signs.
  • CPSC recommends flipping each breaker off and on three times at least once a year so breakers do not stick.
  • Extension cords should be used only temporarily and be at least 16 AWG unless 18 AWG with fuse protection (CPSC Pub. 5032).
  • Space heaters should be at least 3 feet from combustibles such as drapes and newspapers (CPSC).
  • CPSC says never backfeed house wiring by plugging a generator into a wall outlet.

How to use this checklist

This is a 40-point walk-through you can do yourself in about an hour, with no tools except a lamp or a plug-in night light and a flashlight. It is built on the U.S. Consumer Product Safety Commission's room-by-room Home Electrical Safety Checklist (Publication 513), with additions for Texas and Florida homes: heat, humidity, hurricanes, flooding, generators and the insurance inspections common in Florida.

Three rules before you start:

  • Look, don't open. Do not remove the panel cover (the inner "dead front"). CPSC's wiring hazards guide says removing the service-panel cover is a job for a qualified electrician.
  • Use the back of your hand to feel for heat on cover plates and the panel door. Warm can be normal for a dimmer. Hot is not.
  • Write it down. For every "no," note the room and the problem. That list is what you hand an electrician, and it keeps the visit short.

CPSC staff suggest going through their checklist every six months, for example when you change your clocks or test smoke alarms. A licensed electrician's inspection is a separate, deeper check (see "How often should a home be inspected?" below).

Stop now: warning signs that need an electrician first

If you notice any of these, skip the checklist and call a licensed electrician. CPSC lists them as electrical system hazard warning signs:

  • Dimming or flickering lights
  • Sizzling or buzzing sounds
  • A smell of overheated plastic
  • Plugs that pull out of the outlet too easily
  • Flashes or showers of sparks
  • Hot switch plates or outlet covers
  • Fuses that blow, or breakers that need resetting, often

Add these from CPSC's other guidance: any shock from an appliance (other than static) means do not touch it, turn it off at the breaker and have it checked, because CPSC says a shock indicates an extremely hazardous wiring condition. If you see smoke or flames, leave and call 911. Our guides on burning smells, shocks and tingles, flickering lights and when it is an emergency explain what to do next.

Every room (checks 1 to 10)

  1. Bulbs match the fixture. Each bulb should be at or below the wattage marked on the fixture. CPSC says a higher-wattage bulb than recommended can overheat the fixture, wiring or nearby combustibles. Unmarked fixture? CPSC suggests 60 watts or less (25 watts for unmarked fixtures with miniature bulbs). LED bulbs use far fewer watts for the same light, which helps.
  2. Outlets and switches are cool. CPSC says unusually warm outlets or switches may mean a loose connection that can start a fire. Stop using that outlet until an electrician checks it.
  3. Plugs fit snugly. Loose-fitting plugs can overheat, CPSC notes, because a loose connection cannot carry much current without getting hot. A worn outlet is a cheap fix for an electrician. See outlet problems.
  4. Every outlet and switch has a cover plate. Exposed wiring is a shock hazard.
  5. Cords are not damaged. No frayed, cracked, cut, chewed or taped cords. Replace them. CPSC warns never to tape damaged insulation.
  6. Cords are not under rugs or furniture, and not stapled or nailed. Weight and foot traffic crush insulation; nails and staples cut it.
  7. Cords are not wrapped tightly around objects or bundled while in use. Wrapped cords trap heat.
  8. No extension cord is doing a permanent job. CPSC says extension cords should be used only temporarily and are not as safe as permanent wiring. If you need one every day in the same spot, you need another outlet.
  9. Space heaters carry a testing-lab mark (UL, ETL or CSA), sit on a stable surface, are at least 3 feet from drapes, bedding and paper, and plug directly into a wall outlet, never a cord or power strip.
  10. Three-prong plugs are never forced into two-prong outlets. Never break off the ground pin. If you use an adapter, CPSC says its grounding tab or wire must be connected to the outlet cover's center screw, and it only works if that box is actually grounded, which many older homes are not. See two-prong outlets.

Kitchen and laundry (checks 11 to 17)

  1. Outlets near the sink are GFCI protected. A GFCI (ground-fault circuit interrupter) cuts power in a fraction of a second if current leaks to ground, for example through a person. Look for TEST and RESET buttons on the outlet, or a GFCI breaker in the panel.
  2. Test each GFCI monthly. CPSC's method: plug in a lamp and turn it on, press TEST (the lamp should go out), press RESET (it should come back). If the lamp stays on after TEST, replace the GFCI.
  3. Countertop appliances are unplugged when not in use and kept away from the sink.
  4. Cords stay clear of hot surfaces like the range, oven and toaster.
  5. The stovetop area is not storage. No potholders, paper or plastic on or above the range.
  6. Large appliances plug directly into the wall (refrigerator, microwave, dishwasher, washer, dryer). No extension cords or strips.
  7. No shocks or tingles from any appliance or sink faucet. If you get one, turn the circuit off and call an electrician. Do not keep using it.

Electric dryers also need their lint filter cleaned every load and the vent kept clear. Lint is fuel, and the dryer's heating element is the ignition source.

Bathrooms (checks 18 to 21)

  1. Bathroom outlets are GFCI protected and pass the monthly test.
  2. Hair dryers, curling irons and razors are unplugged after use. CPSC notes that even when switched off, a plugged-in appliance can be a shock hazard if it falls into water.
  3. No portable heater in the bathroom. CPSC says portable heaters can be an electrocution hazard in bathrooms. If you must use one, plug it into a GFCI outlet or use a heater with a GFCI plug. A fixed heater fan is a better answer.
  4. The exhaust fan works. Moisture is hard on wiring and devices, and Gulf Coast humidity makes this matter more.

Bedrooms and living areas (checks 22 to 27)

  1. Electric blankets are in good condition, with no charred spots, cracks or exposed wire. CPSC says do not cover an operating electric blanket, do not fold it, and do not tuck in the heated wires. Discard damaged ones.
  2. Entertainment and computer equipment has room to breathe. Do not pack it into a closed cabinet without openings.
  3. Power strips plug straight into a wall outlet, never into another strip or an extension cord, and only run low-draw electronics.
  4. Lamps sit away from curtains and bedding, and halogen or hot bulbs are not near fabric.
  5. Unused outlets are childproofed if young children live or visit (see the childproofing section below).
  6. Phone and e-bike chargers are not charging under pillows, on beds or on couches. Charge on a hard surface, and follow the manufacturer's instructions for lithium-ion batteries. Florida's State Fire Marshal maintains lithium-ion battery safety resources, including after hurricanes.

Garage, attic and the electrical panel (checks 28 to 34)

  1. The panel is easy to reach. Nothing stacked in front of it. In an emergency, someone must be able to shut it off fast.
  2. The panel door closes, no breaker slots are open, and there are no scorch marks, rust or water stains on the door. Rust or water marks on the panel are a call to an electrician, especially after a storm.
  3. Breakers are labeled. See "How do I label my breaker panel?" below.
  4. Breakers are exercised once a year. CPSC recommends turning off the refrigerator, freezer and AC first, then flipping each breaker off and on three times, at least once a year, so breakers do not stick.
  5. Test AFCI and GFCI breakers using their test buttons. CPSC says AFCIs and GFCIs can stop working without showing signs of failure, so regular testing matters. AFCIs (arc-fault circuit interrupters) detect dangerous arcing in wiring.
  6. Fuse boxes have the correct fuse sizes. CPSC warns that the wrong size fuse can let too much current flow and overheat wiring. If you are not sure of the right size, have an electrician identify and label it. See fuse boxes.
  7. Corded power tools have three-prong plugs or are marked double insulated, and are used on GFCI-protected outlets in the garage.

Note the panel's brand and approximate age while you are there. Florida insurers' 4-point inspection forms ask for panel brand, model, age and amperage, and note hazards like double taps and scorching. If your panel is a brand your insurer questions, see Federal Pacific and Zinsco panels.

Outside, pool and storm prep (checks 35 to 40)

  1. Outdoor outlets have weatherproof covers, and covers rated "weatherproof while in use" where something stays plugged in. CPSC notes that most ordinary covers do not keep water out when a cord is plugged in.
  2. Outdoor outlets are GFCI protected. If not, use a portable GFCI until an electrician adds protection.
  3. Outdoor extension cords are marked for outdoor use and have three prongs for three-prong tools.
  4. Pool, spa and hot tub equipment plugs only into working GFCI outlets, and nothing electrical sits where it can fall into water. See pool and spa electrical safety.
  5. The meter base, weatherhead and service mast are intact, not pulled from the wall or leaning. In Texas and Florida these are usually the homeowner's equipment, not the utility's. See meter base responsibility.
  6. Your generator plan is safe. CPSC says never power house wiring by plugging a generator into a wall outlet ("backfeeding"), never run a generator indoors or in a garage, and keep it outside far from windows, doors and vents. Use a transfer switch or interlock installed by an electrician. See transfer switches and interlocks.

After a flood or storm surge: do not turn power back on to anything that got wet. NEMA's 2026 guide on water-damaged equipment says GFCIs, AFCIs, surge protectors, breakers and wiring devices exposed to water should be replaced, not reconditioned, and that salt water residue is especially corrosive and conductive. See flood-damaged electrical.

What causes most home electrical fires?

The U.S. Fire Administration estimates there were 23,700 residential building electrical malfunction fires in 2023, causing 305 deaths, 800 injuries and about $1.5 billion in losses. From 2014 to 2023, those fires rose 2% while deaths fell 19%.

CPSC's guidance points to the same short list of causes again and again: loose or worn connections at outlets and switches that overheat, damaged or overloaded cords, wrong-size fuses and overloaded circuits, and arcing in aging wiring that ordinary breakers do not detect. CPSC says ordinary fuses and breakers do not respond to early arcing and sparking, which is why AFCIs exist.

Older aluminum branch wiring is a special case: a CPSC-sponsored study found pre-1972 homes wired with aluminum were 55 times more likely to have one or more connections reach "fire hazard conditions" than copper-wired homes. See aluminum wiring and our full guide to electrical fire causes and insurance.

Are extension cords and power strips safe long-term?

No. Both are meant for temporary or light use. CPSC says extension cords can overheat and cause fires when overloaded, used with appliances that draw more watts than the cord can handle, or when damaged. Its rules of thumb:

  • Use extension cords only temporarily and unplug them when not in use.
  • Check the cord's rating on its tag or package and do not exceed it. If any part of the cord gets hot, it is overloaded.
  • Use at least 16 AWG cords (18 AWG only with fuse protection). Lower numbers mean thicker wire.
  • Do not run cords under carpets, through doorways or under furniture.
  • Discard old cords missing safety features such as polarized blades and safety closures.
  • Buy cords listed by a recognized lab such as UL, Intertek (ETL) or CSA.

Power strips are fine for TVs, computers and chargers. They are not for space heaters, refrigerators, microwaves, toasters, coffee makers or hair dryers. Never plug a strip into another strip.

Recalls: CPSC's recall database has search categories for "Extension Cords" and "Surge Suppressors or Power Strips." Check your cords and strips there, and register new products with the maker so you get notices.

How do I childproof outlets?

CPSC says children can suffer serious shock and burn injuries if they insert objects into outlets, and recommends safety covers for all unused outlets. Your options, from best to most basic:

  • Tamper-resistant receptacles. These have built-in spring shutters that block a single object, such as a key or hairpin, from entering one slot. They are marked "TR" on the face. An electrician can swap standard outlets for TR outlets, usually quickly.
  • Sliding or self-closing cover plates that replace the standard plate and snap shut when a plug is removed.
  • Plug-in caps. Cheap, but small caps can become a choking hazard and are easy for older toddlers to remove. Choose caps sized so they cannot be swallowed.

Also keep cords out of reach, unplug extension cords when not in use (CPSC advises this specifically for young children), and secure TVs and furniture so cords cannot be yanked.

Electrical hazards for seniors and caregivers

Older adults face the same hazards as everyone, plus a few that matter more:

  • Space heaters and electric blankets. Use heaters with a testing-lab mark and tip-over shutoff, 3 feet from anything that burns. Replace electric blankets with any damage, and do not cover or fold them in use.
  • Trip hazards. Cords across walkways cause falls. Move lamps, add outlets, or use cord covers designed for floors.
  • Reach. If bending to low outlets is hard, an electrician can add outlets at a higher height or install switched outlets so lamps can be turned on at the door.
  • Lighting. Night lights from bedroom to bathroom, and switches at both ends of stairs and halls.
  • Medical equipment. Oxygen concentrators and other devices should plug directly into wall outlets, and caregivers should have a written outage plan. See medical equipment backup power.
  • Smoke alarms. CPSC calls working smoke detectors the most important thing you can do to prevent home fire deaths. Consider interconnected alarms so one sounding sets off all of them. See smoke and CO detectors.

How do I label my breaker panel?

  1. Wait for daylight and get a helper with a phone, or use a plug-in radio you can hear from the panel.
  2. Turn on every light and plug a lamp or night light into outlets room by room.
  3. Switch off one breaker at a time and have your helper report what went dead. Check every outlet, both halves of each duplex outlet, and hardwired items like the garbage disposal, bath fans, doorbell, garage door opener, water heater and AC.
  4. Write specific labels: "Kitchen counter left of sink and dishwasher" is useful; "Kitchen" is not.
  5. Note double-pole (240-volt) breakers for the range, dryer, water heater, AC, pool pump and EV charger.
  6. Print the directory and tape it inside the panel door. Keep a photo on your phone.

Turn off the refrigerator, freezer and AC before cycling breakers, as CPSC advises, and reset any clocks after. If a breaker controls nothing you can find, or one breaker controls an odd mix of rooms, ask your electrician about it at the next visit.

How often should a home's electrical system be inspected?

There is no single legal schedule for owner-occupied homes. CPSC offers practical guidance:

SituationCPSC guidance
Your own room-by-room checklistEvery six months (Pub. 513)
Last professional inspection more than 10 years ago, or any warning signHave a licensed electrician check the system (CPSC electrical safety flyer)
Last inspection 40 or more years agoInspection is overdue (CPSC Guide to Home Wiring Hazards)
Last inspection 10 to 40 years agoAdvisable, especially if large loads were added or warning signs exist
Less than 10 years agoNot needed unless warning signs appear or temporary wiring was added

To find your last inspection date, CPSC suggests looking for a dated, initialed tag or label on the panel door or cover, without removing the cover.

So should you get an inspection every 10 years? It is a reasonable default backed by CPSC's flyer, and sooner if you buy a home, add major loads like an EV charger, have storm or flood damage, or see warning signs.

Texas and Florida triggers that often force an inspection

  • Florida insurance: many carriers require a 4-point inspection for older homes. Citizens' form records panel amperage, age, brand and wiring type, and Citizens tells agents not to submit applications for homes with electrical systems not in good working order. See 4-point inspections.
  • Texas insurance: in September 2026 the Texas Department of Insurance clarified that insurers cannot decline or non-renew a home policy based only on the home's age, but can based on the physical condition of components such as wiring.
  • Buying or selling: see electrical inspections for buyers and sellers.
  • After storm damage to the meter base or mast: utilities such as Oncor and FPL require repairs by a licensed electrician and any required inspection before reconnecting.

How to choose a provider

  • Walk every room with a lamp and flashlight using the 40 checks above.
  • Feel cover plates and the panel door with the back of your hand.
  • Test every GFCI outlet and breaker, and every AFCI breaker, using the test button.
  • Replace damaged cords and remove extension cords doing permanent jobs.
  • Plug heaters and large appliances directly into wall outlets.
  • Clear the area in front of the panel and label every breaker.
  • Install tamper-resistant outlets or self-closing covers where children live or visit.
  • Confirm outdoor outlets are GFCI protected with in-use covers.
  • Plan generator use with a transfer switch or interlock, never backfeeding.
  • Book a licensed electrician if anything is hot, buzzing, sparking or if the last inspection was over 10 years ago.
  • Repeat the checklist every six months.

Related electricians guides

Electricians by state and city

Questions people ask

How do I check my home's electrical safety myself?

Walk room by room with a lamp and a flashlight. Look for warm or loose outlets, missing cover plates, damaged cords, cords under rugs, extension cords used permanently, and bulbs above fixture ratings. Test GFCI outlets monthly with the TEST and RESET buttons. Check that the panel is reachable and labeled, and look for rust or scorch marks without removing the cover. CPSC recommends repeating this kind of check every six months. Anything hot, buzzing, sparking or smelling of burning plastic goes to an electrician.

What are the signs of dangerous wiring?

CPSC lists dimming or flickering lights, sizzling or buzzing sounds, an odor of overheated plastic, plugs that fall out of outlets, sparks, hot switch plates or outlet covers, and fuses or breakers that trip often. A shock from an appliance or faucet is also a red flag. In older homes, ask an electrician about aluminum branch wiring from roughly 1965 to the mid-1970s, cloth-insulated or knob-and-tube wiring, and two-prong outlets with no ground.

Are power strips a fire hazard?

A listed power strip used correctly is not a hazard by itself. Problems come from overloading it with high-wattage appliances such as space heaters, plugging one strip into another, running strips under rugs, and using damaged or old strips without a testing-lab mark. Keep strips for electronics and chargers, plug them directly into a wall outlet, and replace any that are warm, cracked or scorched. Check CPSC's recall search for your model.

Should I get an electrical inspection every 10 years?

CPSC's consumer flyer says to have a licensed electrician check your system if it has been more than 10 years since the last inspection, or sooner if you notice warning signs. Its older wiring guide says an inspection is overdue after 40 years and advisable between 10 and 40 years, especially if you have added big loads. Buying a home, adding an EV charger or recovering from storm or flood damage are also good times for an inspection.

Is it safe to use extension cords outdoors in Texas and Florida heat?

Use only cords marked for outdoor use, sized for the load, with three prongs for three-prong tools, plugged into a GFCI-protected outlet. CPSC says indoor cords cannot withstand outdoor temperature, humidity and mechanical stress. Keep connections out of puddles and sprinkler spray, do not leave cords out in sun and rain for weeks, and unplug them when done. Permanent outdoor needs such as fountains or lighting call for a permanent circuit.

What should I check after a hurricane before turning the power back on?

Do not restore power to anything that was underwater. Look for a pulled-away meter base, a bent mast or downed service wires, and stay away from downed lines. NEMA says breakers, GFCIs, AFCIs, surge protectors and outlets exposed to water should be replaced. Have a licensed electrician inspect, and expect a city inspection before the utility reconnects if the meter base was damaged. Never backfeed a generator through an outlet.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration