New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Fri, Nov 20, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Home EV charger installation

How to Become an EV Charger Installer in Texas or Florida: Licenses, Apprenticeships and Certifications

The license path from apprentice to master in Texas and from journeyman to certified contractor in Florida, what the 2026 NEC adds, and what BLS says about pay and demand.

There is no separate EV charger installer license in Texas or Florida. You become one by becoming a licensed electrician: in Texas, apprentice, journeyman (8,000 hours and an exam) and master (12,000 hours and an exam) under TDLR; in Florida, a local journeyman license and then a DBPR certified or registered electrical contractor license. EVITP training is optional and not required by law.

Key facts

  • TDLR says anyone who performs or offers non-exempt electrical work in Texas must be licensed and work through a licensed electrical contractor.
  • Texas Occupations Code 1305.155 requires 8,000 hours of on-the-job training and an exam for a journeyman electrician license.
  • Texas Occupations Code 1305.153 requires 12,000 hours, two years as a journeyman and an exam for a master electrician license.
  • Texas apprentice licenses need no experience or exam, cost $20 and require supervision by a licensed electrician.
  • TDLR's electrician exams are open book and allow the 2026 NEC, with a passing score of 70 percent.
  • Florida Statutes 489.511 lets anyone 18 or older take the electrical contractor certification exam, with experience paths from 3 to 6 years.
  • Florida Statutes 489.5335 sets journeyman licensing by counties and cities, with a 75 percent exam score and 12,000 hours or a registered apprenticeship.
  • BLS reports median electrician pay of $63,190 in May 2025 and projects 9 percent job growth from 2025 to 2035.
  • The 2026 NEC adds 625.4, requiring permanently installed Level 2 or higher chargers to be installed by a qualified person (trade-press summary).
  • EVITP training is voluntary; DOE AFDC points to its contractor list but state licensing is what the law requires.

Do I need a license to install EV chargers in Texas?

Yes, in almost every case. There is no separate "EV charger installer" license in Texas. Installing a charger is electrical work, and the Texas Department of Licensing and Regulation (TDLR) says anyone who performs, or offers to perform, non-exempt electrical work in Texas must be licensed and must perform that work through a licensed electrical contractor (TDLR electricians).

Texas Occupations Code Chapter 1305 sets the license classes. The ones that matter for chargers are:

LicenseWhat the statute requiresWhat it lets you do
Apprentice electricianAt least 16 years old, learning under a licensed master electrician (Sec. 1305.161)Assist under supervision
Residential wireman4,000 hours of on-the-job training or an approved career and technology program, plus an exam (Sec. 1305.157)Residential electrical work
Journeyman electrician8,000 hours of on-the-job training under a master electrician, plus an exam (Sec. 1305.155)Electrical work under a contractor
Master electrician12,000 hours of on-the-job training, two years as a journeyman, plus an exam (Sec. 1305.153)All electrical work, supervise others, serve as master for a contractor
Electrical contractorBe or employ a master electrician, meet the state proof-of-responsibility rule, and maintain or elect out of workers' compensation (Sec. 1305.159)Sign contracts and pull permits for the company

Source: Texas Occupations Code Chapter 1305. TDLR's current application pages show that a journeyman applicant may apply with at least 7,000 hours of on-the-job training even though the license itself requires 8,000, and that a master applicant must document 12,000 hours and hold a journeyman license for at least two years (TDLR journeyman, TDLR master).

The owner exemption in 1305.003(a)(6) covers an owner who lives in the home and does the work, and only if a city does not specifically regulate it. It does not let you work on other people's homes. See who can install in Texas.

Do I need a license in Florida?

Yes. Florida Statutes 489.505 defines an electrical contractor as a person who has the experience, knowledge and skill to install, repair, alter, add to or design electrical wiring, fixtures, appliances, apparatus and raceways (Fla. Stat. 489.505). A charger circuit is electrical wiring, so the contractor who sells and installs it needs a Florida license. The Florida Department of Business and Professional Regulation (DBPR) says certified licenses are statewide and registered licenses are limited to certain local jurisdictions (DBPR electrical contractors).

Florida splits the ladder differently than Texas:

  • Journeyman: Florida Statutes 489.5335 lets counties and municipalities issue journeyman licenses to people who scored at least 75 percent on a proctored exam, completed a registered apprenticeship or have at least 12,000 hours of on-the-job training, and completed building code coursework. Counties and municipalities must recognize a journeyman license issued by another Florida county or city (Fla. Stat. 489.5335).
  • Electrical contractor (certified): Florida Statutes 489.511 lets anyone at least 18 take the certification exam, with proof of a personal history of honesty, fairness and respect for the rights of others. Experience paths include at least 3 years of management experience within 6 years, at least 4 years as a supervisor or contractor within 8 years, or at least 6 years of comprehensive training, technical education or supervisory experience within 12 years, or combinations (Fla. Stat. 489.511). Electrical contractors from out of state may qualify by endorsement and must complete a 2-hour Florida Building Code course.
  • Registered contractor: limited to the local jurisdictions where you registered.

DBPR gives exams through computer-based testing with an outside vendor, and each license type has its own checklist. Certified and registered licenses expire August 31 of every even year, and each requires 11 hours of continuing education at renewal (DBPR). DBPR notes that under HB 7125 certain convictions older than five years generally cannot be considered for licensure, but listed crimes still can. See who can install in Florida.

What is the path from apprentice to master in Texas?

A typical path looks like this. Hours and exams come from the statute and TDLR pages listed above:

  1. Get an apprentice license. TDLR says there are no experience or exam requirements, the application fee is $20, the license lasts one year and renews annually, and apprentices work under the general supervision of a master electrician, journeyman electrician or residential wireman (TDLR apprentice license). An online application with no criminal convictions earns a temporary license.
  2. Work and train. Log on-the-job hours under a Texas-licensed master electrician. Each supervisor signs an Experience Verification Form. An apprenticeship training program can be recognized by the Texas Workforce Commission, the Texas Higher Education Coordinating Board or the U.S. Department of Labor (Sec. 1305.002).
  3. Sit for the journeyman exam. TDLR allows an application with 7,000 hours. The exam has a knowledge part and a calculations part (since March 11, 2025), it is open book, and you may bring the National Electrical Code, 2026 Edition in a soft-bound copy. A score of 70 percent or better is required. A testing vendor administers it at sites in Houston, Dallas, San Antonio, Austin and other cities (TDLR exam information).
  4. Work as a journeyman for at least two years while logging hours toward 12,000.
  5. Pass the master exam. The application fee is $45 and licenses renew annually.
  6. Start or join a contractor. An electrical contractor must be or employ a master electrician.

The BLS says an electrician apprenticeship usually lasts 4 or 5 years with about 2,000 hours of paid on-the-job training per year plus technical instruction (BLS Occupational Outlook Handbook, electricians). So the timeline to master is typically many years, depending on how many hours you log. Check TDLR for current fees.

Texas exams moved to the 2026 NEC on the same day the commission adopted it. TDLR's bulletin says the commission voted on July 28, 2026 to adopt the 2026 NEC effective September 1, 2026 for all non-exempt electrical work (TDLR bulletin). Study from the 2026 edition, not the 2023.

What is the path in Florida?

Florida's route is more local at the start and statewide at the contractor level.

  1. Enter an apprenticeship or work under a licensed contractor. Florida statute 489.5335 refers to a registered and state-approved apprenticeship program or 12,000 hours of on-the-job training for a journeyman license. We did not load DBPR's list of approved programs, so ask your county or city licensing office and the Florida Department of Education.
  2. Take a proctored journeyman exam through a county or municipality that issues journeyman licenses. Scores of at least 75 percent are required under the statute for exams after October 1, 1997.
  3. Complete the building code coursework required by the Florida Building Commission, or show proof within 6 months.
  4. Gain contractor experience under one of the paths in section 489.511.
  5. Apply to DBPR for the certified or registered electrical contractor license, take the DBPR exam by computer-based testing and complete the checklist. DBPR's page shows a certified fee of $296 and a registered fee of $121 at renewal (DBPR electrical contractors).

Florida's building code edition is changing. The 9th Edition (2026) Florida Building Code takes effect December 31, 2026 and adopts the 2023 NEC, and the edition in effect on the permit application date governs the work. The 8th Edition applies until December 30, 2026 (ICC summary). Confirm which NEC edition DBPR's current exam covers when you apply.

Is EVITP certification required?

Not by Texas or Florida law in the sources we loaded. EVITP is the Electric Vehicle Infrastructure Training Program, a voluntary training and certification program. The U.S. Department of Energy's AFDC says that to find licensed electrical contractors trained in charging station installation, you can refer to the EVITP list of contractors trained and certified in equipment installation (DOE AFDC infrastructure development). We did not load the EVITP website, so check its current requirements and fees there.

What is required is the state electrical license. Some utility programs or incentive programs may ask for specific training, so read each program's rules. DOE also points to NECA 413 as the standard for installation and maintenance of EV chargers, covering Level 1, Level 2 and Level 3 safe installation, system capacity and NEC compliance (DOE, March 2026). Reading and using it is good practice even when no one requires it.

What does the 2026 NEC require of installers?

A trade-press summary of the 2026 NEC reports a new section 625.4 requiring permanently installed EV power transfer equipment, such as Level 2 or higher chargers, to be installed by a qualified person as defined in Article 100 (EC&M top 25 changes to the 2026 NEC). Confirm the exact wording in NFPA 70-2026. The summary also reports:

  • 625.5: permanent field markings on charger enclosures showing supply voltage, phases, frequency, full-load current and short-circuit current rating.
  • 625.43(D): for other than one- and two-family dwellings, an emergency shutoff within sight, between 20 and 100 feet from the equipment.
  • 625.44: 30, 50 and 60 amp receptacles used for EV charging must be listed for EVSE use.
  • Load calculations moved to Article 120, with the charger counted at 100 percent of nameplate in the dwelling optional method (120.82(D)).

A proposed amendment, TIA 1892, would change 625.54 so ground-fault protection applies to receptacles installed for EVSE (NFPA TIA 1892). It is only a proposal. Watch for final action.

In Texas, TDLR adopted the 2026 NEC effective September 1, 2026, with an amendment to 210.8(F) that removes GFCI protection for certain outdoor dwelling HVAC outlets. City amendments may not be less strict than the state code. The Houston Permitting Center told applicants that permit applications on or after September 1, 2026 are reviewed against the 2026 NEC (Houston Permitting Center). For a full list see 2026 NEC charger changes.

Note: 2026 NEC section numbers in this guide come from published trade summaries and may be renumbered in the final adopted text. Confirm them in NFPA 70-2026 or with your electrician and local inspector before relying on them.

How long does it take, and how much do EV charger installers earn?

The BLS Occupational Outlook Handbook gives the most reliable national numbers for electricians, the trade that installs chargers (BLS):

MeasureValue
Median pay for electricians, May 2025$63,190 per year ($30.38 per hour)
Number of jobs, 2025821,000
Projected growth, 2025 to 20359 percent, much faster than the average for all occupations
Typical entry-level educationHigh school diploma or equivalent
ApprenticeshipUsually 4 or 5 years, about 2,000 hours of paid on-the-job training per year plus technical instruction

These are national figures for all electricians, not EV charger specialists, and not Texas or Florida figures. BLS publishes state wage data on its occupational pages, which we did not load. Pay in Houston, Miami and other metros will differ.

Total time to a Texas master license depends on hours worked. At roughly 2,000 hours a year, 8,000 hours takes about four years, and 12,000 hours takes about six, plus the two-year journeyman requirement that can run at the same time. These are arithmetic examples, not guarantees.

Is demand growing?

Charging demand projections point up, but treat them as forecasts. The NREL report The 2030 National Charging Network (2023) estimated that a national network in 2030 could have 26 to 35 million charging ports to support 30 to 42 million plug-in electric vehicles. For a mid-adoption scenario of 33 million vehicles, it described about 28 million ports, including 26.8 million privately accessible Level 1 and Level 2 ports at homes, multifamily properties and workplaces (NREL 2030 National Charging Network). That report is from 2023, before federal incentive changes in 2025 and 2026, so actual growth may differ.

Federal 30C credit for charging property ended for property placed in service after June 30, 2026, and the 30D vehicle credits needed acquisition by September 30, 2025 (IRS Form 8911 instructions). Those changes may slow some demand. On the other side, BLS projects 9 percent growth for electricians from 2025 to 2035. Commercial, multifamily and fleet work also needs licensed electricians. See small business fleet charging and multifamily installation.

Can I help install chargers without a license?

Only in narrow ways. In Texas the apprentice license exists for exactly this: a person at least 16 learning on the job under a licensed master electrician. TDLR says apprentices work under general supervision of a master, journeyman or residential wireman, and it issues a temporary license on request for 21 days to a qualified applicant (Sec. 1305.161). Doing electrical work without a license, or offering to, can lead to a cease and desist order and civil penalties under Chapter 1305.

In Florida, acting as a contractor or advertising as one without being registered or certified is prohibited by section 489.127. It is a first-degree misdemeanor, and a third-degree felony after a prior finding or during a declared state of emergency (Fla. Stat. 489.127). We did not load the Florida rules on unlicensed helpers working under a licensed contractor, so ask DBPR or the local building department before you take a job as a helper.

If you are not an electrician, there are other roles in the charging field that do not need an electrical license, such as site assessment, project coordination, utility applications, sales and customer support. They cannot include doing the wiring.

Where do I take training and exams?

  • Texas exams: TDLR contracts with a testing vendor that runs exams at sites including Abilene, Amarillo, Arlington, Austin, Corpus Christi, Dallas, El Paso, Fort Worth, Harlingen, Houston, Lubbock, McAllen, Midland, San Antonio, Tyler and Waco. Your name must match TDLR records exactly, and you have one year from the application date to meet all requirements (TDLR exam information).
  • Florida exams: DBPR points candidates to its Electrical Examinations Information page for scheduling (DBPR).
  • Apprenticeship programs: TDLR's page links to apprentice training program approval and apprentice enrollments. Programs may be run by employer groups, unions or schools. In Texas, the statute recognizes programs approved by the Texas Workforce Commission, the Texas Higher Education Coordinating Board or the U.S. Department of Labor.
  • Community colleges and technical schools: We did not verify a list of specific programs. Check each college's electrical or construction technology page and ask whether the program counts toward state hour requirements. In Texas, ask TDLR; in Florida, ask your county or city licensing office or DBPR.

Whichever route you choose, ask in writing how the hours you log will be verified. Hours without a licensed supervisor's signature may not count.

How to choose a provider

  • Decide whether you want to work in Texas or Florida, because licenses do not transfer automatically.
  • In Texas, apply for an apprentice license with TDLR and find a master electrician or a recognized training program.
  • Log your on-the-job hours and get each supervisor to sign the verification form.
  • In Florida, find an apprenticeship or a licensed contractor and ask your county or city about its journeyman exam.
  • Study the correct NEC edition: 2026 for Texas exams; confirm the edition for your Florida exam.
  • Read NEC Article 625 and NECA 413 for charger work.
  • Schedule your exam through the state's testing vendor and bring the allowed code book.
  • Plan for a contractor license if you want to sign contracts and pull permits.
  • Consider EVITP training as an optional credential.
  • Keep records of every license, hour log, exam score and renewal date.

Related home ev charger installation guides

Home EV charger installation by state and city

Questions people ask

Do I need a license to install EV chargers in Texas?

Yes. TDLR says anyone who performs or offers non-exempt electrical work must be licensed and work through a licensed electrical contractor. There is no separate EV installer license. Most charger installers are journeymen or masters working for a licensed electrical contractor, and apprentices help under supervision.

Do I need a license in Florida?

Yes. Florida Statutes 489.505 defines electrical contracting as installing, repairing, altering or adding to electrical wiring, fixtures, appliances, apparatus and raceways, and 489.127 prohibits acting as a contractor without being registered or certified. DBPR licenses electrical contractors, and counties and cities issue journeyman licenses.

What is the path from apprentice to master in Texas?

Get an apprentice license (no experience or exam, $20, annual renewal), log on-the-job hours under a master electrician, pass the journeyman exam (8,000 hours required by the statute, with TDLR allowing application at 7,000), work two years as a journeyman and log 12,000 hours, then pass the master exam. An electrical contractor must be or employ a master.

What is the path in Florida?

Complete a registered apprenticeship or 12,000 hours of training, pass a proctored journeyman exam with at least 75 percent through a county or city, and complete building code coursework. For a contractor license, meet one of the experience paths in section 489.511 and pass the DBPR exam. Certified licenses are statewide and registered ones are local.

Is EVITP certification required?

No law in the sources we loaded requires it. EVITP is a voluntary training program, and DOE AFDC points to its list of trained contractors. Your state electrical license is what the law requires. Some programs may ask for training, so read their rules.

How long does it take to become an EV charger installer?

BLS says an electrician apprenticeship usually lasts 4 or 5 years with about 2,000 hours of paid training per year. At that pace, Texas journeyman hours (8,000) take about four years and master hours (12,000) about six. Time varies with the hours you log and how soon you pass exams.

How much do EV charger installers earn?

BLS reports median pay of $63,190 a year for all electricians in May 2025, which is $30.38 an hour. It does not publish a separate figure for EV charger installers, and state or metro pay differs. Check BLS state wage data and local job listings.

What training exists for installers?

Apprenticeship programs recognized by the Texas Workforce Commission, the Texas Higher Education Coordinating Board or the U.S. Department of Labor count in Texas. Community colleges and technical schools may offer electrical programs, but confirm in writing whether the hours count toward state licensing. NECA 413 and NEC Article 625 are the key charger references.

What does the 2026 NEC require for installers?

A trade summary reports that section 625.4 requires permanently installed Level 2 or higher chargers to be installed by a qualified person. Other changes include field markings, a listed-receptacle rule for 30, 50 and 60 amp EV receptacles, and new load calculation placement. Texas applies the 2026 NEC from September 1, 2026. Confirm text in NFPA 70-2026.

Can I install without a license as a helper?

Only as a licensed apprentice in Texas, working under a master electrician. In Florida, acting as a contractor without a license is prohibited and the rules on helpers were not verified here, so ask DBPR or the local building department first. Unlicensed work can lead to penalties.

Where do I take exams?

In Texas, TDLR's testing vendor runs exams in cities such as Houston, Dallas, San Antonio and Austin, with a 70 percent passing score and an open-book 2026 NEC. In Florida, DBPR exams are computer-based through an outside vendor, and counties or cities administer journeyman exams.

Is demand growing?

BLS projects 9 percent job growth for electricians from 2025 to 2035. A 2023 NREL report projected 26 to 35 million charging ports by 2030 nationwide, mostly private Level 1 and Level 2. That is a forecast, and federal incentive changes in 2025 and 2026 could change the pace.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration