Local Guide · Home EV charger installation
2026 NEC Changes for EV Chargers: What Texas (Sept 1, 2026) and Florida (Dec 31, 2026) Homeowners Need to Know
Texas started using the 2026 NEC on September 1, 2026. Florida's next code edition starts December 31, 2026 with the 2023 NEC. Here is what changed for EV chargers and which edition governs your permit.
Texas adopted the 2026 NEC effective September 1, 2026 for all non-exempt electrical work, in cities and counties. Florida uses the 8th Edition (2023) Florida Building Code until December 30, 2026. The 9th Edition, with the 2023 NEC, starts December 31, 2026. In Florida the permit application date decides the edition. The 2026 NEC adds new EV rules in Article 625.
Key facts
- TDLR: the Texas commission voted on July 28, 2026 to adopt the 2026 NEC effective September 1, 2026 for all non-exempt electrical work, inside cities and in counties.
- 16 TAC 73.100 adopts the 2026 NEC; the adoption was published August 28, 2026 (51 TexReg 5776).
- Texas cities may amend the state NEC but not go below it (Occ. Code 1305.201 and 1305.202, TDLR).
- Texas amended 210.8(F) so GFCI is not required on outdoor dwelling HVAC outlets; this does not cover EV chargers.
- Houston reviews permit applications filed on or after September 1, 2026 against the 2026 NEC.
- Florida's 9th Edition Building Code starts December 31, 2026 and adopts the 2023 NEC (ICC, Sept 4, 2026).
- Fla. Stat. 553.73(7)(d): the edition in effect on the date of permit application governs.
- 2026 NEC adds 625.4 (qualified person), 625.5 (field markings), 625.44(B) (listed receptacles) and counts EVSE at 100 percent in 120.82(D), per EC&M.
- 625.43(D) emergency shutoff is 20 to 100 feet and applies to other than one- and two-family dwellings (EC&M).
The short version: which code applies to your charger?
The National Electrical Code (NEC, also called NFPA 70) is the model safety code for electrical work. A new edition comes out every three years. States and cities then decide when to start using it. Texas and Florida do this on different dates and in different ways, so the same charger can fall under different editions depending on where you live and when you apply for the permit.
| Question | Texas | Florida |
|---|---|---|
| Newest NEC edition in use | 2026 NEC, effective September 1, 2026 for all non-exempt electrical work | 2023 NEC arrives with the Florida Building Code 9th Edition on December 31, 2026 |
| What applies today | 2026 NEC for work covered by the state rule | 8th Edition (2023) Florida Building Code until December 30, 2026 |
| What decides the edition | State rule, from September 1, 2026, in cities and counties alike | The edition in effect on the date you apply for the permit |
| Can a city go lower? | No. A city may amend but not be less strict than the state NEC | Local rules for EV charging stations are preempted by state law |
| Agency | Texas Department of Licensing and Regulation (TDLR) | Florida Building Commission, local building departments |
Do not read "2023 NEC" as Texas's current code. In Texas the 2023 NEC was replaced on September 1, 2026. In Florida, the 2023 NEC is the newer edition that has not started yet.
This page is general information, not legal advice or an inspection ruling. Your local building department makes the final call on your permit.
When does Texas adopt the 2026 NEC?
On July 28, 2026, the Texas Commission of Licensing and Regulation voted unanimously to adopt the 2026 NEC for Texas, effective September 1, 2026, for all non-exempt electrical work (TDLR bulletin, July 2026). TDLR also moved state electrician exams to the 2026 NEC on September 1.
The rule change is in Title 16, Texas Administrative Code, Chapter 73, section 73.100. TDLR's rulemaking notice says the adoption was published on August 28, 2026 in the Texas Register (51 TexReg 5776) and takes effect September 1, 2026. It includes one limited exception on GFCI protection for certain outdoor outlets, explained below.
Cities and counties
TDLR says that starting September 1, 2026, all non-exempt electrical work in Texas, whether inside a city or out in the county, must be done to the state-adopted 2026 NEC. A city cannot make a state-licensed electrical contractor install something that directly violates or falls below the 2026 NEC.
Occupations Code 1305.201 and 1305.202 let a city amend the state code. They do not let a city adopt its own separate code. TDLR notes that amendments must be at least as strict as the NEC, taking NEC section 90.4 into account. Section 1305.201(e) says electrical work in unincorporated areas must meet standards at least as strict as the state electrical code. That means a house outside any city limits in a Texas county is still covered.
What this means for a charger permit
- The Houston Permitting Center says permit applications submitted on or after September 1, 2026 are reviewed for compliance with the new state minimum 2026 NEC. Houston's Electrical Inspections number is (832) 394-8860.
- Other Texas cities may publish their own notices. See our city pages for Dallas, San Antonio and Austin. Where we could not load a city notice, we say so.
- If your contract was signed before September 1 but the permit is filed after, ask your electrician which edition they are using. The Houston notice speaks of the application date.
Texas law lists who is exempt. Occupations Code 1305.003(a)(6) exempts an owner who lives in a dwelling and does the work, but only if no municipal ordinance specifically regulates the work. Check with the city before you plan to do any of the work yourself. See who can install an EV charger in Texas.
Which NEC does Florida use for EV chargers right now?
Florida does not adopt the NEC alone. It builds the NEC into the Florida Building Code. The 8th Edition (2023) Florida Building Code took effect on December 31, 2023, according to the Florida Building Commission. The 9th Edition (2026) takes effect on December 31, 2026.
The International Code Council reported on September 4, 2026 that Florida will update to the 9th Edition effective December 31, 2026, and that it adopts the 2023 NEC (NFPA 70) together with the 9th Edition fire, mechanical, plumbing, fuel gas, energy conservation, accessibility and residential codes.
What the 8th Edition uses
We could not load the 8th Edition electrical chapter itself, and the Florida Building Commission's own page does not say which NEC it cites. The City of Miami's building page lists "National Electrical Code (NEC) / (NFPA 70) / 2020 Edition" among the applicable state codes. We therefore expect the 8th Edition to use the 2020 NEC, but we have not verified this in the code text. Confirm with your building department before you rely on it.
The vesting rule
Florida Statutes 553.73(7)(d) says the Florida Building Code edition in effect on the date of application for a permit governs. A law firm client alert from November 2026 describes the same rule as holding for the life of the permit and any extension. We cite the statute for the rule and the alert only as a secondary summary.
| Permit application date | Florida code that governs |
|---|---|
| On or before December 30, 2026 | 8th Edition (2023) |
| December 31, 2026 or later | 9th Edition (2026), with the 2023 NEC |
| Miami-Dade online application after 4 PM December 30, 2026 | 9th Edition (2026) |
Miami-Dade's Permitting and Inspection Center says all permit applications and plans submitted on or after December 31, 2026 must comply with the new edition, and online applications after the close of business at 4 PM on December 30, 2026 fall under the 2026 edition. The City of Jacksonville's Building Inspection Division says the code in effect for permits submitted on or after January 1, 2024 is the 8th Edition (2023), with online submission through JaxEPICS.
Florida also has a statute that stops local governments from making their own rules about EV charging stations (Fla. Stat. 366.94). That law still has cities issuing permits for chargers under state standards. Do not tell yourself that Florida cities cannot require permits for a home charger. They can, under the building and electrical codes.
The conflict: Texas 2026 NEC versus Florida 2023 NEC
This is the part that confuses people. Two neighbors across state lines can have different rules. And inside Florida, two neighbors can have different rules depending on a permit date.
- A Texas electrician working after September 1, 2026 must follow the 2026 NEC. They cannot choose the 2023 NEC.
- A Florida electrician applying for a permit before December 31, 2026 follows the 8th Edition code, which we expect pairs with the 2020 NEC. After that date, the 9th Edition with the 2023 NEC applies. We found no announced date for Florida to adopt the 2026 NEC.
- A charger installed under an earlier edition does not need to be rebuilt just because a new edition appears. The new code applies to new permits. If you later alter the circuit, a new permit may bring the new rules into play for the new work. Ask your building department. We did not find an official statement that says existing chargers must be updated, but the law of each jurisdiction controls.
The practical advice is simple. Put the code edition in your written quote. Ask the electrician to state in the quote or contract which edition governs the job.
What changed for EV chargers in the 2026 NEC?
The following list comes from EC&M's "Top 25 Changes to the 2026 NEC." It is a trade press summary, so electricians should confirm the exact wording in NFPA 70-2026 before quoting it.
| Section | What it does | Does it affect a house? |
|---|---|---|
| 625.4 (new) | Permanently installed EV power transfer equipment must be installed by a qualified person, as defined in Article 100. | Yes. Another reason not to treat a hardwired Level 2 install as a casual DIY job. |
| 625.5 (new) | EVSE enclosures must carry permanent field markings that stay visible after installation: supply voltage, phases, frequency, full-load current and short-circuit current rating. | Yes, mostly an electrician and inspector item. Check that the label is present and readable. |
| 625.43(D) (new) | For other than one- and two-family dwellings, permanently connected EVSE needs an emergency shutoff within sight, 20 to 100 feet away, marked "EVSE EMERGENCY DISCONNECT." | No for a typical single-family house or duplex. Yes for apartments, condos and commercial sites. |
| 625.44(B) (new) | Receptacles used for hand-fastened EV charging connections at 30, 50 or 60 amps must be listed for EVSE and wireless power transfer use. | Yes if you use an outlet instead of hardwiring. Ordinary receptacles may not qualify. |
| 120.82(D) (new) | In the dwelling optional load calculation, EVSE counts at 100 percent of its nameplate rating. | Yes. It affects the panel capacity math. |
| Article 120 (relocated) | Load calculation rules moved here from Article 220. | Yes, mostly for electricians. Anyone searching "Article 220" may find old material. |
| 210.8(F) (expanded) | GFCI protection now applies to outdoor outlets rated 60 amps or less (up from 50) in locations including garages and accessory buildings. | Possibly. See the GFCI section below and our GFCI and listing guide. |
What is a qualified person?
Article 100 of the NEC defines the term, and we did not load that definition, so ask your electrician how it applies. In Texas and Florida, the practical effect is that the person must also hold the state or local license that the law requires for the work. See Texas and Florida installer rules.
Emergency shutoff: the number to get right
One summary elsewhere said the shutoff must be 20 to 25 feet away. EC&M says 20 to 100 feet and says the rule applies to equipment other than one- and two-family dwellings. We use the EC&M figures. A typical house garage charger does not need this separate shutoff under that rule.
Note: 2026 NEC section numbers in this guide come from published trade summaries and may be renumbered in the final adopted text. Confirm them in NFPA 70-2026 or with your electrician and local inspector before relying on them.
GFCI and the 2026 NEC: Texas has a specific amendment
A GFCI (ground-fault circuit interrupter) shuts off power fast when current leaks to ground, which protects people from shock. NEC section 210.8 lists places that need it. Section 625.54 covers GFCI protection for personnel specifically for EV charging receptacles.
What Texas changed
The Texas commission approved an amendment to NEC 210.8(F) so that GFCI protection is not required on outdoor dwelling-unit HVAC outlets. The adopted rule says the exception is limited and concerns certain outdoor outlets. TDLR's notice does not say it affects EV charger circuits. Do not extend it to chargers. Section 625.54 is separate.
The proposed fix for 625.54 (TIA 1892)
A Tentative Interim Amendment (TIA) is a mid-cycle change to the NEC. TIA 1892 would revise section 625.54 so GFCI protection for personnel applies to receptacles installed for EV charging equipment and wireless power transfer equipment. The proposal cites nuisance trips and stranded-driver hazards with permanently wired equipment.
Status: unconfirmed. EC&M reported that the TIA passed a ballot, and the NFPA's proposed TIA document is public. A web search also surfaced a Standards Council decision dated August 20, 2026, but we could not read it, and the snippets conflicted about the vote. We therefore do not state TIA 1892 as adopted code. Texas has not said it adopted this TIA. Ask your electrician or inspector whether it applies to your permit.
Does the 2026 NEC require a qualified person for a plug-in charger?
EC&M's summary of 625.4 refers to permanently installed equipment such as Level 2 or higher chargers. A portable charger that plugs into a standard outlet is a different thing. But the outlet circuit itself is electrical work. If the outlet does not exist yet, a licensed electrician needs to add it. See the guide to NEMA outlets and hardwired chargers.
EPA says chargers rated at 48 amps or higher are usually required to be hardwired rather than plugged in.
What about NECA 413?
NECA 413 is a standard for the installation and maintenance of EV charging. DOE's multifamily guide (March 2026) points to NECA 413 as covering safe installation of Level 1, Level 2 and Level 3, system capacity and NEC compliance. It is not a law. Many electricians use it as a practice guide. The NEC and your local rules are what the inspector enforces.
Do I need to redo an older charger when the code changes?
Generally, codes apply to new work and to the permit under which that work was approved. Florida's statute ties the edition to the permit application date, and the edition governs for the life of that permit. We did not find an official Texas or Florida statement that requires owners to update a finished residential charger because a new edition arrived. If you add a second charger, move the circuit or replace the panel, the new permit will use the code edition in force on its date. When in doubt, call the building department and ask. Our inspection checklist can help you prepare.
Insurance and resale
An unpermitted charger can complicate a home sale or an insurance claim. See EV charger insurance.
Counties and unincorporated areas in Texas
Under Occupations Code 1305.201(e), work in unincorporated areas must meet standards at least as stringent as the state electrical code. TDLR's bulletin says the 2026 NEC applies to non-exempt work out in the county. Some Texas counties have no building department, so there may be no county permit to file, but a state-licensed electrician must still install to the 2026 NEC. The utility or retail co-op may also require an inspection. Ask your electric provider.
How to choose a provider
- Find your permit application date: it decides your edition in Florida.
- In Texas, assume the 2026 NEC for any work permitted on or after September 1, 2026.
- Ask your electrician to put the code edition in the written quote.
- Verify the electrician's TDLR or DBPR license.
- If using an outlet, ask for a receptacle listed for EV charging use (2026 NEC 625.44).
- Check that the charger carries a visible field marking label.
- Ask whether GFCI protection is needed on the circuit and where it is located.
- For a Florida job, ask the building department which edition governs and what the Dec. 30, 2026 cutoff means.
- Keep the permit and final inspection approval.
- Do not rely on third-party websites for code text; read it from NFPA, TDLR or your building department.
Related home ev charger installation guides
- GFCI, AFCI, Surge Protection and UL Listing for Home EV Chargers: What Is Required and What to Look For
- EV Charger Load Calculation: How an Electrician Sizes Your Service Under NEC 625 and 220/120
- Do You Need a Permit to Install an EV Charger in Texas? State Rules, Exemptions and the 2026 NEC
- Do You Need a Permit to Install an EV Charger in Florida? Statute 366.94, FBC Editions and Owner-Builder Rules
- Who Can Legally Install an EV Charger in Texas? TDLR Electrician Licenses and How to Verify One
- Who Can Legally Install an EV Charger in Florida? Chapter 489 Licenses and How to Verify One
- EV Charger Inspection: What Inspectors Check in Texas and Florida (and How to Pass the First Time)
- Do You Need a Panel or Service Upgrade for an EV Charger? What It Involves, Permits and Utility Steps
Home EV charger installation by state and city
Questions people ask
When does Texas adopt the 2026 NEC?
September 1, 2026. The Texas Commission of Licensing and Regulation voted on July 28, 2026, and TDLR says the 2026 NEC applies from September 1 to all non-exempt electrical work in Texas, whether inside a city or out in the county. The rule is 16 TAC 73.100, published as 51 TexReg 5776 on August 28, 2026.
Which NEC does Florida use for EV chargers right now?
Florida uses the 8th Edition (2023) Florida Building Code through December 30, 2026. We could not verify in the code text which NEC edition it cites. The City of Miami's building page lists the 2020 NEC among applicable codes. From December 31, 2026, the 9th Edition applies with the 2023 NEC.
Does my permit date decide which code applies?
In Florida, yes. Statute 553.73(7)(d) says the edition in effect on the permit application date governs. Miami-Dade says online applications after 4 PM on December 30, 2026 fall under the 9th Edition. In Texas, Houston says permit applications on or after September 1, 2026 are reviewed against the 2026 NEC.
Does the 2026 NEC require a qualified person to install a charger?
Yes for permanently installed equipment. New section 625.4 requires EV power transfer equipment such as Level 2 or higher chargers to be installed by a qualified person as defined in Article 100, per EC&M. Texas and Florida also require licensed electrical contractors for non-exempt work.
What is the new emergency shutoff rule?
Section 625.43(D) requires an emergency shutoff within sight, 20 to 100 feet from the equipment, for permanently connected EVSE in other than one- and two-family dwellings. It is marked EVSE EMERGENCY DISCONNECT. Typical single-family and duplex home garages are not covered by this rule.
What does the 2026 NEC say about GFCI for EV chargers?
Section 625.54 covers GFCI protection for personnel for EV charging receptacles. TIA 1892 proposes to extend it to receptacles for EVSE and wireless equipment. We could not confirm the TIA's final status. Texas's 210.8(F) exception covers outdoor HVAC outlets only, not chargers. Ask your electrician and inspector.
Why did Article 220 move?
The 2026 NEC moved load calculation rules from Article 220 into new Article 120. For the optional dwelling method, 120.82(D) counts EVSE at 100 percent of its nameplate rating. Older web pages may still cite Article 220 numbers, so check which edition they describe.
Do I need to redo an older charger when the code changes?
We found no official Texas or Florida rule that makes owners redo a finished residential charger because a new code edition arrives. A new permit for new work uses the edition in effect on its application date. Ask your building department if you plan to change the circuit.
Does the code apply in unincorporated Texas counties?
Yes. TDLR says non-exempt electrical work in the county must follow the state-adopted 2026 NEC. Occupations Code 1305.201(e) requires work in unincorporated areas to meet standards at least as stringent as the state code.
What is NECA 413?
NECA 413 is a standard for the installation and maintenance of EV chargers. DOE's multifamily guide (March 2026) points to it for safe installation, system capacity and NEC compliance. It is a practice document, not a law.
Sources
- TDLR bulletin: The Texas Circuit, July 2026
- TDLR rulemaking: Commission adopts rules (16 TAC 73.100)
- Houston Permitting Center: 2026 NEC effective September 1, 2026
- Texas Occupations Code Chapter 1305
- EC&M: Top 25 Changes to the 2026 NEC
- EC&M: TIA proposed for 2026 NEC on GFCI protection for personnel
- NFPA: Proposed TIA 1892 to NFPA 70-2026
- ICC: Florida adopts new building codes
- Miami-Dade Permitting and Inspection Center: FBC 9th Edition notice
- Florida Statutes 553.73
- Florida Building Commission
- City of Jacksonville Building Inspection Division
- City of Miami Building Department
- Florida Statutes 366.94
- Greenberg Traurig: New Florida Building Code edition takes effect Dec. 31, 2026
- DOE Multifamily EV Charging Guide (March 2026)
- EPA: Getting Started with Home EV Charging
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


