New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Fri, Nov 20, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Home EV charger installation

EV Charger Load Calculation: How an Electrician Sizes Your Service Under NEC 625 and 220/120

How an electrician checks whether your home has room for an EV charger: the 125 percent rule, the 2023 methods, the 2026 NEC Article 120 rewrite, worked 100, 150 and 200 amp examples and how load management changes the math.

A load calculation adds up the electricity a home can use at once and checks whether an EV charger fits inside the service size. The charger counts as a continuous load, so its circuit is sized at 125 percent, and under the 2026 NEC optional dwelling method the charger counts at 100 percent of its nameplate with no demand factor. A licensed electrician or engineer performs it.

Key facts

  • DOE says EV charging is a continuous load under the NEC and NEC Article 625 holds most of the rules; the NEC requires wiring and overcurrent protection at 125% of the charger's nameplate continuous output.
  • The 2023 NEC offers two ways to size an existing home: 220.83 (nameplate-based, 100% of the first 8,000 W plus 40% of the rest) and 220.87 (metered peak demand plus a 25% safety factor, with new loads at 100% of nameplate) (national laboratory slides).
  • The 2023 NEC added 220.57, which counts EVSE at the larger of 7.2 kW or its nameplate rating, and 220.70, which lets an energy management system set point be used in a load calculation, limited to 80% of panel rating (national laboratory slides).
  • The 2026 NEC moves load calculations from Article 220 to Article 120 and, for the dwelling unit optional method (120.82(D)), counts EVSE at 100% of nameplate with no demand factor (EC&M).
  • The 2026 NEC limits a power control system's control setting used in load calculations to 80% of the overcurrent device rating (120.7(B)), and energy management rules move to Article 130 (EC&M).
  • Under the 2023 NEC, where an energy management system controls EVSE, the EVSE load is not included when sizing feeders and service conductors (625.42(A), training excerpt).
  • Texas adopted the 2026 NEC effective September 1, 2026; Florida stays on the 8th Edition building code until December 30, 2026, then moves to the 9th Edition, which the ICC says adopts the 2023 NEC.
  • EPA says a home with 200 amps and two open double-pole slots likely has capacity for Level 2, and that an electrician can perform a load calculation to determine whether the panel can handle a charger.

What is an EV charger load calculation?

A load calculation is a worksheet that estimates how much electricity a home could use at one time and compares it to the size of the electrical service. The service size is set by the main breaker, for example 100, 150 or 200 amps at 240 volts. EPA says an electrician can perform a load calculation to determine whether your existing electrical panel can handle an EV charger or whether you need upgrades, and DOE says a load calculation or load study may be required.

The calculation answers one question: after adding this charger, is the total still within the service rating? If yes, the charger can go on a new breaker. If no, the electrician looks at options: a smaller charger, load management, shifting or removing other loads or a service upgrade.

It is not the same as picking the breaker and wire for the charger circuit. Those use the 125 percent continuous-load rule described below. The load calculation looks at the whole house.

Who performs the calculation?

A licensed electrician or an engineer. In Texas, anyone who performs non-exempt electrical work must be licensed and work through a licensed electrical contractor, according to the Texas Department of Licensing and Regulation (TDLR). In Florida, the Department of Business and Professional Regulation (DBPR) licenses electrical contractors and the license can be checked on MyFloridaLicense.com. Read Texas licensing and Florida licensing. Homeowners can use the worksheets in this guide to understand the process, but should not use them to replace a professional's calculation.

Is an EV charger a continuous load, and what does that mean?

Yes. DOE says EV charging infrastructure is considered a continuous load by the National Electrical Code (NEC). In practice that means the code assumes a charger may run for hours at full current, so extra margin is built into the circuit. DOE's March 2026 guide says the NEC requires wiring size and overcurrent protection of 125 percent of the charger's nameplate continuous output rating.

A training excerpt of the 2023 NEC gives the sections:

  • 625.41: Overcurrent protection must be at least 125 percent of the EVSE current rating (a 40 amp charger needs a 50 amp breaker).
  • 625.42: EVSE is a continuous load, and the conductor must have at least 125 percent ampacity.
  • 625.40: EVSE rated over 16 amps or 120 volts needs its own branch circuit, with an exception for loads managed by an energy management system.

That is the circuit rule. The service rule is different, because the service load calculation uses methods in Article 220 (2023 NEC) or Article 120 (2026 NEC) that apply their own factors. Do not mix the two. The 125 percent number belongs to the branch circuit. The load calculation counts the charger at a different percentage depending on the method and edition, as the next sections show.

Which NEC edition applies in Texas and Florida?

The answer changes the numbers and even the section numbers, so check it first.

PlaceRuleWhere the load calculation lives
Texas, work on or after September 1, 2026The Texas Commission of Licensing and Regulation adopted the 2026 NEC effective September 1, 2026, for non-exempt electrical work (TDLR). Cities may amend only to be at least as stringent. Houston says permits filed on or after that date are reviewed against it.Article 120 (2026 NEC)
Florida, permit applications through December 30, 2026Florida Building Code, 8th Edition (2023). Which NEC edition it references is not confirmed in our sources.Likely Article 220 if the 8th Edition uses the 2020 or 2023 NEC; confirm with the building department
Florida, applications on or after December 31, 20269th Edition (2026), which the ICC says adopts the 2023 NEC. The edition in effect on the application date governs the permit.Article 220 (2023 NEC)

So in 2026 a Houston calculation uses Article 120, while a Miami calculation may still use Article 220. The same house in two cities could be run under different section numbers and slightly different rules. A good electrician will state the edition used on the permit. See 2026 NEC changes for Texas and Florida.

The 2023 methods: 220.83 and 220.87 for an existing home

A set of slides from Lawrence Berkeley National Laboratory summarizes the two main methods for adding a load to an existing house under the 2023 NEC. We use that summary here. The NEC text itself is the authority.

220.83: the nameplate method (optional calculation for existing dwellings)

  • It estimates load from the nameplate ratings of the installed appliances.
  • With no new air-conditioning or heating, the slides say it uses 100 percent of the first 8,000 watts plus 40 percent of the remaining loads (including HVAC).
  • With new HVAC, it adds the larger of heating or cooling.
  • It gives a larger existing load but allows more new load.
  • It suits adding lots of new loads, or cases where metering data cannot be used.
  • It requires an inspection of the home and a record of the nameplate values.

220.87: the metering method (determining existing loads)

  • It estimates load from metering data plus a 25 percent safety factor.
  • New loads are added at 100 percent of their nameplate rating.
  • It gives a smaller existing load but allows less new load.
  • It suits adding one or two loads, or adding loads over time.
  • The slides say the 2023 revision lets homes with solar or demand response use the method when at least one year of data is available.

We did not load the NEC text for the length or timing of the recorded demand data, so ask the electrician exactly what record they will use and who supplies it. Some Texas and Florida utilities provide interval (smart meter) data to customers, but we did not verify any utility's process.

The 2023 additions for EV chargers

The same slides list two new items in the 2023 NEC: Section 220.57 for EVSE load, which says to use the larger of 7.2 kW and the nameplate rating, and Section 220.70, which allows an energy management system's current set point to be used in load calculations, limited to 80 percent of the panel rating. Section 625.42 was revised to allow EVSE ratings based on the use of an energy management system or on EVSE with adjustable settings.

The 2026 NEC: Article 120 and the EVSE at 100 percent rule

EC&M's summary of the 2026 NEC says the NEC moved load calculations into a new Article 120, because load calculations apply to all installations. Article 120 "contains the requirements necessary for calculating demand loads for branch circuits, feeders, and services." Energy management system rules moved from Article 750 to a new Article 130. EC&M lists these EV-relevant load changes:

  • 120.82(D), EVSE load at 100 percent. For the dwelling unit optional method, the EVSE load must be calculated at 100 percent of its nameplate rating with no demand factor "because it represents a significant load."
  • 120.82(B), general loads. The demand load for the optional method changed from 100 percent of the first 10 kVA to the first 8 kVA, plus 40 percent of the remainder. The general lighting and receptacle load was reduced from 3 VA to 2 VA per square foot.
  • 120.7, power control systems. A listed power control system may be used in load calculations with a control setting not exceeding 80 percent of the overcurrent protective device rating. The calculation sums controlled loads (using the control setting or the minimum operating current) and noncontrolled loads.

The "no demand factor" language matters. A demand factor lets some loads count at less than 100 percent because not everything runs at once. The 2026 NEC says an EV charger does not get that discount in the optional dwelling method. Plan on it counting in full. Other summaries say the existing-dwelling methods (120.83 and 120.87) were also moved to Article 120. We did not confirm that from the NEC text, so ask your electrician which section they cite.

Also new in Article 625: the 2026 NEC adds Section 625.4 (permanently installed EV equipment must be installed by a qualified person) and Section 625.5 (field markings of full-load current on the EVSE enclosure). The markings make the load on the permit match the charger setting. See how many amps.

How do I calculate my home's service capacity in amps?

Start with what you can read yourself. EPA says you can often find your home's electrical service capacity by checking the main switch at the top of your primary panel. The number on that breaker is the total amps your home can provide. Do not open the panel cover. CPSC's wiring guide says to leave the service-panel cover to a qualified electrician.

Convert amps to watts by multiplying by 240 volts. We show the results in the table. The result is the ceiling for the sum of your loads.

Main breakerService capacity at 240 V
100 A24,000 W (24 kW)
150 A36,000 W (36 kW)
200 A48,000 W (48 kW)

Typical load sizes for new equipment from the national laboratory slides: EV charger 3 to 12 kW, resistance heating 5 to 20 kW, cooking 6 to 13 kW, heat pump HVAC 3 to 10 kW, clothes dryer 4 to 6 kW, water heater 4.5 kW. Use these ranges only to see which items are heavy. The real numbers come from nameplates.

Next, a trained person adds the existing load by one of the methods above and adds the charger. The remaining sections show two simplified examples.

Worked example 1: the metering method (illustrative)

This example follows the national laboratory's picture of the metering method. The slides show a 100 amp, 24 kW service with a measured peak of 4,000 watts. Multiplied by 1.25, the home counts as using 5,000 watts, which leaves 19,000 watts for the full nameplates of new equipment. That is the slides' own example.

Texas and Florida homes usually have central air conditioning, and the peak in July or August is higher than the peak in April. Because the metering method depends on the measured peak, a spring reading could badly understate the summer load. Ask what period the electrician is using and whether it includes the hottest weeks. Below is a made-up summer case (our illustration, not a real home).

Item100 A (24,000 W)150 A (36,000 W)200 A (48,000 W)
Measured summer peak (illustrative)11,000 W11,000 W11,000 W
Peak x 1.2513,750 W13,750 W13,750 W
Capacity left for new nameplates10,250 W22,250 W34,250 W
24 A charger (5,760 W)FitsFitsFits
32 A charger (7,680 W)FitsFitsFits
40 A charger (9,600 W)Fits, 650 W to spareFitsFits
48 A charger (11,520 W)Does not fitFitsFits

In this illustration a 100 amp home could take a 40 amp charger but not a 48 amp one, with very little room left for adding a heat pump or another EV. The same home could take a 24 or 32 amp charger with more margin. Change the measured peak and the answer changes. This is why real calculations use real data.

Worked example 2: the nameplate method (illustrative)

The national laboratory slides include a worked 220.83-style example for a 2,000 square foot home with a 100 amp service. It totals 15,432 watts (about 65 amps at 240 volts) for the appliances plus heating and cooling and a heat pump water heater. We use that 15,432 watt result as the starting load, then add each charger at 100 percent of its nameplate, which is the 2026 NEC approach for the optional dwelling method. This is a simplified illustration. A real calculation applies the exact factors of the edition and method in use.

Charger addedCharger loadNew totalNew total in amps at 240 VFits on 100 A?Fits on 150 A?
None0 W15,432 W64.3 AYesYes
24 A5,760 W21,192 W88.3 AYesYes
32 A7,680 W23,112 W96.3 AYes, little marginYes
40 A9,600 W25,032 W104.3 ANoYes
48 A11,520 W26,952 W112.3 ANoYes

The slides state 65 amps as the rounded result. We show 64.3 amps from 15,432 watts divided by 240 volts. In this example a 40 or 48 amp charger overloads the 100 amp calculation, even though the charger is "only" 40 percent of the service when measured by itself. A 24 or 32 amp charger fits. The same house with a 150 amp or 200 amp service has room for any of them. These are the kinds of results that lead to the options in the next section.

What if the calculation shows I am over capacity?

You have options, in rough order of cost. DOE's March 2026 guide lists capacity strategies from least to most costly: low-power chargers (25 to 50 percent less power than Level 2), then meter collars, circuit splitters, smart breakers or energy management hardware that pause or reduce charging when the draw could exceed limits, then circuit sharing and automated load management, and, if you are replacing the panel anyway, a smart panel.

  1. Choose a lower-amp charger. A 24 or 32 amp charger fits in the examples above where a 40 amp one did not. EPA suggests a 16 amp Level 2 charger as an option if your panel is tight.
  2. Use load management. A listed energy management system can limit the charger so the total never exceeds the limit. Under the 2023 NEC, where an energy management system controls the EVSE, the load is not included when sizing feeders and service conductors (625.42(A) in the training excerpt). The 2026 NEC allows a power control system's control setting in calculations, capped at 80 percent of the overcurrent device rating. See load management and smart panels.
  3. Change other loads. Replace or schedule a large load, or choose a heat pump water heater instead of electric resistance, for example. The national laboratory slides list "circuit sharing devices" such as alternating a dryer and an EV charger, and "circuit pausing" devices, as low-power electrification strategies.
  4. Upgrade the panel or service. DOE notes that a panel upgrade may trigger an upgrade to the utility service. See panel and service upgrade for an EV charger.

Does a smart charger or load management change the calculation?

It can, but only if the equipment qualifies. A smart charger that merely has an app and a timer does not change the code load. The load calculation can change when a listed energy management system or power control system enforces the limit. The 2023 NEC revised 750 to add a listing requirement and tamper protection (national laboratory slides, citing 750.60 and 750.30). The 2026 NEC relocates these to Article 130. EC&M says power control systems add the ability to monitor and control loads to prevent overloading of conductors or equipment.

That means the permit file should list the device, its listing and its set point. The 2026 NEC's field-marking rule (625.5) requires the EVSE enclosure to show full-load current, which matters when current is adjustable. An inspector can then match the nameplate, the set point and the calculation.

What goes on the permit application, and who requires a calculation?

Requirements differ by city and we did not load any Texas or Florida city's form, so we cannot say which ones require a written calculation. DOE says in many areas a site installation plan must be submitted for approval before installation. A typical submission for a residential charger includes the service size, a list of loads or the method used, the charger rating and circuit, and the panel location, but only your city can tell you its checklist. What we could verify about local processes:

  • Houston: The Houston Permitting Center says applications on or after September 1, 2026 are reviewed against the 2026 NEC, and lists Electrical Inspections at (832) 394-8860.
  • Dallas: The city takes permit submittals through the DallasNow portal.
  • Jacksonville: Permits are submitted online through JaxEPICS; the Building Inspection Division is at 904-255-8500.
  • Tampa: Construction Services uses Accela Citizen Access and can be reached at (813) 274-3100 option 1.
  • Orlando: Offers online permit lookup, digital plan review and inspection scheduling.

See each city's permit guide: Houston, Dallas, San Antonio, Austin, Miami, Tampa, Orlando, Jacksonville. Ask the electrician to give you a copy of the calculation they used.

Does adding a charger affect homeowners insurance?

We did not load an insurance source for this guide. Call your insurer or agent and ask whether they want to know about a new circuit or charger, and keep the permit and inspection record. See EV charger insurance.

Terms in plain English

  • Demand factor: A percentage used to count a load at less than 100 percent because not all loads run at once. The 2026 NEC says EVSE gets none in the optional dwelling method.
  • Continuous load: A load expected to run for hours. The NEC uses 125 percent for sizing the circuit.
  • Nameplate: The label on equipment showing its rated volts, amps or watts.
  • Optional method: A shorter NEC calculation that the code allows for dwellings.
  • Energy management system (EMS): Equipment that controls loads. A power control system (PCS) is an EMS that also protects against overload.
  • VA and kVA: Volt-amperes, almost the same as watts for home loads. 1 kVA is 1,000 VA.

How to choose a provider

  • Read the amps on your main breaker without opening the panel cover.
  • Ask the electrician which NEC edition and method they will use and have them state it on the permit.
  • Ask for a copy of the load calculation and the nameplate values used.
  • If the calculation uses metering data, ask which months the data covers and whether it includes summer.
  • Plan for the charger to count at 100 percent of nameplate with no demand factor in the 2026 NEC optional method.
  • If the result is tight, ask about a lower-amp setting or charger before an upgrade.
  • If you use load management, confirm the device is listed and that its set point is documented.
  • Check your city's permit checklist and portal before the work starts.
  • Keep the calculation, permit and final inspection records with your home files.

Related home ev charger installation guides

Home EV charger installation by state and city

Questions people ask

What is a load calculation for an EV charger?

It is a worksheet that adds up the electricity a home can use at once and checks that it stays within the service size after the charger is added. EPA says an electrician can perform one to determine whether your panel can handle a charger. DOE says a load calculation or load study may be required.

Who performs an electrical load calculation?

A licensed electrician or engineer. In Texas, TDLR says anyone who performs non-exempt electrical work must be licensed and work through a licensed electrical contractor. In Florida, electrical contractors are licensed through DBPR, and you can check a license on MyFloridaLicense.com. Ask for a copy of the calculation for your records.

What is NEC 220.83 and how does it apply to EV chargers?

It is the 2023 optional method for existing homes. A national laboratory summary says it counts 100 percent of the first 8,000 watts plus 40 percent of the remainder, adds nameplate loads and requires a home inspection. An EV charger is added as a new load. The 2026 NEC moves load calculations to Article 120.

What is the 2026 NEC rule for EVSE load in the optional method?

Section 120.82(D) says to use 100 percent of the EVSE nameplate rating, with no demand factor, according to EC&M's summary. Load calculations moved from Article 220 to Article 120. Texas adopted the 2026 NEC effective September 1, 2026. Confirm the exact text in NFPA 70-2026 with your electrician.

Is an EV charger a continuous load?

Yes. DOE says the NEC considers EV charging a continuous load. For the circuit, that means a breaker and wire at least 125 percent of the charger's rating, so a 40 amp charger needs a 50 amp circuit. For the service load calculation, the charger counts at its nameplate under the 2026 optional method.

Can I use my utility bill instead of a calculation (220.87)?

Section 220.87 uses metered peak demand, not a bill total, plus a 25 percent safety factor, per a national laboratory summary. An electrician must decide whether the data you have qualifies. Texas and Florida summer peaks are higher than spring, so the period matters. Ask what data the inspector accepts.

What happens if the calculation shows I am over capacity?

Options include a lower-amp charger, a listed load management system, shifting other loads or upgrading the panel or service. DOE lists low-power chargers, meter collars and smart breakers, then circuit sharing, as increasingly costly strategies. A service upgrade may need utility work that can take months.

Does a smart charger or load management change the calculation?

Only a listed energy management or power control system can. Under the 2023 NEC, EMS-controlled EVSE is not included in feeder and service sizing (625.42(A)). The 2026 NEC lets a control setting up to 80 percent of the overcurrent device rating be used. An app or timer alone does not change the code load.

What does an electrician put on a permit application for the calculation?

It varies by city, and we did not load any city's form. DOE says many areas require a site installation plan before installation. Expect the service size, loads or method used, charger rating, circuit details and panel information. Check your city portal, for example Houston, DallasNow, JaxEPICS or Accela.

Does adding a charger affect my homeowners insurance?

We did not load an insurance source. Ask your insurer or agent whether they want notice of a new circuit or charger. A permitted, inspected installation by a licensed contractor gives you the paper record to share. See the EV charger insurance guide in this series for more.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration