Local Guide · Plumbing
What Plumbing Rules Apply to Small Businesses? Commercial Plumbing for Restaurants, Offices, Salons and Retail
A plain-English guide for small business owners and commercial landlords in Texas and Florida: restroom counts, ADA fixtures, restaurant plan review, backflow testing, NNN lease clauses, buildouts and maintenance contracts.
Commercial plumbing must meet code minimums that homes do not: fixture counts by occupancy (for example, Florida's 2023 code requires restaurant toilets at 1 per 75 occupants for each sex plus a service sink), ADA 2010 accessible restrooms, testable backflow assemblies tested at least annually, and, for food service, health department plan review. Who pays for repairs depends on your lease, not state law. Use licensed contractors and plan plumbing before signing a lease.
Key facts
- Florida's plumbing code requires restaurant water closets at 1 per 75 occupants for each sex, lavatories at 1 per 200, and a service sink (FBC Plumbing 2023, Table 403.1).
- Separate restrooms are not required in tenant spaces with a total occupant load of 15 or fewer (FBC Plumbing 2023, 403.2).
- Required toilet facilities must be within 500 feet and one story of the space served (FBC Plumbing 2023, 403.3.3).
- ADA 2010 Standards set toilet seat height at 17 to 19 inches and lavatory height at 34 inches maximum.
- Texas projects with an estimated construction cost of at least $50,000 must submit plans to TDLR for accessibility review (Tex. Gov. Code 469.101).
- Florida DBPR requires plan review for food service establishments that are new, converted, remodeled, or reopening after 18 months closed.
- Florida backflow assemblies at non-residential connections must be tested at least annually (Fla. Admin. Code 62-555.360).
- Texas nonresidential repair and remodeling is taxable on the full charge, labor included (Texas Comptroller).
What's the difference between commercial and residential plumbing?
The pipes and principles are the same, but commercial plumbing answers to more rules, serves more people, and costs more when it fails. For a small business owner in Texas or Florida, the differences that matter most are:
| Issue | Home | Business |
|---|---|---|
| Who may do the work | Homeowner on own homestead (TX) or as owner-builder (FL); otherwise licensed plumber | Licensed plumbing contractor. In Texas, a Tradesman Plumber-Limited may work on buildings other than one- and two-family homes only under direct on-site supervision of a Journeyman or Master |
| Number of fixtures | Whatever the owner wants | Minimum restroom, drinking fountain and service sink counts set by the plumbing code based on occupancy |
| Accessibility | Generally not required in private homes | ADA 2010 Standards apply to public accommodations and commercial facilities; Texas Accessibility Standards and the Florida Building Code, Accessibility add state rules |
| Backflow protection | Basic devices; residential assemblies tested less often | Testable assemblies common; in Texas, assemblies protecting against health hazards must be tested at least annually; in Florida, assemblies at non-residential service connections at least annually |
| Grease, lint and chemicals | Rarely regulated | Restaurants need grease management; salons, labs and laundries may need special treatment under local rules |
| Health department | Not involved | Food service plan review: Florida DBPR Division of Hotels and Restaurants; Texas DSHS or the local health department |
| Sales tax on repairs | Texas residential repair labor not taxable | Texas nonresidential repair and remodeling taxable on the full charge |
| Downtime cost | Inconvenience | Lost sales, closure by health inspectors, tenant claims |
Who pays for plumbing repairs in a commercial lease (NNN)?
In a commercial lease, the lease decides. There is no Texas or Florida statute that assigns commercial plumbing repairs the way residential landlord-tenant laws do. Many small business leases are triple net (NNN), meaning the tenant pays a share of property taxes, insurance and maintenance on top of base rent, and often handles repairs inside its own space. But "NNN" is a label, not a rule; the actual clauses control.
Clauses to read before you sign
- Repair vs replacement. Does the tenant only repair fixtures, or also replace the water heater, grease interceptor or sewer lateral when they fail?
- Where the tenant's responsibility ends. Inside the walls of the suite? To the point of connection with the building's main lines? To the street? A sewer line under the slab of a strip center can serve several tenants.
- Capital items. Who pays for a new water heater, a repiped restroom, or a backflow assembly the utility now requires? Some leases cap tenant contributions to capital repairs or amortize them over their useful life.
- Code-required upgrades. Who pays if your new use triggers more restrooms, accessibility upgrades or a grease interceptor? This is the most common surprise in restaurant leases.
- Backflow testing and grease pumping. Who schedules and pays for annual tests and interceptor service, and who gets the reports?
- Emergency access and response. Who can call a plumber after hours, and who pays if a leak from the unit above floods yours?
- Insurance and waiver of subrogation. Whose property insurance pays for water damage, and does the lease waive claims between landlord and tenant?
- Condition at move-in. Ask for a plumbing inspection, including a sewer camera inspection for restaurants and older buildings, and attach the findings to the lease.
This is general information, not legal advice. Have a commercial real estate attorney review the lease, especially for restaurants, medical and dental offices, salons and other water-heavy uses.
How many restrooms does my business need by code?
Minimum fixture counts come from the plumbing code your jurisdiction uses. Florida uses the statewide Florida Building Code, Plumbing (8th Edition, 2023, based on the 2021 International Plumbing Code). Its Table 403.1 sets minimums by occupancy. Selected rows:
| Occupancy | Water closets | Lavatories | Drinking fountains | Other |
|---|---|---|---|---|
| Restaurants, banquet halls, food courts (Assembly) | 1 per 75 for each sex | 1 per 200 | 1 per 500 | 1 service sink |
| Business (offices, banks, professional services, ambulatory care) | Male: 1 per 25 for the first 50 and 1 per 50 above 50. Female: 1 per 40 for the first 80 and 1 per 80 above 80 | See table | 1 per 100 | 1 service sink |
| Mercantile (retail stores, shops, markets, shopping centers) | Male: 1 per 500. Female: 1 per 750 | See table | 1 per 1,000 | 1 service sink |
Read from the Florida Building Code, Plumbing 2023 as published by UpCodes; the extracted table merged some lavatory columns, so check the official table before relying on a single cell. Counts are based on the occupant load calculated under the building code, not on your actual staff and customer numbers.
When one restroom is enough
Florida's Section 403.2 exceptions say separate men's and women's facilities are not required in:
- structures or tenant spaces with a total occupant load of 15 or fewer;
- mercantile occupancies with a maximum occupant load of 100 or fewer; and
- business occupancies with a maximum occupant load of 25 or fewer.
Restrooms must also be reasonably close. Required public and employee toilet facilities must be within one story of the space they serve, with a path of travel no more than 500 feet (Section 403.3.3 for non-mall buildings).
Texas
Texas cities choose their own code. Dallas and San Antonio use the International Plumbing Code (2021 and 2024 editions, with local amendments), whose fixture tables are similar to Florida's base model. Houston and Austin use the Uniform Plumbing Code (2021 with Houston amendments, and 2024), which has its own fixture table with different numbers. Ask your architect or the city's plan reviewer which table applies. In Florida, food service establishments must also provide at least one public bathroom, with listed exceptions, and the public may not reach it through food preparation, storage or warewashing areas, according to DBPR's plan review guidance.
Do I need ADA-compliant restrooms and fixtures?
If your business is open to the public or is a commercial facility, the federal 2010 ADA Standards for Accessible Design generally apply to new construction and alterations, alongside state rules: the 2012 Texas Accessibility Standards (TAS), administered by the Texas Department of Licensing and Regulation and effective March 15, 2012, and the Florida Building Code, Accessibility. Key plumbing-related dimensions from the 2010 ADA Standards:
| Element | Requirement | Section |
|---|---|---|
| Turning space in the room | 60-inch diameter circle minimum (or permitted T-shaped space) | 603.2.1, 304.3.1 |
| Toilet centerline | 16 to 18 inches from the side wall or partition | 604.2 |
| Clearance around toilet | 60 inches minimum measured from the side wall and 56 inches minimum from the rear wall | 604.3.1 |
| Toilet seat height | 17 to 19 inches to the top of the seat | 604.4 |
| Grab bars | 33 to 36 inches above the floor to the top of the gripping surface | 609.4 |
| Urinal rim | 17 inches maximum above the floor | 605.2 |
| Lavatory or counter height | 34 inches maximum to the front of the rim or counter | 606.3 |
| Pipes under lavatories and sinks | Insulated or configured to protect against contact | 606.5 |
| Knee clearance | 30 inches wide minimum | 306.3.5 |
| Door clear width | 32 inches minimum | 404.2.3 |
Texas registration and review. Under Texas Government Code 469.101, design plans and specifications for new construction or major renovation of a covered building must be submitted to TDLR for review if the estimated construction cost is at least $50,000, and permit officials may not accept a building permit application unless the project has been registered with TDLR as the rules require (469.102). Projects are registered through TDLR's online TABS system; ask TDLR or your architect about the plan review and inspection steps for your project.
Accessibility law is complex, and the obligations of existing businesses (barrier removal) differ from new construction. Work with an architect or accessibility specialist.
What plumbing does a restaurant buildout require?
Restaurant plumbing is where most small business buildout budgets break. Plan for these items:
Florida: DBPR Division of Hotels and Restaurants plan review
DBPR says the law requires it to review establishment plans for sanitation and safety. Plan review is required for food service establishments that are newly built, converted from another use, remodeled, or reopened after being closed at least 18 months. Online applications can expect review within 30 days; you submit the application, a scale floor plan with equipment labeled, and a sample menu. Plumbing items DBPR lists include:
- Handwash sinks: a separate sink used only for handwashing in each food preparation area, and in warewashing and food dispensing areas, with hot and cold running water under pressure, soap, a hand-drying device and a handwash sign.
- Warewashing: a three-compartment sink or commercial dishmachine to wash, rinse and sanitize; drainboards or equivalent at both ends (vented shelving may substitute); dishmachines that automatically dispense detergent and sanitizer, and an alarm on chemical sanitizing machines.
- Mop or utility sink: required, with hot and cold water and connected to a sanitary sewer; it may not be used for warewashing.
- Backflow: all faucets with hose fittings must have a backflow prevention device.
- Drainage: non-sewage liquids must drain per the local plumbing authority, and food contact surfaces may not sit under exposed sewer lines.
- Restrooms: at least one public bathroom (with listed exceptions), no public access through food prep, storage or warewashing areas, vented employee restrooms, and fixture numbers per the local building authority.
Questions about specifics DBPR's page does not cover, such as sink compartment size, water heater capacity or air gaps, go to its plan review team (dhr.planreview@myfloridalicense.com) or your local building and plumbing official.
Texas: DSHS or your local health department
Texas restaurants are licensed and inspected by either the Texas Department of State Health Services or a local health department, depending on location; DSHS publishes a jurisdiction map to find yours. Houston, Dallas, San Antonio and Austin each run their own food establishment permitting and plan review. Ask for their plan review checklist before you finalize the kitchen layout.
Common buildout plumbing items
- Grease interceptor sized and located per the local utility and plumbing code; see grease traps for restaurants.
- Indirect waste connections for ice machines, dishwashers and prep sinks, as the local code requires.
- Water heater sized for peak dishwashing and handwashing demand.
- Floor drains and floor sinks.
- Gas piping for cooking equipment, with permits and pressure tests.
- Backflow protection on carbonation systems, chemical dispensers and other cross-connections.
- Fixture counts and accessible restrooms based on your seating occupant load.
Do salons need special drains or backflow?
Salons, barbershops and spas use a lot of hot water and chemicals, so local plumbing officials and utilities pay attention to two things:
- Backflow. Chemical dispensers, hose-type sprayers and mixing stations connected to the water supply are potential cross-connections. In Florida, backflow assemblies required at non-residential service connections must be tested after installation or repair and at least annually (Fla. Admin. Code 62-555.360). In Texas, TCEQ rules require assemblies to be tested on installation by a licensed tester and, where they protect against health hazards, at least annually (30 TAC 290.44). Your water utility decides what device your service needs.
- Drain capacity and hair. Shampoo bowls clog easily. Ask your plumber about hair interceptors or strainers, cleanouts that are easy to reach, and properly sized drain lines. Local codes and utilities may have specific requirements for some salon and spa wastewater; check before you build.
Also plan water heater capacity for back-to-back shampoo stations, and in older strip centers, ask for a camera inspection of the shared sewer line.
What is a mop sink, and do I need a three-compartment sink?
A mop sink (service or utility sink) is a low, floor-mounted or deep sink for filling and dumping mop buckets. Florida's fixture table lists 1 service sink as a minimum for restaurants, businesses and mercantile occupancies. For food service in Florida, DBPR also requires a utility or custodial sink (or a can wash) for cleaning mops, with hot and cold water and a sanitary sewer connection, and bars using it for dishwashing.
A three-compartment sink is the classic manual warewashing setup: wash, rinse, sanitize. Florida's DBPR allows either a three-compartment sink or a commercial dishmachine, with drainboards at both ends. Many restaurants install both: a dishmachine for volume and a three-compartment sink for pots and backup. Texas health departments apply similar warewashing requirements; confirm with your local health authority.
Backflow testing for commercial properties
| Rule | Texas | Florida |
|---|---|---|
| Testing frequency | On installation by a licensed tester; health-hazard assemblies at least annually (30 TAC 290.44) | Non-residential service connections: after install or repair and at least annually; residential at least every two years (62-555.360) |
| Who tests | Licensed backflow prevention assembly tester (TCEQ license) | As required by the local utility's cross-connection program |
| Other checks | Customer service inspection before continuous service to new construction, when cross-connections are suspected, or after material plumbing changes (30 TAC 290.46(j)) | Dual check devices replaced or refurbished every 5 to 10 years unless the utility documents otherwise |
Missed tests can lead to utility notices and, ultimately, water shutoff. Put test dates on the same calendar as fire sprinkler and grease interceptor service. See backflow prevention and testing.
How do I plan plumbing for a tenant improvement?
- Before you sign the lease: have a plumber or engineer check the existing water service size, sewer line (camera inspection), water heater, restroom count and accessibility, and whether a grease interceptor exists or can be added.
- Confirm the use and occupancy with the building department. Jacksonville's building division, for example, advises prospective tenants and buyers to confirm that their intended use matches the building and fire code classification before leasing, because zoning approval alone does not settle it.
- Hire design professionals for anything beyond simple fixture swaps; commercial permits usually require stamped plans.
- Register accessibility review in Texas if the estimated construction cost is at least $50,000 (Gov. Code 469.101).
- Submit food service plan review to DBPR (Florida) or your Texas health authority before construction.
- Pull permits through a licensed contractor; in Texas, the company's Responsible Master Plumber is responsible for permits and inspections.
- Schedule inspections for underground, rough-in and final, plus health and accessibility inspections.
- Close out: get as-built drawings, warranties, backflow test reports and the certificate of occupancy before opening.
Budget tip: in Texas, repair and remodeling of nonresidential property is generally taxable on the full charge, labor included, unlike residential work, so include sales tax in your buildout budget (Texas Comptroller Publication 94-116).
What is a commercial plumbing maintenance contract?
A maintenance agreement is a contract for scheduled service, often with priority response and set rates. A good one spells out:
- the scope: drain jetting schedule, water heater flushing and inspection, backflow testing, flush valve and faucet rebuilds, grease interceptor service (if included), and leak checks;
- response times for emergencies and after-hours rates;
- pricing: what is included in the fee, the labor rate and parts markup for extra work, and how price changes are handled;
- reports: written service records, test certificates and photos you can hand to your landlord, utility or health inspector;
- licensing and insurance: proof of the company's license (RMP in Texas; CF or RF in Florida) and certificates of insurance naming you or your landlord as required by your lease;
- term and cancellation, including auto-renewal terms.
In Texas, scheduled and periodic maintenance of nonresidential property has its own sales tax treatment distinct from repair and remodeling; ask the vendor how it bills tax (Comptroller Publication 96-259).
Emergency plumbing protocols for a business
- Know your shutoffs. Label the main water shutoff, the suite shutoff (if separate), the water heater valves and the gas shutoff. Show every manager.
- Keep a contact sheet posted: your plumber, the landlord or property manager, the water utility, the gas utility, and your insurance agent.
- For gas odors, evacuate and call the gas utility and 911 from outside. Do not operate switches.
- For sewage backups in a food business, stop food service in affected areas and call your health department as required; contamination is a closure risk.
- Document damage with photos and video before cleanup, and notify your insurer and landlord in writing.
- Keep a spill kit and wet vac on site for small leaks.
- After the event, get a written report from the plumber on cause and repair; your insurer and landlord will ask.
Prevention: annual drain cleaning on high-use lines, grease interceptor service, water heater checks, and leak sensors in back rooms and above-ceiling spaces. See what to do when a pipe bursts and sewer backups.
Hiring a commercial plumber in Texas or Florida
- Texas: verify the company's Responsible Master Plumber in TSBPE's license search and confirm insurance on file. On commercial jobs, apprentices and Tradesmen must work under direct supervision of a Journeyman or Master on site. Medical gas work requires the Medical Gas Piping Installation endorsement.
- Florida: verify the plumbing contractor license (CF or RF) at myfloridalicense.com, confirm a registered contractor is licensed in your jurisdiction, and ask for liability and workers' compensation certificates.
- Both: ask for commercial references in your type of business, get a written scope and schedule, and confirm who pulls permits and schedules inspections. For bigger buildouts, ask about lien waivers at each payment; see plumbing liens.
How to choose a provider
- Before signing a lease, get a plumbing inspection and sewer camera inspection.
- Read the lease's repair, replacement, capital item and code-compliance clauses.
- Confirm your intended use and occupancy classification with the building department.
- Have a designer calculate occupant load and required fixtures.
- Plan accessible restrooms to the 2010 ADA Standards and TAS or FBC Accessibility.
- Texas: register projects of $50,000 or more with TDLR for accessibility review.
- Restaurants: submit health plan review (DBPR in Florida; DSHS or local health department in Texas).
- Size the grease interceptor and water heater for peak use.
- Hire a licensed plumbing contractor and confirm who pulls permits.
- Schedule annual backflow tests and grease interceptor service.
- Post shutoff locations and emergency contacts for all managers.
- Keep as-builts, test reports and warranties on file.
Related plumbing guides
- Does My Restaurant Need a Grease Trap? Rules, Pumping, the 25% Rule and Fines in Texas and Florida
- Do You Need Annual Backflow Testing in Texas or Florida? Rules, Costs and Who Can Test
- How Do You Start a Plumbing Business in Texas or Florida? Licensing, Insurance and Operations
- Should I Get a Sewer Camera Inspection Before Buying a House, and How Do I Read the Report?
- How Do You Hire a Plumber in Texas or Florida and Check the License?
- Can a Plumber Put a Lien on Your Home? Mechanic's Liens in Texas and Florida
- Does Homeowners Insurance Cover Plumbing Leaks? Sudden vs Gradual Damage in Texas and Florida
Plumbing by state and city
Questions people ask
What's the difference between commercial and residential plumbing?
Commercial plumbing serves more people and is governed by more rules: minimum fixture counts by occupancy, accessibility standards, testable backflow assemblies, grease management for restaurants, and health department plan review for food service. Licensing also differs; in Texas, a Tradesman Plumber-Limited may work on commercial buildings only under direct supervision of a Journeyman or Master. In Texas, commercial repair work is also subject to sales tax.
Who pays for plumbing repairs in a commercial lease?
Whatever the lease says. In many triple net (NNN) leases the tenant handles repairs inside its space, but responsibility for replacing water heaters, sewer laterals, grease interceptors and code-required upgrades varies widely. Read the repair, replacement, capital item and compliance clauses, and have a commercial real estate attorney review the lease before signing.
How many restrooms does a small restaurant need?
Under Florida's 2023 plumbing code table, restaurants need water closets at 1 per 75 occupants for each sex, lavatories at 1 per 200, a drinking fountain per 500, and a service sink. Tenant spaces with a total occupant load of 15 or fewer may have a single restroom. Occupant load is calculated from the floor plan, not head counts. Texas UPC cities use a different table; check with your city.
Do I need ADA-compliant restrooms?
If your business serves the public or is a commercial facility, new construction and alterations generally must meet the 2010 ADA Standards plus Texas Accessibility Standards or the Florida Building Code, Accessibility. Key specs include toilet seat height of 17 to 19 inches, lavatories no higher than 34 inches, grab bars at 33 to 36 inches, and a 60-inch turning space. Texas projects of $50,000 or more require TDLR registration and review.
Do restaurants in Florida need plan review?
Yes. Florida DBPR's Division of Hotels and Restaurants reviews plans for food service establishments that are new, converted from another use, remodeled, or reopening after being closed at least 18 months. You submit an application, a scale floor plan with equipment and a sample menu, and online applications are typically reviewed within 30 days. Plumbing items include handwash sinks, warewashing setup, a mop sink and backflow devices on hose faucets.
How often do commercial backflow preventers need testing?
In Florida, backflow assemblies at non-residential service connections must be tested after installation or repair and at least annually. In Texas, assemblies must be tested on installation by a licensed tester, and those protecting against health hazards at least annually. Your water utility may set additional requirements and will send notices when tests are due.
Sources
- Florida Building Code, Plumbing 2023, Chapter 4 (via UpCodes)
- ICC: Florida Building Code - Plumbing, 8th Edition (2023)
- U.S. DOJ: 2010 ADA Standards for Accessible Design
- TDLR: 2012 Texas Accessibility Standards
- Texas Government Code 469.101 (TDLR plan review threshold)
- Texas Government Code 469.102 (submission; registration before permit)
- Florida DBPR Division of Hotels and Restaurants
- Florida DBPR: Food service plan review
- Texas DSHS: Retail Food Establishments
- 30 TAC 290.44 (backflow assembly testing)
- 30 TAC 290.46 (customer service inspections)
- Fla. Admin. Code 62-555.360 (cross-connection control)
- Texas Comptroller Publication 94-116: Real Property Repair and Remodeling
- Texas Comptroller Publication 96-259: Taxable Services
- TSBPE: Tradesman Plumber-Limited
- TSBPE: Endorsements
- TSBPE: Responsible Master Plumber
- Jacksonville Building Inspection Division FAQs
- Dallas Building Inspection: plumbing and mechanical codes
- San Antonio DSD: Codes and Ordinances
- Houston Amendments to the 2021 UPC
- Austin: Building Technical Codes
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


