Local Guide · Roofing
How to Measure a Roof and Estimate Squares (With Pitch Multipliers)
You can check a roofer's or adjuster's numbers without climbing on the roof. Measure the footprint, find the pitch, multiply, add waste, and compare. Here is the math, a full pitch-multiplier table, and what aerial measurement reports can and can't tell you.
Measure your roof's footprint including overhangs, find the pitch (inches of rise per 12 inches of run), and multiply the footprint by the pitch multiplier, the square root of 1 plus (rise/12) squared. A 6/12 pitch is 1.118. Divide by 100 to get squares, then add waste: about 10% for a simple gable, 12% with a few hips or valleys, and 15% or more for complex hip roofs, per Vertigraph's estimating guide. Always compare against the roofer's measured squares.
Key facts
- A roofing square is 100 square feet of roof surface (Vertigraph; Fine Homebuilding).
- Pitch multiplier = square root of (1 + (rise/12) squared); for example 4/12 = 1.054, 6/12 = 1.118, 8/12 = 1.202, 12/12 = 1.414 (Vertigraph).
- Vertigraph's waste guide: 10% for a simple gable, 12% for one or two hips or valleys, 15% for hip-and-valley roofs, 18% to 20% for cut-up roofs with dormers and skylights.
- Most three-tab and some laminated shingles come 3 bundles per square; heavier shingles need 4 or 5 bundles per square (Fine Homebuilding).
- EagleView reported its roof area measurements were 98.43% accurate and roof slope 98.49% accurate against LiDAR benchmarks in a 2025 study it commissioned from CompassData in the Denver area.
- EagleView's own sample report says it 'DOES NOT offer an accuracy guarantee' and recommends field-verifying shaded sections.
- Fixr: steeper roofs add roof area and require harnesses or scaffolding, which raises labor cost.
- The Florida code treats roofs with a slope of 2:12 or greater as steep-slope and below 2:12 as low-slope (FRSA summary of the 2026 code).
Why measure your own roof?
Three reasons. First, to sanity-check bids: if one roofer says 24 squares and another says 31, someone is wrong, and you are paying for every square. Second, to check an insurance estimate: adjusters price roofs by the square, and a short measurement shorts your claim. Third, to budget: cost guides quote prices per square foot or per square, which only help if you know your roof's size.
Safety first. You don't need to climb on the roof to do this. Everything below can be done from the ground, from a ladder at the eave, or from the attic. If you do go up, read our DIY roof safety guide first.
What is a roofing square, and how many squares is my roof?
A square is 100 square feet of roof surface. A 2,500-square-foot roof is 25 squares. Shingles, underlayment and many other roofing products are sold and priced by the square. Most three-tab shingles and some lightweight laminated shingles come 3 bundles per square; heavier laminated shingles take 4 or 5 bundles per square, according to Fine Homebuilding. Check the wrapper on the actual product.
Your roof's square count is almost never your home's living area divided by 100. Roof area is bigger because of overhangs and slope, and smaller on two-story homes where the roof covers only half the floor area. The steps below get you to the real number.
Step 1: Measure the footprint
The footprint (also called plan area) is the area covered by the roof as seen from directly above, including overhangs.
- Sketch the outline of your house from above, including the garage and covered porches.
- Measure each outside wall with a tape or measuring wheel.
- Add the overhang: measure how far the eaves and rakes stick out and add that to each side. On a 40-by-30-foot house with 18-inch overhangs all around, the footprint is 43 by 33 feet, or 1,419 square feet.
- Break L-shapes and wings into rectangles, calculate each, and add them up.
Shortcut: the footprint from your county property appraiser's sketch usually shows heated area only, not the garage, porches or overhangs. Use it as a check, not as the answer. Satellite map tools can also help you trace the outline.
Step 2: Find the roof pitch
Pitch (or slope) is written as rise over run: how many inches the roof rises for every 12 inches it runs horizontally. A 6/12 pitch (said "six twelve") rises 6 inches every 12 inches. Florida's code calls roofs of 2:12 or more steep-slope and anything under 2:12 low-slope, which affects which roofing materials can be used.
Three ways to measure pitch without walking the roof
- At a gable end from a ladder: hold a level horizontally against the underside of the rake board, mark 12 inches along the level, and measure straight up from that mark to the roof edge. That number is the rise.
- In the attic: do the same against a rafter. Place the level against the bottom of a rafter, measure 12 inches along it, and measure vertically to the rafter.
- Phone apps: many inclinometer apps read the angle when you rest the phone on a rafter or hold it against a photo of the gable. Convert degrees to pitch with the table below.
Many roofs have more than one pitch: a steep main roof and a shallow porch roof, for example. Measure each and calculate each section separately. EagleView's sample report, for instance, lists the share of the roof at each pitch, with 61% of that sample roof at its predominant 7/12.
Step 3: Multiply by the pitch multiplier
The pitch multiplier converts the flat footprint into actual sloped roof area. The formula, as Vertigraph's estimating guide puts it: multiplier = square root of (1 + (rise / 12) squared). A roof at 12/12 (45 degrees) has 41.4% more surface than its footprint.
| Pitch | Angle (degrees) | Multiplier | Roof area per 1,000 sq ft of footprint |
|---|---|---|---|
| 1/12 | 4.8 | 1.003 | 1,003 |
| 2/12 | 9.5 | 1.014 | 1,014 |
| 3/12 | 14.0 | 1.031 | 1,031 |
| 4/12 | 18.4 | 1.054 | 1,054 |
| 5/12 | 22.6 | 1.083 | 1,083 |
| 6/12 | 26.6 | 1.118 | 1,118 |
| 7/12 | 30.3 | 1.158 | 1,158 |
| 8/12 | 33.7 | 1.202 | 1,202 |
| 9/12 | 36.9 | 1.250 | 1,250 |
| 10/12 | 39.8 | 1.302 | 1,302 |
| 11/12 | 42.5 | 1.357 | 1,357 |
| 12/12 | 45.0 | 1.414 | 1,414 |
The multiplier works for hip roofs and gable roofs alike, as long as all planes have the same pitch, because every plane tilts by the same angle. If planes have different pitches, multiply each plane's footprint by its own multiplier and add the results.
Fine Homebuilding describes two other methods. You can measure each roof plane directly as rectangles and triangles and add them up. Or, on an existing shingle roof, count the courses from eave to ridge, multiply by the 5-inch exposure of standard 12-by-36-inch shingles, and divide by 12 to get the rake length in feet. Multiply by the eave length for that plane's area.
Step 4: Add waste
Roofers order more material than the measured area because shingles get cut at rakes, hips, valleys and around chimneys and skylights, and some get damaged. Sources disagree on how much:
| Roof type | Vertigraph estimating guide |
|---|---|
| Simple gable, no hips or valleys | 10% |
| One or two hips or valleys | 12% |
| Hip-and-valley roof, multiple intersections | 15% |
| Cut-up roof with dormers, skylights, turrets | 18% to 20% |
EagleView's sample measurement report shows a waste table from 0% to 28% and labels one column as suggested for that roof. It says actual waste depends on installation technique, crew experience, the shingle product and salvage from the site.
A veteran roofer writing in Fine Homebuilding uses much smaller numbers: about 1% waste for a simple roof and 5% or more extra for a complex roof with open valleys, and notes fall-off and trimmings can add up to 5% of the shingles needed. His point is that there is no formula for waste; it comes from experience. The higher percentages in estimating guides build in a cushion.
How much waste should I add for a hip roof? A common estimating figure is about 15%, versus about 10% for a simple gable. Hip roofs have more cut edges along every hip line. If the waste figure in a quote or insurance estimate seems far off, ask how it was chosen.
Extras that aren't in the main square count
- Starter strip at eaves and often rakes. Vertigraph: about 100 linear feet per bundle.
- Hip and ridge caps. Fine Homebuilding: about 35 linear feet per bundle of three-tab caps; Vertigraph cites 20 to 25 linear feet per bundle for bagged hip-and-ridge shingles. Check the product.
- Valleys. Fine Homebuilding suggests two extra shingles per linear foot of valley.
- Drip edge (eaves plus rakes), step flashing and underlayment, each measured separately.
EagleView's sample report notes that its waste table does not include material for ridge, hip and starter, and it rounds squares up to the nearest third of a square.
How to measure ridges, hips, valleys and edges
Squares cover the field shingles, but many line items on a bid or insurance estimate are priced by the linear foot: drip edge, starter, ridge cap, hip cap, valley metal and step flashing. You can estimate these from the ground with three formulas.
- Eaves: the horizontal edges along the gutters. Measure them directly, overhang included. On a simple hip roof, the eaves run around the whole perimeter.
- Rakes: the sloped edges at gable ends. Rake length = the horizontal distance from eave to ridge x the pitch multiplier.
- Hips and valleys: where two planes of the same pitch meet at a square corner, hip or valley length = the horizontal run of the plane (eave to ridge, measured flat) x the hip-and-valley factor below.
- Ridge: on a rectangular hip roof with equal pitches, the ridge is the long side minus the short side of the footprint. On a gable roof, it equals the length of the house plus the rake overhangs.
The hip-and-valley factor is the square root of (2 + (rise/12) squared). It is bigger than the pitch multiplier because a hip runs diagonally across the corner.
| Pitch | Pitch multiplier (rakes) | Hip and valley factor |
|---|---|---|
| 4/12 | 1.054 | 1.453 |
| 5/12 | 1.083 | 1.474 |
| 6/12 | 1.118 | 1.500 |
| 7/12 | 1.158 | 1.530 |
| 8/12 | 1.202 | 1.563 |
| 10/12 | 1.302 | 1.641 |
| 12/12 | 1.414 | 1.732 |
Linear feet for the Houston example
Using the 63-by-41-foot footprint and 6/12 hip roof from the worked example below, and ignoring the garage valley for simplicity:
- Eaves and drip edge: perimeter = 2 x (63 + 41) = 208 linear feet. A hip roof has no rakes, so drip edge is about 208 feet.
- Hips: the run from eave to ridge is half the short side, 20.5 feet. Each of the 4 hips is 20.5 x 1.5 = about 31 feet, or about 123 feet total.
- Ridge: 63 - 41 = 22 feet.
- Starter: about 208 feet along the eaves. At Vertigraph's figure of about 100 linear feet per bundle, that is about 3 bundles.
- Hip and ridge cap: 123 + 22 = 145 linear feet. At Vertigraph's 20 to 25 linear feet per bundle, about 6 to 8 bundles.
Compare these with the line items on your estimate. An insurance estimate that lists drip edge only along part of the eaves, or no hip cap on a hip roof, is worth asking about.
Underlayment and water barrier
Underlayment is also figured from the roof area, but the method matters. In the two-layer #30 felt method described in IBHS's FORTIFIED roofing checklist, each 36-inch-wide course overlaps the one below by 19 inches, leaving only 17 inches exposed, so it uses roughly twice the felt of a single layer. A full self-adhered membrane, or 4-inch tape over every deck seam, is another option the checklist lists. Florida requires a secondary water barrier on every site-built single-family reroof (Fla. Stat. 553.844), so make sure your bid says which method is priced and how much of it.
A worked example
A one-story Houston ranch home measures 60 by 38 feet at the walls, with 18-inch overhangs. It has a hip roof at 6/12 pitch, a covered back patio included in the roof, and one valley where the garage meets the house.
- Footprint: (60 + 3) x (38 + 3) = 63 x 41 = 2,583 square feet.
- Pitch multiplier: 6/12 = 1.118.
- Roof area: 2,583 x 1.118 = about 2,888 square feet = 28.9 squares.
- Waste: hip roof with a valley, use 15%: 28.9 x 1.15 = about 33.2 squares to order.
- Bundles: at 3 bundles per square, about 100 bundles of field shingles, plus starter and hip-and-ridge caps.
Now compare. If a bid lists 29 squares measured and 33 squares ordered, it matches. If an insurance estimate shows 24 squares, ask the adjuster to recheck. If a bid lists 40 squares, ask for the measurement report.
To estimate cost, multiply the measured roof area by a per-square-foot range. Fixr's 2026 national range of $3.75 to $11 per square foot would put this roof at about $10,800 to $31,800. See our roof cost guide for Texas and Florida figures.
Can I measure my roof from a satellite map?
Yes, for the footprint. Many free online map programs, including Google Earth, have a ruler or area tool you can use to trace the outline of your roof from above. Tracing the roof's outer edge from the image captures the overhangs, which is what you want.
Tips for better results:
- Trace the roof edge, not the shadow. Shadows on the ground make the roof look bigger on one side.
- Watch for trees. Live oaks in Houston and Austin and tree canopies across much of Florida can hide edges. Use the measurements you can see and fill in with a tape measure.
- Check the image date. A new addition, carport or pool enclosure may not show up in older imagery.
- Remember it is flat. A satellite view gives you the footprint only. You still need the pitch, measured from the gable or attic as described above, and the pitch multiplier to get the true roof area.
- Cross-check one wall. Measure one wall with a tape and compare it with the map. If the two disagree by more than a foot or so, recheck your tracing.
Satellite tracing is a good way to check a bid, but it is not a substitute for a roofer's measurement when you order materials. Aerial measurement reports, covered below, go further by estimating each plane's pitch.
Are satellite roof measurements accurate (EagleView, Hover)?
Generally close on simple, clearly visible roofs, with limits you should know.
- Aerial reports such as EagleView use aerial or satellite imagery to measure each roof plane, pitch, and the lengths of ridges, hips, valleys, rakes, eaves and flashing. EagleView reported in June 2025 that a study it commissioned from surveying firm CompassData, comparing its measurements with drone and ground LiDAR on single-family homes in the Denver area, found 98.77% accuracy for roof lines, 98.43% for roof area and 98.49% for slope. That is a vendor-commissioned study in one metro area.
- The fine print: EagleView's own sample report says that because of factors such as "tree coverage, poor images, low photo resolution or other blockages," the report "DOES NOT offer an accuracy guarantee," and recommends field verification of yellow-shaded sections. It also notes small penetrations under 3 by 3 feet may need field checking, and some products note only the predominant pitch.
- Phone-photo tools such as Hover build a 3D model from photos you or a contractor take around the house. We did not find an independent, published accuracy study we could verify, so treat any such tool's accuracy claims as vendor claims.
Where aerial reports go wrong: heavy tree cover (common in Houston, Austin and much of Florida), recent additions not in the imagery, multiple pitches recorded as one, and flat or low-slope sections. Use a report as a strong starting point, and do the quick footprint-times-multiplier check above. Many roofers and insurers use these reports, so ask to see the one behind your quote or estimate.
Measuring flat and low-slope roofs
Flat and low-slope roofs, common on Florida homes, additions, carports and Texas commercial buildings, are measured differently. The pitch multiplier is close to 1 (a 1/12 roof is only 0.3% larger than its footprint), so the footprint is nearly the roof area. The extra material goes elsewhere:
- Parapet walls: the membrane usually runs up and over them, so measure parapet height and length and add that wall area.
- Edges and drains: measure edge metal in linear feet and count drains, scuppers and penetrations.
- Insulation and tapered systems: commercial roofs often have insulation layers that change the job's cost far more than the membrane area does.
Fixr prices flat roof repairs at $2 to $10 per square foot depending on material. For full systems, see our flat roof guide.
Using your measurements with insurance and contractors
- Insurance estimates list roof area in squares, waste, and line items such as drip edge, starter, ridge cap and flashing. Compare each against your measurements. TWIA encourages policyholders to get line-item contractor estimates breaking out labor and materials and says it will compare them with its adjuster's estimate. See how to read a roofing estimate.
- Bids: ask every bidder for measured squares, waste percentage and the measurement source. Make sure they all measured the same roof, including porches and the garage.
- Florida tile and metal roofs: waste and accessory needs differ from shingles. Ask the roofer to explain tile counts, trim pieces and underlayment coverage.
- Low-slope sections under 2:12 usually need a different roofing system than the main roof; make sure they're priced separately.
How to choose a provider
- Sketch the house outline from above, including garage, porches and overhangs.
- Measure each wall and add the overhang to get the footprint.
- Measure pitch from a ladder at the gable or in the attic.
- Look up the pitch multiplier and multiply each section's footprint.
- Divide by 100 to get squares.
- Add waste: about 10% gable, 12% simple hip or valley, 15% or more complex hip.
- Measure ridges, hips, eaves, rakes and valleys in linear feet for accessories.
- Compare your numbers with every bid and any insurance estimate.
- Ask for the aerial measurement report behind a quote or claim.
- Never walk a steep or wet roof to measure it.
Related roofing guides
- How Much Does a New Roof Cost in Texas and Florida? (What Actually Drives the Price)
- How to Compare Roofing Quotes Apples-to-Apples (With a Line-Item Checklist)
- Roofing Glossary: 250 Terms From Your Estimate, Contract, and Insurance Letter
- Roof Insurance Claim Step by Step: From First Call to Final Check
- Asphalt Shingle Roofs: Which Type, How Long They Last, and What Warranties Pay
- DIY Roof Repair in Texas and Florida: What You Can Safely Do Yourself, and What Is Illegal or Dangerous
Roofing by state and city
Questions people ask
How do I calculate roof pitch from degrees?
Pitch in inches per 12 equals 12 times the tangent of the angle. Common values: about 18.4 degrees is 4/12, 26.6 degrees is 6/12, 33.7 degrees is 8/12, and 45 degrees is 12/12. Many phone inclinometer apps show both degrees and pitch. Use the table on this page to convert either way.
Is roof area the same as my home's square footage?
No. A one-story home's roof is usually larger than its living area because of overhangs, garages, porches and slope. A two-story home's roof is often smaller than its total living area because the roof covers only the footprint. Always work from the footprint, not the listing's square footage.
Why do roofers' measurements differ?
Different measurement methods, whether garages and porches were included, different pitch readings, and different waste factors. Some quotes list measured squares and others list squares ordered with waste. Ask each roofer for both numbers and their source, such as an aerial report or a hand measurement.
How many bundles of shingles do I need per square?
Usually 3 for standard three-tab and many lightweight architectural shingles, and 4 or 5 for heavier designer shingles, according to Fine Homebuilding. Check the coverage printed on the wrapper. Remember to add starter shingles and hip-and-ridge caps, which are separate from the field-shingle count.
Can I trust the square count in my insurance estimate?
Check it. Adjusters often use aerial measurement or a hand measurement, and both can miss sections, porches or pitch changes. Do the footprint-times-multiplier check yourself. If your number is meaningfully higher, ask the adjuster or insurer for the measurement report and request a re-inspection, providing your own measurements and photos.
Does a steeper roof cost more per square?
Usually yes. A steeper roof has more squares over the same footprint, and Fixr notes that steep roofs need harnesses or scaffolding that slow the crew and raise labor costs. Ask whether your bid adds a separate charge for steepness, and how it is calculated.
How many squares is a 2,000-square-foot house?
It depends on stories, overhangs and pitch. For a one-story home with a 2,000-square-foot footprint including overhangs and a 6/12 pitch, the roof is about 2,000 x 1.118 = 2,236 square feet, or about 22.4 squares, before waste. With 15% waste for a hip roof, you would order about 26 squares. A two-story home with 2,000 square feet of living space has a much smaller footprint and roof.
How do I calculate hip and valley lengths?
For two roof planes of the same pitch meeting at a square corner, multiply the plane's horizontal run (eave to ridge, measured flat) by the square root of 2 plus (rise/12) squared. At 6/12, that factor is 1.5, so a plane with a 20-foot run has hips about 30 feet long. Hip and ridge cap shingles are ordered by these linear feet, not by squares.
Sources
- Vertigraph: How to calculate roofing squares (pitch multiplier, area, waste), updated May 11, 2026
- Fine Homebuilding: How to Estimate Materials for Roofing Projects (excerpt from Roofing with Asphalt Shingles)
- EagleView: Roof measurements confirmed to be 98.77% accurate compared to independent benchmark measurements (June 4, 2025)
- Roofing Contractor: EagleView Roof Measurements Confirmed 98.77% Accurate
- EagleView: Full House Sample Report (2025)
- Fixr: How Much Does a Roof Replacement Cost? (2026 data)
- FRSA (Mike Silvers): Additional Changes in the 2026 Ninth Edition of the FBC (slope definitions)
- FRSA (Manny Oyola Jr.): Tile Changes in the 2026 Ninth Edition FBC (steep slope 2:12)
- TWIA: Policyholders (line-item estimates)
- Fixr: Flat Roof Repair Cost
- IBHS FORTIFIED: Roofing Checklist, High Wind and Hail (2020)
- Fla. Stat. 553.844 (2026): Windstorm loss mitigation; roofs
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


