Local Guide · Residential solar installers
Should You Replace Your Roof Before Solar? Roof Age, Re-Roofing and Removal Costs
How to match roof life to solar life, what removal and reinstallation costs, how panels attach to shingle, tile and metal, and the Texas and Florida roof-age insurance rules.
Replace your roof before installing solar if its remaining life is much shorter than the solar system's expected life. InterNACHI estimates about 20 years for 3-tab shingles, 30 for architectural shingles and 40 to 80 for metal. Removing and reinstalling panels later typically costs $1,500 to $6,000 (EnergySage, 2026). In Florida, roof age also affects insurance under s. 627.7011, and in Texas hail often forces early re-roofs.
Key facts
- InterNACHI estimates roof life at 20 years for 3-tab shingles, 30 for architectural shingles, 40 to 80 for metal, and 100+ for clay or concrete tile.
- EnergySage (Nov. 2026): removing and reinstalling solar typically costs $1,500 to $6,000, about $200 to $300 per panel.
- EnergySage's 2026 average for replacing a roof and installing solar together is about $40,600 before incentives.
- Florida s. 627.7011(5): insurers can't refuse or nonrenew solely for roof age under 15 years, and must allow an inspection for older roofs.
- Florida s. 553.844(5): for roofs built to the 2007 FBC or later, repairing 25% or more requires only the repaired portion to meet current code.
- TDI (Sept. 29, 2026) says Texas insurers can't decline or nonrenew based solely on the age of a home or its roof.
- Florida Rule 61G4-15.021 lets certified solar contractors do related roofing work within 18 inches of each penetration, to NRCA practices.
- The 2026 Florida Building Code, Residential, adds a PV flashing section (R905.17.5) and requires BIPV roof coverings to be listed to UL 7103.
Should I replace my roof before installing solar?
If your roof has less useful life left than the solar system is expected to last, replacing it first usually makes sense. Solar panels are commonly expected to work for decades. If the roof under them wears out in a few years, the panels have to come off and go back on, which costs money and creates a new set of roof penetrations.
A simple rule: compare the roof's remaining life to the solar system's expected life. If the gap is large, deal with the roof first.
In Texas and Florida there are extra reasons to look closely:
- Hail in Texas forces roof replacements in Dallas-Fort Worth, San Antonio and the Austin area. A hail claim on a roof with solar means paying for removal and reinstallation (R&R).
- Insurance in Florida is tied closely to roof age and condition, and the state has specific roof-age rules for insurers.
- Hurricanes in both states make roof condition and attachment quality matter more. IBHS calls re-roofing one of the two most significant ways to improve a home's hurricane resilience.
How long do roofs last by material?
The International Association of Certified Home Inspectors (InterNACHI) publishes an estimated life chart. It's a guideline assuming normal wear and regular maintenance, not a guarantee. Texas heat and hail and Florida sun, salt air and storms can shorten real life.
| Roof material | InterNACHI estimated life | Solar notes |
|---|---|---|
| Asphalt shingles, 3-tab | 20 years | Common on older homes; standard flashed mounts |
| Asphalt shingles, architectural | 30 years | Most common on newer Texas and Florida homes |
| Clay or concrete tile | 100+ years (the tile itself) | Common in South Florida; mounting is more complex |
| Metal | 40 to 80 years | Standing seam allows clamp mounting without holes |
| Wood | 25 years | Less common; ask about fire class |
| Built-up roofing (BUR) | 30 years | Flat or low-slope roofs |
| Modified bitumen | 20 years | Flat roofs; penetrations need careful sealing |
| EPDM rubber | 15 to 25 years | Flat roofs |
| TPO | 7 to 20 years | Flat roofs; often ballasted or mechanically attached racks |
Tile roofs: the tiles may last a very long time, but the underlayment beneath them can wear out much sooner. Ask your roofer about the underlayment's condition and age, not just the tile.
How old is too old for a roof to get solar?
There is no legal cutoff. Many installers won't put panels on a roof they judge to be near the end of its life, and some require a roof inspection first. A practical way to decide:
- Find the roof's install year from permit records, your home inspection, or the roofer's invoice.
- Subtract it from the material's expected life to estimate remaining years.
- Have a licensed roofer inspect for soft decking, granule loss, cracked or slipped tiles, rusted metal, and leaks.
- If remaining life is well short of the solar system's expected life, plan the re-roof first or at the same time.
Example: a 2008 architectural shingle roof in Plano is 18 years old in 2026. Its chart life is 30 years, so it might have about 12 years left, less if it has taken hail. Adding solar now likely means paying for R&R in about a decade. Replacing it first avoids that.
Example: a 2019 concrete tile roof in Coral Springs has a long-lived tile but should have its underlayment and flashing checked. If it's sound, solar may go on now with tile-specific mounts.
Miami-Dade's PV permitting materials list "informed consent" before installing a PV array on an existing roof, a sign that reviewers expect owners to understand the roof's condition first.
What does it cost to remove and reinstall solar panels?
EnergySage (page updated November 12, 2026) says removing and reinstalling solar panels typically costs $1,500 to $6,000 and can top $7,000 for larger systems, or roughly $200 to $300 per panel. Its 2026 figure for replacing a roof and installing solar at the same time is about $40,600 on average before incentives, based on about $31,000 for solar and about $10,000 for an asphalt shingle roof.
R&R can include:
- Electrical disconnection and later recommissioning by a licensed electrician.
- Removing panels, rails and mounts, and storing them safely.
- New flashing and attachments on the new roof.
- Permits, inspections, and on the Texas coast, windstorm certification.
- Replacing any panel broken in handling. If your model is discontinued, matching can be hard.
Who does R&R matters. Your installer's workmanship warranty may be voided if someone else removes the system. Ask your installer for an R&R price in writing when you sign, so you know the cost later. See removal, reinstall and repair.
How are solar panels attached to shingle, tile and metal roofs?
Asphalt shingle
Mounts are screwed through the shingles and decking into rafters or trusses, then covered with flashing: a metal or engineered piece slipped under the shingles above so water flows over it. Miami-Dade's workshop notes shingle penetration flashing must follow National Roofing Contractors Association practices. Palm Beach County's building advisory board said in 2023 that only attachments into trusses or rafters with lag screws had been validated for its wind loads.
Clay or concrete tile
Tile is a "discontinuous" roof system, per Miami-Dade, so penetrations need tile-compatible flashing. Common methods are:
- Tile hooks: a bracket fastened to the rafter under the tile, which comes out through the joint between tiles.
- Tile replacement mounts: a tile is removed and replaced with a metal or composite flashed piece that holds the mount.
- Stand-off mounts with flashing: a post through the tile with sealed flashing.
Tiles crack easily when walked on, so ask how breakage will be handled and whether spare matching tiles are available.
Standing-seam metal
Clamps grip the raised seams without drilling through the roof. This is a big reason metal roofs pair well with solar. Exposed-fastener metal roofs need flashed mounts instead.
Flat and low-slope roofs
Arrays may use ballasted racks (held down by weight), mechanically attached racks, or a mix. Wind design differs on low-slope roofs: ASCE 7-16, adopted in Florida's 2020 code, added a separate method for low-slope arrays. Miami-Dade warns that pitch pans filled with roof cement are a poor long-term choice for penetrations because the cement shrinks.
Florida 2026 code
The 9th Edition (2026, effective for permit applications submitted on or after December 31, 2026) Florida Building Code, Residential, adds a flashing section for PV panels and modules (R905.17.5) requiring flashing to follow the roofing chapter and the maker's instructions, and requires building-integrated PV (BIPV) roof coverings to be listed to UL 7103.
Is a metal roof better for solar?
Often, yes. A standing-seam metal roof can last 40 to 80 years by InterNACHI's estimate, closer to the life of a solar system, and clamp mounts avoid roof penetrations. The downsides are higher upfront roof cost and that not every metal roof is standing-seam. If you are replacing your roof anyway and plan solar, ask roofers to quote standing-seam metal alongside shingle and tile. More detail: solar on tile, metal and shingle roofs.
Do solar installers cause roof leaks, and who is responsible?
Every penetration is a potential leak if it isn't flashed well. Most leaks trace to missed rafters, poor flashing, wrong sealant, or broken tiles. Two warranties matter:
- Installer workmanship / roof penetration warranty: covers leaks caused by the solar installation. Get the length and terms in writing.
- Roofing manufacturer and roofer warranties: may be voided if another contractor penetrates the roof without following the roofing maker's requirements. Ask your roofer before solar work begins.
If a leak appears near mounts, document it with photos and call the solar installer first. If they deny it, a roofer's written inspection can show whether the leak is at a solar penetration.
Will solar void my roof warranty?
It can, if the roofing manufacturer or roofer requires approved methods or contractors for penetrations. Some roofing warranties allow approved solar mounts. Ask for written confirmation before installation.
Florida's 25% roof repair rule and solar
Florida used to be known for a "25% rule" requiring a full re-roof when 25% or more of a roof was repaired or replaced. Section 553.844(5), Florida Statutes, now says that if a roof or roof section was built, repaired or replaced to the 2007 Florida Building Code or later, and 25% or more of it is being repaired, replaced or recovered, only the repaired, replaced or recovered portion must meet the current code.
What it means for solar: on a newer roof (2007 code or later), partial storm repairs around an array may not trigger a full re-roof. On an older roof built under earlier codes, a large repair can still require the whole roof to be brought up to code, which means R&R for your panels. Ask your roofer and building department which rule applies to your roof.
Can my insurer drop me for roof age if I have solar?
Florida
Under s. 627.7011(5), Florida Statutes, an insurer may not refuse to issue or renew a homeowners policy on a roof less than 15 years old solely because of roof age. For a roof at least 15 years old, the insurer must allow an inspection by an authorized inspector, at the homeowner's expense, before requiring replacement; if the inspection shows at least 5 years of useful life left, the insurer may not refuse to issue or renew solely because of roof age. Roof age runs from the last date 100% of the roof was built or replaced. Insurers can still use other lawful underwriting reasons.
The statute doesn't mention solar. But putting panels on a roof that is about to hit the 15-year mark can create a problem: an inspector may need to see under the array, and a required replacement means R&R.
Texas
TDI said on September 29, 2026 that it is clarifying its rule that insurers can't decline or nonrenew a home policy based on the age of the house or its roof alone. Insurers may base decisions on the physical condition of the home and components such as roofing. A worn roof can still cause problems even if age alone can't.
Whatever your state, tell your insurer you're adding solar, and ask how roof age and condition will be judged at renewal. See solar and homeowners insurance.
Should the roofer and solar installer coordinate?
Yes. When re-roofing and adding solar together:
- Have the roofer and solar installer agree on mount locations, flashing products and who installs them.
- Many installers prefer to place mounts and flashing while the roof is open, then have the roofer finish around them.
- Get the roofer's written approval of the flashing method if you want to keep the roofing warranty.
- Schedule inspections in the right order.
- On TWIA-insured Texas coastal homes, TDI requires that only one engineer or inspector file the windstorm certification for a combined re-roof and solar scope. Plan that upfront.
Licensing: roofing vs solar
In Florida, a certified solar contractor may do roofing work directly related to the solar installation, such as cutting openings, installing flashing and attaching brackets, limited to 18 inches around each penetration and done to NRCA practices (Rule 61G4-15.021, cited in Miami-Dade's workshop). Section 489.113(3)(f) lets solar contractors do minor roofing work tied exclusively to installing residential solar without subcontracting. A full re-roof still needs a licensed roofing contractor. Florida electrical contractors do not have the solar contractor's roofing authorization, per Miami-Dade.
In Texas, the electrical part of solar must be done by a TDLR-licensed electrical contractor and electricians. Check how your city regulates roofing contractors and permits.
Can solar be installed on a new roof right away?
Yes, once the roof passes final inspection. Many owners schedule solar right after a re-roof to avoid two rounds of work. Points to check:
- Keep the roofer's final invoice and permit, which document roof age for insurance.
- Ask the roofer whether a waiting period applies for warranty or material reasons.
- If the new roof was paid by an insurance claim, coordinate so R&R is part of the claim.
Florida grants for roof work
My Safe Florida Home grants may cover roof improvements, including roof-to-wall connections, roof-deck attachment, secondary water resistance and roof covering replacement, when recommended by the program's inspection (s. 215.5586). The program depends on yearly legislative funding. As of November 19, 2026, its site said the applicant portal had been temporarily unavailable since November 10 while it moves to a new platform.
Texas hail and repeat re-roofing
In Hail Alley, roofs may be replaced well before their chart life. NOAA NCEI records repeated billion-dollar hail events in Dallas-Fort Worth, San Antonio and the Austin area. If your neighborhood has had hail re-roofs every several years, budget for future R&R, consider impact-rated roofing, and read solar panels and hail.
Remember that Texas law bars contractors from waiving your deductible (Business and Commerce Code 27.02), and TDI warns against anyone who offers.
How to choose a provider
- Find the roof's install year and material.
- Get a licensed roofer's inspection, including underlayment on tile roofs.
- Compare remaining roof life with the solar system's expected life.
- Ask installers for the attachment method and flashing product for your roof type.
- Get the installer's roof penetration warranty and R&R price in writing.
- Ask your roofer whether solar mounts affect the roofing warranty.
- If re-roofing, coordinate mount placement and inspections between both contractors.
- In Florida, check roof age against the 15-year insurance rule before adding panels.
- On the Texas coast, plan windstorm certification for combined roof and solar work.
- Keep permits, invoices and inspection reports for insurance.
Related residential solar installers guides
- Can You Put Solar on a Tile, Metal, Flat or Shingle Roof? Plus Solar Shingles Explained
- How Much Does It Cost to Remove and Reinstall Solar Panels, and Who Can Do It in Texas and Florida?
- Solar Panels and Hail: Ratings, Damage, Insurance Claims and North Texas Risk
- Does Homeowners Insurance Cover Solar Panels? Texas and Florida Rules
- Can Solar Panels Survive a Hurricane? Wind Ratings, Codes and What Fails
- What Do Solar Warranties Actually Cover? Panels, Inverters, Batteries, Workmanship and Roof Leaks
- HOA Solar Rules in Texas and Florida: What Your HOA Can and Cannot Do
- Is There Still a Federal Solar Tax Credit in 2026?
Residential solar installers by state and city
Questions people ask
Should I replace a 10-year-old shingle roof before solar?
Maybe not. A 10-year-old architectural shingle roof has about 20 years of chart life left by InterNACHI's estimate if it's in good shape. A 10-year-old 3-tab roof has about 10. Get a roofer's inspection, and if hail has hit your area, check for damage. If remaining life is far short of the solar system's, re-roof first.
Does a roof replacement under solar qualify for a tax credit?
Not under the federal residential credit for 2026. The Section 25D credit ended for systems whose installation is completed after December 31, 2025, and even before then the IRS said ordinary roofing, like shingles and trusses, did not qualify while solar shingles did. Check our federal credit page for the current status.
Is it cheaper to re-roof and add solar at the same time?
It avoids paying for removal and reinstallation later, which EnergySage puts at $1,500 to $6,000 for typical systems. It also lets mounts and flashing go in with the new roof. EnergySage's 2026 average for doing both together is about $40,600 before incentives. Get separate line-item quotes so you can compare.
Can solar go on a flat roof?
Yes. Flat and low-slope roofs use ballasted or attached racks tilted toward the sun. ASCE 7-16 has a specific wind method for low-slope arrays. Check the roof membrane's age and ask how penetrations or ballast will protect it. Miami-Dade advises against relying on pitch pans filled with roof cement.
What is flashing and why does it matter?
Flashing is the metal or engineered piece that directs water around a roof penetration, such as a solar mount. Good flashing slides under the roofing above it and over the roofing below. Florida's 2026 residential code adds a section requiring PV flashing to follow the roofing rules and the maker's instructions. Most solar leaks are flashing failures.
Who pays for R&R if hail ruins my roof?
Many adjusters include removal and reinstallation in a covered roof claim, since it's needed for the repair. Make sure the estimate lists it, along with flashing and electrical recommissioning. Your wind and hail deductible applies. If R&R is missing, send the installer's quote and ask for a revised estimate.
Can my HOA block me from re-roofing with solar shingles?
Texas Property Code 202.010 treats a solar roof tile as a solar energy device, which brings HOA solar protections into play with listed exceptions. Florida's s. 163.04 limits HOA bans on solar collectors. Product approvals and code rules still apply. See our HOA solar rights page.
Do I need a roof inspection before solar?
Not always by law, but it is wise, and many installers require one. Miami-Dade's permitting materials mention informed consent before placing PV on an existing roof. An inspection report also helps with insurance, since Florida and Texas insurers look at roof condition.
Sources
- InterNACHI: Standard estimated life expectancy chart for homes
- EnergySage: Solar panel roof replacement (updated Nov. 12, 2026)
- Florida Statutes 553.844
- Florida Statutes 627.7011
- TDI: Texas homeowners protected from being denied insurance based on roof age (Sept. 29, 2026)
- Miami-Dade County: PV solar permitting workshop presentation
- Palm Beach County BCAB: Rooftop solar PV mounting technical advisory (July 19, 2023)
- Florida Building Commission: Analysis of Changes, 9th Edition (2026) FBC Residential
- Florida Building Commission: ASCE 7-16 fact sheet
- Florida Statutes 489.113
- Florida Statutes 489.105
- Florida Statutes 215.5586 (My Safe Florida Home)
- My Safe Florida Home
- IBHS FORTIFIED: Before the storm, a homeowner's guide to hurricane readiness
- TDI Windstorm Inspections Program newsletter (Apr. 18, 2023)
- TWIA: Windstorm certification
- NOAA NCEI Billion-Dollar Disasters: Texas
- Texas Business and Commerce Code ch. 27
- TDLR: Electricians
- IRS: Residential Clean Energy Credit
- Texas Property Code ch. 202
- Florida Statutes 163.04
- Miami-Dade County: Florida Building Code 9th Edition code change notice
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


