Local Guide · Swimming pool builders and contractors
Gunite vs Fiberglass vs Vinyl Pools: Which Is Right for a Texas or Florida Yard?
How the three main inground pool types compare on cost, lifespan, install time, chemicals and, most important in Texas and Florida, how they handle clay, rock, sand and groundwater.
Concrete (gunite or shotcrete) is the most flexible and usually the best fit for rock, odd shapes and large custom pools, but it costs more over time because plaster needs resurfacing every 10 to 15 years. Fiberglass installs fastest and has a smooth, low-maintenance surface, but shells are limited by road width and need careful backfill and groundwater control. Vinyl liner has the lowest typical first cost but needs a new liner every 5 to 9 years.
Key facts
- The American Shotcrete Association calls dry-mix shotcrete "gunite" and treats shotcrete as a placement method for concrete.
- ASA says dry-mix pool shotcrete should have a minimum 28-day compressive strength of 4,000 psi and recommends at least 7 days of curing.
- Fixr (Jan. 2025) lists average installed prices of about $45,000 for vinyl liner, $60,000 for concrete and $70,000 for fiberglass, each for a different package size.
- Fixr (2025) says concrete pools need resurfacing every 10 to 15 years, vinyl liners every 5 to 9 years, and fiberglass gelcoat resurfacing costs $10,000 to $20,000.
- Texas's legal load width without a permit is 8 feet 6 inches; permitted loads on Interstate highways are capped at 16 feet, and loads over 16 feet need two escorts (TxDMV).
- Florida Building Code R4501.21.4 requires a hydrostatic relief device in areas of anticipated water table, except plastic liner pools.
- FBC R4501.19 says vinyl liner and fiberglass pools must be filled with water upon installation, unlike concrete pools.
- Fixr (2025) says polymer or plastic walls are needed for saltwater use in vinyl pools; most vinyl pools have metal walls.
What is the difference between gunite, shotcrete, fiberglass and vinyl pools?
Concrete pools are built in place. The crew digs the hole, ties a cage of steel rebar, runs the plumbing, and sprays concrete over the steel to form the shell. Then they add tile, coping and an interior finish such as plaster, quartz or pebble. There are two ways to spray the concrete:
- Gunite (dry-mix shotcrete): dry cement and sand travel through the hose, and water is added at the nozzle. The nozzle operator controls the water.
- Shotcrete (wet-mix): concrete is mixed with water first, usually delivered by a ready-mix truck, then pumped and sprayed.
The American Shotcrete Association (ASA) describes shotcrete as "a placement method for concrete" and uses "dry-mix shotcrete (Gunite)" for the dry process. In other words, both are concrete. The quality depends on the mix, the steel, the nozzle operator and the curing.
Fiberglass pools are one-piece shells molded in a factory, trucked to your home, set in a prepared hole, plumbed and backfilled. The surface is a gelcoat, a smooth resin finish.
Vinyl liner pools use walls made of steel or polymer panels set around the hole, a floor of packed sand, grout or similar base, and a custom-fit vinyl sheet that holds the water. Fixr's 2025 guide notes most vinyl pools have metal walls and that polymer or plastic walls are needed for saltwater use.
Quick comparison table
| Factor | Concrete (gunite or shotcrete) | Fiberglass | Vinyl liner |
|---|---|---|---|
| Typical installed cost (Fixr, Jan. 2025) | $50,000 to $90,000, average $60,000 (12 x 24 package) | $50,000 to $95,000, average $70,000 (15 x 30 with deck and heater) | $35,000 to $65,000, average $45,000 (12 x 24) |
| Shape and size | Any shape, size and depth | Factory molds only; width limited by road transport | Many shapes; custom liners possible |
| Typical build time | Longest; Fixr says 3 to 12 weeks for install because concrete must cure | Shell set in a few days once on site (Fixr) | Faster than concrete (Fixr gives no exact time) |
| Surface | Plaster, quartz, pebble or tile; slightly rough and porous | Smooth gelcoat | Smooth vinyl |
| Main recurring cost | Resurfacing every 10 to 15 years | Gelcoat resurfacing late in life, $10,000 to $20,000 | Liner every 5 to 9 years, $3,000 to $6,000 |
| Lifespan stated by Fixr (2025) | 30+ years for concrete pools; Fixr also cites up to 100 years for gunite and 50+ for shotcrete structures | 25 to 50 years with good maintenance | Walls can last indefinitely; liner 5 to 9 years |
| Groundwater risk | Needs hydrostatic relief in high water table areas (FBC) | Must be kept full; uplift risk if drained | Liner can float or wrinkle if groundwater rises under it |
Cost averages describe different package sizes, so they are not a direct apples-to-apples price ranking. See our Texas and Florida pool cost guide for a line-by-line budget.
Is gunite or shotcrete stronger?
Neither process is automatically stronger. Strength depends on the mix design, how well the nozzle operator places it, how much "rebound" (material that bounces off) gets trapped, and curing. ASA's pool FAQ says dry-mix shotcrete "should have a minimum 28-day compressive strength of 4000 psi," and that the strength a pool needs depends on its design. ASA also cites ACI 350 (the American Concrete Institute's code for water-containing concrete structures) as applying to pools, and recommends using an ACI-certified shotcrete nozzleman.
The question map for this guide asked us to confirm ACI 506, ACI's shotcrete guide. We could not confirm from the ASA pages we loaded that ACI 506 is the referenced pool standard, so we are not citing it as one.
Questions to ask your builder:
- Is your crew's nozzle operator ACI-certified?
- What is the specified 28-day strength, and will you take test samples (cores or test panels) if I ask?
- How will you handle a cold joint if the shoot is interrupted? ASA says the old surface should be roughened, clean and dampened before new material goes on, and that bonding agents should not be used.
- How long will you cure the shell, and how? ASA recommends a minimum of 7 days of curing to control shrinkage, especially in hot, dry or windy weather.
See how a concrete pool is built for the full step list.
Which pool type lasts longest, and which is cheapest over 20 years?
All three can last decades with good care. The differences show up in the parts you replace.
Here is a simple 20-year example using only Fixr's January 2025 figures. These are our calculations, not survey results, and they leave out repairs, equipment and inflation.
| Type | Starting price (Fixr average) | Planned surface work in 20 years | Example 20-year total |
|---|---|---|---|
| Vinyl liner | $45,000 | 2 to 3 liner replacements at $3,000 to $6,000 each | About $51,000 to $63,000 |
| Concrete | $60,000 | 1 to 2 resurfacings; Fixr's average pool remodel is $15,000 | About $75,000 to $90,000 |
| Fiberglass | $70,000 | Often none in 20 years; gelcoat resurfacing $10,000 to $20,000 if needed | About $70,000 to $90,000 |
Two cautions. First, the fiberglass average includes a deck and heater, while the concrete and vinyl averages do not, so fiberglass looks more expensive than it would for the same package. Second, real life adds chemicals, power and repairs. Smooth surfaces tend to need less brushing, and concrete plaster that is kept in balance lasts longer. Treat this as a way to think, not a price promise.
Is fiberglass good in Florida heat and sun?
Fiberglass shells are used widely across hot climates. The main sun-related concerns are fading or chalking of the gelcoat over many years and a warmer surface on the steps and benches in summer. Water chemistry matters more than sunlight for gelcoat life: very low pH or high chlorine for long periods can stain or etch finishes. Florida's strong sun also burns off chlorine quickly, so many owners use stabilizer, which must be kept within limits. See pool water chemistry.
A screen enclosure helps with leaves and bugs. It reduces some sunlight, but it does not block UV fully, so finishes still age.
Do fiberglass pools pop out of the ground in Florida's high water table?
They can if they are drained when groundwater is high. An empty pool is like an empty boat: water in the soil pushes up on it. A full pool is heavy enough to stay put. That is why Florida Building Code R4501.19 notes that fiberglass and vinyl pools must be filled with water upon installation, and why R4501.21.4 requires a hydrostatic relief device (a valve that lets groundwater into the pool instead of pushing on the shell) in areas of anticipated water table, for all but plastic liner pools.
Concrete pools can also lift or crack if drained in wet conditions. The rule for every pool type in Florida and in wet parts of Houston is the same: never drain a pool without checking groundwater and getting guidance from a licensed pool professional. Some resurfacing jobs use well points to lower groundwater first. If you are told to drain your pool, ask who is responsible if it lifts.
During installation, fiberglass builders in high water table areas often use dewatering pumps and fill the shell as they backfill. Ask how your builder will do it and what happens if a storm hits mid-install. See hurricane prep for pools.
Can a fiberglass pool crack in expansive clay? How does each type handle Texas soil?
Expansive clay in Dallas-Fort Worth, Houston and parts of Austin and San Antonio swells when wet and shrinks when dry. That movement pushes on pool walls and decks.
- Concrete: A steel-reinforced shell can be engineered for clay with more steel and a thicker shell. Decks need joints and drainage so water does not soak the clay next to the pool.
- Fiberglass: The shell flexes slightly, which helps it tolerate some movement. Problems usually come from poor backfill, poor drainage or a deck tied rigidly to the shell. Ask what backfill material the builder uses and why. Clay itself is generally not used as backfill around a fiberglass shell.
- Vinyl: Walls are braced with concrete footings. Movement can show up as wrinkles or pulled liners.
In the Hill Country, deep rock is less of a movement issue but makes digging harder. Concrete can follow the shape the rock allows, while fiberglass needs a hole cut to the shell's exact shape, which may mean more rock removal.
Ask builders whether they recommend a soil report for your lot. See pool cracks and structural repair and hail and freeze damage in Texas.
Do vinyl liner pools work in Texas and Florida?
Yes, though they are less common in both states than concrete. Points to weigh:
- Liner replacement: every 5 to 9 years per Fixr 2025, at about $3,000 to $6,000. Liners come in thicknesses from 20 to 30 mil (1 mil is one thousandth of an inch). Thicker liners cost more and resist tears better.
- Hail and debris: North Texas hail can damage covers and, when the water is low or a cover is off, liners near the waterline. Branches and pets' claws can also tear liners.
- Salt systems: Fixr notes polymer walls are needed for saltwater use. Ask about wall material if you want a salt chlorine generator. See saltwater pool systems.
- Groundwater: If groundwater rises under a liner, it can lift and wrinkle it.
Which pool type needs the fewest chemicals and grows the least algae?
Smooth, non-porous surfaces such as fiberglass gelcoat and vinyl give algae fewer places to grip, so they are usually easier to brush clean. Plaster and pebble finishes are porous, and new plaster changes water chemistry during its first weeks as it cures (it raises pH). That is why concrete pools need a careful startup and why many owners of concrete pools find they add more acid over time.
In practice, sanitation needs depend more on sunlight, bather load, debris, rainfall and filtration than on the surface. A pool in full Florida sun with heavy summer rain needs close attention no matter what it is made of. See green and cloudy pool fixes.
Can you customize a fiberglass pool, and what are the shipping limits?
You choose from a manufacturer's molds. Within a mold, options often include tanning ledges, benches, step layouts, finishes and attached spas, but you cannot change the basic shape. If you want a specific length, a freeform shape to fit a narrow lot, or a deep diving area, concrete is usually the answer.
Size limits come from the road. The Texas Department of Motor Vehicles lists the legal width for most vehicles and loads at 8 feet 6 inches without a permit. With a permit, loads may be up to 16 feet wide on Interstate highways, up to 14 feet on holidays, and up to 20 feet without a route inspection certification on file. Loads wider than 14 feet need one escort, and loads wider than 16 feet need two escorts, front and rear. That is why most fiberglass shells top out around 16 feet wide: wider shells cost much more to move and need special routing. We did not find a single national rule that sets a 16-foot limit, so treat it as a practical limit rather than a law.
At your home, the shell usually comes off the truck by crane, lifted over the house or fence. Check overhead power lines, street parking, trees and HOA rules. Some cities require a right-of-way or street use permit for a crane in the street. See fiberglass pool cost and installation.
Why do most Texas and Florida builders sell concrete pools?
We did not find a dated market-share survey for Texas or Florida, so we cannot give percentages. The reasons builders commonly give are practical: concrete can be shaped to any lot, works around rock, allows custom depths and features like tanning ledges and swim-up benches anywhere, and supports a large local network of shotcrete, tile and plaster crews. Warm climates also let builders work most of the year. Fiberglass has grown in popularity because it is fast and low-maintenance. Vinyl is more common in colder states.
Which pool type is fastest to install?
Fiberglass is usually fastest. Fixr says the shell installation takes a few days once the shell is on site, and the whole process from ordering to finish takes a few weeks. Vinyl is generally faster than concrete. Concrete takes the longest because of curing; Fixr's 2025 guide gives 3 to 12 weeks for installation. Permits, HOA approval, weather and inspections add time for every type. See the pool construction timeline.
Which pool type is best for resale value?
We could not find a verified study showing that one pool type adds more home value than another in Texas or Florida. What appraisers and buyers tend to look at is condition, age of the surface and equipment, safety features and permits. A well-kept pool of any type, with a recent finish and records, is easier to sell than a neglected one. A liner near the end of its life or plaster that is rough and stained is a negotiating point for buyers. See does a pool add home value?
What about above-ground and semi-inground pools?
Above-ground pools cost far less and can be removed. Fixr's 2024 guide notes hard-sided kits with pump and filter can be under $7,000. Semi-inground pools are partly buried, often with a deck built around them. Fixr's 2025 fiberglass guide lists partially above-ground fiberglass installs at $15,000 to $35,000.
Rules still apply. In Florida, any residential pool over 24 inches deep, including above-ground and on-ground pools, is covered by chapter 515. An above-ground pool's walls may serve as the barrier if they meet 515.29, and its ladder or steps must be removable, lockable or fenced. Texas cities that regulate pools apply their adopted code. See above-ground pools.
What interior finishes go on a concrete pool, and how long do they last?
A concrete shell is waterproofed and finished on the inside. Fixr's January 2025 concrete pool guide gives these figures, labor included:
| Finish | Cost per sq ft (Fixr, 2025) | Life noted by Fixr |
|---|---|---|
| Plaster | $1.50 to $5 | Roughly 5 to 10 years |
| Paint | $1.50 to $5 | Repaint every 2 to 4 years |
| Tile | $4 to $30 | Not stated; full tile interiors are the premium option |
Fixr's page did not price quartz or pebble finishes, which are aggregate blends used across Texas and Florida. Ask builders to price them as separate options and to state the plaster or aggregate product in the contract. Plastering of pools is covered by a national standard, ANSI/PHTA/ICC/NPC-12 2025, the American National Standard for the Plastering of Swimming Pools and Spas, listed by the Pool and Hot Tub Alliance (PHTA). Asking whether your plaster crew follows it is a fair question.
Five questions to ask any builder about pool type
- Which type do you recommend for my exact lot, and why? What would change your mind?
- What do you know about the soil, rock and groundwater on my street?
- What will I need to replace or resurface in the first 20 years, and roughly when?
- If I want a salt system, a heater or automation, does the type change what equipment or wall material I need?
- Do you build all three types? If you build only one, how do you answer buyers whose yard suits another type better?
A builder who only sells one type may still give good advice, but you should hear the trade-offs from more than one source.
How to decide: a short decision guide
- Rocky lot, sloped lot, unusual shape, or you want a custom depth: concrete.
- You want the fastest build and lowest surface upkeep, and a stock shape fits your yard and crane access: fiberglass.
- You want the lowest first cost and accept liner replacements: vinyl.
- High water table in South Florida: any type can work, but ask every builder for a written dewatering and hydrostatic relief plan.
- Expansive clay in DFW or Houston: ask every builder about steel, backfill, deck joints and drainage, and whether they want a soil report.
Then compare licensed builders. In Florida, the pool must be built under a pool/spa contractor license regardless of type. See how to choose a pool builder.
How to choose a provider
- Check your soil (rock, clay or sand) and groundwater before choosing a type.
- Measure crane and truck access if you want fiberglass.
- Ask concrete builders about nozzle operator certification, strength and curing.
- Ask fiberglass builders about backfill, dewatering and filling during install.
- Ask vinyl builders about wall material, liner thickness and liner cost.
- Compare 20-year costs, not just starting prices.
- Get the hydrostatic relief and draining instructions in writing.
Related swimming pool builders and contractors guides
- How Much Does an Inground Pool Cost in Texas and Florida in 2026?
- Fiberglass Pool Cost and Installation: What Texas and Florida Buyers Should Know
- How a Concrete (Gunite) Pool Is Built: Step-by-Step From Layout to First Swim
- How Much Does Pool Resurfacing Cost, and Which Finish Is Right: Plaster, Quartz, Pebble or Tile?
- Above-Ground and Semi-Inground Pools: What Do They Cost, and Do They Need a Permit or Fence in Texas and Florida?
- Is a Pool Crack Serious? Surface Crazing vs Structural Cracks, Causes, Repairs and Your Legal Options in Texas and Florida
- How to Choose a Pool Builder in Texas or Florida: 25 Questions to Ask
Swimming pool builders and contractors by state and city
Questions people ask
Which pool type is best for Florida?
There is no single best type. Concrete is most flexible for shapes and screen-enclosed patios, fiberglass is fast and smooth, and vinyl is lowest in first cost. Florida's key issue is groundwater: Florida Building Code requires hydrostatic relief in areas of anticipated water table, and fiberglass and vinyl pools must be filled on installation. Ask each builder how they control groundwater during the build and later, and never drain any pool without professional guidance.
Which pool type is best for Texas?
On rocky Hill Country lots, concrete is usually easier because it can follow the hole the rock allows. On expansive clay in Dallas and Houston, all three can work if the builder designs for movement with good backfill, steel, drainage and deck joints. Hail country owners with vinyl should think about liner and cover damage. Get bids for at least two types and compare 20-year costs.
How often does a vinyl liner need replacing and what does it cost?
Fixr's January 2025 guide says liners must be replaced every 5 to 9 years, at about $3,000 to $6,000 on average, and notes the walls can last indefinitely. Liner life depends on sun exposure, chemistry, thickness and damage from pets or debris. Keeping pH and chlorine in range and the water level up helps a liner last. Thicker liners resist tears better but cost more.
Can a fiberglass pool be refinished?
Yes. When gelcoat fades, blisters or wears after many years, it can be resurfaced. Fixr's 2025 fiberglass guide lists complete gelcoat resurfacing at $10,000 to $20,000. The work involves draining, which raises groundwater risk in Florida and wet parts of Texas, so it should be done by a licensed pool contractor who checks groundwater and plans for it. In Florida, refinishing interiors falls within pool/spa contractor and servicing contractor scopes.
Is a shotcrete pool better than a gunite pool?
Not by definition. Both are sprayed concrete. Gunite is dry-mix, with water added at the nozzle; shotcrete is usually wet-mix, delivered premixed. The American Shotcrete Association says dry-mix pool shotcrete should reach at least 4,000 psi at 28 days and recommends at least 7 days of curing. Crew skill, steel placement, rebound control and curing matter more than which process is used.
Do fiberglass pools get too hot in summer?
Pool water temperature depends on sun, air temperature, depth and shade much more than shell material. Light-colored steps and benches feel warm in direct sun, as do many deck surfaces. In Texas and Florida summers, owners of all pool types sometimes run water features or use shade to keep water comfortable. If you heat your pool, a cover saves energy no matter what the pool is made of.
What is the width limit for shipping a fiberglass pool?
TxDMV lists 8 feet 6 inches as the legal load width without a permit. With a permit, loads can be up to 16 feet wide on Interstates, and loads over 16 feet need two escorts. That makes about 16 feet a practical upper width for most shells. This is a transport limit, not a pool law, and it varies by state and route.
Sources
- American Shotcrete Association: Pool FAQs
- PHTA: Find a Standard (ANSI pool and spa standards list)
- Fixr: Concrete (Gunite) Pool Cost (updated Jan. 31, 2025)
- Fixr: Fiberglass In-Ground Pool Cost (updated Jan. 31, 2025)
- Fixr: Inground Vinyl Liner Pool Cost (updated Jan. 31, 2025)
- Fixr: Cost to Build a Swimming Pool (updated Jan. 25, 2024)
- Fixr: Pool Remodeling Cost (updated Jan. 31, 2025)
- TxDMV: Texas Size and Weight Limits
- TxDMV: Escort and Equipment Requirements
- Florida Building Code, Residential (2023, 8th ed.) Chapter 45: Private Swimming Pools
- Fla. Stat. Chapter 515 (2026): Residential Swimming Pool Safety Act
- Fla. Stat. 489.105 (2026): Definitions (pool/spa contractor scopes)
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


