Local Guide · Roofing
Florida Building Code for Roofs: HVHZ, Miami-Dade NOAs, and the 2026 9th Edition Changes
A plain-English guide to the rules behind every Florida roof: the High-Velocity Hurricane Zone, product approvals, mandatory reroof upgrades, the 25% rule, uplift testing, and what changes when the 9th Edition takes effect.
The Florida Building Code sets statewide roofing rules, with stricter High-Velocity Hurricane Zone (HVHZ) sections that apply only in Miami-Dade and Broward counties. Roofing products need a Florida Product Approval or, in the HVHZ, typically a Miami-Dade Notice of Acceptance. Every single-family reroof needs a secondary water barrier and stronger deck nailing. The state has scheduled the 9th Edition (2026) to take effect December 31, 2026 (Tampa's notice says January 1, 2027), and tightens tile underlayment, flashing and coastal fastener rules. The code edition on your permit application date controls.
Key facts
- The 'High Velocity Hurricane Zones' sections of the Florida Building Code apply only to Miami-Dade and Broward counties (IIBEC article by a Miami-Dade roofing specialist; Engineering Express).
- The Florida Building Code, 8th Edition (2023) took effect December 31, 2023; the 9th Edition (2026) is scheduled for December 31, 2026 (Florida Building Commission); the City of Tampa's notice says January 1, 2027.
- The code edition in effect on the date of a permit application governs the work for the life of the permit (Fla. Stat. 553.73, as quoted by Greenberg Traurig).
- Under the 9th Edition HVHZ rules, every underlayment used under roof tile must have product approval with uplift resistance; the prescriptive 'yellow stripe' allowance is gone (Miami-Dade RER memo).
- Starting with permits applied for on or after January 1, 2027, HVHZ hip and ridge shingles must be tested to UL 2375 modified to 110 mph, with labeled packaging (Miami-Dade RER memo).
- New FBC Section 1711 sets corrosion-resistance rules for fasteners, connectors and plates within 3,000 feet of a saltwater coastline (Greenberg Traurig; FRSA).
- Every site-built single-family reroof must include a secondary water barrier and improved roof-deck attachment (Fla. Stat. 553.844(3)).
- Roof-to-wall connections are required on reroofs only for homes in the wind-borne debris region insured or valued at $300,000 or more, and only if gable ends or corners can be done for 15% of the reroof cost (Fla. Stat. 553.844).
What is the HVHZ in Florida?
HVHZ stands for High-Velocity Hurricane Zone. Despite the name, it is not a wind map. It is the label for special sections of the Florida Building Code that apply only in Miami-Dade and Broward counties. A Miami-Dade County roofing specialist explained it this way in a professional journal: the term is "merely a title that was chosen for those sections of chapters that contain specific and more stringent requirements," and "by definition" it refers only to Miami-Dade and Broward. An engineering firm's current guide adds that the HVHZ does not include Monroe County (the Keys), even though the Keys face severe hurricane risk.
The HVHZ rules grew out of the South Florida Building Code that Miami-Dade and Broward tightened after Hurricane Andrew in 1992. When Florida adopted a single statewide code, those counties kept their stricter rules as the HVHZ sections. For roofing, the key HVHZ sections are 1512 through 1525 of the Building volume, plus a separate book called the Test Protocols for High-Velocity Hurricane Zones, which contains:
- RAS (Roofing Application Standards): detailed installation rules, such as RAS 115 for asphalt shingles and RAS 118, 119 and 120 for tile.
- TAS (Testing Application Standards): test methods, such as TAS 106 for field checks of tile bonding and TAS 124 for field uplift tests of membrane roofs.
Outside Miami-Dade and Broward, roofs follow the statewide Chapter 15 rules (Building volume) or Chapter 9 (Residential volume). Those are strong rules too; FRSA calls Florida's code the nation's toughest. But they offer more product and installation choices.
Do Broward roofs need Miami-Dade approval? Broward is in the HVHZ, so roofing products used there must meet HVHZ requirements. In practice that usually means a Miami-Dade Notice of Acceptance (NOA) or a Florida Product Approval that specifically covers HVHZ use. Miami-Dade's NOAs say they are accepted "to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction." Your Broward building department is that authority. Ask what it accepts.
What is a Miami-Dade NOA, and how is it different from a Florida Product Approval?
Florida does not let builders use just any roofing product. Each product must be approved for use under the code. There are two main paths.
| Florida Product Approval (FL number) | Miami-Dade Notice of Acceptance (NOA) | |
|---|---|---|
| Who issues it | Florida Building Commission, through floridabuilding.org | Miami-Dade County Department of Regulatory and Economic Resources (RER), Product Control Section |
| Where it applies | Statewide; an approval may also list HVHZ use if tested for it | Miami-Dade, and other jurisdictions that accept it |
| What it looks like | A number such as FL 12345.1 (the number after the decimal identifies the specific product or configuration) | A number such as 24-0625.12, with approval and expiration dates |
| Where to look it up | floridabuilding.org Product Approval search, by FL number or manufacturer and code version | Miami-Dade product control search on miamidade.gov |
An NOA spells out exactly how a product may be used: which deck types, which fasteners, and the maximum design pressure it can resist. One sample NOA for a single-ply TPO roof system over wood decks listed a maximum design pressure of -67.5 pounds per square foot (the minus sign means uplift). The NOA is valid until its expiration date, and it ends early if the materials, use or manufacturing change. Products must carry a "Miami-Dade County Product Control Approved" label, and a full copy of the NOA must be at the job site for the inspector.
How do I check if a product's NOA or FL approval is current?
- Get the exact number from your contract or permit application. Charlotte County, for example, asks for the full FL number including the digits after the decimal.
- Look it up: Florida approvals at floridabuilding.org (Product Approval search), NOAs on Miami-Dade's product control search.
- Check the expiration date and the code edition it was approved under. The sample NOA above showed an expiration of December 17, 2025, so it would need renewal to be used after that.
- Check that the approval covers your deck type, roof slope and design pressure. Your roofer or the building department can tell you the design pressure your roof needs.
Can I use any shingle in Miami-Dade? No. Shingles used in the HVHZ must have an approval for HVHZ use and be installed per RAS 115 or the approval. From January 1, 2027, Miami-Dade says asphalt shingle permits must also use hip and ridge shingles tested to UL 2375 at 110 mph, or follow a prescriptive attachment method with roof cement spots.
What wind speed must a Florida roof withstand?
There is no single number. The required strength depends on your exact location, the building's risk category (most homes are Risk Category II), its height, the surrounding terrain (exposure category), and which part of the roof you are looking at. Corners and edges see much higher uplift than the middle of the roof.
Florida's code uses the national standard ASCE 7-22 for wind loads. Florida adopted it with the 8th Edition at the end of 2023, and the 9th Edition keeps it. According to a 2026 analysis by a Florida construction law firm citing the Florida Building Commission's ASCE 7-22 fact sheet:
- Design wind speeds went up in the western Panhandle for most building categories; speeds across the peninsula were unchanged.
- The ATC Hazard by Location website does not support ASCE 7-22 and can't be used for Florida code compliance. Use the ASCE 7 Hazard Tool or the official code maps.
- For gable and hip roofs steeper than 7 degrees, ASCE 7-22 went back to three roof pressure zones (Zone 1, 2 and 3), lowering design pressures in many zones.
For a sense of scale, the 2026 HVHZ tile installation standard (RAS 127) includes ready-made tables for a 175 mph design wind speed on Risk Category II homes, which shows the level South Florida roofs are designed for. Shingles are rated in wind classes: ASTM D7158 Class D, G and H correspond to design wind speeds of 115, 150 and 190 mph, and the code requires shingle wrappers to show the class. Ask your roofer to show you the design wind speed and pressures used for your permit.
What does Florida require on every reroof? (Fla. Stat. 553.844)
Since 2007, Florida law has required certain wind-mitigation upgrades whenever a site-built single-family home gets a new roof. The Florida Building Commission put them into the code, mainly in the Existing Building volume, Section 706.
| Requirement | Applies to | What it means |
|---|---|---|
| Secondary water barrier (SWR) | Every site-built single-family roof replacement | A sealed layer, such as self-adhered tape over deck seams or a full self-adhered underlayment, so water stays out if the roof covering blows off. IBHS says every inch of rain on an exposed deck can let in water equal to about 9 bathtubs. |
| Improved roof-deck attachment | Every site-built single-family roof replacement | Re-nailing the plywood or boards to the rafters or trusses with more or better nails. IBHS found switching to 8d ring-shank nails at tighter spacing can double a deck's uplift resistance. |
| Roof-to-wall connections (straps or clips) | Homes in the wind-borne debris region with an insured value, or if uninsured a just value, of $300,000 or more | Strengthening where the roof framing meets the walls, but only if the gable ends or all corners can be done for 15% of the reroof cost. Gable ends get priority unless the hip is more than 1.5 times wider. |
Does the code require hurricane straps when re-roofing? Only in that third case, and only within the 15% cost cap. If the work can't be done within the cap, it isn't required. The code offers prescriptive retrofit options so an engineer isn't always needed. Florida's definition of a roofing contractor now includes evaluating and enhancing roof-to-wall connections during a roof job, so your roofer can do it.
These upgrades can earn wind mitigation insurance discounts. Make sure your roofer documents them with photos and the permit inspection, and get a wind mitigation inspection afterward. The My Safe Florida Home program may help pay for these items when it is funded.
What is the 25% rule, and what is the 2007 code cutoff?
The Florida Existing Building Code (Section 706.1.1) has long said that no more than 25% of a roof or roof section may be repaired, replaced or recovered in any 12-month period unless the entire roof or section is brought up to current code. In practice, that meant a storm that damaged a third of an old roof could force a full replacement.
In 2022, the Legislature changed that with SB 4-D, now Fla. Stat. 553.844(5). If the roof or roof section was "built, repaired, or replaced in compliance with the requirements of the 2007 Florida Building Code, or any subsequent editions," and 25% or more is being repaired, only the repaired part must meet current code. Local governments may not amend this exception.
The cutoff date is disputed. Citizens Property Insurance's adjuster guide treats the 2007 code as effective March 1, 2009, so it applies the exception to single-family roofs with a permit application date of March 1, 2009 or later. A 2021 petition to the Florida Building Commission (DS 2021-039) argued for roofs permitted after October 1, 2005, but it came before the 2022 law and commission staff disagreed with it. Your permit history decides which side you fall on, so look it up. See our permit lookup guide.
A "roof section" is a part of the roof separated by expansion joints, parapet walls, flashing (not valleys), elevation changes (not hips or ridges), a change in roof type, or a legal description. This matters for condos and townhomes, where one building's roof may contain several sections. For how insurers apply the rule and Florida's matching law, see our matching law guide.
What is a roof uplift test?
An uplift test checks whether a roof component will stay attached when wind pulls up on it. Some are lab tests done before a product gets approved. Others are done on your actual roof. In the HVHZ, the field tests homeowners and boards most often hear about are:
- TAS 106: a field check of the bond on mortar-set or adhesive-set tile (and, in the 9th Edition, some mechanically attached rigid systems). The HVHZ code text has required a field verification and static uplift test of adhesive-set and mortar-set tile after installation and before final inspection, with results sent to the building official. The 9th Edition updates the test to use ASCE 7 zone names (Zone 1, 2 and 3) when deciding how many tiles to test.
- TAS 124: a field uplift test for existing membrane roofs and in-place testing for reroof and new roofs. The HVHZ code has required it when a new roof will be bonded to an existing membrane, and the building official may request it as a quality-control test on continuous roof systems.
- TAS 105: a fastener pull-out test, for example when an existing steel deck is thinner than 22 gauge.
Lab tests matter too. Under the 9th Edition, tile underlayments must be tested for uplift (FM 4474 or UL 1897), and the result must be part of the product approval. FRSA explains the industry push for this: performance "must be measurable, not assumed."
If your contractor says a test is needed, ask who performs it, what it costs, and that the results be given to you and the building department. Commercial and condo boards should require test results in the closeout file. See our commercial roofing guide.
What changes in the 2026 Florida Building Code (9th Edition) for roofing?
When it takes effect
The Florida Building Commission has scheduled the 9th Edition to take effect December 31, 2026. Sources disagree on the exact start: the City of Tampa's notice says January 1, 2027, and Miami-Dade applies its new product rules to permits applied for on or after January 1, 2027. Miami-Dade RER also said online portal submissions after 4 p.m. on December 30, 2026 fall under the new edition. Because the edition in effect when you apply governs the whole permit, a roof permit applied for in late December may follow different rules than one applied for in early January. Ask your building department for its cutoff.
The roofing changes that matter most
| Change | Where | What it means for owners |
|---|---|---|
| All tile underlayments must have product approval with tested uplift resistance | HVHZ (and statewide testing push) | Fewer, more documented underlayment choices under tile; the prescriptive "yellow stripe" option is gone in the HVHZ. |
| Tile fasteners must penetrate through the sheathing or at least 3/4 inch into it, even with battens | HVHZ tile standards RAS 118, 119, 120 | Stronger attachment; may change installation methods. |
| Hip and ridge shingles tested to UL 2375 at 110 mph, with labeled packaging, or a prescriptive cement-spot method | HVHZ | Ridge caps are a common failure point in storms; this targets them. |
| Corrosion-resistant nails, screws, fasteners and connectors near saltwater (new Section 1711) | Statewide, within 3,000 feet of a saltwater coastline (300 feet for some screws) | Coastal homes may need stainless or heavier galvanized fasteners. |
| Flashing required at roof edges, penetrations and changes of roof covering type, in addition to walls, gutters and slope changes; hip and ridge exception now limited to steep-slope non-metal coverings | Statewide | Fewer gaps at edges and transitions. |
| Drip edge required at eaves and gables of steep-slope roofs (2:12 and above) | Statewide | Better edge protection, a known weak point in high winds. |
| Recover vs. replace: tear-off still required with 2 or more coverings or a wet or deteriorated roof, but a sound substrate such as high-R insulation or lightweight insulating concrete may stay when upper layers come off; adhered deck membranes may remain | Existing Building volume, statewide | Can save money on flat and commercial roofs; document substrate condition. |
| Coatings over asphalt shingles must follow the shingle maker's approved instructions | Statewide | Roof coatings sold to "extend" shingle roofs face clearer limits. |
ASCE 7-22 wind loads stay the same in this edition, so FRSA says the FRSA-TRI Florida High Wind Concrete and Clay Roof Tile Installation Manual (Seventh Edition) tables are unchanged. A 2026 bill (HB 911) that would have required 160 mph impact-resistant envelopes in some areas died in committee on March 13, 2026.
These summaries come from Miami-Dade RER, FRSA and law-firm analyses of the approved changes. The final published code governs, so confirm details with your building official.
What can't you do on a Florida reroof?
Under the Existing Building code's "recovering versus replacement" section, you must tear off all layers down to the deck if:
- The existing roof covering or system is water-soaked or too deteriorated to serve as a base.
- The existing covering is wood shake, slate, clay, cement or asbestos-cement tile.
- The roof already has two or more coverings.
- Blisters exist, unless they are cut open and secured first.
- The existing covering would be used to attach the new roof and the code's securement rules can't be met.
Exceptions include separate structural systems such as standing-seam metal that carry their loads directly to the framing. In the HVHZ, Sections 1512 through 1525 apply instead. Since the mandatory secondary water barrier and deck renailing require access to the deck, most residential shingle and tile reroofs in Florida are full tear-offs anyway. See our deck and underlayment guide.
What should condo boards and property managers watch?
- Time your permit application. A large reroof bid in late 2026 under 8th Edition assumptions may not match a 9th Edition permit. Ask bidders which edition they priced and put it in the contract.
- Demand the paperwork: product approvals or NOAs for every component, design pressure calculations, test results (TAS 106 or TAS 124 where used), and inspection approvals.
- Check roof sections for the 25% rule and confirm the permit history of each section.
- Coastal buildings within 3,000 feet of saltwater should confirm the new corrosion rules are in the specification.
- Link to your reserve study. The roof is a required item in Florida's structural integrity reserve study for condo buildings three habitable stories or higher. See our condo and HOA roof guide.
This guide is general information, not engineering or legal advice. For a specific building, consult a Florida-licensed engineer or architect, your building official, or a construction attorney.
How to choose a provider
- Find out whether your home is in the HVHZ (Miami-Dade or Broward) or under statewide rules.
- Ask your roofer for the design wind speed and pressures used on the permit.
- Get the FL Product Approval or NOA number for every roof component in the contract.
- Look up each approval and check its expiration date and code edition.
- Confirm the bid includes the secondary water barrier and deck renailing.
- If your home is in the wind-borne debris region and insured at $300,000 or more, ask about roof-to-wall work within the 15% cap.
- Look up your roof's permit history before relying on the 25% rule exception.
- If you live within 3,000 feet of saltwater, ask about Section 1711 corrosion-resistant fasteners.
- Ask which code edition your permit application will fall under near the December 2026 transition.
- Keep photos, product labels, test results and inspection approvals for insurance and resale.
- Schedule a wind mitigation inspection after the new roof is finished.
Related roofing guides
- Do I Need a Permit to Replace My Roof? Texas and Florida City-by-City Basics
- Florida Wind Mitigation Inspection: How Do Roof Credits Work, Question by Question?
- Florida's Matching Law: Will Insurance Replace the Whole Roof if Shingles Don't Match?
- Tile Roofs in Florida: Is It the Tile or the Underlayment, and What Do Re-Roofs Involve?
- What's Under Your Shingles: Decking, Underlayment, Secondary Water Barrier and Ventilation Explained
- HOAs, Condos, and Roofs: Who Pays, Who Decides, and Florida's New Reserve Rules
- My Safe Florida Home: Can a Grant Pay for Your New Roof?
- What Is the Best Roofing Material for Florida: Shingles, Tile or Metal?
Roofing by state and city
Questions people ask
Is Palm Beach County in the HVHZ?
No. The HVHZ sections apply only to Miami-Dade and Broward counties. Palm Beach and other coastal counties follow the statewide Florida Building Code roofing chapters, which are still strict and based on ASCE 7 wind loads. Products there need a statewide Florida Product Approval or another approval the building department accepts.
Does my old roof have to meet the new code if it isn't damaged?
No. The building code applies when you get a permit for new work. An existing roof doesn't have to be upgraded just because the code changed. But insurers may look at roof age and condition, and when you replace or substantially repair the roof, the new work must meet the code in effect on your permit application date.
What is the difference between a re-cover and a replacement?
The Florida code defines roof recover as installing a new covering over a prepared existing covering without removing it, and roof replacement as removing the existing covering, repairing the substrate and installing a new covering. Re-covers are not allowed in many situations, including over tile or when two coverings already exist. On homes, the required deck upgrades usually make replacement the practical choice.
Who checks that my roofer followed the code?
Your local building department, through the permit and inspections. Many Florida departments use an in-progress inspection or a re-roof inspection affidavit for deck nailing and the secondary water barrier, then a final inspection. In the HVHZ, field test results may also be required. Keep copies of every approval.
Can a roof coating replace a new roof in Florida?
Not as a way around a required replacement. The 2026 code moves shingle coating rules into the asphalt shingle sections and requires coatings to follow the shingle manufacturer's approved instructions. A coating does not reset your roof's age for insurance purposes. Florida measures roof age from the last time 100% of the roof was replaced to the code then in effect.
Where can I read the actual Florida Building Code?
The Florida Building Commission links to the official code books and its Analysis of Changes documents from floridabuilding.org. The Analysis of Changes for the 9th Edition compares old and new sections side by side. For a specific question, your local building official is the authority that interprets the code for your permit.
Do I need an engineer for my roof in Florida?
Most single-family reroofs don't need one, because the code provides prescriptive methods and product approvals list design pressures. You may need an engineer or architect for unusual designs, calculations beyond the RAS tables, some roof-to-wall retrofits, commercial roofs, and condo projects. Condo structural integrity reserve studies and milestone inspections are done by engineers, architects or credentialed reserve specialists.
Sources
- IIBEC (Michael L. Goolsby): The Florida Building Code, High Velocity Hurricane Zones and the Registered Roof Consultant (2001)
- Engineering Express: What is the HVHZ in Florida?
- Florida Building Commission: Building Codes page
- Florida Building Commission: 2026 FBC Workplan (June 2026)
- Florida Building Commission: Analysis of Changes, 9th Edition (2026) Test Protocols for the HVHZ
- Florida Building Commission: HVHZ Chapter 15 text (2010 supplement)
- Florida Building Commission: Product Approval search
- City of Tampa: New Florida Building Code 9th Edition announcement
- Greenberg Traurig: New Florida Building Code Edition Takes Effect Dec. 31, 2026 (Nov. 2026)
- Jimerson Birr: Florida Building Code Tightens Up: New Wind-Resistance Rules for Roofing (June 2026)
- Miami-Dade RER Product Control: 9th Edition FBC roofing underlayment memo
- Miami-Dade RER Product Control: 9th Edition FBC hip and ridge shingles memo
- Miami-Dade NOA No. 24-0625.12 (sample single-ply roof system NOA)
- Miami-Dade RER: NOA application (definitions)
- FRSA (Mike Silvers): Changes in the 2026 9th Edition of the Florida Building Code (Feb. 2026)
- FRSA (Mike Silvers): Additional Changes in the 2026 Ninth Edition of the FBC (March 2026)
- FRSA (Manny Oyola Jr.): Tile Changes in the 2026 Ninth Edition Florida Building Code (April 2026)
- FRSA: New 2023 FBC Eighth Edition is Now in Effect
- Fla. Stat. 553.844 (2026): Windstorm loss mitigation; roofs
- Fla. Stat. 553.73 (2026): Florida Building Code
- Fla. Stat. 489.105 (2026): Definitions (roofing contractor)
- Fla. Stat. 627.7011 (2026): Homeowners' policies (roof age)
- Citizens Property Insurance job aid: Evaluating Roof Damage, 25% Rule
- Florida Building Commission: DS2021-039 staff analysis (25% rule petition)
- Professional Roofing (NRCA), Mark S. Graham: Understanding asphalt shingle standards (2021)
- IBHS FORTIFIED: FORTIFIED Roof
- Charlotte County, FL: Residential Roof permits
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


