New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Roofing

Commercial Roofing Guide for Building Owners: Which System, How Long It Lasts, and How to Budget

An owner-side guide to low-slope roofing systems, recover limits, wind ratings, NDL warranties, consultants and capital planning, with the Texas and Florida rules that change the answer.

There is no single best commercial roof. TPO, PVC, modified bitumen, built-up, spray foam, metal and coatings each fit different buildings. Plan for inspections twice a year, a written asset plan and a yearly reserve. Codes generally allow only one recover before a full tear-off, Florida requires licensed roofers and permits, and FM ratings such as 1-90 measure uplift pressure, not wind speed.

Key facts

  • Florida's Existing Building code (706.3) requires tear-off to the deck when a roof already has two or more coverings, is water-soaked, or has slate, tile or wood shake.
  • The 9th Edition (2026) Florida code adds an exception letting an adequate existing substrate, such as high-R insulation or lightweight insulating concrete, remain when upper layers are removed.
  • FM Approvals ratings (1-60, 1-90, 1-120) are uplift pressures in psf tested in 15 psf steps from 30 psf, with a 2-to-1 safety factor, not wind speeds.
  • Texas uses the 2012 International Building Code as the default commercial code in cities, with local adoption of newer editions allowed.
  • IIBEC, the roof consultants' body, was founded in 1983 as the Roof Consultants Institute and renamed IIBEC on April 1, 2019.
  • NDL means No Dollar Limit: covered repairs have no dollar cap, but exclusions such as storms and ponding still apply.
  • Florida commercial reroofs need a permit; the 2026 under-$7,500 permit exemption applies only to single-family homes.
  • Texas owners must retain 10% of the contract price for 30 days after completion under the mechanic's lien law.
  • Florida condo budgets must reserve for roof replacement, and buildings of 3+ habitable stories need a structural integrity reserve study every 10 years.

What makes a commercial roof different from a house roof?

Most commercial buildings have low-slope roofs, often called flat roofs, even though they are built with a slight pitch toward drains. Instead of overlapping shingles that shed water, a low-slope roof relies on a continuous waterproof membrane. That changes almost everything an owner has to think about: how water drains, how the roof is held down in wind, who designs it, what the warranty covers, and how the cost is planned and taxed.

The roof is also usually one of a building's largest single capital expenses. For an owner or property manager, the job is not only to fix leaks. It is to know the roof's condition, predict when it will need major work, and plan the money and the tenant disruption years ahead. This guide explains the systems, the code limits, the wind ratings that insurers ask about, warranties, consultants and budgeting, with Texas and Florida rules where they differ. If you have storm damage right now, start with commercial roof insurance claims.

What are the main commercial roofing systems?

No single system is best for every building. The right choice depends on the deck, the building's use, foot traffic, rooftop equipment, drainage, the wind zone, the insurer's requirements and how long the owner plans to hold the property.

SystemWhat it isWhere it tends to fitWatch-outs
TPO (thermoplastic polyolefin)Single-ply sheet, usually white, seams heat-weldedWarehouses, retail, offices wanting a reflective surfaceSeam quality depends on the crew; thickness and formulation vary by maker
PVCSingle-ply sheet, heat-welded seamsRestaurants and buildings with grease or chemical exhaustUsually costs more than TPO
Modified bitumen (mod bit)Asphalt sheets with polymer modifiers, often in two or more pliesBuildings with foot traffic, smaller roofs, re-roofs over similar systemsTorch-applied versions carry fire risk during installation
Built-up roof (BUR)Layers of felt and asphalt or coal tar, often with gravelOlder and institutional buildingsHeavy; NRCA-attributed life ranges are 12 to 25 years (asphalt) and 12 to 30 (coal tar)
SPF (spray polyurethane foam)Foam sprayed in place, then coatedIrregular roofs, buildings needing added insulationCoating must be maintained and recoated
Metal (standing seam or through-fastened)Metal panels, often on low-slope metal buildingsMetal buildings, owners wanting long service lifeEdge and fastener corrosion near salt water; cosmetic hail dents
Coatings (acrylic, silicone and others)Liquid applied over an existing roofExtending a sound roof that is not wetNot a fix for a saturated or failed roof

For deeper detail on membranes, see the flat and low-slope roof guide. For metal, see the metal roof guide. For energy effects of white membranes and coatings, see cool roofs.

Market data shows how these systems are moving. The Asphalt Roofing Manufacturers Association reported that U.S. modified bitumen shipments fell 13.8% year over year to 9.1 million squares in the first quarter of 2026, and built-up roofing fell 16.7%, as reported by Roofing Contractor. Those are market signals, not a ranking of which system is better.

How long does a commercial roof last?

Life depends on the system, the quality of installation, drainage, maintenance and climate. Published ranges differ by source. The NRCA-attributed figures summarized by the USDA Forest Service put asphalt built-up roofs at 12 to 25 years, coal-tar built-up roofs at 12 to 30 years and sheet metal at 20 to 50 years or more. Those figures come from an older, undated summary, so use them as a rough starting point, not a promise.

In Texas and Florida, three things shorten life most often:

  • Ponding water. Water that sits after rain stresses seams and can void some warranties.
  • Heat and UV. Membranes and coatings age faster under strong sun and high surface temperatures.
  • Storms. Hail punctures and bruises membranes and insulation in Texas. Hurricane wind peels roofs at corners and edges in both states.

A useful way to think about life is the warranty term plus the condition. The warranty term tells you what the manufacturer was willing to stand behind. Regular inspection reports tell you whether your roof is aging faster or slower than that. See roof lifespans in Texas and Florida.

Warning signs: when does a commercial roof need attention?

Most commercial roofs fail slowly, and the early signs are cheap to fix. Walk the building inside and out at least twice a year, and after storms, with this list. If you see several of these on the same roof section, call for a professional inspection and ask whether a moisture survey is needed.

Inside the building

  • Stained or sagging ceiling tiles, especially under drains, rooftop units and roof edges. Mark each stain on a floor plan with the date, so you can tell an old stain from a new leak.
  • Drips that show up only in wind-driven rain. These often point to edge metal, wall flashings or rooftop unit curbs rather than the open field of the membrane.
  • Musty smells or mold in upper floors or warehouse racks, which can mean water is soaking the insulation without dripping through.
  • Rust or staining on the underside of a steel deck, or soft spots in a wood deck that you can see from below.

On the roof (only with safe access)

  • Water still standing two days after rain. The industry test, explained in the flat roof guide, is no ponding 48 hours after a rain in drying weather.
  • Clogged drains, scuppers and gutters, plus leaves, plant growth or debris around them.
  • Blisters, wrinkles, open seams or splits in the membrane, and spongy areas that give underfoot, which can mean wet insulation below.
  • Loose, bent or missing edge metal and copings. Wind failures usually start at the edges and corners.
  • Screws, panels and tools left by other trades, and new penetrations no one told you about.
  • Bare spots in a coating or gravel surface, or granule loss on a modified bitumen cap sheet.

Write each finding down with a photo. A pattern of small problems on one section is often the first sign that the section is near the end of its life, and that record is what a consultant needs to tell you whether to repair, coat, recover or replace. See common roof problems.

Recover or tear-off: when can you put a new roof over the old one?

A recover means installing a new roof covering over the existing one. A tear-off (replacement) removes the old roofing down to the deck. Recovering saves demolition and disposal cost and keeps the building more weather-tight during work. But codes limit it, and a recover over a wet roof traps water in the insulation.

Florida's rule

The Florida Building Code, Existing Building, Section 706.3 requires tear-off down to the deck when any of these conditions exist:

  1. The existing roof covering or components are water-soaked or deteriorated so they are not an adequate base.
  2. The existing covering is wood shake, slate, clay, cement or asbestos-cement tile.
  3. The roof already has two or more applications of any type of roof covering.
  4. Blisters exist, unless they are cut or scraped open and secured first.
  5. The existing covering would be used to attach the new system and cannot meet the code's securement provisions.

Exceptions include complete separate systems, such as a standing-seam metal retrofit that carries loads to the structure, and a new protective coating over an existing spray foam roof. The 9th Edition (2026) code adds an exception that lets an adequate existing substrate, such as high-R insulation or lightweight insulating concrete, stay in place when the upper layers are removed. Buildings in the High-Velocity Hurricane Zone (Miami-Dade and Broward) follow separate HVHZ sections.

Texas

Texas sets the 2012 International Building Code as the default commercial building code inside cities, and cities may adopt newer editions with local amendments. The IBC has its own recovering-versus-replacement section along the same lines, including limits when two coverings already exist. Ask your city building department which edition applies before you plan a recover.

The practical test

Before any recover, get a moisture survey (infrared, nuclear or core cuts) to find wet insulation. If a large share is wet, the savings from recovering usually disappear. Also confirm that the new system's wind uplift rating can be met when fastened through the old layers.

Florida's 25% rule can also force a whole roof section to current code if more than 25% is repaired, replaced or recovered in 12 months, unless the roof or section was built, repaired or replaced under the 2007 Florida Building Code or later, in which case only the repaired part must meet current code (Fla. Stat. 553.844(5)). A 2022 law limits that to the repaired portion for roofs built under the 2007 code or later. See Florida code and HVHZ rules.

Should I coat or replace my commercial roof?

A coating can add years to a roof that is dry, well attached and structurally sound. It cannot fix wet insulation, failed attachment or a deck problem. Use this decision path:

  1. Is the insulation dry? If a moisture survey shows widespread wet insulation, coating seals the water in. Replace or recover the wet areas instead.
  2. Is the membrane well attached? Coatings do not add wind uplift resistance to a roof that is coming loose.
  3. Is drainage adequate? Many coatings are sensitive to ponding water, and warranties may exclude it.
  4. What does the code say? In Florida, the code permits a new protective coating over spray foam without tear-off. Coatings over asphalt shingles must follow the shingle maker's instructions.
  5. What warranty will you get? Coating warranties range from material-only to labor-and-material coverage. One coatings maker's warranty FAQ, for example, separates a material-only warranty from two No Dollar Limit tiers and requires annual inspections for the top tier.

Florida's 2026 legislative session saw bills (HB 815 and SB 808) that would have changed roof-age insurance rules and that the Florida Roofing and Sheet Metal Contractors Association said promoted roof coatings. Both died in committee, so no coating mandate became law.

What does a commercial roof cost per square foot?

We could not find a neutral, recent, published survey of commercial roof costs per square foot for Texas or Florida. Most numbers online come from contractors and lead-generation sites that do not explain their methods, so we do not repeat them here. Instead, here is what actually moves the price, so you can read bids critically:

  • Tear-off vs recover. Removal and disposal, especially of heavy gravel built-up roofs, is a large share of cost.
  • Insulation. Energy codes and the owner's goals set the R-value. Tapered insulation to fix ponding adds cost but often pays back in roof life.
  • Wind design. Higher uplift requirements mean more fasteners, adhesive or a heavier system, especially at corners and perimeters.
  • Edges, curbs and penetrations. Each rooftop unit, pipe and skylight is detail work.
  • Access and logistics. Cranes, street closures, night work and occupied buildings add cost.
  • Warranty level. An NDL warranty often requires specific materials, inspections by the manufacturer and an approved installer.
  • Material prices. Construction input prices rose 7% year over year in April 2026, according to an Associated Builders and Contractors analysis of BLS data reported by Roofing Contractor, with energy, steel and imported products leading.

The best cost tool is a consultant's or estimator's line-item budget for your building, updated every year or two. See how to compare roofing bids line by line and what drives roof cost.

What is a roof asset management plan, and how do I budget for replacement?

A roof asset management plan is a simple record that answers four questions for each roof: what is up there, what condition is it in, what will it need and when, and what will that cost. Owners of more than one building use it to avoid surprise replacements and to spread capital spending across years.

What goes in the plan

  • A roof map with each section's area, system type, installation date, contractor and warranty term.
  • Inspection reports with photos, at least twice a year and after major storms.
  • A repair log with dates, costs and who did the work (unauthorized repairs can void a warranty).
  • A condition rating and estimated remaining life for each section.
  • A 5- to 10-year budget with repair, restoration and replacement line items.

A simple budgeting method

Divide the expected replacement cost by the remaining years of life to get a yearly reserve. For example, if a consultant estimates that a roof section will cost $400,000 to replace in about 8 years, the owner would set aside about $50,000 a year, then adjust as inspections change the estimate. This is an illustration, not a price estimate.

Florida condo associations have a legal version of this. Florida law requires condo budgets to carry reserves for roof replacement, and buildings of three or more habitable stories must have a structural integrity reserve study, which includes the roof, at least every 10 years. See HOA and condo roof responsibility.

Taxes and the capital plan

Roofs on nonresidential buildings can qualify for Section 179 expensing, which can change the after-tax cost of replacing in one year versus another. See roof replacement taxes for businesses and talk to your tax adviser before you set the schedule.

How often should a commercial roof be inspected?

The common industry recommendation is at least twice a year, typically spring and fall, plus after any major wind, hail or hurricane event. Warranties often set their own rules. Some manufacturers require yearly inspections and documented maintenance to keep top-tier warranty coverage, so read your warranty and calendar the dates.

A good inspection report includes:

  • Photos of each roof section, drains, edges, flashings and rooftop equipment.
  • Notes on ponding, blisters, open seams, punctures and loose edge metal.
  • Clogged drains and scuppers (a leading cause of ponding and overload).
  • Damage from other trades, such as HVAC technicians leaving screws and panels on the membrane.
  • Recommended repairs ranked by urgency, with rough costs.

After a storm, document damage before repairs and report claims promptly. In Florida, the 1-year notice deadline for property claims (18 months for supplemental claims) applies to any property insurance policy, including commercial policies and surplus lines policies. See the roof inspection guide and the maintenance checklist.

Wind uplift, FM ratings and insurance

Wind does not push a low-slope roof down. It pulls it up. Air moving over the roof lowers the pressure above it while air leaking into the building raises the pressure below it. Corners and perimeters see the highest loads, which is why most wind failures start at the edges.

Code wind design

Building codes require the roof system to resist the design wind pressures calculated for the building's location, height, exposure and roof zones, generally using ASCE 7. In Florida HVHZ counties, roof systems need a Miami-Dade Notice of Acceptance (NOA) or equivalent approval that lists the maximum design pressure. One sample single-ply NOA listed a maximum design pressure of -67.5 pounds per square foot (psf) over wood decks. A full copy of the NOA must be available on the job site. The 2026 Florida code also adds corrosion-resistance rules for fasteners and metal connectors within 3,000 feet of salt water.

What "FM 1-90" actually means

FM Approvals, a unit of the insurer FM Global, tests roof assemblies on a pressure table. The test starts at 30 psf for one minute and steps up 15 psf at a time until something fails. The rating, such as 1-60, 1-90 or 1-120, describes uplift pressure in psf, not wind speed. A 1-90 rating does not mean the roof resists 90 mph winds. FM also applies a 2-to-1 safety factor, so a roof needing 37.5 psf of field resistance calls for a 1-75 assembly.

FM ratings matter most if FM Global insures the building or a lender or tenant lease requires them. They are not a substitute for code wind design. Corners and perimeters need enhanced attachment under FM's data sheets too.

Texas coast

Buildings insured by TWIA in the 14 coastal counties and part of Harris County must meet TWIA's building code and inspection requirements for work done since 1988. Plan for the windstorm inspection and certificate in the schedule. See TWIA windstorm certification.

Insurance terms to check

Commercial property policies vary more than homeowners policies. Before you replace a roof, ask your agent how the policy values the roof (replacement cost or actual cash value), what the wind or named-storm deductible is, and whether a better wind rating or impact-resistant system earns a credit. See commercial roof insurance claims.

Hail, rooftop equipment and solar: what IBHS recommends for commercial roofs

The Insurance Institute for Business and Home Safety (IBHS), an insurer-funded research group, publishes a commercial roof best practices guide. Its advice is not code, but it is a useful checklist for owners in hail-prone North and Central Texas and hurricane-prone coastal Texas and Florida.

Hail (Dallas-Fort Worth, San Antonio, Austin and much of Texas)

  • For flat and low-slope roofs (3:12 or less), IBHS says hail-resistant covers should meet FM Approvals Standard 4470 with a Class 1-SH (Severe Hail) rating or UL 2218 Class 4.
  • FM 4470 is the approval standard for the whole low-slope assembly (cover, insulation and deck). Its minimum hail level is Moderate Hail (MH). IBHS recommends Severe Hail (SH) for hail-prone areas.
  • IBHS recommends a cover board (a thin, hard board under the membrane) in new systems to increase puncture resistance.
  • Hail guards should protect air conditioner condenser fins, fans and other equipment that hail could disable.

Wind (the Texas Gulf Coast and all of Florida)

  • IBHS defines hurricane-prone regions under ASCE 7-10 and 7-16 as Gulf and Atlantic coast areas where the design wind speed for ordinary (Risk Category II) buildings is greater than 115 mph.
  • In those regions, IBHS says stone ballast, ballast pavers and pedestal paver systems should not be used, built-up roofs with loose pea gravel should not be used (gravel fully embedded in asphalt is acceptable), and vegetative (green) roofs should not be installed.
  • Single-ply membranes should have a perimeter peel-stop, such as a termination bar, 1 to 2 feet from the roof edge, unless the system is mechanically fastened in that zone.
  • Edge flashing, copings and counterflashing should comply with ANSI/SPRI/FM 4435/ES-1 for the site's design pressures.
  • Rooftop units, curbs and other structures should be designed and fastened for ASCE 7 rooftop equipment loads with a safety factor. Loose units turn into debris that tears the membrane.

Solar on a commercial roof

IBHS does not recommend ballasted (weighted, not fastened) solar arrays in hurricane-prone areas. It recommends designing arrays and attachments for ASCE 7-16 or equivalent wind loads, checking that the deck can carry the added load, and leaving enough space between rows for crews to service panels without removing perimeter rows. A new roof under a solar array is far cheaper than removing and reinstalling the array later, so align the roof's remaining life with the solar plan. See roofs and solar panels.

Commercial roof storm claims: the basics

A full walkthrough is in commercial roof insurance claims. The short version for owners and managers:

  • Document before you repair. Photograph the roof, the interior damage and the date. The Texas Department of Insurance advises making only temporary repairs, such as tarps or patches, before the adjuster inspects, because permanent repairs made first can lead to a denial. Keep the receipts.
  • Report fast. In Florida, notice of a property claim must be given within 1 year of the date of loss (18 months for a supplemental claim), and for hurricanes the date of loss is the landfall date. Many Texas policies also set claim deadlines, some as short as one year.
  • Know the Texas presuit rule. For claims from hail, wind, hurricanes and other forces of nature, Texas Insurance Code chapter 542A requires written notice to the insurer at least 61 days before filing a lawsuit, and lets the insurer ask to inspect the property.
  • Read the roof warranty too. IBHS notes that standard roof warranties typically exclude wind damage and that separate wind warranties may be available. Storm damage usually goes to your insurer, not the roof manufacturer.
  • Get your own expert when the numbers are large. A roof consultant or engineer can document damage and scope. In Florida, contractors may not adjust claims or interpret coverage unless they are licensed public adjusters, and in Texas, contractors may not act as public adjusters on property where they do or may do the work.

This is general information, not legal advice. For coverage disputes, contact the Texas Department of Insurance (1-800-252-3439) or Florida's Department of Financial Services (1-877-693-5236), or talk with an attorney or licensed public adjuster.

What is an NDL warranty, and how is it different from a contractor warranty?

Commercial roofs usually carry two kinds of warranty:

WarrantyWho stands behind itWhat it usually covers
Contractor (workmanship) warrantyThe roofing contractorInstallation errors, often for a short term. Only as good as the company's survival.
Manufacturer material warrantyThe product makerDefects in the materials, sometimes prorated. Usually no labor.
Manufacturer system or NDL warrantyThe product makerLeaks from covered material or workmanship defects, labor and material, with no dollar cap within the terms

NDL stands for "No Dollar Limit." It means covered repairs are not capped at a set dollar amount, as long as the problem falls within the warranty's terms. It does not mean everything is covered. Common exclusions include storm damage, ponding water, building movement, damage by others, and repairs by unauthorized workers. Many NDL warranties require an approved installer, a manufacturer inspection at completion, specified materials, and maintenance records.

Questions to ask before you sign:

  • Is the warranty NDL, prorated, or material-only? For how many years?
  • What wind speed, if any, is covered? Is hail covered, and at what size?
  • Which inspections and maintenance does the warranty require?
  • Is it transferable if you sell the building, and at what cost?
  • Who may make repairs without voiding coverage?

See roof warranties explained.

Consultant or contractor: who should design a re-roof?

On a small, simple roof, a qualified contractor can design and install the system. On larger, complex or high-risk buildings, many owners hire an independent roof consultant or architect to write the specification, review bids and inspect the work. The value is independence: the designer does not profit from a bigger or smaller scope.

The main professional body is the International Institute of Building Enclosure Consultants (IIBEC). It was founded in 1983 as the Roof Consultants Institute, became RCI, Inc. in 2006, and took the IIBEC name on April 1, 2019. Its credentials include the Registered Roof Consultant (RRC). In Florida, roof consultants who design or certify work may need to be licensed engineers or architects, so ask.

A good specification covers the system, attachment for each wind zone, insulation and slope, flashing details, the warranty required, testing, inspection points and the schedule. A good bid process sends the same specification to several qualified contractors so their prices compare. See how to choose a roofing contractor.

What happens during a commercial re-roof, step by step

A commercial re-roof is a construction project, not a one-day job. Knowing the sequence helps you check that nothing is skipped.

  1. Survey and testing. A consultant or estimator measures the roof, takes core samples, and runs a moisture survey to map wet insulation. On older buildings, ask whether materials should be tested for asbestos before tear-off.
  2. Specification. The scope names the system, attachment for each wind zone, insulation, slope, flashing details, edge metal and warranty.
  3. Bids. IBHS suggests asking every bidder for a statement of work, a schedule with milestones, a site use diagram, manufacturer specifications with approvals (such as Florida Product Approval, Miami-Dade, TDI, UL or FM), a quality control plan, and a bad-weather and emergency plan for securing loose materials.
  4. Contract, permit and notices. In Florida, the permit is pulled and the Notice of Commencement is recorded and posted before the first inspection. In Texas, confirm the city permit and, on the coast, who will handle the TWIA windstorm inspection.
  5. Preconstruction meeting. Agree on work hours, staging, crane days, tenant notices, interior protection and who on your side can approve extra work.
  6. Safety plan. IBHS recommends a designated safety representative on site and written safety plans that follow OSHA fall protection rules. Torch-applied roofing needs a written hot work program because of the fire risk.
  7. Tear-off and dry-in, section by section. Crews remove only what they can cover the same day. SPRI's application guideline for thermoplastic roofs requires a temporary "daily seal" at the end of each day and before bad weather so water cannot run under the finished sections.
  8. Deck inspection and repair. Damaged or rusted deck is replaced at the unit prices in the contract. Ask for photos before anything is replaced.
  9. Insulation, membrane, flashings and edge metal. Flashings at curbs, walls and drains take more time than the open field and cause most leaks if rushed.
  10. Inspections. The building department inspects to the permit. On the Texas coast, a WPI-8 for ongoing construction requires inspections during the work. For an NDL warranty, the manufacturer usually inspects at completion and lists items to fix.
  11. Closeout. Collect the warranty, as-built roof plan, product data, final inspection approval, and lien releases from the contractor, subcontractors and suppliers before final payment. In Texas, hold the required 10% retainage for 30 days after completion.

Avoid scheduling major tear-off during Florida's peak hurricane months if you can. IBHS notes that roof work in hurricane-prone regions can be difficult during hurricane season and that some systems need minimum temperatures to install properly.

Licensing, permits and contracts for commercial roofing in Texas and Florida

Florida. Commercial roofing requires a Florida-licensed roofing contractor (certified or registered) or another license class that covers the work. Check licenses on DBPR's search. A permit is required for reroofing, and the state's 2026 permit exemption for work under $7,500 applies only to single-family homes. For improvements over $2,500, the owner must record and post a Notice of Commencement before the first inspection. Liens follow Chapter 713: subcontractors and suppliers must serve a Notice to Owner, and liens must be recorded within 90 days of final furnishing. See the Florida license lookup and roofing liens.

Texas. There is no state roofing license. The Roofing Contractors Association of Texas offers a voluntary credential, and its commercial track requires $500,000 in general liability coverage (or a bond or letter of credit alternative) plus workers' comp or a filed non-coverage notice. Permits and contractor registration are set by each city. Texas lien deadlines are longer on non-residential projects: an original contractor files by the 15th day of the 4th month after the month work ended. Owners must retain 10% of the contract price for 30 days after completion. See vetting Texas roofers and the roofing contract checklist.

Can I keep my business open during re-roofing?

Usually yes, with planning. The main risks are water entering the building while the roof is open, falling debris, fumes and odors from adhesives or hot asphalt, noise, and blocked access.

  • Phase the work so only the area that can be dried in by day's end is opened.
  • Schedule loud and smelly work for nights, weekends or closed hours. Shut down or filter air intakes near the work.
  • Protect interiors under the work zone with poly sheeting, and move inventory or equipment where needed.
  • Control the ground. Mark crane and dumpster zones, protect entrances with covered walkways, and keep fire lanes open.
  • Tell tenants in writing with dates, hours, contacts and what to do if water appears. Check the lease for notice and access terms.
  • Agree on weather rules. The contract should say how the crew will monitor the forecast and secure the roof before storms, which matters during Florida's June-to-November hurricane season.

See what to expect during roof replacement.

How to choose a provider

  • Map every roof section with its area, system, install date, contractor and warranty.
  • Schedule inspections at least twice a year and after major storms, and keep photo reports.
  • In hail country, ask for an FM 4470 Class 1-SH or UL 2218 Class 4 assembly and a cover board.
  • Get a moisture survey before deciding between repair, coating, recover and tear-off.
  • Confirm the code edition and recover limits with your building department.
  • Ask your insurer which wind uplift rating and roof terms apply to your policy.
  • Decide whether an independent consultant should write the specification.
  • Bid the same written specification to several qualified contractors.
  • Compare warranty type (NDL, prorated, material-only), term, exclusions and inspection duties.
  • Plan tenant notices, phasing, air intake protection and storm procedures.
  • Record the Notice of Commencement (Florida) or follow retainage rules (Texas) and collect lien releases.
  • Set a yearly reserve and review it after each inspection.

Related roofing guides

Roofing by state and city

Questions people ask

What is the best commercial roofing system?

There is no single best system. TPO and PVC suit many warehouses and retail buildings that want a reflective surface, modified bitumen suits roofs with foot traffic, spray foam suits irregular roofs, and metal suits metal buildings. The right choice depends on the deck, drainage, wind zone, insurer requirements, rooftop equipment and how long you will own the building.

How many times can a commercial roof be recovered?

Generally once. The Florida Building Code requires tear-off when a roof already has two or more coverings, when it is wet or deteriorated, and in several other cases. Texas cities use the International Building Code, which has a similar recovering-versus-replacement section. Confirm the edition and any local amendments with your building department.

Is an FM 1-90 roof rated for 90 mph winds?

No. FM ratings describe uplift pressure in pounds per square foot, not wind speed. A 1-90 assembly passed a 90 psf test for one minute. FM applies a 2-to-1 safety factor, so the rating you need depends on the calculated pressure for your building's location, height and roof zones.

Does an NDL warranty cover storm damage?

Usually not. An NDL warranty removes the dollar cap on covered repairs, but most exclude storms beyond a stated wind speed, hail unless added, ponding water and damage by others. Storm damage is generally an insurance matter. Read the exclusions and any wind or hail riders before you sign.

How much should I reserve each year for a commercial roof?

A simple method is to divide the estimated replacement cost by the remaining years of life. If a section will cost an estimated $400,000 in 8 years, that is about $50,000 a year. Update the estimate after each inspection, since storms, leaks and material prices can change both numbers.

Do I need a permit to re-roof a commercial building in Florida?

Yes. Florida's 2026 permit exemption for work under $7,500 applies only to single-family homes. Commercial reroofing needs a permit and a licensed contractor. For improvements over $2,500, the owner must record and post a Notice of Commencement before the first inspection.

Who licenses commercial roofers in Texas?

No state agency does. Texas has no state roofing license. Owners should check city registrations, certificates of insurance, safety records and references. The Roofing Contractors Association of Texas runs a voluntary credential with a commercial exam and a $500,000 general liability requirement.

Can I coat my roof instead of replacing it?

If the roof is dry, well attached and drains properly, a coating can extend its life. If the insulation is wet or the membrane is loose, coating will not fix it and may trap water. Get a moisture survey first and compare the coating warranty with a replacement warranty.

What is a moisture survey?

It is a test that finds wet insulation under a roof membrane, using infrared cameras, nuclear meters or electrical methods, confirmed by small core cuts. It is the key step before deciding between repair, coating, recover and tear-off, because wet insulation loses insulating value and can rot decks.

Do commercial roofs need a windstorm certificate on the Texas coast?

If the building is insured, or will be insured, by TWIA, work done since 1988 must meet TWIA's building code and inspection requirements. Plan the inspection into the job, because certifying finished work after the fact usually costs more and may require a licensed engineer.

How can I tell if my roofer's bid is complete?

Compare it against a written specification: the system, thickness, insulation R-value and slope, attachment in field, perimeter and corner zones, edge metal, flashing details, warranty type and term, permit, disposal and schedule. Missing items are often where change orders come from later.

What hail rating should a commercial roof in Texas have?

IBHS recommends that low-slope roofs in hail-prone areas carry FM Approvals 4470 Class 1-SH (Severe Hail) or UL 2218 Class 4. FM 4470's minimum hail level is Moderate Hail, which IBHS considers too low for hail country. A cover board under the membrane adds puncture resistance, and hail guards protect rooftop condenser coils. Ask bidders to name the tested assembly, not just the membrane, because the rating applies to the whole system. If FM Global insures the building, follow its requirements.

Are ballasted or green roofs a good idea in Florida or on the Texas coast?

IBHS advises against stone ballast, ballast pavers, pedestal pavers, loose pea-gravel built-up roofs and vegetative roofs in hurricane-prone regions, which include the Gulf and Atlantic coasts where design wind speeds for ordinary buildings exceed 115 mph. Loose stones and plants can become wind-borne debris. Inland, IBHS says these systems should meet the uplift requirements in its guide and be installed to FM and SPRI standards. Check your code and insurer before choosing one.

What should I collect from the roofer when the job is finished?

Get the manufacturer's warranty in writing, the contractor's workmanship warranty, an as-built roof plan, product data sheets and approvals, the final permit inspection approval, any windstorm certificate on the Texas coast, and lien releases from the contractor, subcontractors and suppliers before you make final payment. Store them with your roof asset plan, because insurers, buyers and future roofers will ask for them.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration