New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Fri, Nov 20, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Roofing

Cool Roofs and Energy Bills in the South: Do Reflective Roofs Pay Off?

What Florida field tests show about white and reflective roofs, how CRRC ratings and SRI work now that ENERGY STAR roofs are gone, radiant barriers, coatings, utility rebates and commercial code rules.

Yes, a reflective roof usually lowers cooling bills in Texas and Florida. Florida Solar Energy Center tests found white tile and white metal roofs cut cooling energy 18% to 26% versus dark shingles, while light shingles saved only 3% to 5%. Compare products by Cool Roof Rating Council aged ratings, since ENERGY STAR stopped certifying roofs in 2022. Radiant barriers can add 8% to 12% savings, and some utilities, such as CPS Energy, offer rebates.

Key facts

  • FSEC Fort Myers tests: white tile and white metal roofs cut cooling energy 18-26% and peak demand 28-35% versus dark shingles.
  • Light-colored shingles saved only 3-5% in the same tests; terra cotta tile 3-9%.
  • LBNL: a clean white roof reflecting 80% of sunlight runs about 55°F cooler than a gray roof reflecting 20%.
  • EPA: cool roofs can reduce peak cooling demand 11-27% in air-conditioned homes.
  • EPA sunset the ENERGY STAR roof products program on June 1, 2022.
  • PNNL: radiant barriers can cut cooling costs 8-12% in hot climates.
  • CPS Energy offers a cool roof rebate of up to $0.20 per sq ft of conditioned space.
  • Florida's commercial energy code requires reflectance options for low-slope roofs over cooled space in Climate Zones 1-3.
  • The federal Energy Efficient Home Improvement Credit covered improvements placed in service through Dec. 31, 2025 (IRS).
  • FSEC estimated white tile and white metal roofs save about 600 to 1,100 kWh a year; at EIA's August 2026 prices (14.99 cents FL, 15.91 cents TX) that is roughly $90 to $175.

What makes a roof 'cool'?

A cool roof stays cooler in the sun because of two surface properties:

  • Solar reflectance (also called albedo): the share of sunlight the surface reflects. EPA calls it the most important cool-roof property.
  • Thermal emittance: how well the surface sheds the heat it does absorb by radiating it away. EPA says it matters most in warm, sunny climates.

Lawrence Berkeley National Laboratory (LBNL) notes that about half of the sun's energy arrives as invisible near-infrared light. "Cool-colored" products use pigments that reflect that invisible light, so a dark-looking shingle or tile can still run cooler than a standard one.

How big is the difference?

  • LBNL: on a typical summer afternoon, a clean white roof that reflects 80% of sunlight stays about 55°F cooler than a gray roof reflecting 20%.
  • LBNL: a cool-colored roof reflecting 35% stays about 22°F cooler than a look-alike reflecting 10%.
  • The Pacific Northwest National Laboratory notes that roof surfaces in hot climates can top 160°F.

What is a cool roof rating (SRI), and what happened to ENERGY STAR roofs?

The Cool Roof Rating Council (CRRC) runs the main U.S. rating program. Products are listed in its Rated Products Directory with initial and three-year-aged solar reflectance and thermal emittance, and many listings show a Solar Reflectance Index (SRI). SRI combines reflectance and emittance into one number, calculated under ASTM E1980: higher is cooler. Florida's energy code refers to CRRC test methods and to SRI calculated from aged values.

Aged values matter. Dirt, algae and weathering lower reflectance over time, especially on low-slope roofs. EPA notes cool roofs may need periodic cleaning to keep their reflectance.

ENERGY STAR for roofs has ended. EPA sunset the ENERGY STAR roof products program on June 1, 2022. Since then no roofing product is ENERGY STAR certified. If a product label, ad or program still cites ENERGY STAR for a roof, ask for the CRRC rating instead. CRRC published an info sheet (updated March 2025) for programs that still referenced ENERGY STAR roofing.

Does a white or cool roof lower my electric bill?

Yes, in air-conditioned homes in hot climates, often noticeably. The best Florida evidence comes from the Florida Solar Energy Center (FSEC) and FPL, which instrumented side-by-side homes in Fort Myers with the same plan, orientation and R-19 ceiling insulation:

RoofCooling energy savings vs dark shinglesPeak demand reduction
White barrel tile, white flat tile, white metal18% to 26%28% to 35%
Terra cotta tile3% to 9%Not stated in abstract
White (light-colored) shingles3% to 5%Not stated in abstract
Dark shingles, sealed attic with R-19 roof-deck insulation6% to 11%Not stated in abstract

In the control home, attic temperature at the peak summer hour ran 40°F above outdoor air. With highly reflective roofs it was no higher than outdoor air. Earlier Florida before-and-after tests measured average AC savings of 19%.

EPA adds that in air-conditioned homes, a cool roof can cut peak cooling demand by 11% to 27%, and in homes without AC it can lower maximum indoor temperatures by 2.2°F to 5.9°F. CPS Energy in San Antonio says a properly installed cool roof can reduce cooling demand by 10% to 15%.

What changes your result: how much attic insulation you have, whether ducts run through the attic, roof color and material, shading, and how clean the surface stays. The FSEC study is from 2002; newer homes with better insulation may see smaller percentages. In the South, LBNL and EPA both say the winter "heating penalty" from a cool roof is typically small compared with summer savings.

Are reflective shingles worth it in Texas?

They help, but less than many buyers expect. In FSEC's tests, light-colored shingles saved only 3% to 5% on cooling, far less than white tile or white metal. Asphalt shingles are harder to make highly reflective than metal, tile or membranes. "Cool-colored" shingle lines with near-infrared reflective granules exist, according to LBNL, and their tested reflectance is listed in the CRRC directory.

When reflective shingles make most sense:

  • You are replacing the roof anyway, and the reflective version costs little more.
  • Your ducts or air handler sit in the attic.
  • Your utility offers a rebate (see CPS Energy below).
  • Your HOA limits you to shingles. Texas Property Code s. 202.011 bars most HOAs from prohibiting shingles designed to provide heating and cooling efficiencies greater than customary composite shingles, if they resemble approved shingles, are equal or better quality and match neighborhood aesthetics.

If cooling cost is the main goal and the HOA allows it, a light-colored metal or tile roof, or attic improvements, usually do more.

Does a radiant barrier help in Florida?

Often, yes. PNNL's Building America guidance says radiant barriers can cut cooling costs 8% to 12% in hot climates and can be cost-effective in hot-dry and hot-humid climates where the roof gets direct summer sun. They are seldom cost-effective in mild marine or cold climates.

  • During a re-roof with deck replacement: foil-faced OSB sheathing, installed foil side down.
  • Without a new deck: perforated radiant barrier sheeting attached to rafters or truss chords.
  • Do not lay a radiant barrier on top of attic floor insulation. PNNL warns that it traps moisture and creates a risk of mold and wood rot.
  • Use a perforated product, which is less likely to trap vapor, and an experienced installer.

A radiant barrier and a reflective roof both attack the same heat. Adding both gives diminishing returns. If your roof is already white or highly reflective, the radiant barrier will save less.

Do roof coatings reduce cooling costs?

White elastomeric coatings are a common way to make low-slope roofs reflective, and LBNL lists elastomeric coatings among white cool-roof products. On a sound, dry, well-drained flat roof, a reflective coating can lower roof temperature and cooling load. Two cautions:

  • A coating is not a repair for a wet or failing roof. See our flat roof guide for when coatings work.
  • Reflectance drops as the surface gets dirty. EPA notes low-slope cool roofs may need periodic cleaning. Check the coating's three-year-aged rating in the CRRC directory, not just its initial value.

On steep-slope shingle roofs, Florida's code requires any elastomeric or maintenance coating over asphalt shingles to follow the shingle manufacturer's instructions. Ask the shingle maker before coating, because a coating may affect the warranty.

Cool roof rebates in Texas and Florida

Utility programs change often. Here is what we found on official utility pages as of this update:

UtilityCool roof incentive?Details
CPS Energy (San Antonio)Yes, residential cool roof rebateUp to $0.20 per square foot of conditioned space; one per account; at least 75% of the roof replaced with a cool roof and no significant shading; working air conditioning required; apply within 30 days of completion; spec sheet with initial solar reflectance (CRRC) required. The program page listed a February 1, 2025 to January 31, 2026 install window, while its terms list February 1, 2026 to January 31, 2027. Confirm the current window before you buy.
Austin EnergyNo cool roof rebate listed on its residential rebates page (last reviewed by the utility February 18, 2026)Lists whole-home "Home Energy Savings" rebates averaging $3,000, a lower-cost "Essential" version averaging $1,500, solar screens, weatherization assistance and other measures. Ask whether attic or roof-related measures qualify.
FPL (Florida Power and Light)No cool roof rebate listed on its programs pageOffers an instant $220 rebate for upgrading ceiling insulation, plus air conditioning rebates.

Other Texas and Florida utilities (Oncor-area retail programs, CenterPoint-area programs, Duke Energy Florida, TECO, JEA, OUC and co-ops) may run their own programs. Check your utility's rebate page, and search the CRRC codes and programs database. EPA's heat island page notes that utility and city cool roof rebates exist in 11 states nationally, based on CRRC data last updated in 2022, and cites San Antonio's program as an example.

Federal tax credits: the IRS says the Energy Efficient Home Improvement Credit covered qualifying improvements placed in service through December 31, 2025, and is no longer available for new work.

Does roof ventilation affect AC costs?

Some, but less than roof color and insulation. In an FSEC study summarized by the Air Infiltration and Ventilation Centre, two solar attic fans on a Florida home cut peak attic temperature about 22°F but air conditioning energy only about 6%, and earlier studies found powered attic fans often used more energy than they saved unless the attic was uninsulated. Passive ventilation sized to code (1/150 or balanced 1/300 of attic floor area) protects the roof and controls moisture, and keeping ducts sealed and insulated matters more for comfort. Details: decking, underlayment and ventilation.

Which cool roof materials work on Texas and Florida homes?

EPA groups cool roof products by roof slope. Most houses in Texas and Florida have steep-slope roofs (pitched roofs you can't walk on easily), while porches, additions, condos and commercial buildings often have low-slope (nearly flat) roofs.

Steep-slope roofs (most houses)

  • Asphalt shingles with light or cool-colored granules. The cheapest way to add some reflectance, but the smallest gain in Florida testing.
  • Tile. EPA calls terra cotta naturally cool. Glazed or coated white tile is among the most reflective steep-slope choices.
  • Metal shingles, tiles or panels with reflective paint or granules. Painted metal can be white or a cool color.
  • Polymer or composite shingles with light or cool pigments.
  • Directionally reflective materials that look white from above but darker from the street, which can help where looks or HOA rules matter.

Low-slope roofs (flat sections and commercial)

  • Single-ply membranes (such as white TPO or PVC) with light or cool pigments.
  • Liquid-applied coatings and fluid-applied membranes in light or cool colors.
  • Asphaltic membranes (modified bitumen cap sheets) with reflective granules.
  • Light-colored aggregate such as gravel.

How reflective were the roofs in the Florida test?

The FSEC Fort Myers study measured the solar reflectance (the share of sunlight bounced away) of each roof it tested. The pattern is clear: the whiter the surface, the bigger the saving.

Roof testedMeasured solar reflectanceCooling savings vs dark shingles (adjusted, July 2000)
Dark gray shingle (control)8.2%Baseline
White shingle24.0%10.6%
Terra cotta barrel tile34.6%7.7%
White painted metal (5-vee)66.2%24.0%
White barrel tile74.2%18.5%
Flat white tile77.3%21.5%

The monthly numbers above are from one July. Over a full year, the authors estimated 3% to 5% savings for the white shingle and 18% to 26% for the three white roofs. Notice that a "white" shingle reflected only 24% of sunlight, less than a third of what white tile reflected. That is why shingle color alone moves the needle so little. White metal saved the most even though white tile reflected slightly more. The authors credit metal's lower nighttime and early-morning attic temperatures, which cut evening cooling demand.

LBNL notes that cool-colored pigments can raise a product's solar reflectance by as much as 0.4 (40 percentage points) without changing how it looks, so a tan or gray "cool" tile or metal can land between the dark control and the white roofs in this table. Check the product's actual rating rather than guessing from color.

How much money does a cool roof save per year? A worked example

Percentages are easier to understand once you turn them into dollars. Here is a rough, transparent calculation using published numbers. It is an illustration, not a prediction for your house.

  1. Start with the measured savings. FSEC estimated that the white tile and white metal roofs in Fort Myers would cut annual cooling use by about 600 to 1,100 kWh. Light shingles saved about 110 to 210 kWh, and terra cotta tile about 100 to 300 kWh.
  2. Multiply by your electricity price. The U.S. Energy Information Administration (EIA) reported average residential prices for August 2026 of 14.99 cents per kWh in Florida and 15.91 cents in Texas.
  3. Do the math. At about 15 cents, 600 to 1,100 kWh is roughly $90 to $165 a year. At about 16 cents, it is roughly $96 to $175. A light shingle's 110 to 210 kWh works out to only about $17 to $34 a year.

Why your number may be higher or lower

  • House size. The test homes had only 1,144 square feet of ceiling. A 2,500-square-foot single-story home has more than twice as much roof absorbing sun, so savings could scale up.
  • Insulation. The test homes had R-19 ceiling insulation, below what ENERGY STAR now recommends for Florida and Texas. A better-insulated attic lets less heat through, so the roof color matters less.
  • Ducts in the attic. The test homes had attic ducts, which is common in both states. Ducts in a 135°F attic gain heat; in a cooler attic they gain less.
  • Your thermostat and your rate plan. Bills depend on how cold you keep the house and on your utility's rate structure. In Texas's deregulated areas, your retail plan's price per kWh can differ a lot from the state average.

Payback: compare the extra cost, not the whole roof

If you are replacing the roof anyway, the cost that matters is the difference between the cool option and the standard one. Divide that difference by your estimated yearly savings (plus any rebate) to get a rough payback in years. For example, if a white metal roof costs $3,000 more than the dark metal you were already considering, and it saves about $150 a year, payback is about 20 years from energy alone. If the cool version costs only a few hundred dollars more, payback can be a few years. Ask every bidder to price both versions so you can see the real gap.

Peak demand matters too. The same FSEC study found the white roofs cut cooling power at the hottest hour (4 to 6 p.m. on the peak day) by about 34% to 40%. That is when utilities strain hardest during Texas and Florida heat waves, and it is why some utilities pay rebates for cool roofs.

How much does a cool roof cost?

Published, dated cost data for cool roofs is thin. Fixr's cool roof cost guide (updated January 31, 2025) puts national costs at $7,500 to $30,000, with a national average of about $10,000, for a 1,500-square-foot roof. Its examples:

Fixr example (1,500 sq ft roof, 2025)Total
Single-layer reflective roof on a low-pitch home (low end)About $6,000
White solar-reflective architectural shingles (typical)About $10,000
Intensive green roof on a reinforced low-pitch roof (high end)About $40,000

Fixr ranks material tiers this way: single-layer flat-roof systems and standard white asphalt shingles are the least expensive; metal, reflective architectural shingles and some tile cost more; tile with solar-reflective glazes is near the top. EPA adds that products with infrared-reflective pigments generally cost more than conventional products.

For Texas and Florida, a full re-roof usually costs more than these national examples because roofs are larger and code requirements are stricter. See our roof replacement cost guide for 2025 city benchmarks in Houston, Dallas, San Antonio, Miami, Tampa, Orlando and Jacksonville.

Rebates reduce the gap, not the whole cost

A rebate like CPS Energy's (up to $0.20 per square foot of conditioned space) is real money but small next to a roof. On a 2,000-square-foot home, the maximum would be about $400. Treat rebates as a tiebreaker when you are already re-roofing, not as a reason to replace a sound roof.

Old tax credit claims are out of date. Some cost pages still say cool asphalt roofs may qualify for a federal tax credit. The IRS says the Energy Efficient Home Improvement Credit covered work placed in service through December 31, 2025, so it does not apply to a roof installed now.

Does it matter where in Texas or Florida you live?

Yes. Building codes divide the country into climate zones (CZ) by county, from 1 (hottest) upward. The lower the number, the more a cool roof helps and the smaller any winter penalty.

AreaClimate zone (per sources below)What it means for a cool roof
Miami-Dade, Broward and Monroe counties1A (very hot, humid), per the Florida energy code commentary from FRSAStrongest case for a reflective roof; almost no heating penalty
Rest of Florida (Tampa, Orlando, Jacksonville)Hot-humid; Florida's commercial code applies cool roof rules in Zones 1 to 3Strong case, especially for homes with attic ducts
Dallas-Fort WorthMoved from CZ3 to CZ2 in the 2021 IECC map, per Johns Manville's summary of the changeHotter classification than before; cooling dominates
Houston, San Antonio, Austin, Gulf CoastHot-humid lower zonesCooling dominates; cool roof plus attic work pays best
Texas Panhandle (Amarillo area)Colder, higher zoneReal winters; weigh the heating penalty and hail first

Johns Manville notes that about 10% of U.S. counties changed zones in the 2021 map, nearly always to a warmer zone, and that the change can raise attic insulation requirements (for example from R-38 to R-49 in the DFW example). To confirm your county's zone, ask your building department or use the U.S. Department of Energy's county climate zone guide.

The winter "heating penalty" in Texas

A reflective roof also reflects winter sun, so it can slightly raise heating use. EPA says the penalty is typically offset by summer savings, partly because winter sun is lower and days are shorter. LBNL's map shows the summer benefit outweighing the winter cost across most of the U.S. except the far north. In practice, this matters little in Florida or South Texas. In the Panhandle, where heating is a bigger part of the bill, a medium cool color can be a sensible middle ground.

Should you fix the attic before changing the roof color?

Often, yes. A roof's color controls how much heat reaches the attic. The attic floor insulation and the ducts decide how much of that heat reaches you. Fix the cheaper side first if it is lacking.

How much attic insulation do you need?

ENERGY STAR's recommended levels for existing wood-framed homes, based on the 2021 IECC:

Climate zoneAttic with no insulation: addAttic with 3 to 4 inches: add
1 (South Florida)R30R25
2 (most of Florida, much of Texas)R49R38
3R49R38
4A and 4BR60R49

If your attic has only a few inches of old insulation, adding more may beat a roof color change for the money. FPL's instant $220 ceiling insulation rebate is aimed at exactly this. Insulation also keeps working at night and in winter, unlike roof reflectance.

What the Florida test says about sealed attics

FSEC's "sealed attic" house had R-19 spray foam under a dark shingle roof deck instead of ceiling insulation. Its attic stayed much cooler, but cooling savings were 6% to 11% and peak savings on the hottest day were close to zero. The researchers called the cooler attic "deceptive" because the ceiling below had no insulation. They also found the roof deck in that house ran almost 20°F hotter than the control's. The lesson: a cooler attic thermometer is not the same as a lower bill. Ask what the whole system will do.

Ducts and air handlers

In many Texas and Florida homes the air handler and ducts sit in the attic. On a peak afternoon, FSEC measured the control attic at up to 135.6°F; under the flat white tile, the maximum was 93.3°F. Cold ducts running through a 135°F attic lose a lot of cooling. Sealing and insulating ducts helps regardless of roof color, and a cool roof helps the ducts most.

Do cool roofs hold up to hurricanes and hail?

Reflectance is a surface property. It does not tell you anything about wind or hail resistance. A white shingle, tile or metal roof is only as strong as its product rating and installation. Check each of these separately:

  • Wind: the product's wind classification and, in Florida, its Florida Product Approval or Miami-Dade Notice of Acceptance in the High-Velocity Hurricane Zone. See Florida code and HVHZ rules.
  • Hail: a UL 2218 Class 4 impact rating if you live in North Texas, Central Texas or the Panhandle. See the best roofing material for Texas.
  • Fire: a Class A fire rating where wildfire is a concern.
  • Coastal corrosion: metal finishes and fasteners suited to salt air near the Gulf or Atlantic.

Two practical cautions. First, a coating does not add wind or impact resistance to the roof under it. Second, insurance discounts follow the wind and hail features, not the color. In Florida, wind mitigation credits look at roof covering, deck attachment, roof-to-wall connections and secondary water resistance. In Texas, impact-resistant discounts depend on a labeled UL 2218 product. A cool roof that also meets these standards gets both benefits. See wind mitigation inspections.

How do you keep a cool roof cool? Dirt, algae and cleaning

Humid Texas and Florida weather is hard on bright surfaces. Dust, pollen, soot and algae darken a roof, and a darker roof absorbs more sun. That is why the Cool Roof Rating Council lists three-year-aged values, and why Florida's commercial code bases compliance on aged reflectance and assigns default values to products without aged test data.

  • Compare aged, not initial, numbers. A product with a slightly lower initial reflectance can end up cooler after three years if it resists soiling better.
  • Low-slope roofs collect more dirt. EPA notes they may need periodic cleaning to keep reflectance high. Water that ponds on flat roofs also leaves dirt rings.
  • Follow the maker's cleaning instructions. Membrane and coating manufacturers specify cleaners and pressure limits. Harsh cleaning can damage the surface or void the warranty.
  • Do not pressure wash asphalt shingles. High pressure can strip granules, which protect the asphalt from sun. Ask the shingle maker what it recommends for algae streaks.
  • Look for algae-resistant products. Many shingles carry algae-resistant granules, which helps keep light colors light in Florida's humidity.
  • Re-coat on schedule. Elastomeric coatings wear thin over time. Ask the coating maker how often it should be reapplied and what the warranty requires.

Keep the product's spec sheet with its CRRC rated product ID. You will need it for rebates, and it helps a future buyer or inspector understand what is on the roof.

When does a cool roof not make sense?

A reflective roof is not the right answer for every home. Think twice in these situations:

  • The roof is mostly shaded. Large trees already keep sun off the roof. CPS Energy's rebate, for one, excludes roofs with significant shading.
  • The roof is sound and has years left. Tearing off a good roof just to change color rarely pays back on energy alone. Wait until replacement time, and fix insulation and ducts now.
  • You already have light tile. White or light concrete tile is already reflective. Upgrading will not repeat the gains in the FSEC study, which compared against dark shingles.
  • Neighbors look down on your roof. LBNL warns that glare from a bright white or silvery roof on a low building can bother people in taller buildings nearby. A cool color that is not bright white avoids this. This comes up with condos, townhomes and commercial buildings next to taller ones.
  • A coating is being sold as a repair. Coating a wet, blistered or failing flat roof traps the problem. Fix or replace first.
  • Your home is not air-conditioned. You will not save on bills, though EPA notes cool roofs can lower maximum indoor temperatures by 2.2°F to 5.9°F, which still matters for comfort and heat safety.
  • Your HOA bans the color you want. In Texas, the HOA law protects certain energy-efficient shingles, not every reflective product. In Florida, check your declaration and get written approval before you order.

Cool roofs, solar panels and HOA rules

Solar panels and cool roofs work on the same problem from different angles. Panels shade the part of the roof they cover, so the roof under them gets less sun no matter its color. That is why Florida's commercial energy code exempts roof areas covered by photovoltaic panels and solar water heaters from its reflectance rules.

If you plan solar within a few years, choose the roof first, since panels should go on a roof with plenty of life left. A cool roof under and around panels still helps on the unshaded sections. See roofs and solar panels for re-roofing with panels in place.

Florida HOAs

Florida Statute 163.04 bars deed restrictions, covenants and HOA declarations from prohibiting solar collectors, clotheslines or other energy devices based on renewable resources, though an association may decide where on the roof panels go within an orientation facing south or within 45 degrees east or west of south, if that does not impair the system. The statute addresses energy devices, not roof color or roofing materials. A reflective roof color is generally an architectural review issue under your HOA's own rules. Get written approval before ordering.

Texas HOAs

Texas Property Code s. 202.011 protects certain shingles that provide better heating and cooling efficiency than customary composite shingles, as covered above. For solar, Texas Property Code ch. 202 also has separate rules on solar energy devices. Read your HOA's architectural guidelines and submit your product spec sheet with the request.

Why cities care: cool roofs and urban heat

Cool roofs also help neighborhoods, not just one house. EPA explains that when many roofs reflect sunlight, cities heat up less. That reduces energy use and the air pollution that comes with it, and it limits ground-level ozone, which forms faster in heat. EPA cites a UK study that found citywide cool roofs could offset 18% of heat-related deaths linked to the heat island effect.

Based on CRRC data last updated in 2022, EPA counts cool roof requirements in at least 13 cities and counties, seven states and the District of Columbia; eight voluntary programs such as LEED v4.1 heat island credits; and 35 utility and city rebate programs in 11 states. It also notes whole-building incentive programs in Texas, mostly for new construction or full retrofits. In our two states, the clearest examples are Miami Beach's Urban Heat Island Ordinance (No. 2019-4252) and CPS Energy's rebate in San Antonio.

For commercial owners in Houston, Dallas, Miami or Tampa, a reflective low-slope roof can also help with green building certifications that tenants ask about. Ask your design professional which credits your project can earn.

How to read a cool roof rating before you buy

  1. Get the CRRC product ID from the bidder or the product's spec sheet.
  2. Look it up in the Cool Roof Rating Council's Rated Products Directory at coolroofs.org.
  3. Read the initial and three-year-aged solar reflectance (0 to 1; higher reflects more) and thermal emittance (0 to 1; higher sheds heat better).
  4. Check the SRI if listed. Higher is cooler. Compare aged SRI to aged SRI.
  5. Confirm the color. Ratings are color-specific. A product line's "white" and "charcoal" have very different numbers.
  6. Match the rating to the program. CPS Energy asks for a spec sheet showing initial solar reflectance from CRRC. Florida's commercial code uses aged values. Find out which your rebate or permit requires.
  7. Ignore ENERGY STAR roof claims. The program ended in 2022. Ask for the CRRC listing instead.
  8. Keep copies of the listing, spec sheet and invoice with your roof records.

Questions to ask a roofer about a cool roof

Bring these to every bid meeting. A contractor who can answer them clearly has done this before.

  • What is the CRRC product ID, and what are the initial and three-year-aged reflectance and emittance for the exact color you are quoting?
  • What does the same roof cost in the standard color or finish? Please price both on the same estimate.
  • Does this product carry the wind rating, UL 2218 impact class and Class A fire rating my area needs? In Florida, what is the Florida Product Approval or Miami-Dade NOA number?
  • Will you check my attic insulation, ventilation and ducts while you are up there, and note any problems in writing?
  • If my deck is being replaced, what would a radiant barrier sheathing upgrade cost?
  • For a coating: is my roof dry and sound enough, does the roof or shingle maker allow it, and how often will it need recoating?
  • Will you provide the spec sheet and paperwork my utility's rebate requires, and by when?
  • What cleaning does the manufacturer allow without voiding the warranty?

Get the answers in the written proposal. See the roofing contract checklist and how to choose a roofing contractor.

Commercial energy code requirements for cool roofs

Florida

Florida's commercial energy code (Section C402.3) requires low-slope roofs directly above cooled conditioned space in Climate Zones 1, 2 and 3 to meet one or more options in Table C402.3, based on three-year-aged solar reflectance and thermal emittance or aged SRI. Miami-Dade, Broward and Monroe counties are Climate Zone 1A. Exempt areas include portions covered by solar panels, roof gardens, above-roof decks, skylights and equipment; areas shaded by permanent features at summer solstice; ballasted areas with at least 17 psf stone or 23 psf pavers; and roofs where at least 75% of the area meets an exception. Products without aged ratings are assigned default values. Miami Beach also has its own Urban Heat Island Ordinance (No. 2019-4252), cited by EPA.

Texas

The State Energy Conservation Office has adopted the 2015 International Energy Conservation Code for commercial buildings, per the Legislature's 2025 analysis of SB 783, and began work toward newer editions. Cities such as Austin, Houston, Dallas and San Antonio may adopt newer codes or local amendments. Ask your design professional which edition and roof reflectance rules apply to your permit.

Building owners: see the commercial roofing guide.

How to choose a provider

  • Look up the product's three-year-aged reflectance and SRI in the CRRC directory.
  • Check your utility's rebate page before buying, and note application deadlines.
  • Get HOA approval for roof color; cite Texas Property Code s. 202.011 if relevant.
  • Check attic insulation and duct sealing at the same time.
  • Consider a radiant barrier if the roof is dark and you are replacing decking.
  • Do not lay radiant barrier foil on top of attic floor insulation.
  • For coatings, confirm the roof is dry and sound and the shingle or membrane maker allows the coating.
  • Keep spec sheets and invoices for rebate and resale records.
  • Ask every bidder to price the cool and standard versions of the same roof.
  • Confirm the cool product also carries the wind, impact and fire ratings your area needs.

Related roofing guides

Roofing by state and city

Questions people ask

Does a white or cool roof lower my electric bill?

In air-conditioned homes in hot climates, usually yes. FSEC tests in Fort Myers found white tile and white metal roofs cut cooling energy 18% to 26% compared with dark shingles. EPA says cool roofs can cut peak cooling demand 11% to 27% in air-conditioned homes. Savings depend on insulation, ducts in the attic, shading and how clean the roof stays.

What is a cool roof rating (SRI)?

The Solar Reflectance Index combines a surface's solar reflectance and thermal emittance into one number using ASTM E1980; higher means cooler. The Cool Roof Rating Council lists products with initial and three-year-aged values. Use the aged values when comparing, because dirt and weathering lower reflectance over time. ENERGY STAR no longer certifies roofs.

Are reflective shingles worth it in Texas?

They help modestly. In Florida tests, light-colored shingles cut cooling energy only 3% to 5%, far less than white tile or metal. They make most sense when you are replacing the roof anyway, ducts are in the attic, a rebate applies, or your HOA requires shingles. Texas law limits HOAs from banning energy-efficient shingles that match neighborhood looks.

Does a radiant barrier help in Florida?

Usually. PNNL's Building America guidance says radiant barriers can cut cooling costs 8% to 12% in hot climates when the roof gets direct sun. Use a perforated product attached to rafters, or foil-faced decking installed foil side down during a re-roof. Never lay it on top of attic floor insulation, which can trap moisture.

Are there rebates for cool roofs in Texas or Florida?

Some. CPS Energy in San Antonio offers up to $0.20 per square foot of conditioned space for qualifying cool roofs, with conditions and set program dates. Austin Energy's and FPL's rebate pages did not list a cool roof rebate when we checked, though FPL offers a ceiling insulation rebate. Check your own utility, since programs change often.

Do roof coatings reduce cooling costs?

Reflective coatings can lower roof temperatures on sound, dry, well-drained low-slope roofs. They do not fix a failing roof, and their reflectance drops as they get dirty, so compare three-year-aged CRRC ratings. On shingle roofs, Florida's code requires coatings to follow the shingle maker's instructions, so check warranty effects first.

How much money will a cool roof save me each year?

It depends on the house, but published numbers give a rough range. FSEC's Fort Myers test estimated white tile and white metal roofs would save about 600 to 1,100 kWh a year on a small home with attic ducts. At EIA's August 2026 average residential prices of about 15 cents per kWh in Florida and 16 cents in Texas, that is roughly $90 to $175 a year. Larger homes may save more; well-insulated homes may save less.

How much does a cool roof cost?

Fixr's 2025 cost guide puts cool roofs at $7,500 to $30,000 nationally for a 1,500-square-foot roof, with a typical cost around $10,000 for white reflective architectural shingles. Products with infrared-reflective pigments usually cost somewhat more than standard versions, EPA says. Texas and Florida re-roofs often cost more because of roof size and code. Ask bidders to price the cool and standard versions side by side.

Is a white roof worth it in the Texas Panhandle?

Less clearly than on the Gulf Coast. The Panhandle has real winters, so a reflective roof's small winter heating penalty matters more, and hail is often the bigger risk. EPA and LBNL say summer savings outweigh the penalty across most of the U.S. A medium cool color with a UL 2218 Class 4 rating is a reasonable middle ground there.

Should I add attic insulation or get a cool roof?

If your attic has only a few inches of insulation, start there. ENERGY STAR recommends adding up to R30 in Zone 1 and R49 in Zones 2 and 3 for an uninsulated attic. Insulation keeps working year-round and is usually far cheaper than a new roof. When it is time to replace the roof anyway, choosing a cool version adds to the savings.

Do cool roofs get dirty and stop working?

They lose some reflectance as dust, soot and algae build up, especially on low-slope roofs. That is why the Cool Roof Rating Council publishes three-year-aged values and Florida's commercial code relies on them. Compare aged ratings, follow the maker's cleaning instructions, and never pressure wash asphalt shingles.

Is a cool roof as strong in a hurricane?

Color has nothing to do with wind or hail resistance. A cool roof is as strong as its product approval, wind rating, impact rating and installation. In Florida, check the Florida Product Approval or Miami-Dade NOA; in hail country, look for UL 2218 Class 4. Insurance discounts follow those features, not the color.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration