Local Guide · Roofing
Common Roof Problems: Causes, Fixes and Urgency, From Nail Pops to Flashing Failures
A field guide to the roof problems Texas and Florida homeowners actually see, what causes each one, how it is usually fixed, how urgent it is, and when the problem belongs to your warranty instead of your wallet.
Most roof leaks start at the details, not the open field of shingles: flashing at walls and chimneys, cracked rubber pipe boots, valleys, skylights and exposed nails. Curling, blistering and heavy granule loss signal aging or heat and ventilation problems. Sagging means deck or framing trouble and needs prompt attention. On a new roof, exposed nails, missing drip edge and leaks are workmanship issues to report to the installer in writing before anyone else touches the roof.
Key facts
- The 2021 IRC requires flashing at wall and roof intersections and wherever the roof changes slope or direction (R903.2.1).
- The 2021 IRC requires drip edge at eaves and rake edges of shingle roofs, overlapped at least 2 inches, extending at least 1/4 inch below the sheathing, and fastened no more than 12 inches apart (R905.2.8.5).
- When reroofing, rusted, damaged or deteriorated flashings, edgings, outlets and vents must be replaced (IRC R908.5).
- Florida's 2026 code edition requires flashing at roof edges, penetrations and changes of roof covering type, as well as wall/roof intersections, gutters and slope changes.
- Florida's 2026 code bars recovering over blistered roofing unless blisters are cut or scraped open and secured first.
- Standard rubber pipe-boot gaskets can be compromised by prolonged sun and weather exposure (Fine Homebuilding).
- Fixr (2025): skylight flashing repairs run $50 to $150 when fixable, and flashing replacement $300 to $500.
- Ask the Builder (2021 figures): chimney flashing resealing $150 to $425; replacement $275 to $1,450.
How to use this guide
Each problem below has the same five parts: what it looks like, what causes it, how it is usually fixed, how urgent it is, and any Texas or Florida twist. The photo slots describe what a good photo of the problem shows, so you can compare with what you see on your roof or in your inspection report.
Urgency ratings:
| Rating | Meaning |
|---|---|
| Emergency | Active water entry, structural sag, or storm opening. Tarp or call today. |
| Soon | Will likely leak or worsen within weeks to months, especially before storm season. Schedule within 30 days. |
| Monitor | Normal aging or cosmetic. Watch it at your twice-yearly checks. |
A note on cost: reliable published prices exist for only a few roof repairs, and they vary widely by city, roof height, material and access. We give dated, named figures where we found them. For everything else, get a written, line-item quote, and see our roof repair cost guide.
Quick reference: roof problems at a glance
| What you see | Most likely cause | Urgency |
|---|---|---|
| Ceiling stain near a chimney or second-story wall | Flashing failure | Soon; Emergency if dripping |
| Small stain in a bathroom or hallway ceiling | Cracked pipe boot, or AC or plumbing (not the roof) | Soon |
| Leak only in thunderstorms or tropical storms | Wind-driven rain at flashing, vents, valleys or gutters | Soon |
| Bumps in shingles, visible nail heads | Nail pops or exposed nails | Soon |
| Edges curling, granules in gutters | Aging, heat, poor ventilation | Monitor; plan replacement |
| Black streaks down the slope | Algae | Monitor (cosmetic) |
| Dip in the roofline, spongy deck | Rotted deck or framing problem | Emergency if new or worsening |
| Very hot attic, damp or dark deck underside, rusty nail tips | Ventilation or moisture problem | Soon |
| Scratching in the attic, chewed vents or soffits | Animals | Soon |
| Peeling paint and soft wood at roof edges | Gutter overflow, missing drip edge or kickout flashing | Soon |
| Missing or creased shingles after a storm | Wind damage | Soon; Emergency if open |
| Random dark spots, dented gutters after hail | Hail damage | Soon (claim deadlines) |
Leaks around flashing, chimneys and walls
Flashing failure
Photo slot: close-up of metal flashing where a roof meets a wall or chimney, showing a gap, rust, lifted edge or dried sealant.
What it looks like: Water stains on the ceiling or wall near a chimney, a second-story wall, or where a lower roof meets a higher wall. From outside, flashing may be bent, rusted, pulled away, or held in place only by caulk.
Common causes: Flashing is the metal (sometimes membrane) that seals joints where the roof meets something else. Model code requires it at wall and roof intersections and wherever slope or direction changes (IRC R903.2.1), and sidewall base flashing must be continuous or step flashing (R905.2.8.3). Leaks happen when flashing was never installed, was reused when the roof was replaced, was installed without counterflashing, relies on caulk alone, or has corroded in salt air.
Typical fix: Reseal if the metal is sound and only sealant has failed; replace step flashing, counterflashing or kickout flashing if bent, rusted or missing. Proper repair often means removing nearby shingles or siding.
Urgency: Soon. Emergency if water is actively coming in.
Florida's 2026 code edition expands required flashing locations to include roof edges, penetrations and changes of roof covering type, in addition to wall/roof intersections, gutters and slope changes. Near the coast, ask for corrosion-resistant metal.
Chimney leak
Photo slot: chimney base showing step flashing, counterflashing set into mortar joints, and the uphill side where water collects.
What it looks like: Stains on the ceiling or chimney breast, often worse in wind-driven rain.
Common causes: Failed step or counterflashing; cracked chimney crown or mortar letting water into the masonry; no cricket (a small diverter roof) on the uphill side of a wide chimney, so water and debris pile up behind it.
Typical fix: Ask the Builder's 2021 figures put resealing at $150 to $425 and flashing replacement at $275 to $1,450; copper costs more than aluminum or steel, and moisture damage to the chimney or framing adds to the bill. Masonry repairs may need a chimney professional.
Urgency: Soon. TDI's maintenance checklist also tells homeowners to check chimneys for loose bricks that could fall on the roof.
See our penetrations guide for more.
Pipe boots, vents and other penetrations
Cracked pipe boot
Photo slot: rubber collar around a plumbing vent pipe, cracked or split where it hugs the pipe.
What it looks like: A small leak, often in a bathroom or hallway ceiling, sometimes only in heavy rain. From outside, the rubber collar around the vent pipe is cracked, split or pulled away.
Common causes: A pipe boot is the flashing that seals a plumbing vent pipe. Common versions use a rubber gasket that Fine Homebuilding notes can be compromised by prolonged sun and weather exposure. In Texas and Florida sun, the rubber often fails years before the shingles. Squirrels also chew them.
Typical fix: Replace the boot, or install a retrofit cover. Durable alternatives include metal (lead or steel) or longer-lasting plastic or silicone designs. On a new roof, ask for upgraded boots.
Urgency: Soon. A cracked boot leaks into the wall or ceiling quietly and can rot decking.
Vent and fan leaks
Photo slot: box vents, turbine vents or bath fan caps with missing fasteners, cracked housings or lifted flanges.
What it looks like: Leaks near vents, sometimes only with wind-driven rain.
Common causes: Loose or cracked vent housings, missing fasteners, failed sealant, or vents installed without proper flashing. Turbine vents can let wind-driven rain in during tropical storms.
Typical fix: Reseat or replace the vent with proper flashing. In hurricane areas, ask about vents rated for wind-driven rain. IBHS's FORTIFIED Roof standard requires attic vents resistant to wind and rain.
Urgency: Soon.
Valleys that leak
Valley leak
Photo slot: the V-shaped channel where two roof slopes meet, showing debris buildup, worn shingles or a cut line too close to the center.
What it looks like: Leaks or stains below where two slopes meet, often in heavy rain.
Common causes: Valleys carry more water than any other part of the roof. Leaks come from debris dams (leaves, pine needles), missing or short valley lining underneath, nails driven too close to the valley center, shingles cut badly in a closed valley, or a valley that is too small for the water from a large upper roof. Model code requires valley linings installed per the manufacturer's instructions before shingles go on (IRC R905.2.8.2).
Typical fix: Clear debris. A failed valley usually needs shingles removed and the valley rebuilt with proper lining, such as self-adhering membrane or metal.
Urgency: Soon. Clear debris before every storm season.
Leaks only in heavy rain or wind-driven rain
If your roof is dry in a normal shower but leaks in a thunderstorm or tropical storm, the cause is usually water being pushed sideways or backing up, not a hole in the shingles. Look at:
- Flashing at walls and chimneys, where wind drives water behind the metal.
- Pipe boots and vents.
- Valleys that overflow when they carry a lot of water.
- Clogged gutters overflowing behind the fascia and into the soffit.
- Ridge vents and turbine vents admitting wind-driven rain.
- On low-slope roofs, ponding water rising over a seam or flashing.
- Low-slope sections (a patio cover tied into the house) that have shingles installed below the minimum slope. Model code sets a 2:12 minimum slope for asphalt shingles and requires double underlayment from 2:12 up to 4:12 (IRC R905.2.2).
Watch the leak during a storm if you can do so safely from inside the attic, and note the wind direction. That one observation often solves it.
Ceiling stain, but the roof looks fine
In Texas and Florida, a ceiling stain is often not the roof at all. Before paying for a roof repair, rule out:
- Air conditioning. Attic air handlers and ducts are common in both states. A clogged condensate drain line, an overflowing drain pan, or sweating uninsulated ducts can drip onto the ceiling, especially in humid summer months when the roof is dry.
- Plumbing. Supply lines and drains in the attic or the floor above.
- Bath fan ducts that vent into the attic or have come loose, causing condensation.
- Condensation from poor ventilation on the underside of the deck.
- A distant roof leak. Water can run along a rafter several feet before it drips.
Clues: a stain that grows on dry days points to HVAC or plumbing. A stain that appears only after rain points to the roof. A licensed inspector, plumber or HVAC technician can check the non-roof sources first.
Nail pops and exposed nails
Nail pops
Photo slot: a shingle with a raised bump or a nail head pushing up through the shingle above it.
What it looks like: Small bumps in the shingles, or nail heads visible through a shingle.
Common causes: The deck expanding and contracting with heat and humidity, nails that missed the framing or deck, nails driven at an angle or not driven flush, or overdriven nails that cut the shingle. Wet or warped decking can push nails up over time.
Typical fix: Remove the popped nail, fill the hole, renail in a correct spot, and seal or replace the shingle above it.
Urgency: Soon. Each pop is a small hole waiting for wind-driven rain.
Exposed nails on a new roof
Photo slot: nail heads visible on ridge caps, at the last course near the ridge, on flashing or in the field of shingles.
What it looks like: Shiny nail heads in visible spots, often along ridge caps, at the top course, or on flashing.
Common causes: Some exposed fasteners are unavoidable in a few spots (for example, where the last ridge cap is nailed), but they should be sealed. Exposed nails in the main field of shingles are an installation error: the nails should be covered by the course above.
Typical fix: The installer should seal or correct them. In the field of the roof, the shingles may need to be replaced.
Urgency: Soon. Report in writing to the installer under your workmanship warranty.
Curling, cupping, cracking and granule loss
Curling or cupping shingles
Photo slot: shingle edges turned up (cupping) or corners turned down (clawing), most often on the sunny slope.
What it looks like: Shingle edges lifting or curling, often worst on south and west slopes.
Common causes: Age and heat drying out the asphalt; poor attic ventilation cooking shingles from below; shingles installed over a second layer; manufacturing problems in rare cases. NRCA says shingle curling or splitting is evidence of deterioration.
Typical fix: Isolated curled shingles can be replaced, but widespread curling usually means the roof is near the end of its life. Fix attic ventilation when you replace.
Urgency: Monitor if isolated; Soon if widespread, because curled shingles blow off easily in high wind.
Granule loss and bare spots
Photo slot: close-up of a shingle with dark bare asphalt showing through, and granules piled at a downspout outlet.
What it looks like: Granules in gutters and at downspout outlets; dark bald patches on shingles.
Common causes: Aging; hail impacts that knock granules loose; pressure washing; foot traffic; scuffing from tree limbs. Some loose granules soon after installation are common, but heavy loss on a new roof is not.
Typical fix: Bare spots from hail may support an insurance claim. Age-related loss means planning replacement.
Urgency: Monitor; Soon after hail. Document with photos for any claim.
Cracked or split shingles
Photo slot: straight or jagged splits across a shingle tab.
What it looks like: Cracks across shingle tabs.
Common causes: Aging, brittleness, thermal movement, or hail.
Typical fix: Replace individual shingles if the rest are pliable; widespread cracking means replacement.
Urgency: Soon.
Blisters
Roof blisters
Photo slot: small raised bubbles on asphalt shingles, or larger raised areas on a flat-roof membrane.
What it looks like: On shingles: small raised bumps that may pop and leave bare spots. On low-slope roofs: raised pockets in the membrane.
Common causes: Moisture or air trapped in the product or between layers, expanding in heat. Poor ventilation can worsen shingle blistering. On low-slope roofs, blisters often come from moisture or poor adhesion during installation.
Typical fix: Small shingle blisters may be cosmetic; if widespread on a new roof, report to the manufacturer. Florida's 2026 code edition does not allow a new roof covering over blistered roofing unless the blisters are cut or scraped open and secured first.
Urgency: Monitor on shingles; Soon on flat roofs, where a burst blister can let water in.
Sagging roof or soft spots
Sagging or soft decking
Photo slot: a roofline that dips between rafters, or a wavy look across a slope.
What it looks like: A visible dip in the roofline, a spongy feel underfoot, or a ceiling bowing below.
Common causes: Long-term leaks rotting the deck; deck panels too thin for the span; overloaded framing from multiple roof layers or heavy tile; broken or cut rafters or trusses; termite damage.
Typical fix: Replace rotted decking. Framing problems need a contractor and possibly an engineer. Dallas notes its residential roofing permit covers coverings and decking only, and structural rafter or joist repairs need an alteration permit.
Urgency: Emergency if sagging is new or getting worse; Soon otherwise.
Wind and hail damage
Wind damage
Photo slot: shingles lifted, creased across the tab, or missing; ridge caps blown off; tiles displaced.
What it looks like: Missing shingles, creased tabs (a horizontal line where the shingle bent back), lifted edges, displaced ridge caps or tiles.
Common causes: High wind breaking the adhesive seal strip and folding shingles back. Once unsealed, shingles keep lifting in every storm.
Typical fix: Replace damaged shingles and hand-seal lifted ones if they are pliable. Widespread unsealing may mean replacement.
Urgency: Soon; Emergency if there is an opening.
Hail damage
Photo slot: a circle marked around a hail hit: granules knocked away, dark spot, sometimes a soft bruise.
What it looks like: Random dark spots where granules were knocked away; bruises that feel soft; cracked tiles; dents on metal and gutters.
Common causes: Hail impact. Impact-rated shingles are tested under UL 2218, but IBHS testing found that real-world performance varies.
Typical fix: Document and file a claim promptly. Get a neutral inspection if a contractor and adjuster disagree.
Urgency: Soon. Claim deadlines apply; see our Texas hail guide.
Tile, metal and flat roof problems
Cracked or slipped tiles
Photo slot: a broken concrete or clay tile, or a tile that has slid down and exposed the underlayment.
What it looks like: Broken pieces, gaps in rows, visible underlayment.
Common causes: Foot traffic, impact from limbs or debris, failed fasteners or adhesive, storm uplift. The underlayment below often wears out before the tile does.
Typical fix: Replace broken tiles with matching ones and reset slipped tiles. Repeated leaks on an older tile roof often mean the underlayment needs replacement.
Urgency: Soon.
Metal roof fastener and seam issues
Photo slot: screws backed out with cracked rubber washers, or rust streaks at seams.
What it looks like: Screws backing out, cracked washers, rust spots, loose panel seams.
Common causes: Thermal expansion working screws loose; washers degraded by sun; salt corrosion; dissimilar metals reacting.
Typical fix: Replace screws with larger-diameter screws and new washers; treat or replace rusted panels.
Urgency: Soon.
Ponding on a flat roof
Photo slot: standing water on a low-slope roof two days after rain.
What it looks like: Water standing in low spots after rain.
Common causes: Sagging deck, blocked drains or scuppers, or insufficient slope.
Typical fix: Clear drains; add tapered insulation or crickets; repair the deck. Model code requires secondary overflow drains or scuppers where parapets could trap water if primary drains clog (IRC R903.4.1).
Urgency: Soon. See our flat roof guide.
Black streaks, algae and moss
Photo slot: long dark streaks running down a light shingle roof, usually starting below the ridge and worst on shaded or north-facing slopes.
What it looks like: Dark brown or black streaks or a general darkening of a light roof. Green, fuzzy patches are moss or lichen, which are less common on sunny Texas roofs but appear under trees in humid parts of Florida and East Texas.
Common causes: The Asphalt Roofing Manufacturers Association (ARMA) says the streaks are algae, mainly a species called Gloeocapsa magma, carried through the air. ARMA lists coastal areas and the Gulf states among the places it is most widespread, and says it grows in all regions to some degree, especially warm, humid ones. Shade and moisture help it thrive. It is often mistaken for mildew, dirt or soot.
Is it damaging? ARMA calls algae discoloration an aesthetic problem, not a structural one. The bigger risk is how people try to remove it. It also darkens light and cool roofs, which can raise attic heat (see our cool roof guide). Moss is different: it holds moisture against the roof and can lift shingle edges, so remove it gently.
Typical fix:
- ARMA's published guidance describes gentle cleaning with a diluted chlorine bleach and trisodium phosphate (TSP) solution, applied without scrubbing and rinsed gently with water. Mixes vary by manufacturer, so follow your shingle maker's instructions first.
- ARMA says high-pressure washing should not be used for algae removal, and that scrubbing can loosen granules and shorten the shingle's life.
- Protect plants below, and remember a wet, treated roof is slippery. Many owners hire this out. See DIY roof safety.
- Cleaning is temporary; ARMA notes discoloration will likely return.
- For the next roof, ask for algae-resistant shingles. ARMA says most manufacturers offer shingles with copper-containing granules designed to inhibit algae growth.
Urgency: Monitor. Never let anyone pressure wash your shingles.
Attic heat, poor ventilation and condensation
Photo slot: the underside of roof decking in the attic, showing dark staining, frost-like or water droplets, rusty nail tips, or mold spots.
What it looks like: An attic that feels extremely hot on summer afternoons; shingles that curl or blister early, especially on the sunny slopes; damp, stained or moldy decking; rusty nail points poking through the deck; musty smells; and, in Florida humidity, sweating ducts and drywall stains near attic air handlers.
Common causes:
- Not enough ventilation. Model code (2021 IRC R806.2) generally requires net free ventilating area of at least 1/150 of the vented attic floor area, or 1/300 when conditions on vent placement and balance are met.
- Blocked intake. Insulation pushed against the soffits, painted-over soffit vents, or solid soffits installed over the vents.
- Mixed exhaust types. Ridge vents combined with box vents or powered fans can short-circuit airflow. Follow the shingle maker's ventilation requirements.
- Moisture from inside. Bath and kitchen fans that dump into the attic, leaky ducts and air leaks from the house all add humid air.
Typical fix: Clear and add intake vents, use one balanced exhaust system, add baffles so insulation doesn't block the soffits, duct fans outside, and seal air leaks and ducts. On the coast, choose vents rated for wind-driven rain; IBHS's FORTIFIED standard requires wind- and rain-resistant attic vents. Some homes use sealed (unvented) attics with spray foam on the deck, which is a design change that needs a qualified contractor and code review, not a patch.
Urgency: Soon. Ventilation is easiest to fix at re-roof time, so raise it in every bid. Details: deck, underlayment and ventilation.
Animals in the roof: squirrels, rats, raccoons and birds
Photo slot: a chewed hole at a soffit corner or roof-to-wall joint, a torn ridge or gable vent screen, or a chewed pipe boot.
What it looks like: Scratching or running sounds in the attic at dusk or dawn; droppings and torn insulation; chewed vents, soffits, fascia boards or rubber pipe boots; nests in gutters or vents; leaks where an animal opened a gap.
Common causes: Animals reach the roof by overhanging branches, wires and fences, and get in through gaps where a lower roof meets a wall, loose or rotted soffit and fascia, vent screens, and gable vents. Chewed rubber pipe boots are a common source of small leaks in both states.
Typical fix:
- Make sure every animal is out first. Sealing an animal inside causes more damage. Florida and Texas both regulate trapping some wildlife, so use a licensed wildlife or pest professional when in doubt.
- Repair the entry with durable material such as metal flashing or hardware cloth. Foam and caulk alone do not stop chewing.
- Replace chewed pipe boots, preferably with metal or chew-resistant designs.
- Trim branches back from the roofline.
- Check insulation and wiring in the attic for damage.
Urgency: Soon. Animal damage often opens the next leak, and chewed wiring is a fire risk.
Gutter, fascia and soffit problems
Photo slot: a gutter pulling away from the fascia, peeling paint and soft wood behind it, or water stains on siding below where a lower roof meets a wall.
What it looks like: Water spilling over gutters in rain; gutters sagging or pulling loose; rotted fascia boards; stained or sagging soffits; streaks or rot on the wall below the end of a lower roof.
Common causes:
- Clogged gutters and downspouts sending water behind the gutter, into the fascia and soffit.
- Missing drip edge, which model code requires on shingle roofs at eaves and rakes (IRC R905.2.8.5), letting water wick onto the fascia.
- Missing kickout flashing where a roof edge dies into a wall, so roof water runs down behind the siding.
- Gutters undersized for heavy Gulf Coast and Florida downpours, or downspouts that dump against the foundation.
Typical fix: Clean gutters and test downspouts with a hose; add drip edge and kickout flashing; replace rotted fascia and soffit before re-hanging gutters. Florida's contractor scope for roofing includes repair or replacement of fascia during roof work, so a roofer can often handle rot found during a re-roof.
Urgency: Soon. Hidden rot spreads into rafter tails and walls. Before hurricane season, make sure gutters are secure, since loose gutters can pull fascia and roof edges with them. See gutters, soffit, fascia and roof edges.
Tree damage and debris
Photo slot: a branch resting on a roof, scuffed bare granules where limbs rub, or a pile of leaves in a valley.
What it looks like: Scraped or bald patches where branches rub in wind; punctures or cracked tiles from falling limbs; leaf and pine-needle piles in valleys and behind chimneys; black streaks and moss under shade.
Why it matters: Debris dams water in valleys, the most common leak spot after flashing. Constant rubbing wears off the granules that protect asphalt from the sun. A large limb in a storm can break framing.
Typical fix: Trim limbs away from the roof (hire a tree service for anything near power lines), clear debris before every storm season, and inspect for punctures. If a tree falls on your roof in a storm, cover openings, photograph everything and call your insurer; see what to do tonight.
Urgency: Soon for debris and rubbing; Emergency for a limb through the roof.
New roof: what is normal and what is a defect?
| Usually normal | Usually a defect to report |
|---|---|
| A few loose granules in gutters right after install | Heavy granule loss or bare spots |
| Shingles that look slightly wavy until the sun seals them | Shingles that never lie flat, or that lift in the first wind |
| A sealed exposed nail at the last ridge cap | Exposed nails in the field of the roof, or unsealed nails |
| Some color variation between bundles | Obvious patchwork or mismatched sections |
| New flashing at walls and chimneys | Old rusty flashing reused (code requires replacing rusted or damaged flashing when reroofing, IRC R908.5) |
| Drip edge at eaves and rakes | Missing drip edge; code requires it on shingle roofs (IRC R905.2.8.5) |
| Any leak | |
| Nails, debris or dented gutters left behind |
Also check that the permit was closed out with a final inspection. In Houston, the permit and worksheet must be on site for inspection. In Florida, ask for the final inspection record from the building department.
When to call the warranty, and how
Most roofs come with two warranties:
- Workmanship warranty from the contractor, covering installation errors. Terms vary widely.
- Manufacturer warranty covering material defects, and sometimes installation if the roof was installed by a credentialed contractor and registered.
Call the installer first for anything on the "defect" list above, especially in the first few years. Steps:
- Take dated photos.
- Notify the contractor in writing (email or certified letter), describing the problem and asking for a repair date.
- Do not let another roofer repair it first, since that can void the workmanship warranty. Make temporary protection only (a tarp).
- If the contractor does not respond, contact the manufacturer with your registration information.
- Keep records of every contact.
If the contractor will not honor the warranty, see what to do about bad roofing work. In Florida, you can file a complaint with DBPR (850-487-1395); certain losses from licensed contractors may be eligible for the Homeowners' Construction Recovery Fund. In Texas, the Attorney General's consumer complaint process covers deceptive practices. For warranty basics, see roof warranties explained.
How to track down a roof leak, step by step
Most leak hunts fail because people start on the roof instead of inside. Work from the stain upward.
- Rule out non-roof sources. Check the AC drain pan and condensate line, attic ducts and plumbing, as described above. A stain that grows on dry days is almost never the roof.
- Note the conditions. Did it leak in every rain, only in heavy rain, or only with wind from one direction? Write down the date, time and wind direction.
- Measure from the stain. Measure from the stain to the nearest exterior wall or another landmark, so you can find the same spot in the attic and on the roof.
- Look in the attic with a flashlight during or soon after rain, if you can do so safely. Walk only on framing. Look uphill from the stain for wet wood, water trails along rafters, and daylight around penetrations. Water often travels several feet before it drips.
- Check the usual suspects above the wet area: pipe boots, vents, chimney and wall flashing, valleys, skylights and any satellite or solar mounts.
- Look from the ground with binoculars for missing shingles, lifted flashing or damaged boots. Do not climb a wet roof.
- Use a garden-hose test only with care. Professionals often run water on one area at a time, starting low and moving up, while someone watches in the attic. It works, but it puts a person on the roof and can spread water. Leave it to a roofer if you are not trained.
- Protect and document. Catch drips, move belongings, photograph the stain and any damage, and keep notes. If storm damage is possible, call your insurer before permanent repairs.
If you cannot find it, a roofer or home inspector can. Ask whether they use moisture meters or infrared cameras, which can show wet areas without opening the ceiling. See the roof inspection guide.
Repair or replace? How to decide
Repairs make sense when the problem is a detail (a boot, a flashing, a few shingles) on a roof with life left. Replacement makes sense when problems are everywhere at once. Weigh these factors:
| Factor | Leans toward repair | Leans toward replacement |
|---|---|---|
| Age | Well within expected life | Near or past it. NRCA-attributed tables list asphalt shingles at 15 to 30 years, metal 20 to 50-plus and tile about 50. |
| Problem spread | One area or one detail | Curling, granule loss or blisters across whole slopes |
| Deck | Solid | Soft or rotted in several places |
| Leak history | First leak | Repeated leaks in different spots |
| Insurance | No coverage issues | Insurer is moving roof coverage to actual cash value or requiring replacement to renew |
| Storm season | Repair holds until a planned replacement | Roof unlikely to survive the next hurricane or hail season |
Florida rules that affect the decision
- Roof age and insurance. Florida insurers may not refuse to issue or renew a homeowner's policy solely because the roof is less than 15 years old. For roofs 15 or older, they must allow a homeowner-paid inspection, and may not refuse solely for age if it shows at least 5 years of remaining useful life (Fla. Stat. 627.7011). Citizens has its own roof rules. See the Florida 15-year roof rule.
- The 25% rule. Under Fla. Stat. 553.844(5), if your roof was built, repaired or replaced to the 2007 Florida Building Code or later, repairing, replacing or recovering 25% or more of it requires only the repaired portion to meet the current code. Older roofs can face whole-section upgrade requirements under the code. Ask your roofer and building department how this applies before a large repair.
Texas factors
TDI notes that as roofs age, some insurers switch roof coverage to actual cash value at renewal, and a roof in poor condition may not be covered for a later loss. Insurers will not pay for a new roof just because the old one is worn out. If repeated hail has aged your roof, compare a series of repairs against a replacement with a Class 4 product; see the Texas roofing material guide.
Get at least two written, line-item opinions, and be wary of anyone who says the whole roof must go without showing you photos. See how long a roof lasts and roof repair costs.
How to prevent most roof problems
- Look twice a year and after every major storm. From the ground with binoculars, check for missing or lifted shingles, cracked tiles, damaged boots and loose flashing.
- Check the attic in spring and fall for stains, daylight, damp spots and animal signs.
- Keep gutters, valleys and the roof clear of leaves and pine needles before spring storms and before June 1 hurricane season.
- Trim trees back from the roof.
- Service the AC and clean the condensate line, so you don't mistake an AC leak for a roof leak.
- Replace rubber pipe boots proactively if they are cracking, especially on south and west slopes.
- Never pressure wash shingles or walk on tile.
- Keep records: install date, product, permits, warranties and dated photos. They help with insurance, resale and warranty claims.
The full seasonal list is in the roof maintenance checklist.
How to choose a provider
- Photograph the problem from inside and outside with dates.
- Rate urgency: active water or sag means act today.
- Rule out AC drain lines, ducts and plumbing for ceiling stains.
- Check flashing, pipe boots and valleys first for leaks.
- Clear valley and gutter debris before storm season.
- On a new roof, report defects to the installer in writing before anyone else repairs them.
- Ask for line-item, written repair quotes.
- Confirm repairs that need permits are permitted.
- Keep all invoices and warranty papers in one folder.
Related roofing guides
- Roof Repair Costs: Leaks, Flashing, Shingles, Tiles, and Flat Roof Patches
- Skylights, Chimneys, Vents and Roof Penetrations: Leak Hotspots and What to Do About Them
- Roof Warranties Explained: Manufacturer vs Workmanship, Transferability, and What Voids Them
- Bad Roof Job or Roofer Won't Finish: Your Options in Texas and Florida
- Roof Leaking Right Now: What to Do Tonight (and What Not to Do)
- Roof Inspections in Texas and Florida: Free vs Paid, Drone vs Walk-On, and What a Good Report Includes
- Gutters, Drip Edge, Soffit and Fascia: The Roof Edge Questions Nobody Answers
- What's Under Your Shingles: Decking, Underlayment, Secondary Water Barrier and Ventilation Explained
Roofing by state and city
Questions people ask
What causes nail pops on a roof?
Nail pops happen when nails back out and push up the shingle above. Common causes are the deck expanding and contracting with heat and humidity, nails that missed solid wood, nails driven at an angle, and wet or warped decking. The fix is to remove the nail, renail in a sound spot, and seal or replace the damaged shingle. Do not ignore them, since each pop is a potential leak.
Why are my shingles curling?
Usually age and heat. Asphalt dries out in the sun, and poor attic ventilation heats shingles from below. NRCA calls curling or splitting evidence of deterioration. Curling on just the south or west slopes is typical in Texas and Florida. Isolated curled shingles can be replaced, but widespread curling usually means the roof is near the end of its life.
What is flashing and why does it fail?
Flashing is metal or membrane that seals joints where the roof meets walls, chimneys, skylights, vents and changes in slope. Code requires it at these locations. It fails when it was never installed, was reused during a reroof, relies on caulk alone, rusts in salt air, or was bent by storms or foot traffic. Most roof leaks are flashing leaks.
What is a pipe boot and why does it crack?
A pipe boot is the flashing collar around a plumbing vent pipe. Many use a rubber gasket that breaks down in sun and weather, often well before the shingles wear out in hot climates. Squirrels also chew them. Replacement is usually a small repair. When you replace your roof, ask for upgraded boots made of metal or longer-lasting materials.
Why does my roof only leak in heavy rain?
Heavy or wind-driven rain pushes water sideways under flashing, through vents, and over valley edges, and it overflows clogged gutters behind the fascia. Low-slope sections with shingles below the minimum slope also leak in hard rain. Watch from the attic during a storm, if safe, and note the wind direction. That usually points to the source.
Are exposed nails on a new roof a problem?
Nails in the main field of shingles should be covered by the course above, so exposed field nails are an installation defect. A few exposed nails are unavoidable at the final ridge cap or some flashing, but they should be sealed. Report exposed or unsealed nails to the installer in writing under your workmanship warranty, with photos.
What causes roof valleys to leak?
Valleys carry the most water on a roof. Leaks come from debris dams, missing or short valley lining, nails too close to the valley center, poorly cut shingles in closed valleys, or too much water from a large upper roof. Keeping valleys clear helps. A failed valley usually has to be rebuilt with proper lining, which means removing shingles along it.
What causes black streaks on my roof?
The Asphalt Roofing Manufacturers Association says the streaks are algae, mainly Gloeocapsa magma, which spreads through the air and is widespread in coastal and Gulf states. It is mostly cosmetic. ARMA describes gentle cleaning with a diluted bleach solution, no scrubbing and no pressure washing. For the next roof, ask for algae-resistant shingles with copper-containing granules.
How can I tell if my attic ventilation is bad?
Signs include an attic that is extremely hot on summer afternoons, shingles curling or blistering early on sunny slopes, damp or stained decking, rusty nail tips and musty smells. Model code generally requires ventilation equal to 1/150 of the attic floor area, or 1/300 when intake and exhaust are balanced. Check that soffit vents are not blocked by insulation.
Should I repair or replace my roof?
Repair when the problem is one detail on a roof with life left. Replace when curling, granule loss or leaks are spread across the roof, the deck is soft in several places, or the roof is near the end of its expected life. Insurance matters too: Florida's 15-year roof law and Texas insurers' switch to actual cash value on older roofs can tip the decision.
How do I find where my roof is leaking?
Start inside. Rule out the AC drain line and plumbing, note when it leaks and the wind direction, then look in the attic uphill from the stain for wet wood and water trails. Water can travel several feet along framing. Check pipe boots, flashing, valleys and vents above the wet area. Hose tests and roof walking are best left to a roofer.
Can animals cause roof leaks?
Yes. Squirrels and rats chew rubber pipe boots, soffits, fascia and vent screens, and the openings let in water as well as more animals. Make sure animals are out before sealing, use metal flashing or hardware cloth rather than foam alone, replace chewed boots with chew-resistant designs, and trim branches back from the roof.
Sources
- 2021 International Residential Code, Chapter 9 Roof Assemblies (Texas edition, UpCodes)
- FRSA: Additional 2026 FBC changes
- FRSA: FBC 2026 updates, recovering versus replacement
- Fine Homebuilding, Mike Guertin: Better boot flashings last longer, seal better
- Fixr: Skylight repair cost (updated Jan. 31, 2025)
- Ask the Builder: Chimney flashing cost (2021 figures)
- Texas Department of Insurance: Insurance and your roof (updated 4/1/2026)
- Professional Roofing (NRCA), Mark S. Graham: Routine preventive maintenance for residential roofs (Oct. 2013)
- IBHS FORTIFIED Roof
- IBHS: Relative Impact Resistance of Asphalt Shingles
- Professional Roofing (NRCA): Asphalt shingle standards, wind and impact classes
- City of Dallas: Building permit guide
- Houston Permitting Center: Residential roofing permit (HPWCODE1140)
- Florida DBPR: Construction Industry (license lookup)
- Texas Department of Insurance: Tips after hail or windstorms
- Fla. Stat. s. 489.143 (2026), Homeowners' Construction Recovery Fund payments
- Texas Attorney General: File a consumer complaint
- Florida DBPR: Unlicensed activity FAQ and contact center
- ARMA: Algae discolorations of roofs (IIBEC Interface, Jan. 2003)
- Roofing Contractor: Algae on the roof, a growing problem (2004)
- 2021 IRC Chapter 8 (attic ventilation R806), Texas (UpCodes)
- Fla. Stat. s. 553.844: Windstorm loss mitigation; roofing (25% exception)
- Fla. Stat. s. 627.7011: Homeowners policies; roof age
- Fla. Stat. s. 489.105: Definitions (roofing contractor scope)
- NRCA-attributed roof life expectancy table (USDA Forest Service)
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


