New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Residential solar installers

Do Solar Panels Work Well in Texas and Florida Heat?

Heat trims a solar panel's output a little on the hottest afternoons, but Texas and Florida still rank among the sunniest places to make solar power. Here is the temperature math, month-by-month production for eight cities, and what clouds, humidity and afternoon storms really do.

Yes. Solar panels lose some output as they heat up, usually a fraction of a percent for each degree Celsius above 25°C (77°F), so a hot summer afternoon may cost roughly 10 to 20 percent of a panel's rated power. But long, bright days more than make up for it. Federal PVWatts estimates show a south-facing 1 kW array makes about 1,420 to 1,570 kWh a year in major Texas and Florida cities, with Texas peaking in July and August and Florida in spring.

Key facts

  • PVWatts estimates a 1 kW south-facing roof array makes about 1,421 kWh a year in Houston, 1,506 in Dallas, 1,483 in Austin and 1,497 in San Antonio.
  • The same model estimates about 1,552 kWh in Miami, 1,568 in Tampa, 1,544 in Orlando and 1,455 in Jacksonville.
  • PVWatts Version 5 assigns temperature coefficients of -0.47%/°C to standard modules, -0.35%/°C to premium modules and -0.20%/°C to thin film, based on over 11,000 modules.
  • A 2026 residential panel datasheet lists a Pmax temperature coefficient of -0.29%/°C and a nominal operating cell temperature of 45°C.
  • A 2026 installation manual says its panels are certified for a 98th-percentile operating temperature up to 176°F (80°C) and advises extra roof clearance and airflow in hotter regions.
  • A UC San Diego study (Solar Energy, 2011) found ceilings under rooftop PV arrays up to 2.5 K (4.5°F) cooler by day and modeled a 38 percent cut in annual cooling load for that building.
  • PVWatts' manual says its typical-year estimates can be off by up to 10 percent for annual totals and 30 percent for monthly totals, and real years can vary up to 20 and 40 percent.
  • Kiwa PVEL's 2026 scorecard runs a 2,000-hour damp heat test, double the certification test, and 32 percent of tested bills of materials had a damp heat failure.

Do solar panels lose efficiency in heat?

Yes, a little. Solar cells make slightly less power as they get hotter. Panel makers rate output at standard test conditions, which include a cell temperature of 25°C (77°F). Above that, output drops by a set percentage per degree. That percentage is called the temperature coefficient of Pmax, and it is printed on every panel datasheet.

Typical values:

  • PVWatts, the free national-lab calculator, uses -0.47%/°C for a "standard" module, -0.35%/°C for a "premium" module and -0.20%/°C for thin film in its Version 5 manual. Those values came from a statistical analysis of more than 11,000 modules. The older Version 1 used a flat -0.5%/°C.
  • Newer panels often do better. One 2026 residential panel datasheet we reviewed lists -0.29%/°C.

The minus sign means a loss. A coefficient of -0.35%/°C means the panel loses 0.35 percent of its rated power for every degree Celsius its cells run above 25°C.

Note the word cells. Cell temperature, not air temperature, is what counts. On a sunny day the cells run well above the air temperature because they absorb sunlight. How far above depends on sunlight, wind, mounting and the gap under the panel. Datasheets list a "nominal operating cell temperature" (NOCT or NMOT) as a guide; the 2026 datasheet we reviewed lists 45°C under its test conditions, which use moderate sun and air temperature. On a still July afternoon in Texas, cells can run hotter than that.

How much production do panels lose at 100 degrees?

Here is the math with a worked example. Say the air is 100°F and your rooftop cells reach 65°C (149°F). That is 40°C above the 25°C rating point.

Temperature coefficientLoss at 40°C above 25°CA 400 W panel would make about
-0.47%/°C (PVWatts standard)18.8%325 W
-0.35%/°C (PVWatts premium)14.0%344 W
-0.29%/°C (example 2026 datasheet)11.6%354 W

Formula: loss percent = coefficient x (cell temperature minus 25). Example: 0.35 x 40 = 14 percent.

These are snapshot numbers for the hottest part of the hottest days, before other losses like wiring and dust. Mornings, evenings and cooler months run closer to the rating. Over a full year, heat loss is much smaller than the peak-afternoon number. PVWatts already models cell temperature hour by hour from local weather when it gives you an annual estimate, so the city numbers on this page include heat effects.

What this means when comparing panels: a better coefficient matters more in Texas and Florida than in Minnesota. If two quotes use panels rated -0.29%/°C and -0.40%/°C, the first will hold up better on summer afternoons. The difference over a year is real but usually a few percent, not a deal breaker. See solar panel types for how cell technology affects the coefficient.

Which months produce the most solar in Texas and Florida?

Below are monthly PVWatts estimates for a 1 kW-DC fixed roof array facing due south at a 20° tilt, with the default 14 percent system losses and a standard module. Multiply by your system size: an 8 kW system makes about 8 times these numbers. The model uses 2020 typical-year weather data from the National Solar Radiation Database.

CityJanFebMarAprMayJunJulAugSepOctNovDecYear
Houston9388129127138135140134123122109861421
Dallas1019812313414215115515013611898991506
Austin1019411913513914115115413112398991483
San Antonio10395123127141141151151131125112961497
Miami1171211521451421261371361241261161101552
Tampa1221201511511521281261231261371231091568
Orlando1171091461481531291321341251341121061544
Jacksonville106101136141146126132132118117107921455

kWh AC per 1 kW-DC. Source: NLR (formerly NREL) PVWatts v8 model output, retrieved November 2026. Model estimates, not measured production.

What the pattern shows

  • Texas peaks in mid-summer. Dallas tops out at about 155 kWh per kW in July, Austin at about 154 in August, and San Antonio at about 151 in both July and August. The longest days and clearest skies win despite the heat.
  • Florida peaks in spring. Miami's best month is March, Tampa and Orlando peak in May, and Jacksonville in May. Then production dips in June and stays flatter through summer, when afternoon thunderstorms bring daily cloud.
  • Winter still works. December and January output in these cities is roughly 60 to 75 percent of peak-month output. Miami and Tampa hold up best in winter, at about 72 percent of their peak month in December, helped by a higher winter sun farther south.
  • Annual totals are close. Tampa and Miami edge out Dallas and San Antonio, with Houston and Jacksonville a bit lower. All eight are strong solar locations.

Your own roof will differ with tilt, direction, shade and equipment. Run your address in PVWatts, or compare against your installer's estimate. Our system sizing guide shows how to turn these numbers into a system size.

Are solar panels worse in summer than spring?

Per hour of sunshine, panels are more efficient in cool, bright spring weather than on a summer afternoon. That is the temperature effect. But summer days are longer, so total summer output in Texas is still highest. In Florida, spring often wins outright because summer adds thick afternoon clouds on top of the heat.

Look at the sunlight data behind the table. PVWatts reports the average solar energy reaching the tilted array each day. In Houston it climbs from about 3.8 kWh per square meter per day in January to about 6.3 in July. In Miami it is already about 6.4 in March and April, then falls to about 5.7 in June as the rainy season begins. That is the Florida spring peak in a nutshell: almost as much light as summer, with cooler cells and fewer storms.

Do solar panels work on cloudy days?

Yes, at reduced output. Sunlight reaches panels two ways: direct beams from the sun, and diffuse light scattered by clouds and the sky. Under thin or broken clouds, panels can still make a good share of their clear-day power. Under thick storm clouds, output may drop to a small fraction for that hour.

What this means in practice:

  • A cloudy morning followed by a sunny afternoon can still be a solid day.
  • Fast-moving clouds make output jump up and down in the app. That is normal.
  • A week of gray skies after a hurricane, or during a Texas winter storm, can cut production deeply. Plan batteries and backup with that in mind. See battery backup for hurricanes and outages.

Clouds also help a little with heat, since cooler cells are more efficient. And right after a cloud passes, the edge of a bright cloud can briefly push output above normal. Modern inverters handle these swings.

Does Florida's afternoon rain hurt solar production?

Somewhat, and the table shows how much. In Miami, Tampa, Orlando and Jacksonville, June through September output is lower than April and May, even though the days are longer. Tampa drops from about 152 kWh per kW in May to about 123 in August in the model. That is the cost of the daily storm cycle.

There are offsets:

  • Storms usually build in the afternoon, so mornings and midday are often clear.
  • Rain rinses the panels for free. See solar maintenance and cleaning.
  • Under Florida net metering, a sunny spring month's extra credits roll forward to help cover summer bills, within the 12-month limits of Rule 25-6.065. Our Florida net metering guide explains the true-up.

Your summer air conditioning bill rises at the same time production softens, which is why Florida owners often see their biggest bills in August and September even with solar. That is normal and is not a sign of a broken system.

How much sun does Texas get compared to Florida?

About the same overall, with a different shape through the year. Using the same PVWatts setup for each city:

CityAvg. sunlight on array (kWh/m2/day)Annual output per kW (kWh)Capacity factor
Houston5.221,42116.2%
Dallas5.451,50617.2%
Austin5.401,48316.9%
San Antonio5.471,49717.1%
Miami5.621,55217.7%
Tampa5.711,56817.9%
Orlando5.631,54417.6%
Jacksonville5.481,45516.6%

Capacity factor is the share of the year's hours the system would need to run at full rated power to make its annual output. A higher number means more output per kW installed.

West Texas is a special case. It is drier than the Gulf Coast, with more dust and, in the Panhandle and Permian Basin, frequent hail. We did not run PVWatts for West Texas cities, so check your own address. For state-level views, see is solar worth it in Texas and is solar worth it in Florida.

Do solar panels make my attic hotter or cooler?

Cooler under the panels, in the one solid study we found. Researchers at UC San Diego measured a building partly covered by solar panels in San Diego and published the results in the journal Solar Energy in 2011. They found:

  • On a clear April day, daytime ceiling temperatures under the arrays were up to 2.5 K (about 4.5°F) cooler than under exposed roof.
  • Modeling showed a significant cut in daytime heat flow through the roof under the panels.
  • At night it reversed: the ceiling under the panels stayed warmer, showing the panels act a bit like insulation.
  • Simulations found a 38 percent reduction in annual cooling load for that roof (5.9 kWh per square meter), with no change in heating load.

Two cautions. First, the study building was not a typical Texas or Florida house; the authors say the benefits are greatest for older, poorly insulated buildings such as warehouses. A home with good attic insulation and a radiant barrier will see less change. Second, panels only shade the part of the roof they cover. Expect a modest comfort benefit, not a big drop in your AC bill from shading alone.

Panels do not heat your attic. They absorb sunlight that would otherwise hit the shingles, and the air gap under them carries heat away.

Does humidity affect solar panels?

Humidity has little effect on day-to-day output. Water vapor scatters a bit of light, and humid air often brings haze and clouds, which is part of why Houston and Jacksonville score a little lower than drier, sunnier spots. The larger humidity issue is long-term durability.

Heat plus moisture over many years can weaken the materials that seal a panel. Kiwa PVEL, an independent lab, runs a 2,000-hour damp heat test, which it says is double the length of the IEC/UL certification test. It explains that in susceptible modules, moisture and heat weaken the bonds holding the module together, letting moisture in to cause corrosion or delamination. In its 2026 scorecard, 32 percent of tested bills of materials had a damp heat failure, with delamination the largest contributor.

What that means for buyers in Houston, Tampa or Miami: ask whether the exact panel model has independent reliability test results, and read the warranty's degradation terms. Our panel types guide covers testing and certifications, and solar warranties explains degradation guarantees.

Do panels degrade faster in hot climates?

Possibly, but the evidence is mixed. A review by NREL (now the National Laboratory of the Rockies) of nearly 2,000 field degradation rates found a median of 0.5 percent per year and a mean of 0.8 percent, with 78 percent of measurements under 1 percent a year. The review notes some desert systems near 1 percent a year and some hot-humid systems near zero to 1 percent, and it says the precise impact of climate had not been settled. Panel warranties for many current models guarantee lower rates; the 2026 datasheet we reviewed guarantees no more than 1 percent loss in year one and 0.45 percent a year after.

How hot do solar panels get, and is that safe?

Rooftop panels in direct summer sun run well above air temperature, and dark frames and glass can be too hot to touch. Panels are designed for it. One manufacturer's 2026 installation manual says its panels are certified under IEC 61730 for a 98th-percentile operating temperature up to 176°F (80°C), meaning the panel should spend no more than 2 percent of its operating time above that. For hotter regions, the manual recommends:

  • More distance between the panel and the roof.
  • No barriers to airflow under the panels.
  • Reflective roof surfaces to lower the temperature the module sees.

That is also why flush-mounted panels with almost no gap, or panels with debris and nests packed under them, run hotter and produce less. Keep the space under the array open.

Hot panels and cold water do not mix. The same manual says to clean only when panels are cool, such as early morning, to avoid glass breakage from thermal shock.

Do inverters and batteries lose performance in heat?

Yes, electronics can be heat-limited too. Many inverters reduce their maximum output when their internal temperature gets too high, which is called derating. Each inverter datasheet lists its operating temperature range and the temperature where derating starts. Placement matters:

  • A string inverter on a west-facing wall in full afternoon sun runs hotter than one on a shaded north wall. Ask your installer to mount it out of direct afternoon sun where the code and layout allow.
  • Microinverters sit under the panels, where it is hot, so they are designed and warrantied for that environment. Their datasheets list ambient operating ranges.
  • Batteries have operating and storage temperature limits, and some reduce charging or discharging when hot or cold. A hot Texas or Florida garage can push the upper limits. Check the battery manual before choosing a location.

For comparisons, see string inverters vs microinverters and home battery types and sizing.

What can I do to help panels beat the heat?

  • Choose a better temperature coefficient when comparing quotes. Ask for the datasheet and compare the Pmax value.
  • Keep airflow under the array. Standard racking leaves a gap; do not let debris or nests fill it.
  • Use the right roof planes. South and west faces both work in Texas and Florida. West-facing panels produce more in late afternoon, when they are hottest, but that is also when power is most valuable in some Texas plans.
  • Light-colored or reflective roofs can lower the temperature panels see, as the manufacturer manual notes.
  • Place inverters and batteries in shade with ventilation, following the manuals.
  • Do not spray water to cool panels. It wastes water, can cause thermal shock, and leaves mineral spots.

How should I judge my production in hot months?

Compare like with like. A July day in Houston should be compared to an average July day in the PVWatts estimate for your system, not to a cool, clear April day. The PVWatts manual warns that its estimates can be off by up to 10 percent for a year and 30 percent for a single month, even in typical weather, and an actual year can vary from the long-term average by up to 20 percent annually and 40 percent monthly. One cloudy month is not a broken system.

If production is low across several months compared to both the estimate and the same months last year, start with our low production troubleshooting guide.

How to choose a provider

  • Ask every installer for the panel datasheet and compare the Pmax temperature coefficient.
  • Run your address in PVWatts to see your own monthly production curve.
  • Expect Texas production to peak in July and August and Florida in spring.
  • Compare summer production to summer estimates, not to spring days.
  • Keep the space under the array free of debris and nests for airflow.
  • Ask where the inverter and battery will be mounted and how hot that spot gets.
  • Ask for independent reliability test results for the panel model if you live in a humid coastal area.
  • Read the warranty's annual degradation limit.
  • Clean panels only when they are cool, if cleaning is needed at all.

Related residential solar installers guides

Residential solar installers by state and city

Questions people ask

Do solar panels stop working when it is too hot?

No. They keep producing, just with somewhat lower efficiency. Output drops by the panel's temperature coefficient for each degree Celsius above 25°C, often about 0.3 to 0.47 percent per degree. On the hottest afternoons that may mean 10 to 20 percent below rated power. Panels are certified to operate at high temperatures, and one 2026 manual cites certification for a 98th-percentile operating temperature up to 80°C.

What is a good temperature coefficient for Texas or Florida?

Lower is better. PVWatts treats -0.35%/°C as a premium module and -0.47%/°C as standard. One 2026 residential datasheet we reviewed lists -0.29%/°C, better than the PVWatts premium value. Check your quote's datasheet for its number. Compare the Pmax coefficient, not the voltage or current coefficients, which are also printed on the datasheet.

Is a hot day or a cool day better for solar?

Per hour of sun, a cool, clear day is better because cells run cooler. That is why Florida's best months are in spring. But in Texas, long, clear summer days still produce the most total energy, so July and August lead the year in Dallas, Austin and San Antonio estimates despite the heat.

Why does my system make less in August than in May?

In Florida, summer afternoon storms block sun, and heat lowers efficiency, so PVWatts estimates for Tampa fall from about 152 kWh per kW in May to about 123 in August. In Texas, August output is usually near the yearly peak, so an August dip there may be weather or a fault. Compare to the same month last year and to your estimate before assuming a problem.

Do solar panels work in Texas winter?

Yes. Short days and a lower sun cut output, so December and January in the PVWatts estimates are roughly 60 to 66 percent of the peak month in Texas cities. Cold temperatures actually help cell efficiency. Snow and ice, rare in most of Texas, block output until they slide or melt off. A long winter storm with cloud and ice, like February 2021, can cut production for days.

Do panels cool my house?

They can shade the roof they cover and slightly cut heat entering through it. A UC San Diego study found ceilings under arrays up to 4.5°F cooler by day and modeled a 38 percent drop in that roof's cooling load, but the building was poorly insulated. Well-insulated Texas and Florida homes should expect a smaller effect. The main bill savings come from the electricity the panels make.

Does humidity damage solar panels?

Humidity does not hurt daily output much, but heat and moisture over years can stress panel seals. Kiwa PVEL's 2026 scorecard found 32 percent of tested bills of materials failed its extended damp heat test, mostly from delamination. That is why reliability testing and warranty terms matter more in humid Houston or Miami than in a dry climate. Inspect for delamination or browning if output falls.

Should I pick a west-facing roof in Texas?

West-facing panels make less total energy than south-facing ones in most cases, but they shift output to late afternoon. Whether that is worth it depends on your rate plan or buyback terms. In Texas competitive areas, some plans value evening power more. In Florida net metering, total kWh matters most. Model both orientations in PVWatts and compare with your bill structure.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration